Hot tapping is a method of making a new branch connection on a pipe while it stays full and under pressure: a fitting and valve are attached to the live line, a cutter passes through the open valve inside a sealed housing, and the cut-out piece of wall is withdrawn before the valve closes. Paul Industries performs hot tapping and line stopping on water, chilled water, steam, condensate, fire, gas, compressed air and process lines, so a plant, hospital or data center adds a branch or a valve with its system still running.
Request a quote or call 201-450-8280
From its headquarters at 256 Shore Drive in Kilmarnock, Virginia, Paul Industries takes hot tap and line stop work across the United States and at international sites. Typical requests are a new chilled water branch for an added data hall, a steam connection for a new process user, an isolation valve on a main that has none, and a water service for an expansion that cannot wait for the next annual shutdown.
What is hot tapping in piping, and how does hot tapping work?
Hot tapping in piping is defined by OSHA as welding on pipelines, vessels or tanks under pressure to install connections or appurtenances, commonly to add or replace sections of pipeline without interrupting service to air, gas, water, steam and petrochemical systems. In practice the term also covers bolted mechanical sleeves that need no welding at all.
How does hot tapping work mechanically? A branch fitting is welded or clamped to the run pipe, and a full-bore valve is bolted to the fitting. The hot tapping machine bolts to the open valve, with its cutter and a pilot drill housed in a pressure-tight chamber. The pilot drill pierces the wall first and holds the coupon, the hole saw cuts the full opening, and the boring bar retracts the cutter and coupon back through the valve. With the valve closed, the machine comes off, and the new branch is ready to pipe.
For a facility manager the short answer is simpler: a hot tap is the way to connect to a pipe that has to stay full. Paul Industries uses it when a shutdown would stop production, interrupt patient care, take a data hall off cooling or require draining and refilling a large loop with treated water.
The hot tapping process, step by step
The hot tapping process follows a written procedure with hold points, because each step depends on what was confirmed before it. Paul Industries prepares that hot tapping procedure for each tap and reviews it with the owner’s operations and safety staff before any work starts on the line.
| Step | What happens | Hold point or check |
|---|---|---|
| 1. Line survey | Contents, pressure, temperature, flow, pipe material and location confirmed against drawings and field readings | Owner signs the line data sheet |
| 2. Wall check | Ultrasonic thickness readings in a grid around the tap location | Minimum wall meets the procedure; laminations and corrosion absent |
| 3. Fitting attachment | Weld-on nozzle or split tee welded with a qualified in-service procedure, or a mechanical sleeve bolted on | Visual and surface examination of welds |
| 4. Valve installation | Full-bore gate or ball valve bolted to the fitting flange | Valve bore checked against cutter diameter |
| 5. Pre-tap test | Fitting and valve pressure or leak tested before cutting | Test held at the procedure pressure without loss |
| 6. Cut | Machine mounted, valve opened, pilot and cutter advanced through the wall | Cut depth and cutter stroke recorded |
| 7. Retrieval | Cutter and coupon retracted, valve closed, machine bled down and removed | Coupon recovered and inspected |
| 8. Branch completion | New piping connected to the tapping valve, tested and placed in service | Branch test record and as-built markup |
The hot tapping operation on the line itself is a small part of the job. Survey, wall measurement, fitting work and testing take most of the effort, and they decide whether the cut goes cleanly. A hot tapping method chosen for the line, welded or mechanical, follows from the first two rows of that table.
Hot tapping fittings: split tees, weld-on nozzles and sleeves
Tap fittings carry the pressure load that the cut removes from the run pipe, so the fitting is chosen for branch size, pipe material and whether welding on the live line is acceptable. Paul Industries selects among four families, and the choice is fixed in the procedure before any material is ordered.
| Fitting | How it attaches | Typical use |
|---|---|---|
| Weld-on nozzle or reinforced branch fitting | Fillet or groove welded directly to the run pipe | Small and mid-size branches on steel steam, chilled water and process lines |
| Full-encirclement split tee | Two halves welded around the pipe with longitudinal seams, then end fillet welds | Large branches, including size-on-size taps, and line stop fittings |
| Bolted mechanical tapping sleeve | Clamped with gaskets, no welding on the live line | Ductile iron, cast iron, PVC and steel water mains |
| Hot tapping saddle | Strap or welded saddle over part of the circumference | Small service and instrument connections on water and air lines |
A hot tapping split tee spreads the load around the whole pipe, which is why owner specifications commonly call for one once the branch bore exceeds about half the header bore, and integrally reinforced weld-on fittings for smaller branches. A hot tapping tee for a line stop is built heavier still, because it must also hold the plugging head and the thrust of the stopped line. The hot tapping sleeve used on water mains is a gasketed shell bolted around the pipe, with a flanged outlet machined so the tapping valve aligns with the cutter.
