Paul Industries is a process equipment contractor in North Dakota that designs, fabricates, installs, tests and starts up process piping, steam and boiler systems, pressure vessels, tanks, heat exchangers and water treatment for oilseed crush plants, ethanol and renewable fuel plants, refineries, gas processing, sugar and durum mills and the new data center campuses. North Dakota pairs the third-largest crude output among the states with a farm economy that processes beets, durum, soybeans and corn on a large scale, and every one of those plants depends on pressure equipment that has to run through a prairie winter. Paul Industries carries a North Dakota project from engineering through startup under one contract, or supplies the equipment alone.

Request a quote or call 201-450-8280

Headquarters 256 Shore Drive, Kilmarnock, Virginia
Crude oil About 1.16 million barrels a day in 2025, third among states
Ethanol Six plants, about 550 million gallons a year
Boiler law NDCC 23.1-16, inspected under the DEQ Boiler Inspection Program
Industrial power 7.25 cents/kWh, against 8.13 nationally (EIA, 2024)
Reviewed November 2026

What does a process equipment contractor in North Dakota build?

A process equipment contractor in North Dakota builds the systems that move, heat, cool, separate and clean liquids and gases inside a plant: process and utility piping, steam and condensate systems, boilers and their feedwater trains, pressure vessels, process tanks, heat exchangers, pump skids, cooling and refrigeration, and the water treatment that feeds all of them. The equipment list looks similar from state to state, but the North Dakota version is shaped by three things: very cold winters, plants that run long continuous campaigns with short outage windows, and a fuel and feedstock base drawn from oil, natural gas, lignite and grain.

Paul Industries designs, fabricates, supplies, installs, tests, starts up, services, repairs and maintains that equipment. Owners choose the route that fits the job: supply-only skids, spools and vessels delivered to site; a design-build package where Paul Industries carries both the engineering and the installation; or complete installation of a design the plant’s own engineer has prepared. Each route ends with the same turnover records: drawings, material certificates, weld and test records, and startup data.

Which North Dakota industries run process systems?

North Dakota industries that run process systems fall into five groups: oil and gas production and refining, coal gasification and power, biofuels, agricultural processing, and a fast-growing set of data center campuses. Ask what is the main industry in North Dakota and most answers start with oil and farming, and both feed directly into North Dakota manufacturing: fuels, fertilizer and gases at Beulah, sugar along the Red River, pasta and flour from durum, vegetable oil and meal from soybeans, and ethanol from corn.

North Dakota process industries, where they operate and the systems they rely on
IndustryWhere in North DakotaProcess systems insidePaul Industries scope
Oil, gas and refiningBakken counties around Williston, Watford City and Tioga; Mandan; DickinsonGas processing trains, compression, crude and product tankage, refinery units, renewable diesel pretreatmentASME B31.3 piping, vessels, exchangers, tank piping, turnaround scope
Coal gasification and powerBeulah and the lignite region of Mercer CountyGasifiers, gas cleanup, ammonia and fertilizer units, cooling water, steamSteam and condensate piping, exchanger repair, water treatment, pump skids
Ethanol and oilseed crushRichardton, Underwood, Hankinson, Spiritwood, CasseltonFermentation, distillation, evaporators, solvent extraction, oil refiningProcess piping, CIP, steam, cooling, corrosion and passivation work
Sugar, durum and foodRed River Valley at Hillsboro and Drayton; Carrington, Minot, Grand ForksDiffusers, evaporators, crystallizers, mills, hygienic process linesSanitary piping, heat exchangers, steam, effluent and process water
Data centersEllendale, Jamestown and the Harwood area north of FargoChilled water plants, liquid cooling loops, heat rejection, water treatmentChilled water piping, cooling systems, closed loops, commissioning

The Mandan refinery and the Dickinson, North Dakota refinery

North Dakota refinery capacity is concentrated at Mandan, where Marathon Petroleum lists crude capacity of 72,000 barrels per calendar day, while the Dickinson, North Dakota refinery completed its conversion to renewable diesel in 2021. Both sit on a crude and gas field that produced about 1.16 million barrels of oil a day through much of 2025 and, by the state’s April 2026 count, about 3.5 billion cubic feet of natural gas a day. That gas has to be gathered, compressed, treated and processed before it can be sold, so gas plants, compressor stations and the tank batteries that feed them are a steady source of process piping, vessel and exchanger work.

