Paul Industries is a US process equipment contractor for Mexico that engineers and builds process skids, ASME pressure vessels, mix and storage tanks, piping spools and full process systems in US shops, tests them before shipment and delivers them to Mexican plants documented for NOM-020-STPS-2011, NOM-001-SEDE-2012 and COFEPRIS good manufacturing practices. Headquartered at 256 Shore Drive, Kilmarnock, Virginia, Paul Industries crates the equipment, moves it across the border under USMCA, and puts it into service at the plant, installing and commissioning it or directing the plant’s installation team. Weld records, calculation memos, Spanish procedures and validation protocols arrive in the same crates as the equipment.

Request a quote or call 201-450-8280

Headquarters 256 Shore Drive, Kilmarnock, Virginia
Pressure vessel rule NOM-020-STPS-2011, Categories I to III
Power 60 Hz; 127/220 V, with 440 V and 480 V three-phase
Documentation Operating and maintenance procedures in Spanish
Trade terms USMCA in force since July 1, 2020
Reviewed November 2026

What does a US process equipment contractor for Mexico build?

A US process equipment contractor for Mexico builds the same stainless and carbon steel equipment it builds for American plants, then adds the files, nameplates, voltages and Spanish documents that Mexican labor, energy and health rules require before that equipment goes into service. The difference is concentrated in paperwork and electrical design rather than in the welds, and getting it right in the US shop saves weeks at the destination.

Paul Industries designs and fabricates the full scope for Mexican sites: chemical feed and pump skids, pressure vessels and process tanks, process piping and sanitary spools, high-purity water systems for pharmaceutical and electronics plants, and industrial water treatment systems for boiler feed, cooling and process water. Larger orders combine these into complete process systems with one control panel and one turnover package.

Mexican plants pick the delivery route that fits their own engineering team. Supply-only covers design, fabrication, the factory acceptance test and delivery, with Paul directing the setting and tie-ins. Design-build adds process engineering and utility layout for the area the equipment serves. Complete installation sends Paul to the site to rig, pipe, wire, start and qualify the equipment, and the plant accepts a running system with its NOM file already assembled.

Where are Mexico’s process plants?

Mexico’s process plants cluster in four manufacturing regions, and each region’s industry mix decides which rules dominate a project: COFEPRIS for drug and device makers, NOM-020-STPS for every plant with steam or compressed gas, and the IMMEX program for exporters. The table summarizes the regions where most US-built process equipment for Mexico is installed.

Mexican manufacturing regions and the process equipment they use
RegionIndustries (market facts)Typical equipment scope
Mexico City, State of Mexico and TolucaThe center of Mexican drug manufacturing: INEGI counted 32% of medicine manufacturing facilities in Mexico City and 10% in the State of Mexico in 2023, and Mexico City holds half of the sites approved by the FDA or the EMAPurified water and WFI, clean steam, CIP and SIP, cleanroom utilities, sanitary piping
Guadalajara and JaliscoThe second pharmaceutical state (20% of medicine facilities) and the home of the Jalisco Electronics Manufacturing Cluster, which grew from Latin America’s first semiconductor plant, opened in 1968Ultrapure water, chemical distribution, process cooling, pharmaceutical water
Monterrey and Nuevo LeonThe largest industrial real estate market in Mexico, with automotive, appliance, metals and chemical plantsProcess piping, pressure vessels, boiler and steam systems, compressed air, wastewater
The Bajio: Queretaro, Guanajuato, Aguascalientes, San Luis PotosiAn automotive, aerospace and precision manufacturing corridor, with Queretaro anchoring aerospace, plus food and beverage plantsPaint and pretreatment water systems, process tanks, chillers and cooling loops, CIP

Drug makers around Mexico City and Toluca use the same pharmaceutical water and clean utility designs Paul builds for US plants, rewritten into Spanish and referenced to Mexican GMP. Device plants follow the medical device pattern, while semiconductor and electronics plants around Guadalajara need the ultrapure water and chemical systems described on the semiconductor page.