The hot tapping valve is a full-port gate or ball valve whose bore passes the cutter, and it stays on the line as the branch isolation valve once the job is complete. Paul Industries checks the valve’s rating against line pressure and temperature, and its bore against the cutter size, before the procedure is issued.
Hot tapping welding on a line in service
Welding for a hot tap is ordinary pipe welding made harder by two opposing risks: too much heat can burn through a wall that is holding pressure, and too little heat lets the flowing contents quench the weld so fast that it hardens and cracks. The welding procedure balances those risks for the specific pipe, wall thickness, contents and flow rate.
Flow is the variable most people overlook. Water, chilled water and liquid process streams pull heat out of the pipe wall quickly, so welds made on a flowing liquid line cool much faster than the same weld on an empty pipe. Procedures for in-service welding, such as those qualified under Annex B of API 1104, record the contents and flow conditions they were qualified for, and a hot tap made outside that envelope needs a different procedure. Paul Industries qualifies its welding procedures and welders to ASME Section IX for plant piping, measures the wall before the first arc, and sets heat input, electrode type and bead sequence in the written procedure.
Contents also matter beyond cooling. Some fluids decompose, polymerize or ignite at the temperature a weld puts on the inside of the wall, and those lines are reviewed with the owner before a welded tap is approved. Where welding is unsuitable, a mechanical sleeve or a different connection point avoids it.
Hot tapping a water line or water main
Water service taps are the routine case: water is nonflammable, pressures are moderate, and bolted tapping sleeves fit most pipe materials, so a hot tapping water line job is usually the simplest tap a facility orders. A hot tapping water main connection for a building service, a fire line or a plant expansion is made with the main in service, so neighboring customers and the building’s own system keep their supply.
Water work follows waterworks standards. AWWA C223 covers fabricated steel and stainless steel tapping sleeves, and MSS SP-60 sets the flange joint between a tapping sleeve and its tapping valve so the two mate and the cutter runs true. The utility or owner usually specifies sleeve material, test pressure and disinfection, and AWWA C651 sets the disinfection, sampling and handling requirements that apply to new mains and repairs. Paul Industries cleans and disinfects the sleeve and valve interior before the cut, so nothing from the fitting enters the main.
Hot tapping water pipe inside a building or plant is often welded rather than bolted, because the pipe is steel or stainless and the branch is a domestic, process or fire connection. Paul matches the method to the pipe: a weld-on fitting on steel, a sleeve on ductile iron or cast iron, and a sleeve or fusion fitting rated for plastic pipe.
Hot tapping a pipe in a plant: chilled water, steam and process lines
Tapping a pipe inside an operating plant is where the method saves the most, because draining a large chilled water loop, a steam main or a process header takes days of downtime and refilling, treatment and restart. Industrial hot tapping lets the new branch be built and tested in advance, then connected with the system live.
Chilled water pipe hot tapping
Live chilled water taps are common in data centers, hospitals and campuses, where cooling has to run continuously and the loop holds tens of thousands of gallons of treated water. Paul Industries ties new air handlers, process coolers and data center cooling branches into live mains, often alongside the expansion of a chilled water system it is building. Insulation and vapor barrier are removed only at the tap and restored afterward.
Hot tapping steam lines
Steam taps bring higher temperature, higher pressure and condensate to manage. Wall thickness on older steam mains varies with corrosion and erosion, so the ultrasonic survey matters more here than anywhere. The branch takeoff is placed on top of the main so it draws dry steam, as on any steam piping branch, and a drip leg and trap are added where the new line needs them.
Process, air and gas service lines
Pipe hot tapping on process headers, compressed air mains and nitrogen distribution follows the plant’s own piping specification, usually ASME B31.3 process piping. Stainless lines need purge and filler control the same as any stainless weld, and plants with sanitary standards may require a different tie-in method for product contact service. Paul Industries reviews the specification with the owner and records the decision in the procedure.