Refining and renewable diesel plants share a pattern: long runs between turnarounds, then a compressed outage in which exchanger bundles are pulled, piping is replaced and vessels are opened for inspection. Paul Industries fabricates replacement spools and vessels before the outage starts, plans the piping and exchanger scope of shutdowns and turnarounds, and documents each weld and test for the plant’s inspection program.

Great Plains Synfuels at Beulah

The Great Plains Synfuels Plant near Beulah, run by Basin Electric’s Dakota Gasification Company since 1984, is described by the U.S. Department of Energy as the one commercial plant in the United States that turns coal into synthetic natural gas. Lignite goes in; pipeline gas, anhydrous ammonia, ammonium sulfate, phenol, cresylic acid and other products come out, and captured carbon dioxide is shipped by pipeline to Canada. A complex like that is a dense mix of high-temperature gas service, corrosive condensates, cryogenic and refrigeration duty and large cooling water systems, which is why the lignite region around it buys exchanger, piping and water treatment work every year.

North Dakota ethanol plants and soybean crush

North Dakota ethanol plants number six, with combined capacity of about 550 million gallons a year by the state producers’ association count, and more is coming: Gevo has announced an expansion of its Richardton plant to 75 million gallons a year, and a 240 million gallon plant is being developed near Glen Ullin for operation in 2029. Ethanol plants run fermentation, distillation and evaporation around the clock, and their cook, beer and stillage systems wear out pumps, exchangers and piping in a predictable cycle. The crush plants at Spiritwood and Casselton add solvent extraction to the same map. Paul Industries has dedicated pages for that work: solvent extraction and crush plant piping and solvent plant shutdown and turnaround work.

Sugar beets, durum and the Red River Valley

Sugar is a major food process in the eastern half of the state. American Crystal Sugar runs factories at Hillsboro and Drayton in the Red River Valley, and a study for the cooperative puts Minnesota and North Dakota together at more than half of all U.S. beet sugar. A North Dakota sugar factory runs a campaign of slicing, diffusion, juice purification, evaporation and crystallization that lasts most of the winter, which puts enormous load on steam, condensate and process water systems in the coldest months. Durum is the other signature crop: North Dakota grows about half of the U.S. durum crop, milled into semolina and pasta at Carrington, Minot and Grand Forks. Mills and pasta lines need hygienic process water, dryer steam and dust control, the kind of work described on the dust control and hazardous area page.

Data center campuses at Ellendale and Harwood

Data center construction has become a large buyer of cooling equipment in the state. Applied Digital’s Polaris Forge 1 campus at Ellendale is contracted to reach 400 megawatts of critical IT load at full build, and a second campus of 280 megawatts is planned near Harwood, north of Fargo. Buildings that size need chilled water plants, liquid cooling distribution, heat rejection and treated make-up water. Paul Industries builds data center cooling systems from the chiller plant to the rack-level loop, and a cold climate gives those designs long hours of free cooling when the economizer side is laid out for it.

Process systems Paul Industries designs and installs across North Dakota

Process systems Paul Industries designs and installs across North Dakota range from a single replacement exchanger to a complete plant utility package, and North Dakota manufacturing companies use the same contract to buy design, fabrication, installation and startup. The table below links each system to the page that explains it in depth.