NOM-020-STPS-2011: Mexico pressure vessel requirements

NOM-020-STPS-2011 is the Mexican labor ministry’s standard for pressure vessels, cryogenic vessels and steam generators or boilers in the workplace, and it sets the Mexico pressure vessel requirements a plant must meet for every vessel it operates, whether that vessel was built in Monterrey or in the United States. The standard was published in the Diario Oficial de la Federacion on December 27, 2011, took effect on June 27, 2012, and remains in force.

The NOM 020 STPS rules fall on the employer, meaning the plant, rather than on the fabricator. The plant classifies every vessel and boiler into Category I, II or III, keeps an updated equipment list and a file for each item, runs review and maintenance programs for Category II and III equipment, and pressure tests or examines those categories by non-destructive methods. Operating, review and maintenance procedures must be written in Spanish. Category III equipment needs a control number from the STPS before it operates, requested through a single procedure since the STPS merged two former notices.

NOM-020-STPS-2011 categories for pressure vessels (by relief device calibration pressure)
CategoryNon-hazardous fluid (water, air)Hazardous fluidWhat the plant’s file holds
Category IUp to 490.33 kPa and up to 0.5 m3Falls in Category II or IIIName, serial or tag number, data sheet with design, operating and set pressures, volume and temperatures, maintenance records, location
Category IIUp to 490.33 kPa above 0.5 m3, or above 490.33 up to 784.53 kPa up to 1 m3Up to 686.47 kPa and up to 1 m3Adds year of manufacture, construction code, hydrostatic test pressure, test and weld repair records, drawing or manual, location sketch
Category IIIAbove 490.33 up to 784.53 kPa above 1 m3, or above 784.53 kPa at any volumeUp to 686.47 kPa above 1 m3, or above 686.47 kPa at any volumeAdds the STPS control number, a photo or rubbing of the nameplate, detailed drawings, a calculation memo signed by an engineer with a professional license number, and the conformity opinion

A US-built ASME vessel enters this scheme with most of the Category III file already in hand, because ASME construction produces the data report, the nameplate, the drawings and the test record. What Paul adds is the Mexican form of that file: the data sheet in kilopascals and cubic metres, a calculation memo in the format the standard describes, the Spanish operating and maintenance procedures, and a nameplate image ready for the plant’s records. Buyers often ask for a NOM 020 STPS 2011 English version to brief their US managers; Paul works from the official Spanish text published in the Diario Oficial and summarizes it in English for the buyer’s engineering team. A pressure vessel manufacturer in Mexico and a US fabricator face the same plant-side rules, so the comparison comes down to whether the file arrives complete.

Electrical design for Mexican plants: NOM-001-SEDE-2012 and 60 Hz supply

Mexico’s grid operates at 60 Hz, matching US supply, so motors and pumps keep their US speeds and curves, while voltages and the electrical installation standard differ. Building services commonly run at 127/220 V, and industrial three-phase supply appears at 440 V and 480 V, with 254/440 V and 277/480 V systems both in use, so the plant’s single-line diagram decides motor windings, transformers and control power.

NOM-001-SEDE-2012 is the electrical installations standard in force, published on November 29, 2012, and it governs conductor sizing, overcurrent protection, grounding and equipment installation at the plant. A replacement edition has been in preparation for several years, and Paul checks which edition applies at the time of design. Each skid panel is built for the site voltage, with Spanish nameplates, Spanish alarm text on the HMI and wiring diagrams that a Mexican electrical verifier can follow.

Units follow the plant. Most Mexican engineering teams work in SI units, with pressures in kilopascals or kilograms per square centimetre and pipe called out in either NPS or DN. Paul issues drawings in the units each plant maintains, with dual dimensions where its operators need both.