Hot tapping a gas line and pipeline hot tapping
Gas taps follow stricter rules than water work because the contents are flammable, the cut opens a path to the atmosphere if anything fails, and gas utilities and pipeline operators impose their own procedures. API RP 2201, the recommended practice for safe hot tapping in the petroleum and petrochemical industries, is the usual reference inside refineries, terminals and chemical plants.
Pipeline hot tapping on larger transmission and gathering lines adds in-service welding procedures qualified for the line’s contents and flow, plus operator approval and inspection at each hold point. Hot tapping pipeline connections inside a plant fence, such as a new fuel gas branch to a boiler or a process gas header, use the same discipline at smaller scale. Paul Industries handles hot tapping gas pipeline work inside plants and facilities, coordinated with the owner’s operations staff and the gas supplier where the tie-in is upstream of the plant’s meter, and it brings the same planning to oil and gas facilities.
What is line stopping?
Line stopping is the temporary plugging of a pressurized pipe from outside, so a section downstream can be isolated for work while the rest of the system stays in service. A line stop starts as a hot tap: a heavy split tee and valve are installed, the line is cut, and a plugging head is pushed into the pipe through the valve to seal it.
A single line stop isolates a dead-end section or the last length of a branch. Two line stops with a temporary bypass between them isolate a section in the middle of a main, which is how a failed valve is replaced, a new isolation valve is added, or a damaged length of pipe is cut out while flow continues around the work. When the job is complete, the heads retract, a completion plug or blind flange closes each fitting, and on many fittings the valve is recovered for reuse. The fittings stay on the pipe and can be used again for a future line stop.
Taps and line stops together let an owner do work that would otherwise need a full system shutdown. Paul Industries plans both as one sequence, sizes the bypass for the flow the line must keep, and builds the new valve or pipe section in advance so the isolated period is as short as the work allows.
| Method | How it works | Where it fits |
|---|---|---|
| Hot tap | Branch cut into a live, pressurized line through a fitting and valve | New branches and connections with the system running |
| Line stop | Plugging head inserted through a hot tap to block flow; bypass keeps service | Valve replacement, pipe repair or rerouting in a running main |
| Pipe freeze | Liquid nitrogen or refrigeration forms an ice plug inside the pipe | Short isolation on smaller water-filled lines with little or no flow |
| Cold tap | Branch cut into a drained, depressurized line | Work during planned shutdowns or on new piping |
| Shutdown and drain | System isolated at existing valves and drained | Large scopes during turnarounds where the whole system is offline |
What is hot tapping and cold tapping in practice? Cold tapping vs hot tapping comes down to whether the line can be emptied: cold taps are cheaper and simpler when a shutdown is already planned, and hot taps win when it is not. Hot tapping vs pipe freezing turns on size and flow, because an ice plug needs still water and grows impractical on large or flowing lines, while a hot tap or line stop is sized by the fitting and the machine.
Hot tapping safety precautions and approvals
Safety on a hot tap starts with deciding that a hot tap is the right method at all, then controlling the line contents, the weld, the fitting test and the cut through a written plan. OSHA’s lockout standard does not cover hot tap operations on pressurized gas, steam, water or petroleum systems where the employer shows that continuity of service is essential, that shutdown is impractical, and that documented procedures and special equipment give proven protection, so the procedure itself is the protection and must be followed exactly.
- A line data sheet confirms contents, pressure, temperature and flow, signed by the owner.
- Ultrasonic thickness readings confirm the wall at the fitting location.
- A hot work permit, fire watch and gas testing apply wherever welding is involved.
- The fitting and valve are pressure or leak tested before the cut.
- Cutter, pilot and coupon retention are checked before the machine is mounted.
- Escape routes, isolation points upstream and communication with operations are agreed before the valve opens.
Paul Industries writes these steps into each procedure and holds the job at each check until it is signed. Facilities with their own emergency repair plans can keep the tap procedure on file for later work on the same main.
Hot tapping applications in operating facilities
Applications range from small instrument connections to large branches for new buildings. Paul Industries uses the method for:
- Adding chilled water, heating water or steam branches for new equipment, floors or buildings.
- Installing isolation valves on mains that were built without them, using line stops and a bypass.
- Connecting temporary chillers or boilers during equipment replacement.
- Adding fire service or domestic water connections to a live main.
- Installing flow meters, sample points, pressure taps and chemical injection quills.
- Rerouting pipe around a new foundation or structure while the line stays in service.
