Paul Industries delivers cold storage construction for refrigerated and freezer warehouses, designing, fabricating, installing and starting up the refrigeration plant, piping, underfloor heating, controls and utilities that hold a building at temperature. The building shell, insulated panels and racking set the box; the mechanical systems decide whether product stays frozen, whether the floor stays flat and whether the refrigeration plant passes its first process safety audit. Paul Industries works for developers, contract logistics operators, food and beverage producers and pharmaceutical distributors, on new buildings, expansions and retrofits of operating warehouses, with supply-only, design-build and complete installation routes.

Request a quote or call 201-450-8280

Headquarters 256 Shore Drive, Kilmarnock, Virginia
Where All 50 states and plants outside the United States
Freezer rooms Commonly -10 to -20 F; blast freezers often below -30 F
Ammonia rules OSHA PSM and EPA RMP at 10,000 lb; general duty clause below that
New refrigerant limit Interim 700 GWP cap for new cold storage systems from July 27, 2026 (EPA)
Build cost Almost double an ambient warehouse (Cushman & Wakefield, 2024)
Reviewed November 2026

What is a cold storage warehouse?

A cold storage warehouse is a building whose storage rooms are held below ambient temperature by a refrigeration system, from coolers just above freezing to freezers well below 0 F, so that food, beverages, pharmaceuticals and other perishable goods keep their quality and safety between production and sale. The difference from a regular warehouse is that the building itself becomes part of the refrigeration system. Every wall, roof and floor is a thermal and vapor barrier, every door is a heat leak, and the floor slab sits on insulation that would let the soil beneath freeze if nothing kept it warm.

A dry distribution center runs on lighting, dock equipment and a modest HVAC load. A freezer building of similar size adds an engine room or rooftop refrigeration units, evaporators hung over the racks, condensers rejecting the heat outdoors, a sub-slab heating loop, defrost systems, heated door frames and a far larger electrical service. Cushman & Wakefield notes that a freezer facility may need roughly 4 megawatts of power or more, depending on size, which makes utility capacity one of the first questions on any site.

Cold storage warehouse temperatures and what each room asks of the building

Cold storage warehouse temperatures range from coolers held in the 30s F for produce, dairy and beverages, through holding freezers commonly run between -10 and -20 F, down to blast freezers that often operate below -30 F to pull heat out of product quickly. Each band changes the refrigeration plant, the insulation thickness, the floor design and the defrost method, so the room schedule is the first document in any cold storage warehouse design.

Typical room types in a refrigerated warehouse and what each one drives
RoomTypical conditionMechanical consequence
Refrigerated dockAbout 35 to 45 FHigh infiltration from truck doors; dehumidification and door seals keep frost off the freezer entries
CoolerAbout 32 to 40 F for produce, dairy and beveragesSingle-stage refrigeration, humidity control for produce, off-cycle or air defrost
Pharmaceutical refrigerator2 to 8 C (36 to 46 F), USP definitionRedundant cooling, tight control band, temperature mapping and continuous monitoring
Holding freezerCommonly -10 to -20 FTwo-stage or low-temperature systems, hot gas or electric defrost, heated floor sub-base
Pharmaceutical freezer-25 to -10 C (-13 to 14 F), USP definitionAlarmed backup cooling, mapped storage zones, documented excursions
Blast freezer or spiral freezerOften below -30 FVery high refrigeration load per square foot, frequent defrost, dedicated suction level

Mixed-temperature buildings are now common, with a freezer, a cooler and a refrigerated dock under one roof. Running each room from the right suction level, rather than serving everything at the coldest one, is where most of the lifetime energy cost of the building is set.

Refrigerated warehouse construction: what the mechanical scope covers

Refrigerated warehouse construction combines an insulated building envelope with a refrigeration plant, a heated floor, fire protection suited to freezing rooms and a large electrical service, and the mechanical scope is everything inside that envelope that moves heat, fluid or power. Cold storage construction services from Paul Industries cover the following elements, each designed around the room schedule and the operator’s racking and material handling plan.

