Paul Industries handles laboratory construction for research labs and universities, designing, installing and maintaining the pure water, lab gas, vacuum, HVAC, cleanroom and central plant systems a research building depends on, and moving labs between buildings when programs grow. Headquartered at 256 Shore Drive in Kilmarnock, Virginia, Paul Industries works on university science buildings, institute and hospital research floors, government labs and private research and development sites across the East Coast and in all 50 states. Each project ends with systems that are tested, documented and ready for the investigators who move in.
Request a quote or call 201-450-8280
What does laboratory construction involve for a research building?
Laboratory construction for a research building is mostly mechanical, electrical and plumbing work: a 2026 industry cost review put those systems at roughly half of the cost of a lab project. A research floor needs once-through ventilation for fume hoods, pure water at several grades, piped gases and vacuum at the bench, process cooling for instruments, emergency power for freezers and incubators, and drainage built for the chemicals that go down the sink. An office floor of the same size needs a fraction of that.
Energy follows the same pattern. The Labs21 program run by the EPA and the Department of Energy found that laboratories typically use four to six times as much energy per square foot as a conventional office building, mainly because lab air passes through once and is exhausted rather than recirculated. Research laboratory design decisions such as hood count, sash management, air change rates and heat recovery therefore set the building’s operating cost for decades, and Paul Industries builds them to be measured and tuned after occupancy.
Laboratory construction and renovation also has a client that offices lack: the research itself. Grants run on schedules, samples live in freezers, and instruments lose calibration when they are moved. Every phase plan Paul writes starts with what the investigators need running on each day of the project.
Who handles laboratory construction for research labs and university facilities?
Paul Industries handles laboratory construction for research labs and university facilities, from a single lab renovation to the mechanical systems of a new science building. Universities, research institutes and companies contract with Paul directly, and when a laboratory construction company is running a whole building, Paul Industries carries the lab utilities, piping, high-purity water, controls wiring and startup under one contract with one schedule and one turnover package. For campus planners comparing laboratory construction companies, that scope is the part of the job researchers notice first after move-in.
Paul’s laboratory construction services come in three routes. Supply-only delivers water systems, vacuum and air packages, gas manifolds and pumps with submittals and startup. Under design-build, Paul Industries engineers, fabricates, installs, tests and turns over the whole system. Complete installation builds to the engineer of record’s drawings. For labs that work under GLP or move toward clinical production, Paul adds validation and commissioning with IQ, OQ and PQ protocols, and regulated biomanufacturing sites are covered on the biotech page.
| System | What it serves | Governing codes and standards | What Paul delivers |
|---|---|---|---|
| Pure water | Bench taps, glasswashers, analyzers, cell culture | ASTM D1193, CLSI GP40 | Central RO and DI loops, polishing, distribution, sanitization |
| Lab gases | Instruments, incubators, gas chromatographs, glove boxes | NFPA 45, NFPA 55, ASME B31.3 | Manifolds, cylinder rooms, bulk tanks, piping, alarms |
| Vacuum and compressed air | Filtration, aspiration, drying, pneumatic equipment | NFPA 45, design standards of the institution | Central pump plants, receivers, piping, inlets |
| Lab HVAC and fume hoods | Chemical labs, biosafety labs, instrument rooms | ANSI/ASSP Z9.5, ASHRAE 110, NFPA 45 | Supply and exhaust systems, hood connections, controls, heat recovery |
| Vivarium environments | Animal holding and procedure rooms | Guide for the Care and Use of Laboratory Animals | Air handling, humidity, pressure zoning, cage wash utilities |
| Cleanrooms | Microfabrication, cell work, imaging, particle-sensitive research | ISO 14644 | Envelope, HEPA filtration, pressure cascade, monitoring |
| Central plant and process cooling | Building cooling, instrument and laser cooling loops | ASHRAE 15 | Chillers, closed loops, heat exchangers, pumps |
| Relocation | Moves between rooms, buildings and campuses | DOT Hazardous Materials Regulations | Disconnect, rigging, transport, reinstallation, requalification |
Laboratory water purification systems: central loops and point-of-use polishing
Laboratory water purification systems in a research building usually work in two layers: a central system that makes Type II or Type III water and circulates it through the floors, and point-of-use units that polish that feed to Type I at the bench. The central lab pure water system typically combines pretreatment, reverse osmosis and deionization, with storage and a continuously recirculating loop, while each polisher adds final ion exchange, UV and filtration for analytical work.