Hospitals use the method heavily, since patient areas rarely tolerate a heating, cooling or water outage; Paul’s work for hospitals and healthcare facilities often begins with a hot tap so new construction can connect without disturbing occupied floors.
Who performs hot tapping and line stopping?
Paul Industries performs hot taps and line stops for manufacturing plants, hospitals, data centers, campuses and commercial buildings in all 50 states, from procedure and fitting selection through welding, testing, the cut and the branch piping that follows. As a hot tapping company that also builds the systems being tapped, Paul delivers the tie-in and the new piping under one contract.
Owners comparing hot tapping companies usually look at who writes the procedure, who qualifies the in-service welding, who tests the fitting and who completes the branch afterward. A hot tapping service that stops at the valve leaves the owner coordinating the next contractor, while Paul’s hot tapping services include the branch, its supports and insulation, and its test. The same welding qualifications Paul uses on industrial welding services apply to every welded fitting, and tie-ins that fit into a planned outage can be grouped with shutdown and turnaround work.
How much does hot tapping cost?
The price of a hot tap depends on branch and run size, pipe material and wall condition, line pressure and temperature, whether the fitting is welded or bolted, how many line stops and how much bypass piping the job needs, and the access and working hours the site allows. A small bolted tap on a water main is a modest job; a size-on-size line stop on a large chilled water main with a bypass is a project.
The fitting and valve are often the biggest material item on a big tap, and split tees for line stops are heavier and costlier than branch fittings. Labor is driven by preparation, welding and testing more than by the cut itself. Work limited to nights or weekends, confined or elevated locations, and extra examination required by the owner all add cost. Paul Industries gives a budget from comparable taps once it knows the line data and location, then a firm price after a site survey and thickness readings.
Hot tapping from Paul Industries
Paul Industries offers hot tap work through three routes: supply-only of fittings and valves selected to the line data, design-build where the tie-in is part of a larger system change, and complete installation from survey through the finished, tested branch. On every route the owner receives the procedure, line data sheet, thickness readings, welding records, test records and as-built markup.
Branch routing gets the same attention as the tap. New piping from the tapping valve is supported independently so its weight and thermal movement never load the fitting, insulated to match the main, labeled, and tested at its own design pressure before the valve opens to it. Paul Industries also marks the fitting location on the owner’s drawings so the next project knows where the connection sits.
Paul builds the branch and the equipment it feeds as part of the same scope, so a tie-in for a new chiller, boiler or process line connects to work already designed and tested. To plan a tap or line stop, call 201-450-8280 or request a quote with the line size, material, contents, pressure, temperature and a photo of the proposed location.
Standards referenced: OSHA 29 CFR 1910.147 (control of hazardous energy), hot tap definition and exemption · API RP 2201 Safe Hot Tapping Practices in the Petroleum and Petrochemical Industries · API 1104 Annex B, in-service welding · ASME B31.3 Process Piping · ASME B31.1 Power Piping · ASME Boiler and Pressure Vessel Code, Section IX · AWWA C223 Fabricated Steel and Stainless Steel Tapping Sleeves · AWWA C651 Disinfecting Water Mains · MSS SP-60 Connecting Flange Joint Between Tapping Sleeves and Tapping Valves
Frequently asked questions
Is hot tapping dangerous?
A hot tap carries real hazards, including burn-through during welding, release of contents if a fitting or valve fails, and cracking of a weld cooled too fast by flow. Those hazards are controlled by a written procedure, measured wall thickness, qualified in-service welding, a pre-tap test of the fitting and valve, and hold points that stop the job until each check is signed. Paul Industries follows that procedure on every tap.
What size branch can be hot tapped?
Branches range from small instrument connections to size-on-size taps, where the branch matches the run pipe diameter. Large and size-on-size taps use full-encirclement split tees that carry the load around the whole pipe. Paul Industries sizes the fitting, valve and cutter for the branch the owner needs and confirms the run pipe wall can carry the fitting.
What pressure and temperature can a hot tap be made at?
The limits come from the fitting and valve rating, the run pipe wall thickness and material, the contents and the tapping machine rating, so they are set for each tap in its procedure. Water and chilled water taps are routine at normal system pressures, while steam and gas taps get additional review of heat input and contents. Paul Industries records the line conditions on the data sheet and checks every component against them.
How long does a hot tap take?