Mechanical elements of cold storage warehouse construction
ElementWhy it mattersWhat Paul Industries delivers
Refrigeration plantHolds every room at its set point through peak summer loads and door trafficEngine room or packaged units, compressors, condensers, vessels, controls and startup
Refrigeration pipingWelded steel or stainless lines carry refrigerant between plant and evaporatorsFabrication, installation, pressure testing, labeling and insulation of every line
Evaporators and defrostCoils over racks must shed frost without warming productUnit coolers, valve groups, hot gas or electric defrost, drain line heat trace
Underfloor heatingKeeps soil below a freezer slab from freezing and heaving the floorGlycol loops warmed with recovered refrigeration heat, or electric cable in conduit, with monitoring
Penetrations and vapor controlEvery pipe, conduit and support through a panel is a path for moisture and iceSealed and insulated penetrations, vapor retarder continuity, insulated hangers
Fire protection pipingWet sprinkler pipe freezes in rooms below 40 FDry pipe or preaction piping runs and valve rooms located in heated space
Electrical and controlsCompressors, fans, heaters and doors draw megawatts and need coordinated controlPower distribution, motor control, PLC and supervisory controls, alarm and temperature logging
Rigging and settingCompressors, vessels and condensers weigh tons and often go on roofsCrane planning, setting, leveling, anchoring and alignment

Building a cold storage warehouse also brings utilities that a dry building does not need: makeup water and treatment for evaporative condensers, condensate drains run through heated chases, and dock dehumidification. Paul Industries carries the heat tracing for drains and door frames, the mechanical insulation for cold piping, and the electrical services that feed the plant, so the mechanical package arrives at substantial completion as one coordinated system.

Who builds refrigeration and mechanical systems for cold storage facilities?

Paul Industries builds the refrigeration, piping, controls and utility systems for cold storage facilities as a cold storage construction company that designs, fabricates, supplies, installs, tests, starts up and maintains the mechanical side of a refrigerated warehouse. Owners and general contractors bring Paul Industries in at concept stage to size the plant and settle the refrigerant, at design-build stage to deliver the full mechanical package, or after handover to service, expand and retrofit an operating building.

Developers comparing cold storage warehouse builders tend to focus on the shell. The mechanical scope is where the schedule risk and the operating cost sit, and it is the scope Paul Industries delivers under one contract: refrigeration plant, piping, underfloor heating, insulation, electrical, controls, commissioning and the process safety documents an ammonia plant needs at startup. One accountable contractor carries the design intent from the load calculation through to the last valve tag.

  • New freezer warehouse construction for distribution and contract logistics operators
  • Production-attached cold stores at meat and poultry plants and food and beverage plants
  • Expansions that add rooms or suction levels to an existing engine room
  • Refrigerant conversions, plant replacements and controls upgrades in operating buildings
  • Pharmaceutical and biologic storage with mapped, monitored rooms

Cold storage refrigeration: choosing the system for the building

Cold storage refrigeration for a warehouse is chosen by charge size, room temperatures, building size, operator preference and the regulations each refrigerant brings, and the main options are a central ammonia plant, low-charge packaged ammonia units, an ammonia and carbon dioxide cascade, and halocarbon racks. Each one can hold a freezer at -20 F. They differ in where the refrigerant lives, how much of it there is, and which rules apply to it.