A building with a central loop gets better water at more taps for less money than a building where every lab buys a standalone lab water purification system fed from city water, because the polishers last longer and the loop is maintained in one place. Paul Industries builds the central laboratory water system, the loop and the taps, and connects the point-of-use polishers. Where a group needs a dedicated laboratory deionized water system for one instrument suite, Paul installs a lab DI water system on its own loop. A water purification system for laboratory use that serves cell culture or trace analysis is specified by the grade it has to meet, which is why the grades below matter more than brand names. The wider design and construction work is described under ultrapure water systems and industrial DI water systems.
| Grade | Minimum resistivity at 25 C | TOC limit | Typical lab use |
|---|---|---|---|
| ASTM D1193 Type I | 18.0 megohm-cm | 50 ppb | HPLC, mass spectrometry, molecular biology, trace metals |
| ASTM D1193 Type II | 1.0 megohm-cm | 50 ppb | Buffers, media preparation, general reagents |
| ASTM D1193 Type III | 4.0 megohm-cm | 200 ppb | Glassware rinsing, feed to polishers, autoclaves |
| CLSI Clinical Laboratory Reagent Water | Over 10 megohm-cm | Under 500 ppb | Clinical analyzers, with bacteria under 10 CFU/mL |
An ultrapure lab water purification system reading 18.2 megohm-cm sits at the practical ceiling for pure water at 25 degrees Celsius, so at the top grade resistivity by itself says little; TOC, bacteria and endotoxin become the measures that separate a good laboratory ultrapure water system from a poor one. Paul designs loops with continuous velocity, sanitary materials and sample points so those measures stay in range.
Microbial control decides whether a lab water loop stays useful. Water that stands still in a dead leg or a storage tank grows biofilm, and biofilm sheds bacteria and endotoxin into every tap downstream. Paul Industries keeps loops moving at all hours, removes dead legs from older buildings, adds UV and final filtration where the grade calls for them, and builds in a sanitization method, hot water or chemical, with the valves and drains to run it on a schedule. Each loop gets sample valves at the far end of the run as well as at the plant, because the worst water in a building is usually the water farthest from the system that made it.
Laboratory gas piping and specialty gas distribution
Laboratory gas piping carries nitrogen, carbon dioxide, argon, helium, hydrogen, compressed air and specialty mixtures from cylinder manifolds or bulk tanks to benches, incubators and instruments. Clean, leak-tight distribution matters as much as the gas grade: a gas chromatograph fed through dirty tube or a leaking fitting reports the contamination as data.
NFPA 45 governs fire protection for laboratories using chemicals, and NFPA 55 governs compressed gases and cryogenic fluids, including storage quantities, cylinder rooms and separation of incompatible gases. Cryogens need extra care: liquid nitrogen expands about 694 times as it boils to gas at room temperature, so a spill in a small room pushes oxygen below the 19.5 percent OSHA minimum fast, which is why rooms with dewars or bulk liquid get oxygen monitors and ventilation. Paul Industries builds manifolds with automatic switchover so experiments keep running when a cylinder empties, runs cleaned copper or electropolished stainless tube by gas purity, pressure tests and purges every line, and labels each outlet. Piping practice follows Paul’s process piping work.
How does a lab vacuum system work?
A lab vacuum system works by running a central pump plant that holds a receiver tank and a piping network below atmospheric pressure, so each bench inlet pulls a vacuum for filtration, aspiration, drying or vacuum ovens without a pump on every bench. The plant usually has multiple pumps that stage on as demand rises, with one held in reserve, plus controls that alternate run hours.
Laboratory vacuum system design has three concerns beyond pump size. Chemical vapor and liquid get pulled into the pipe, so the system needs traps and filters at the inlets, corrosion-resistant piping and a pump type that tolerates what it receives. Diversity matters, because a building full of inlets never uses them all at once, and oversizing wastes energy while undersizing starves the top floor. Exhaust from the pumps goes outdoors. Paul Industries builds new laboratory vacuum system plants, replaces aging pumps and repairs them through its vacuum pump repair service.