COFEPRIS rules for pharmaceutical and medical device equipment

COFEPRIS, Mexico’s federal health regulator, became a PIC/S participating authority on January 1, 2018, the 52nd authority to join, so drug plants in Mexico are inspected against national rules that align with the PIC/S GMP Guide. The governing standard for medicines is NOM-059-SSA1-2015, published on February 5, 2016. Medical device makers follow NOM-241-SSA1-2025, published on April 4, 2025 and in force since November 30, 2025, which replaced the 2021 edition.

For process equipment, these standards ask for what a US FDA inspector asks for, in Spanish: qualified water systems, cleanable and drainable product-contact surfaces, documented materials and finishes, calibrated instruments and executed IQ and OQ protocols. Paul writes user requirement specifications, test protocols and turnover documents in Spanish for COFEPRIS-regulated plants, keeps the English set for the buyer’s corporate quality group, and executes site acceptance testing and qualification at the plant.

How to export to Mexico: USMCA, IMMEX and the pedimento

How to export to Mexico, for a process skid, comes down to four documents and one decision: the USMCA certificate of origin, the commercial invoice and packing list, the Mexican import declaration called the pedimento, the Carta Porte for the domestic leg, and the decision on whether the plant imports under its IMMEX program. Paul prepares the US side and the supporting data for the Mexican side on every shipment.

What is a USMCA certificate of origin?

The USMCA, known in Mexico as the T-MEC, entered into force on July 1, 2020, and its origin rules let qualifying goods enter Mexico without the general import duty. A USMCA certificate of origin is the importer’s evidence for that preferential claim. USMCA certificate of origin requirements are set as a list of minimum data elements, including the certifier, exporter, producer and importer, the description and tariff classification of the goods, the origin criterion and the blanket period where one applies. No USMCA certificate of origin form is mandatory: any USMCA certificate of origin template works if it carries the required elements, and the certification may sit on the commercial invoice itself. Paul reviews the bill of materials for origin during design and issues the certification when the equipment qualifies.

What is a pedimento?

A pedimento is the Mexican customs entry declaration, filed electronically through the VUCEM single window by the importer’s agente aduanal, and every formal import of process equipment moves on one. The importer must be registered in the Padron de Importadores kept by the tax authority, the SAT. Once accepted and paid, the declaration carries a pedimento number that the plant keeps with the equipment’s fixed asset and NOM records. Value added tax of 16% applies at import unless a program such as IMMEX provides a credit. Paul supplies the invoice values, tariff descriptions, origin data and technical descriptions the agente aduanal needs, matched crate by crate to the packing list.

What is IMMEX, and how does the IMMEX program Mexico runs treat equipment?

IMMEX is the Mexican government’s program for manufacturing, maquila and export services, created by a 2006 decree that merged the earlier Maquila and PITEX programs. For a buyer of process equipment, the IMMEX meaning is practical: a plant holding an IMMEX program temporarily imports the machinery and equipment it uses to make export goods, and that equipment stays in Mexico for the life of the program. With the separate VAT and IEPS certification, the plant receives a tax credit for the VAT on those temporary imports; without it, the 16% VAT is paid at entry and recovered later. IMMEX program requirements include export commitments, inventory control of temporary imports and periodic reporting, so the equipment description, serial numbers and values on Paul’s invoice must match what the plant’s IMMEX system records. Maquiladora IMMEX plants in Monterrey and the Bajio, and IMMEX maquiladora operations in the northern border cities, buy equipment this way, and the IMMEX program Mexico applies treats a pump skid and a pressure vessel as fixed assets in that system.

In short, IMMEX program explained for an equipment buyer: confirm before ordering whether the equipment enters under the plant’s Mexico IMMEX authorization or as a definitive import, because the pedimento type, the tax cash flow and the paperwork differ. Paul sets the invoice and packing structure to match.