Systems Paul Industries delivers in North Dakota and the plants that use them
SystemTypical North Dakota plantsWhat Paul Industries delivers
Process pipingGas plants, refineries, ethanol, crushProcess piping to ASME B31.3, prefabricated and pressure tested before delivery
Steam and boiler plantSugar factories, ethanol, crush, hospitalsSteam, condensate and feedwater systems, plus boiler repair and retubing
Steam, condensate and coolingCrush and solvent plantsSteam, condensate and cooling systems for crush plants
Pressure vessels and tanksGas processing, fertilizer, renewable dieselPressure vessel fabrication to ASME Section VIII with data reports
Heat exchangersRefineries, evaporators, gasificationHeat exchanger repair, retubing and replacement bundles
Corrosion controlOil refining, oilseed refining, ethanolRefining corrosion assessment and passivation
Freeze protectionTank farms, loading racks, outdoor headersHeat tracing and insulation designed for the coldest nights
Water treatmentBoiler feed, cooling towers, process waterIndustrial water treatment from softening to reverse osmosis

Manufacturing in North Dakota also includes equipment builders, food processors and hospitals that buy the same utilities on a smaller scale: a new boiler, a glycol loop, a softener and reverse osmosis train, or a sanitary transfer line. North Dakota industry tends to expand in steps tied to commodity cycles, so Paul Industries sizes headers, steam capacity and water treatment for the next expansion as well as the current one, and leaves tie-in points where the next phase will connect.

Skid-mounted equipment suits North Dakota well. A pump skid, chemical feed package, heat exchanger module or filtration train can be assembled, wired, hydrotested and function checked before it ships, then set on its foundation and connected with a handful of field welds or flanges. That approach cuts the number of hours spent working outdoors in the cold, keeps hot work out of classified areas, and lets the plant inspect the equipment at the fabrication stage instead of after it is installed.

North Dakota boiler inspection, code and building rules

North Dakota boiler inspection is set by chapter 23.1-16 of the North Dakota Century Code, a law first passed in 1953 and now administered by the Boiler Inspection Program of the Department of Environmental Quality in Bismarck. The North Dakota boiler inspection program covers both boilers and pressure vessels for construction: new equipment is built to the ASME Boiler and Pressure Vessel Code (the department lists the 2025 edition), the Manufacturer’s Data Report is filed with the department before installation, and National Board registration is required for boilers and pressure vessels alike. Power piping within the scope of ASME Section I follows ASME B31.1, and welded repairs and alterations are made under the National Board R program or an equivalent state authorization, with the inspector involved before the work starts.

North Dakota boiler and pressure vessel inspection intervals (National Board synopsis, reviewed by the state in November 2025)
EquipmentInternal inspectionExternal inspectionWhat it means for the plant
High-pressure (power) boilersEvery yearEvery year, under pressurePlan the internal around the plant outage so the boiler opens once
Low-pressure steam boilers, steelEvery 2 yearsEvery 2 yearsBuilding and process heat boilers on a two-year cycle
Low-pressure steam boilers, cast ironNone setEvery yearAnnual external check of controls and safety devices
Hot water heating and supply boilersNone setEvery 3 years; yearly in hospitals, nursing homes and schoolsHealthcare and school plants run on the shorter interval
Pressure vesselsBuilt and registered to ASME Section VIII; field inspection required for anhydrous ammonia vesselsData reports and nameplates must match before startup

Inspections by inspectors of authorized inspection agencies and by owner-user inspection organizations, each commissioned by the department, are accepted in place of a state inspection, and the report goes to the department within 15 days. A North Dakota boiler inspector then issues the certificate of inspection, which carries a $35 yearly fee paid by the owner. Paul Industries assembles the documents those inspections ask for on new and repaired equipment: data reports, registration numbers, relief valve settings and the test record.

Buildings and their mechanical systems follow the North Dakota State Building Code, set up under NDCC chapter 54-21.3 and based on the International Building Code and International Mechanical Code, which cities, counties and townships that enforce it may amend. Process piping follows ASME B31.3, sanitary food and pharmaceutical lines follow ASME BPE, solvent extraction plants follow NFPA 36, and grain and flour handling follows NFPA 61 and NFPA 652 for combustible dust.

Designing process equipment for a North Dakota winter

Designing process equipment for a North Dakota winter starts with the normals: Bismarck’s average January low is about 2 degrees Fahrenheit and Fargo’s is near zero, with colder stretches every year and wind that strips heat from anything left bare. Any line that holds water, condensate, stillage, brine or a viscous product is a freeze risk once flow stops, and a frozen line in a sugar or ethanol plant mid-campaign stops production.