Laboratory HVAC: once-through air, fume hoods and pressure
Laboratory HVAC brings in outdoor air, conditions it, supplies it to the lab and exhausts all of it, because air exhausted from chemical fume hoods is not recirculated under NFPA 45. Labs are generally held negative to corridors so odors and vapors stay inside, and the exhaust stacks are placed so discharged air does not re-enter the building or its neighbors.
Fume hood installation connects a hood to that system and then proves it contains vapors. ASHRAE 110 is the performance test, with face velocity readings over a grid, smoke visualization and a tracer gas release, and ANSI/ASSP Z9.5 calls for routine hood performance testing at least once a year. Many institutions specify an average face velocity between 80 and 120 feet per minute at the working sash height. Variable air volume hoods with sash sensors cut exhaust when sashes close, and heat recovery on exhaust air recovers part of the energy the once-through design spends. Paul installs hoods, exhaust fans, controls and heat recovery, and tests and balances the lab as a system.
Vivarium construction and biosafety lab environments
Vivarium construction builds animal holding and procedure rooms whose environment is part of the research protocol, because temperature, humidity, light and air quality changes show up in the animals’ physiology. The Guide for the Care and Use of Laboratory Animals sets the benchmark of 10 to 15 fresh air changes per hour in animal rooms, with lower rates possible where ventilated cage racks exhaust directly.
A vivarium also needs pressure zoning between clean and soiled corridors, cage wash utilities with high-temperature water and steam, and redundant air handling so a fan failure never reaches the animals. Biosafety labs add containment: the BMBL, now in its sixth edition from the CDC and NIH, describes inward directional airflow and sealed construction for BSL-3 work. Paul Industries builds and maintains these systems, including the cleanrooms used for cell work and microfabrication, and the autoclave installation work that serves cage wash and waste decontamination.
Laboratory relocation services: moving a research lab without losing its work
Laboratory relocation services move instruments, freezers, chemicals, gases and furniture from one lab to another and bring the new lab back into service, and the reinstallation and requalification are where the value lies. Groups searching for laboratory moving companies often find that trucks are the easy part; the hard part is disconnecting utilities safely, keeping samples cold, protecting sensitive optics and getting each instrument working and documented in the new room.
Paul Industries provides lab relocation services as one scope: survey and inventory, utility disconnects, lab equipment moving with rigging for heavy instruments, transport, utility connections in the new space, and startup and requalification. That lab relocation service draws on Paul’s machinery moving and millwright and rigging work for items such as NMR magnets, mass spectrometers, environmental chambers and biosafety cabinets. Chemicals moving over public roads fall under the DOT Hazardous Materials Regulations in 49 CFR Parts 171 to 180, which sets how they are classified, packed and documented. Lab relocation specialists plan around the science: a laboratory relocation is sequenced so each group is down for the shortest possible stretch, and lab equipment relocation for validated instruments ends with documented checks before data collection resumes.
| Phase | Work | Record produced |
|---|---|---|
| Survey | Inventory instruments, freezers, chemicals and gases; confirm utilities in the new room | Move inventory and utility matrix |
| Pre-move | Schedule each group’s downtime, order crates and shock loggers, line up temporary freezer space | Move schedule by lab |
| Decommission | Disconnect water, gas, vacuum, exhaust and power; decontaminate equipment | Decontamination and disconnect sign-offs |
| Transport | Rig, pack and move equipment; move chemicals under DOT rules; keep samples cold | Chain of custody and temperature logs |
| Reinstall | Set, level and anchor equipment; connect utilities; leak test gas and water lines | Installation and leak test records |
| Requalify | Start up, calibrate and run IQ and OQ where the instrument is validated | Startup sheets and qualification reports |
Lab renovation and lab decommissioning in occupied research buildings
Lab renovation in an occupied research building means rebuilding one floor or suite while the labs above, below and beside it keep running experiments that cannot tolerate dust, vibration or a lost utility. Paul Industries plans shutdowns of shared water, gas, vacuum and exhaust systems with every group on the affected riser, uses temporary feeds where an outage would ruin work, and isolates the construction zone so its air never reaches the operating labs.