Export requirements for Mexico on a US-built process system
RequirementWhat it coversHow Paul handles it
US Electronic Export InformationRequired for exports over $2,500 per Schedule B number, and for items that need an export license at any valueExport classification of wetted materials during design; EEI filed before departure
USMCA certification of originMinimum data elements supporting duty-free entry for originating goodsOrigin review of the bill of materials; certification on or with the invoice
PedimentoMexican customs entry, filed through VUCEM by the agente aduanal for an importer registered with the SATInvoice, packing list, tariff descriptions and serial numbers matched crate by crate
IMMEX temporary importMachinery imported temporarily for the life of the plant’s program, with a VAT credit for companies holding VAT certificationAsset descriptions and values structured for the plant’s IMMEX inventory control
Carta PorteCFDI complement (version 3.1) that must accompany goods moving within MexicoWeights, dimensions and descriptions supplied for the Mexican carrier’s document
Road dimensionsNOM-012-SCT-2-2017 limits width to 2.60 m and height to 4.25 m without special authorizationSkids and modules sized for the legal envelope where the process allows

Shipping equipment to Mexico: Laredo, Gulf ports and Incoterms

Shipping equipment to Mexico from the US East Coast runs overland through Texas in most cases, because trucks carry most US-Mexico trade: 73.6% of it by value in 2025, according to the Bureau of Transportation Statistics. Laredo is the busiest crossing, ranked first among all US border ports with about $354 billion in trade in 2025, and its bridges handle the bulk of the freight bound for Monterrey, the Bajio and Mexico City. Trailers cross with a cross-border move, then continue on a Mexican carrier with the Carta Porte.

Oversized modules, columns and heavy vessels often go by sea instead, to the Gulf ports of Altamira and Veracruz. Container services link both ports with US Gulf and East Coast terminals; published routings show about ten and a half days between Savannah and Altamira with one transfer, with sailings every one to two weeks. Each sea shipment uses ISPM 15 crating, desiccant and vapor barrier, capped nozzles and marked lift points.

Importing equipment into Mexico works best under one of four Incoterms 2020 rules. Under FCA, the plant’s chosen carrier collects the crates at Paul’s dock. Under DAP, Paul carries freight and transit risk up to the named plant, with the importer clearing customs through its agente aduanal. CIF covers sea freight and minimum insurance to Altamira or Veracruz. DDP is less common for Mexico, because the importer of record has to be registered with the SAT; most Mexican plants keep that role and choose DAP or FCA. The international projects page explains the rules side by side.

How a Mexican project runs with Paul Industries

A Mexican project with Paul Industries follows nine stages, and the first two fix the NOM-020 category of each vessel, the electrical edition, the language of each document and the import route before fabrication starts. The table shows what the plant receives at each stage.

Project stages for a plant in Mexico
StageWhat happensWhat the plant receives
1. Scope and NOM reviewNOM-020 category of every vessel and boiler, NOM-001-SEDE edition, COFEPRIS standard, IMMEX or definitive import, IncotermCode basis in Spanish and English, category list
2. DesignP&IDs, calculations, electrical design for 220 V, 440 V or 480 V supply, module split checked against Mexican road limitsApproval drawings in SI or dual units
3. US shop fabricationWelding, assembly, piping, wiring and instrumentation with material traceabilityWeld maps, mill certificates, finish and passivation records
4. Factory acceptance testPressure test, functional and sequence tests, witnessed in person or by live videoSigned FAT protocol
5. NOM file and Spanish documentsData sheets, calculation memo, nameplate record, Spanish procedures and HMI textNOM-020 file per vessel, Spanish manuals
6. Crating and exportPreservation, crating, EEI, origin certification, data for the pedimento and Carta PorteCommercial invoice, packing list, certification of origin
7. Installation or supervisionPaul sets, connects and wires the system, or directs the plant’s team doing soInstallation and tie-in weld records
8. Start-up, commissioning, qualificationFlushing, loop checks, site acceptance test, IQ and OQExecuted protocols in Spanish and English
9. Handover and serviceOperator training in Spanish, turnover package, service visitsAs-built drawings, recommended spares, service plan

What determines the delivered cost for a Mexican plant?

The delivered cost of a project for a Mexican plant depends on five items besides the equipment, and Paul lists each separately in a US dollar quote so the plant’s purchasing team compares like with like.