Paul Industries builds freeze protection into the layout rather than adding it after the first failure. Outdoor runs slope to low-point drains, dead legs are removed or traced, instrument impulse lines are traced and boxed, and steam tracing or electric tracing is chosen by the circuit, with insulation thickness set for the wind and the design low. Pump skids and valve stations that must stay outdoors get heated enclosures, and tank nozzles get tracing that reaches the shell. Wherever possible, spools and skids are welded, tested and painted off site and set during a planned window, so the hot work and hydrotesting inside the plant fit the frost-free months.

The same climate has an upside. Long cold seasons mean many hours in which cooling towers, dry coolers and economizers can carry chilled water and process cooling loads with the compressors off, which matters at data center campuses and at any plant with year-round cooling. Paul Industries designs those systems to switch between modes without freezing the tower basin or the coil.

Working inside a running North Dakota plant

Working inside a running North Dakota plant means fitting construction around a process that rarely stops: ethanol plants ferment and distill around the clock, crush plants and gas plants run long stretches between shutdowns, and sugar factories slice beets through most of the winter before a single intercampaign break. The contractor’s job is to make the time inside the plant as short and as safe as possible.

Paul Industries plans each job around the hazards of the specific process. Gas plants and gathering sites carry hydrogen sulfide and flammable gas, so isolation, gas testing and hot work permits are planned before any line is opened. Ethanol and solvent extraction areas are classified for flammable vapor, which sets where welding can happen and which work has to be done off site. Ammonia, fertilizer and refrigeration systems need their own isolation and purge procedures, and grain, flour and meal handling areas need dust control during cutting and grinding. Each job package lists the permits, isolation points, purge and test steps, and the order in which systems return to service.

Records matter as much as the welds. Refineries and gas plants inspect piping and vessels to API codes over their whole service life, food plants answer to their sanitation and audit programs, and boiler owners face the state inspector every one to three years. Paul Industries hands over weld maps, material test reports, pressure test records, data reports and as-built drawings in a form the plant’s inspection and maintenance staff can use for the next twenty years.

How a North Dakota project runs from first call to startup

A North Dakota project with Paul Industries runs in five stages, and the plant has one point of contact through all of them.

  1. Scope. The plant sends drawings, P&IDs, equipment data, photos and the outage dates. Paul Industries walks the site, confirms tie-in points and lists what the code and the insurer will ask for.
  2. Engineering. Piping is routed and stress checked, vessels and exchangers are specified to the governing code, and the design is set for freeze protection and the plant’s expansion plans.
  3. Fabrication. Spools, skids, vessels and supports are built and pressure tested off site, with weld maps, material certificates and data reports ready before delivery.
  4. Installation. Equipment is set and tied in during the agreed window, with permits for hot work, lockout and confined space handled inside the plant’s own system.
  5. Startup and turnover. Systems are flushed, tested, commissioned and handed over with as-built drawings, test records and a winterization and restart checklist.

What does process work in North Dakota cost?

Process work in North Dakota costs whatever the scope, the material, the code class and the outage window demand, and Paul Industries prices it from the plant’s own drawings rather than from a generic rate. The main cost drivers are pipe size and material (carbon steel against stainless or alloy), the code class and examination level, the amount of work that can be prefabricated, whether tie-ins have to be made during a short campaign break, and the freeze protection and insulation the location requires. Smaller items are fixed by the state: the $35 yearly boiler certificate fee, for example. Industrial electricity averaged 7.25 cents per kilowatt-hour in North Dakota in 2024 against 8.13 nationally, which shapes the payback on efficient pumps, condensate recovery and heat recovery. Paul Industries gives a budget range from comparable scope at the start and a firm price once the scope is defined.

Who builds process systems in North Dakota?

Paul Industries builds process systems in North Dakota: process and utility piping, steam and boiler plants, pressure vessels, process tanks, heat exchangers, cooling and water treatment for refineries, gas plants, the Beulah gasification complex, ethanol and crush plants, sugar factories, mills and data centers. Plant engineers who search for mechanical contractors in North Dakota usually need someone who can take a process system from design through startup, and that is the work Paul Industries does under one contract, with one schedule and one set of records.