Vibration and electromagnetic noise deserve their own plan. Electron microscopes, NMR systems and optical tables respond to footfall, pumps and core drilling on adjacent floors, so Paul Industries schedules heavy demolition and drilling around imaging sessions, isolates new pumps and fans on inertia bases and flexible connectors, and keeps new mechanical equipment away from instrument rooms where the layout allows.
Lab decommissioning is the opposite job: making a lab safe to renovate, reassign or demolish. Equipment and surfaces are decontaminated, chemicals and gas cylinders are removed, drain traps and exhaust ducts that held residue are cleaned or removed, and utilities are capped at the main. Institutions keep the decommissioning records with the building file, and Paul Industries delivers them with the work.
What is laboratory construction cost per square foot?
Laboratory construction cost per square foot ranged from about $600 to $1,400 in a 2026 industry cost review, counting construction only and excluding equipment, design fees and technology and security systems. The same review gave average fit-out costs of about $700 to $800 per square foot for BSL-1 and BSL-2 labs, about $800 for chemistry labs, and about $1,000 to $1,300 for BSL-3 labs and vivariums, with Boston named among the high-cost markets.
Mechanical and electrical systems drive most of the spread. Hood count and air change rates set the size of air handlers and exhaust fans; pure water grade and loop length set the water system; containment level adds sealed construction, redundant exhaust and decontamination; and renovation inside an occupied building adds phasing and temporary utilities. Paul Industries gives a budget range from comparable scope early and a firm price once the scope is defined. Send the program, room list or drawings, the hood and water requirements and the target occupancy date.
Emergency power and alarms for freezers and critical lab equipment
Emergency power in a research building protects years of work stored in ultra-low freezers, incubators, cryogenic storage and animal facilities, so a lab’s electrical and alarm design is part of its research protection. Paul Industries connects freezers, incubators, vivarium fans and controls, vacuum and air plants, and process cooling pumps to the standby system, and stages their restart so motor loads come back in sequence after a transfer.
Power is half the protection; the other half is knowing when something fails. Freezer and incubator alarms, low-oxygen monitors in cryogen rooms, gas manifold alarms, water quality monitors and vivarium environmental alarms all report to the building automation system or a dedicated monitoring platform that reaches a person at night and on weekends. Paul installs and wires those points, tests each alarm end to end, and gives the facility a points list that matches what is in the field.
Laboratory construction standards and codes
Laboratory construction standards cover fire safety, ventilation, water quality, animal care and biosafety, and each applies to a different system in the building. NFPA 45 covers fire protection in labs that use chemicals, and NFPA 55 covers compressed gases and cryogens. ANSI/ASSP Z9.5 governs lab ventilation, with ASHRAE 110 as the hood test. ASTM D1193 and CLSI GP40 define reagent water grades. The Guide for the Care and Use of Laboratory Animals sets vivarium conditions, and the BMBL sets biosafety containment practice. OSHA 29 CFR 1910.1450, the Laboratory Standard, requires a chemical hygiene plan that relies on working hoods and ventilation. ASME B31.3 governs process piping, ASHRAE 15 refrigeration machinery, and ISO 14644 any classified cleanroom. Paul builds to the edition the authority and the institution’s own design standards call for.
Campus central plants and process cooling for research buildings
Campus central plants supply research buildings with chilled water and steam, and labs run those utilities around the clock and through every season, unlike classrooms. Instruments such as lasers, electron microscopes and NMR systems add process cooling loops that need steady temperature and clean water, usually on a closed loop separated from the campus system by a heat exchanger. Paul Industries builds and services the chillers, pumps, heat exchangers and loops on both sides, described further under chilled water systems, and plans plant outages around the buildings that cannot lose cooling.
Research lab projects across the East Coast, the 50 states and other countries
Paul Industries began in northern New Jersey, moved to Pennsylvania, and now runs its East Coast work from 256 Shore Drive in Kilmarnock, Virginia, with laboratory projects open in all 50 states. Research clusters from Boston and Cambridge through New York, New Jersey, Philadelphia, Maryland, Northern Virginia and the North Carolina Research Triangle run on the same lab systems and standards. Academic medical centers often pair research towers with hospitals, which Paul serves through its hospitals and healthcare work. Research sites abroad are covered on the international page, and the full list of sectors Paul works in sits on the industries overview.