Cold storage refrigeration system options compared
OptionHow it is arrangedCharge and regulationWhere it fits
Central ammonia plantEngine room with screw compressors, vessels and evaporative condensers; pumped or flooded liquid to unit coolersLarge charges; OSHA PSM and EPA RMP at 10,000 lb and above, general duty clause below; IIAR 2 and IIAR 9Large freezers and multi-temperature distribution centers
Low-charge packaged ammoniaFactory-built units on the roof or pad, each serving a zone with a few pounds of ammonia per tonSmall charge per unit; often below PSM and RMP thresholds, still under the general duty clause and IIAR standardsNew buildings that want ammonia without an engine room
Ammonia and CO2 cascadeAmmonia confined to the machine room condenses carbon dioxide, which is pumped to the freezer coilsAmmonia charge shrinks and stays out of storage rooms; CO2 side runs at high pressureFreezers with occupied work areas and operators wanting ammonia out of the rooms
Halocarbon rack or split unitsCopper-piped HFC or HFO systems with remote condensersEPA Technology Transitions GWP limits on new cold storage systems; leak rules on larger chargesSmaller coolers, walk-in freezers inside plants, and add-on rooms

Each option is also an energy decision. An engine room centralizes maintenance and lets several suction levels share compressors, while distributed packaged units shorten piping and limit any release to one zone. Paul Industries prices the options against the owner’s room schedule, utility rates and staffing model before the refrigerant is fixed, because changing it after the structural steel is designed is expensive.

Cold storage refrigeration system design

Cold storage refrigeration system design starts with a load calculation for each room: transmission through panels and floor, infiltration through doors, product pull-down, people, lift trucks, lighting, fans and defrost heat. From those loads come the suction levels, compressor staging, condenser size and evaporator layout. Coil placement has to clear rack flue spaces and sprinkler heads, throw air the length of the aisles, and drain defrost water into heated lines. A complete cold storage refrigeration system design package includes the flow diagram, the P&ID, line sizing, relief calculations, control narrative and equipment schedule, and for ammonia plants it becomes part of the process safety information.

Paul Industries designs and installs each ammonia refrigeration system for cold storage, and its ammonia refrigeration service covers compressors, vessels, piping, PSM documentation and maintenance in depth. On a warehouse project, that work sits inside the larger construction schedule: the engine room has to be ready for the compressors when the panels close in, and pull-down of a freezer has to be staged slowly so the floor and the panels are not stressed.

Cold storage refrigeration equipment and units

Cold storage refrigeration equipment includes compressors, evaporative or air-cooled condensers, receivers and recirculators, unit coolers, valve groups, purgers, detection and ventilation, and the controls that tie them together. Cold storage refrigeration units, whether packaged ammonia skids, CO2 systems or halocarbon condensing units, are supplied by Paul Industries or installed as owner-furnished equipment, and either way they arrive at a prepared pad or roof curb with piping, power and controls ready to connect.

Spiral freezer, blast freezer and walk in freezer installation

Spiral freezers, blast freezers and walk-in freezers are the high-load and small-room ends of a cold storage building, and each needs installation work that differs from the bulk storage freezer. Paul Industries sets, pipes, wires, starts up and maintains all three, in production plants and in distribution buildings.

Spiral freezer installation

A spiral freezer carries product on a belt that climbs or descends in a helix inside an insulated enclosure, so a long freezing path fits into a small floor area, and it suits continuous lines of meat, poultry, bakery and prepared foods. Installation covers rigging the enclosure and drum, connecting it to a dedicated low-temperature suction level, hot gas or water defrost piping, belt wash and drain connections, and integration with upstream and downstream conveyors. Sanitation access drives much of the layout, because the freezer is cleaned on a schedule set by the product.

Blast freezer installation

Blast freezer installation puts a large refrigeration capacity into a small insulated room, with high-velocity air moving across pallets or carts of warm product. The coil and fans are sized for the pull-down rate, not the holding load, so the room needs its own suction level or a generous share of the plant, frequent defrost, and floor protection beneath it. Paul Industries also converts existing rooms to blast duty when an operator’s product mix changes.