An East Coast contractor working across all 50 states

Paul Industries is an East Coast contractor headquartered at 256 Shore Drive, Kilmarnock, Virginia, and it takes work across North Dakota, in all 50 states and at plants outside the United States. North Dakota plants get the same engineering, fabrication and documentation standard as a pharmaceutical plant in New Jersey or a data center in Virginia, applied to Bakken gas, lignite, beets, durum and corn. The neighboring hubs for South Dakota and Montana cover the plants across those borders.

Start a North Dakota project with Paul Industries

Paul Industries designs, fabricates, installs, tests, starts up and maintains process equipment for North Dakota plants, from one exchanger bundle to a complete utility system. Send drawings, equipment data, photos and the outage window, call 201-450-8280, or request a quote to start a North Dakota project.

Standards referenced: NDCC chapter 23.1-16 (Boiler Inspection) · North Dakota State Building Code (NDCC chapter 54-21.3) · ASME Boiler and Pressure Vessel Code · National Board Inspection Code · ASME B31.1 · ASME B31.3 · ASME BPE · NFPA 36 · NFPA 61 · NFPA 652

Frequently asked questions

What is North Dakota known for manufacturing?

North Dakota is known for manufacturing fuels, fertilizer and gases from oil, natural gas and lignite, along with sugar, semolina and pasta, vegetable oil and meal, ethanol and farm machinery. Many of those products come out of process plants that rely on steam, pressure vessels, heat exchangers and process piping. Paul Industries designs, fabricates and installs that equipment for North Dakota plants and maintains it once it is running.

What products are manufactured in North Dakota process plants?

Process plants in North Dakota make synthetic natural gas, anhydrous ammonia, ammonium sulfate and phenol at Beulah, gasoline and diesel at Mandan, renewable diesel at Dickinson, ethanol and distillers grains at six ethanol plants, soybean oil and meal at Spiritwood and Casselton, beet sugar in the Red River Valley, and semolina and pasta from durum. Paul Industries builds and services the piping, steam, vessels and water systems those plants run on.

How many ethanol plants are in North Dakota?

North Dakota has six ethanol plants with combined capacity of about 550 million gallons a year, by the count of the state producers’ association. Expansion is under way: Gevo has announced a larger Richardton plant at 75 million gallons a year, and a 240 million gallon plant near Glen Ullin is targeted for 2029. Paul Industries supplies and installs process piping, steam, cooling and corrosion work for ethanol plants in the state.

What does the North Dakota boiler code require for a new boiler?

The North Dakota boiler code requires a new boiler to be built to the ASME Boiler and Pressure Vessel Code edition the Department of Environmental Quality adopts, to carry National Board registration, and to have its Manufacturer’s Data Report filed with the department before installation. Power piping inside the Section I boundary follows ASME B31.1. Paul Industries assembles that paperwork with the equipment so the first inspection can proceed on schedule.

How often are boilers inspected in North Dakota?

High-pressure boilers in North Dakota receive an internal and an external inspection every year. Steel low-pressure steam boilers are inspected every two years, cast iron low-pressure boilers get a yearly external, and hot water heating and supply boilers get an external every three years, or every year in hospitals, nursing homes and schools. Paul Industries schedules repairs and upgrades so they line up with those inspection dates.

Are pressure vessels inspected in North Dakota?

Pressure vessels in North Dakota must be built to ASME Section VIII and registered with the National Board before they go into service, and the state requires field inspection for anhydrous ammonia vessels. Plants with insurers or owner-user inspection programs often inspect other vessels on their own schedule as well. Paul Industries fabricates vessels with data reports and nameplates complete and repairs vessels in service under the National Board Inspection Code.

Who inspects boilers for a North Dakota plant?

Boilers at a North Dakota plant are inspected either by the Department of Environmental Quality’s Boiler Inspection Program or by an inspector of an authorized inspection agency or owner-user organization holding a commission from the department. Reports are filed with the department within 15 days, and the owner pays a $35 yearly certificate fee. Paul Industries prepares the equipment, records and access those inspections need.