Laboratory systems and lab moves from Paul Industries
For research labs and universities, Paul Industries is the contractor that designs, supplies, fabricates, installs, starts up, tests, validates, maintains, services and repairs the building’s lab utilities: pure and ultrapure water, lab gases and vacuum, fume hood and vivarium HVAC, cleanrooms, process cooling and central plant equipment, and the relocations that carry a lab from one building to the next. Institutions choose supply-only, design-build or complete installation, and every job closes with test records the facility and safety offices keep. Send the program, drawings or move inventory and request a quote.
Standards referenced: ASTM D1193 · CLSI GP40 (Clinical Laboratory Reagent Water) · NFPA 45 · NFPA 55 · ANSI/ASSP Z9.5 · ASHRAE 110 · Guide for the Care and Use of Laboratory Animals (8th edition) · Biosafety in Microbiological and Biomedical Laboratories (BMBL), 6th edition · OSHA 29 CFR 1910.1450 (Laboratory Standard) · DOT Hazardous Materials Regulations, 49 CFR Parts 171-180 · ISO 14644 · ASME B31.3 · ASHRAE 15
Frequently asked questions
How much does a lab water purification system cost to install?
Cost depends on the grade of water, the daily volume, the number of taps and how far the loop runs. A central system adds pretreatment, RO, deionization, storage, a recirculating loop and sanitization, while point-of-use polishers add a smaller cost per bench. Renovation in an occupied building adds routing and shutdown work. Paul Industries prices from the tap list, water grades and floor plans, starting with a budget range and then a firm number.
Which lab water grade does a research lab need: Type I, Type II or Type III?
The grade follows the work. Type I water at 18.0 megohm-cm or higher serves HPLC, mass spectrometry, molecular biology and trace analysis. Type II suits buffers, media and general reagents. Type III serves glassware rinsing and feeds polishers and autoclaves. Most research buildings run a central Type II or Type III loop and polish to Type I at the bench, which gives every grade without a separate pipe for each.
Why is purified water always used in the laboratory?
Tap water carries dissolved minerals, chlorine or chloramine, organics, particles and bacteria that interfere with experiments. Ions shift pH and conductivity, organics raise background in chromatography, bacteria and endotoxin affect cell culture, and minerals leave spots on glassware. Purified water removes those variables so results reflect the experiment rather than the water supply, and graded water lets labs match purity to the sensitivity of each method.
How is a research lab relocated without losing qualification or months of work?
The move is planned lab by lab around the science. Samples move to temporary freezer space or move cold with temperature logging, instruments are packed with shock loggers, and utilities in the new room are ready and tested before equipment arrives. Validated instruments get IQ and OQ in the new location before data collection resumes. Paul Industries sequences groups so each is down for the shortest stretch and hands over records for every instrument.
What does a lab relocation company handle before move day?
Most of a move happens before the truck arrives. A lab relocation company surveys every room, builds an inventory of instruments, freezers, chemicals and gas cylinders, confirms that water, gas, vacuum, exhaust and power are ready in the new space, orders crates, sets each group’s downtime window and plans how chemicals move under DOT rules. Paul Industries also decontaminates and disconnects equipment and records each step for the institution’s safety office.
Who installs central DI water loops and lab gas piping for university buildings in North Carolina and Maryland?
Paul Industries installs central RO and DI water loops, lab gas manifolds and piping, and vacuum plants for university and institute buildings in North Carolina, Maryland and across the East Coast, from its headquarters in Kilmarnock, Virginia, and in all 50 states. Work covers new buildings and renovations of occupied floors, with pressure tests, purges, water quality results and as-built drawings at turnover.
Does lab construction cost more in Boston and New York?
Market location moves lab costs, and a 2026 industry cost review named Boston among the high-cost markets alongside the San Francisco Bay Area and San Diego. Labor rates, union conditions, building age, permitting and tight urban sites all add cost, and older buildings in dense cities often need more structural and riser work to host lab systems. Paul Industries prices each project from the actual scope and site conditions.
How are minus 80 freezers and liquid nitrogen dewars moved in a lab relocation?
Freezer contents usually move separately from the freezer: samples go to temporary units or ride in dry ice or LN2 shippers with temperature logging, and the empty freezer moves upright and rests before restart so its compressor oil settles. Dewars move secured and vented, never in a closed passenger space, because boiling nitrogen displaces oxygen. Paul Industries plans the sequence so samples spend the least possible time outside a running freezer.