Walk in freezer installation

Walk in freezer installation inside a plant or warehouse joins insulated panels, a floor, a door and a refrigeration system into a room under 3,000 square feet, the size limit in the federal walk-in definition, with component efficiency standards set by the Department of Energy. In industrial buildings these rooms hold ingredients, samples, quarantine stock or retained product. Paul Industries installs the panels and refrigeration, ties the room into the plant’s controls and alarms, and connects it to a central ammonia or glycol system where that is more efficient than a standalone condensing unit.

Pharmaceutical cold chain warehouse work

A pharmaceutical cold chain warehouse stores medicines, vaccines and biologics inside the USP temperature definitions, refrigerator at 2 to 8 C and freezer at -25 to -10 C, and it has to prove that every pallet position stayed in range. That proof comes from temperature mapping of each room loaded and empty, continuous monitoring with calibrated sensors, documented alarm response, and refrigeration redundancy sized so that a single failure never lets a room drift out of range.

Paul Industries builds these rooms with redundant refrigeration circuits, monitored backup power connections and controls that log every excursion, then supports mapping and qualification through its validation and commissioning work. Food warehouses carry a parallel duty: under FDA’s 21 CFR 117.206, a facility that only stores unexposed packaged food needing temperature control must still set temperature controls, monitor them, take corrective action when control is lost, verify its instruments and keep the records. Building the monitoring into the controls from the start makes both regimes easier to meet.

Cold storage warehouse requirements: codes and standards

Cold storage warehouse requirements come from the refrigeration codes, process safety rules, fire codes, energy standards and product regulations that apply to the building, and which ones govern depends on the refrigerant, the charge and what is stored. The table lists the main documents Paul Industries designs and builds to on a refrigerated warehouse.

Codes and standards that govern cold storage facility construction
DocumentWhat it coversEffect on the project
ANSI/IIAR 2Design and installation of closed-circuit ammonia refrigeration systemsMachinery room ventilation, detection, relief, piping and equipment requirements for new ammonia work
ANSI/IIAR 9Minimum safety criteria for existing ammonia systemsInitial safety evaluation of each existing system was due by January 1, 2026, with periodic revalidation
ASHRAE Standard 15Safety standard for refrigeration systemsMachinery room and occupancy rules for halocarbon and other refrigerants
ASME B31.5Refrigeration piping and heat transfer componentsMaterials, welding and testing of refrigerant piping
OSHA 29 CFR 1910.119 and EPA 40 CFR Part 68Process Safety Management and Risk Management ProgramApply to ammonia systems holding 10,000 lb or more; the Clean Air Act general duty clause applies below that
EPA Technology Transitions ruleRefrigerant global warming potential limits for new systemsInterim 700 GWP limit for new cold storage systems from July 27, 2026; 150 or 300 limits from January 1, 2032
NFPA 13Sprinkler system installationDry pipe or preaction systems wherever piping cannot be kept at or above 40 F
10 CFR 431 Subpart RDOE walk-in cooler and freezer standardsComponent efficiency for walk-ins under 3,000 square feet
FDA 21 CFR 117.206Storage of refrigerated packaged foodTemperature control, monitoring, corrective action and records

Ammonia sits outside the Technology Transitions limits because its global warming potential is zero, and carbon dioxide’s is one. For halocarbon systems, the May 2026 EPA rule moved the original cold storage limits of 150 GWP for charges of 200 pounds or more, and 300 GWP for smaller charges or the high side of a cascade, out to January 1, 2032. Paul Industries designs and installs refrigeration work to these documents and supplies the records each one asks for at turnover.

Expanding or retrofitting a cold storage facility while it operates

Expanding or retrofitting a cold storage facility while it operates means keeping product at temperature while the refrigeration plant, piping or controls are changed around it, and that takes phased work planned room by room. Cushman & Wakefield expects the average age of US cold storage inventory to stay around 35 years, so a large share of the work on the market is in buildings that cannot empty for a rebuild.