Who builds process piping for Bakken gas plants around Williston and Watford City?

Paul Industries builds process piping for gas processing and compression sites in the Bakken counties around Williston, Watford City and Tioga. Piping for those plants follows ASME B31.3, handles sour gas, natural gas liquids and produced water, and has to survive cold winters outdoors. Paul Industries prefabricates and pressure tests the spools, installs them during the plant’s window, and documents every weld.

Does Paul Industries work on refinery projects in Mandan and Dickinson?

Paul Industries takes refinery and renewable diesel work in Mandan and Dickinson: replacement process piping, heat exchanger repair and replacement bundles, pressure vessels, tank piping and the piping scope of planned turnarounds. Spools and vessels are fabricated before the outage so the work inside the unit fits the window, and the records are prepared for the refinery’s inspection program. Call 201-450-8280 to discuss a scope.

Who services steam and evaporator systems at Red River Valley sugar factories near Hillsboro and Drayton?

Paul Industries services steam, condensate, evaporator and process water systems for sugar factories in the Red River Valley, including the area around Hillsboro, Drayton and Grand Forks. Campaign work is planned between seasons, with replacement piping and exchanger work prepared off site and installed during the intercampaign window. Paul Industries also handles effluent and water treatment upgrades for those plants.

Does Paul Industries build cooling systems for data centers in Ellendale, Jamestown and the Fargo area?

Paul Industries builds data center cooling systems for campuses in Ellendale, Jamestown and the Fargo area: chilled water plants, liquid cooling distribution, cooling towers and dry coolers, closed loops and the water treatment that protects them. North Dakota’s cold seasons allow long hours of economizer cooling, and Paul Industries designs the plant to use them while keeping coils and tower basins safe from freezing.

What process work does Paul Industries do in Bismarck and Minot?

In Bismarck, Mandan and Minot, Paul Industries delivers process piping, boiler and steam work, heat exchangers, pressure vessels and water treatment for refineries, mills, food plants, hospitals and public utilities. Work ranges from single equipment replacements to complete utility systems, delivered as supply-only, design-build or complete installation. Send drawings and photos or call 201-450-8280 to start.

How does Paul Industries keep outdoor equipment from freezing in North Dakota?

Paul Industries keeps outdoor equipment from freezing by sloping lines to drains, removing dead legs, tracing and insulating every circuit that holds liquid, boxing instrument lines, and enclosing skids and valve stations that must stay outdoors. Tracing is sized from the design low and the wind, and the turnover package includes a winterization checklist with drain points and isolation valves for each system.

How long does a process project take in North Dakota?

A North Dakota process project runs from a few weeks for a replacement exchanger or boiler repair to many months for a new utility plant or process unit. The schedule is usually set by engineering, equipment lead times and the plant’s outage or campaign break. Paul Industries shortens the time inside the plant by fabricating and testing off site and planning outdoor work for the frost-free months.

What should a plant send Paul Industries for a North Dakota quote?

For a North Dakota quote, send drawings or P&IDs, equipment data sheets, photos of the area, the materials and code required, the operating pressures and temperatures, and the dates when the plant can shut down. Paul Industries returns a budget range from comparable scope and then a firm price once the scope is defined. Call 201-450-8280 or request a quote.

Does Paul Industries supply equipment only, or install it too?

Paul Industries does both. North Dakota plants can buy supply-only spools, skids, vessels and tanks delivered ready to set; a design-build package in which Paul Industries carries engineering and installation; or complete installation of a design the plant’s engineer has prepared. Every route includes the material, weld and test records the plant and its inspector need.

How do energy prices in North Dakota affect equipment choices?

Industrial electricity in North Dakota averaged 7.25 cents per kilowatt-hour in 2024, below the national 8.13, and natural gas is produced in the state. Lower energy prices lengthen the payback on some efficiency upgrades, but condensate recovery, heat recovery and variable-speed pumping still pay where loads run around the clock. Paul Industries calculates the payback for each option before recommending it.

Planning process or utility work at a North Dakota plant?

Send drawings, equipment data, photos and the outage dates for your North Dakota plant. Call 201-450-8280 or request a quote.