How often should laboratory fume hoods be tested?
ANSI/ASSP Z9.5 calls for routine performance tests at least once a year, and again after any change that could affect performance, such as a new exhaust fan, a moved hood or rebalanced supply air. Annual checks usually measure average face velocity and confirm the airflow monitor. Full ASHRAE 110 testing with tracer gas applies at commissioning and after major changes. Paul Industries tests hoods as part of installation and balancing.
Is lab exhaust ever recirculated to save energy?
Chemical fume hood exhaust is not recirculated under NFPA 45, and general lab exhaust is normally sent outdoors too. Energy is saved in other ways: variable air volume hoods that reduce exhaust when sashes close, lower air change rates in labs that pass a hazard review, run-around coil or other heat recovery that never mixes exhaust with supply air, and occupancy-based setbacks. Paul Industries installs and tunes those measures.
What is lab decommissioning and when is it required?
Lab decommissioning prepares a lab space for a new occupant, renovation or demolition by removing chemicals, biological materials, gas cylinders and radioactive sources, decontaminating surfaces and equipment, and documenting that the space is safe. Institutions require it when an investigator leaves, a lab changes hazard class or a renovation begins. Paul Industries cleans or removes contaminated drains and exhaust ducts and caps utilities as part of the work.
How is a vivarium environment kept stable for animal research?
Stability comes from redundant air handling, tight temperature and humidity control and continuous monitoring with alarms. Animal rooms run at 10 to 15 fresh air changes per hour under the Guide unless ventilated racks exhaust directly, and pressure zoning keeps clean and soiled corridors apart. Emergency power covers the fans and controls. Paul Industries builds and services these systems and trends their data so drift is fixed before it affects a study.
What does a central lab vacuum system need besides pumps?
A central vacuum plant needs a receiver tank, controls that stage pumps and alternate run hours, a reserve pump, exhaust piped outdoors, and piping sized for diversity across all the inlets in the building. At the bench, inlets need traps or filters that keep liquids and vapors out of the pipe. Corrosion-resistant piping and pumps suited to chemical vapor extend the system’s life. Paul Industries designs and builds all of it.
Can a lab renovation proceed while neighboring labs keep working?
Yes, with planning. Shared risers are mapped so every group on a water, gas, vacuum or exhaust line knows when it goes down, and temporary feeds keep critical work running during tie-ins. The construction zone is sealed and held negative so dust stays inside, and vibration-heavy work is scheduled around sensitive instruments. Paul Industries agrees the plan with the building manager and affected investigators before work starts.
What paperwork does a university receive after lab systems are installed?
The turnover package includes as-built drawings, equipment submittals and manuals, pressure and leak test records for gas and vacuum lines, water quality results and sanitization records, fume hood test and balancing reports, startup sheets, and training records for facility staff. Validated systems add IQ and OQ reports. The package is organized so the facility and safety offices find each record quickly.
How does a research lab differ from a GMP lab in mechanical terms?
A research lab is built for flexibility and safety: systems serve changing experiments and the controls protect people. A GMP lab or production suite is built for documented consistency: systems are designed to a defined process, validated and changed only under change control, with water and air quality trended against specifications. Many university buildings hold both, and Paul Industries builds each area to its own standard.
Can Paul Industries build lab water and gas systems for research sites in Ireland or the United Kingdom?
Yes. Paul Industries takes laboratory projects in Ireland and other countries, including pure water systems, lab gas and vacuum distribution, fume hood HVAC and lab moves. Equipment is specified for the host country’s voltage and frequency, and the work follows the codes that apply at the site alongside the international standards research organizations share, such as ISO 14644 for cleanrooms.
How do lab gas manifolds switch over without interrupting experiments?
An automatic switchover manifold holds two banks of cylinders, a primary and a reserve. When the primary bank’s pressure drops to a set point, the manifold switches to the reserve with no interruption downstream and signals that the empty bank needs replacing. Pressure regulators and alarms are sized for the flow and purity of the gas. Paul Industries installs manifolds, alarms and the piping that connects them to each lab.
Building, renovating or moving a research lab?
Send the program, room list or drawings, the water, gas and hood requirements, or the move inventory. Call 201-450-8280 or request a quote.