Paul Industries plans each retrofit around the stock: which rooms can be consolidated, how much spare compressor capacity exists, where temporary refrigeration is needed, and how new piping can be tied in during short isolations. Typical scopes include adding a freezer bay to an existing engine room, converting a halocarbon plant to ammonia or a cascade, replacing reciprocating compressors with screw machines, replacing failed underfloor heating, re-insulating iced piping, and replacing obsolete controls with a PLC system. Tie-ins are scheduled under written procedures through the shutdown and turnaround process, and heavy equipment moves through millwright and rigging work.

Frost heave is the retrofit that owners notice last and pay for most. When a sub-slab heating loop fails, the soil freezes slowly and the floor rises, cracking slabs and throwing rack columns out of plumb. Paul Industries locates the failure, restores heat with glycol or electric systems, and monitors the sub-base temperature afterward so that a heater fault raises an alarm long before the slab moves.

What is the cost of cold storage construction?

The cost of cold storage construction runs well above a dry warehouse because of the insulated envelope, the refrigeration plant, the heated floor, freeze-protected fire sprinklers and the electrical service, and Cushman & Wakefield reported in 2024 that new cold storage costs almost double ambient warehousing. Freezer space costs more than cooler space, and smaller buildings cost more per square foot than large ones because the plant and the envelope do not shrink in proportion.

Cold storage warehouse construction cost is driven by the following, roughly in order of weight on a new building:

  • Room temperatures and how much of the building is freezer, cooler or dock
  • Refrigerant and system type, including whether an engine room is built
  • Clear height and building volume, which set panel area and air volume
  • Utility capacity at the site, and whether a new service or substation is needed
  • Automation, such as automated storage and retrieval systems, which change the room design
  • Pharmaceutical requirements: redundancy, mapping and qualification
  • Regional labor rates, seismic and wind design, and the owner’s schedule

For an expansion or retrofit, the cold storage warehouse cost depends more on the existing plant: spare capacity, the condition of piping and vessels, the controls platform and how much work must be phased around stock. Paul Industries gives a budget range from comparable scope as soon as the room schedule and site are known, then a firm price once the design is set.

East Coast headquarters, all 50 states and international projects

Paul Industries is headquartered at 256 Shore Drive in Kilmarnock, Virginia, and builds and services refrigerated warehouses along the East Coast, from the distribution corridors of New Jersey and Pennsylvania through Maryland, Virginia and the Carolinas to Georgia and Florida, and in every other state. Cold storage operators often run networks of buildings in several regions, and one contractor across the network keeps equipment, controls and documentation consistent. Paul Industries also takes cold storage work at plants and warehouses outside the United States; the international page describes how those projects run.

Cold storage construction from Paul Industries

Paul Industries is one of the cold storage construction contractors that carries the full mechanical package: refrigeration design and equipment supply, piping fabrication and installation, underfloor heating, insulation, power and controls, startup, documentation and ongoing maintenance, on new freezer buildings, production-attached cold stores and retrofits of operating warehouses. Owners compare cold storage construction companies on schedule, accountability and the condition of the building after five winters; Paul Industries answers for all three under one contract. See the full list of industries Paul Industries serves, or send the room schedule, site location and target dates and request a quote.

Standards referenced: ANSI/IIAR 2 · ANSI/IIAR 6 · ANSI/IIAR 9 · ASHRAE Standard 15 · ASME B31.5 · ASME Section VIII · OSHA 29 CFR 1910.119 (Process Safety Management) · EPA 40 CFR Part 68 (Risk Management Program) · Clean Air Act Section 112(r)(1) general duty clause · EPA Technology Transitions rule (40 CFR Part 84) · NFPA 13 · DOE walk-in cooler and freezer standards, 10 CFR 431 Subpart R · FDA 21 CFR 117.206 · USP General Notices storage temperatures

Frequently asked questions

How cold are refrigerated warehouses?