Most of the time goes into survey, thickness readings, fitting attachment and the pre-tap test, and the cut itself is short by comparison. A bolted tap on a water main is often one visit; a welded tap with examination and testing, or a line stop with a bypass, spans several work periods. Paul Industries schedules each phase with the owner so the line stays in service throughout.
Can a hot tap be made on plastic pipe?
Plastic water mains in PVC are tapped with mechanical sleeves rated for the pipe, and polyethylene lines use fusion fittings designed for tapping. The fitting must match the pipe material and pressure class, and the cutter is chosen for plastic. Paul Industries confirms the pipe material and dimensions in the field before ordering the fitting.
Can stainless steel process pipe be hot tapped?
Stainless process pipe can be hot tapped with a welding procedure qualified for stainless, controlled heat input and attention to the inside surface the weld will affect. Plants with sanitary or high-purity standards often prefer a different tie-in for product contact lines. Paul Industries reviews the service with the owner and documents the chosen method.
What is a line stop used for?
A line stop isolates a section of a pressurized pipe so a valve can be replaced or added, a damaged section repaired, or the pipe rerouted while the rest of the system runs. Two line stops with a temporary bypass keep flow moving around the work. Paul Industries plans the stops, the bypass and the new section as one sequence.
How is the coupon kept from falling into the line?
The pilot drill pierces the wall before the main cutter and carries retaining wires or a similar catch that holds the coupon as the cutter finishes. The coupon is withdrawn through the valve with the cutter and recovered before the machine is removed. Paul Industries checks the retention device before mounting the machine and logs the recovered coupon.
Does hot tapping need a hot work permit?
Any welded tap needs a hot work permit under the facility’s fire prevention program, along with gas testing where flammables may be present and a fire watch during and after welding. Mechanical sleeves avoid welding, though the owner’s permit system still governs work on the live line. Paul Industries works within the site permit system on every job.
Can a fire protection main be hot tapped?
Fire mains are hot tapped regularly to add a building service, standpipe or sprinkler connection without taking the main out of service. The work is coordinated with the authority having jurisdiction and the owner’s insurer, and the new connection is tested before it is accepted. Paul Industries plans the tap so any impairment of fire protection is avoided or kept as short as possible.
What records come with a hot tap?
A complete record includes the line data sheet, ultrasonic thickness readings, welding procedure and welder qualifications, weld examination results, the pre-tap test record, the cut log and the branch test record. Paul Industries assembles these into one package so the owner can show how the connection was made.
What information is needed to plan a hot tap?
Planning needs the pipe size, material and schedule, the contents, operating pressure and temperature, flow conditions, the branch size wanted, and the location with access and clearance. Drawings and photographs shorten the survey. Paul Industries confirms the data in the field and adds thickness readings before it issues the procedure.
Does the tapping valve stay on the pipe?
On a branch tap the tapping valve normally remains as the isolation valve for the new branch. On line stop fittings, a completion plug seals the fitting so the valve can be removed and reused, and a blind flange closes the outlet. Paul Industries specifies which arrangement suits the job before ordering the fitting.
Who approves a hot tapping procedure?
The owner’s operations, engineering and safety staff approve the procedure, and gas utilities, pipeline operators and water authorities add their own approval where the tie-in touches their system. Paul Industries writes the procedure, presents it for review and holds the work until every signature is in place.
Who provides hot tapping for hospitals and data centers?
Paul Industries provides hot tapping and line stopping for hospitals, data centers and campuses, where heating, cooling and water must stay on. The work includes the procedure, fitting, welding, test, cut and the new branch piping, delivered under one contract and coordinated with facility operations.
What makes a line stop cost more than a branch tap?
A line stop needs a heavier split tee rated to hold the plugging head and line thrust, the plugging equipment itself, and often a second stop and a bypass with its own taps and piping. The isolated work, such as a new valve or pipe section, adds to that. Paul Industries prices the stops, bypass and replacement work separately so the owner can see each part.
Can a hot tap be made close to a weld or fitting?
Tap locations are kept clear of existing welds, fittings and supports so the new fitting sits on sound, uniform pipe and the cutter has room to work. The procedure sets the clearance for the fitting chosen. Paul Industries picks the location during the survey and confirms it with thickness readings before welding.
Need a branch or a valve on a line that has to stay live?
Send the line size, material, contents, pressure and a photo of the location. Call 201-450-8280 or request a quote.