Refrigerated warehouses usually hold coolers in the low to mid 30s F for produce, dairy and beverages, and freezers commonly between -10 and -20 F. Blast freezers run colder, often below -30 F, because they pull heat from warm product rather than holding frozen stock. Pharmaceutical rooms follow USP definitions: 2 to 8 C for refrigerated product and -25 to -10 C for frozen. Paul Industries designs the refrigeration plant around the room schedule an operator sets.

What is the cold storage construction cost per square foot?

Published per-square-foot figures for cold storage vary widely, because they bundle different temperatures, clear heights, automation and site work. Cushman & Wakefield reported in 2024 that new cold storage costs almost double ambient warehousing, with freezer space at the upper end. Paul Industries prices the mechanical package from the actual room schedule, refrigerant choice and site utilities, gives a budget range from comparable scope early, and firms the price once design is complete.

What is the cost to build cold storage warehouse space inside an existing dry building?

Converting dry space adds an insulated panel box, a new or extended refrigeration system, a heated floor for any freezer, freeze-protected sprinklers and more electrical capacity. The existing slab often has to be removed or overlaid with insulation and a new wearing slab, which makes freezer conversions close to new construction in scope. Cooler conversions are lighter. Paul Industries surveys the building and utilities and then prices the conversion against a new building on the same site.

What does a cold storage refrigeration system price depend on?

The price of a cold storage refrigeration system depends on total refrigeration load, the number of suction levels, the refrigerant, whether an engine room is built or packaged units are used, condenser type, piping length, controls and the documentation the refrigerant requires. A central ammonia plant brings process safety work; a halocarbon system brings refrigerant cost and leak rules. Paul Industries prices the options side by side from the owner’s room schedule.

Which refrigerant suits a new freezer warehouse in 2026?

Ammonia, whether in a central plant or low-charge packaged units, and ammonia with carbon dioxide in a cascade are the usual choices for large freezers, because neither is restricted by EPA global warming potential limits. Halocarbon systems still fit small rooms and add-ons, and from July 27, 2026 new cold storage systems face an interim 700 GWP cap, with tighter limits from 2032. Paul Industries compares the options on energy, charge, regulation and maintenance before design is fixed.

Does an ammonia system under 10,000 pounds still carry federal safety duties?

Yes. OSHA Process Safety Management and the EPA Risk Management Program apply at 10,000 pounds of ammonia or more, but the Clean Air Act general duty clause covers smaller systems, and EPA has enforced it at warehouses and food plants. The clause expects the owner to identify hazards, design and maintain a safe system and minimize the consequences of a release. Paul Industries builds sub-threshold plants to IIAR 2 and documents them accordingly.

Why do freezer warehouse floors need heating underneath?

Floor heating keeps the soil beneath a freezer above freezing. A freezer slab sits on thick insulation, but over years heat still leaves the ground, and once the soil freezes, ice lenses form and lift the slab. That frost heave cracks floors, tilts racks and damages doors. Glycol loops warmed with recovered refrigeration heat or electric cables in conduit supply the heat. Paul Industries installs, monitors and repairs both kinds.

How are sprinklers protected in a freezer warehouse?

NFPA 13 calls for dry pipe or preaction systems wherever sprinkler piping cannot be reliably kept at or above 40 F, which covers freezers and most coolers. The valves sit in heated space, and the piping is pitched to drain. Moisture in the compressed air feeding the system must be kept low, because condensation inside freezer piping turns to ice plugs. Paul Industries lays out sprinkler runs alongside evaporators, racks and refrigeration piping during design so nothing clashes in the field.

Can a cold storage warehouse be expanded without emptying it?

Yes, with phasing. New rooms are built and pulled down first, then connected to the existing plant during planned isolations, and stock moves into the new space before older rooms are reworked. Spare compressor capacity, temporary refrigeration and the timing of each tie-in decide how smoothly it goes. Paul Industries writes the phasing plan with the operator so that inventory, receiving and shipping keep moving through the work.

How long does refrigerated warehouse construction take?

Schedules depend on building size, permitting, equipment lead times and the refrigerant, and long-lead items such as compressors, condensers, switchgear and transformers often set the critical path. Freezer pull-down also takes time, because rooms are cooled in stages so the slab and panels are not shocked. Paul Industries releases long-lead equipment early in a design-build contract and sequences the engine room, piping and controls to suit panel close-in.

Who builds cold storage facilities in New Jersey and Pennsylvania?

Paul Industries builds and retrofits the refrigeration, piping, floor heating, electrical and controls for cold storage facilities across New Jersey and Pennsylvania, where food distribution and contract logistics buildings serve the New York and Philadelphia markets. Many of those buildings are older ammonia plants due for IIAR 9 evaluation follow-up, controls replacement or added freezer capacity, and Paul Industries scopes that work around continued operation.

Does Paul Industries work on cold storage in Georgia, Florida and the Carolinas?

Yes. Paul Industries delivers cold storage construction and refrigeration retrofits across Georgia, Florida, North Carolina and South Carolina, where hot, humid summers push condenser and dock loads high. In those climates dock dehumidification, door seals and condenser capacity on the hottest days get extra attention in design, and evaporative condenser water treatment matters through the long cooling season.

Can Paul Industries deliver a cold storage project outside the United States?

Yes. Paul Industries takes refrigerated warehouse and production cold store projects at sites abroad, for example in Canada, Mexico and the Caribbean, delivering design, fabricated piping, equipment supply, installation and startup. The design follows the codes adopted where the building stands, alongside the owner’s corporate standards, and documentation is prepared for the authority having jurisdiction. The international page covers how these projects are organized.

What should a cold chain operator expect from temperature mapping?

Temperature mapping places calibrated loggers through a room, at different heights and near doors, coils and walls, and records conditions over a period long enough to capture door traffic, defrost and seasonal swings. The results show where product can safely be stored and where monitoring probes belong. Mapping is repeated after changes to racking, coils or controls. Paul Industries builds rooms with mapping in mind and supports it through qualification.

What does cold storage design need to settle before construction starts?

Before construction, cold storage design should settle the room schedule and temperatures, the racking and material handling plan, the refrigerant and system type, the defrost method, floor heating, sprinkler type, utility capacity and the controls platform. Changing any of these after steel and panels are ordered costs time and money. Paul Industries works through these decisions with the owner and the building designer during design-build preconstruction.

How often should cold storage refrigeration be maintained?

Cold storage refrigeration needs routine checks of compressors, oil, condensers, defrost, detectors and relief valves on schedules set by the manufacturer and, for ammonia, by IIAR 6 inspection and testing tasks and the plant’s process safety program. Evaporative condensers need water treatment and cleaning through the season. Paul Industries provides scheduled maintenance, keeps the records the PSM or general duty program needs, and handles repairs when something fails.

Why does ice build up around freezer doors and penetrations?

Ice forms where warm, moist air reaches a cold surface, so it collects at doors, dock seals, unsealed pipe and conduit penetrations, and damaged vapor retarders. It is a symptom of air and moisture leaking into the freezer, which adds load to the refrigeration plant and creates slip hazards. Paul Industries seals and insulates penetrations, repairs vapor barriers and adds heated door frames, air curtains or dehumidification at the dock.

What records come with a new cold storage refrigeration plant?

A new plant should arrive with equipment data, the P&ID and flow diagrams, piping test records, relief valve data and calculations, control narratives and setpoints, startup reports, and operating and maintenance manuals. Ammonia systems add process safety information, valve tagging and labeling under IIAR guidance, and inputs to the hazard analysis. Paul Industries assembles that package at turnover so the operator’s safety and maintenance programs start complete.

Planning a cold storage build, expansion or retrofit?

Send the room schedule and temperatures, the building size and site location, the refrigerant you are considering and your target dates. Call 201-450-8280 or request a quote.