  • NOM documentation. Category III vessels need fuller files, calculation memos and nameplate records than Category I items, and every procedure is translated into Spanish.
  • Electrical design. Panels for 440 V or 480 V supply with Spanish HMI text add design and programming hours over a standard US panel.
  • Freight route. Standard trucks through Laredo are the economical route; oversize permits under NOM-012-SCT-2-2017, escorts or a sea leg to Altamira add cost.
  • Duties and taxes under the Incoterm and import route. Originating goods under USMCA avoid the general import duty; VAT is paid or credited depending on IMMEX status and certification.
  • Installation route. Supervising the plant’s installers uses fewer Paul field days than complete installation, which leaves start-up risk with the builder.

Quotes start with a budget range from comparable scope and move to a firm price once the drawings, the plant and the Incoterm are settled.

Who builds process systems for plants in Mexico?

Paul Industries builds process systems for plants in Mexico, from single skids and vessels to complete water, CIP, piping and utility systems for pharmaceutical, medical device, electronics, automotive, food and chemical plants, and carries them through the factory acceptance test, the border and commissioning at the site. For a buyer who wants to export to Mexico from US shops without handing the paperwork to several firms, Paul brings the NOM file, the Spanish documents, the origin certification and the start-up under one contract. Paul builds for Canadian plants on the same USMCA framework, described on the Canada page.

Paul Industries for Mexican plants

From its headquarters at 256 Shore Drive, Kilmarnock, Virginia, Paul Industries engineers process systems for plants in Mexico City, Toluca, Guadalajara, Monterrey, the Bajio and the border states, builds the skids, piping spools, tanks, vessels and full systems in US shops, documents them for NOM-020-STPS-2011 and NOM-001-SEDE-2012, tests them in the shop and delivers them under USMCA. Paul then installs, starts up and commissions the equipment or supervises the installation, with weld records, as-builts, Spanish procedures and validation protocols handed over with the system. Send your scope, site and import route to request a quote.

Standards referenced: NOM-020-STPS-2011 Pressure vessels, cryogenic vessels and steam generators or boilers · NOM-001-SEDE-2012 Electrical installations · NOM-059-SSA1-2015 Good manufacturing practices for medicines · NOM-241-SSA1-2025 Good manufacturing practices for medical devices · NOM-012-SCT-2-2017 Vehicle weights and dimensions · ASME Boiler and Pressure Vessel Code Section VIII · ASME B31.3 Process Piping · ASME BPE · PIC/S GMP Guide · USMCA (T-MEC), Chapter 5 Origin Procedures · IMMEX Decree · Incoterms 2020 · ISPM 15

Frequently asked questions

Who builds pharmaceutical water systems for plants in Mexico City and Toluca?

Paul Industries builds purified water and WFI systems, clean steam generators and distribution loops for pharmaceutical plants in Mexico City, Toluca and the rest of the State of Mexico. Each system is documented to NOM-059-SSA1-2015 and the PIC/S GMP Guide that COFEPRIS follows, with Spanish operating procedures and qualification protocols, and Paul executes the site acceptance test, IQ and OQ at the plant.

Does a US-built ASME vessel meet NOM-020-STPS-2011?

NOM-020-STPS-2011 places its obligations on the plant that operates the vessel, so an ASME vessel meets it once the plant’s file is complete: classification, data sheet, construction code, test pressure, drawings, nameplate record and, for Category III, a signed calculation memo and the STPS control number. Paul Industries ships every vessel with the documents that file needs, in Spanish and in SI units.

What NOM-020 category does a pressure vessel on a skid fall into?

The category depends on the relief device set pressure, the fluid and the volume. A vessel with water or air up to 490.33 kPa and 0.5 cubic metres is Category I, while any non-hazardous fluid vessel set above 784.53 kPa, or any hazardous fluid vessel set above 686.47 kPa, is Category III. Paul Industries classifies every vessel on a skid during design so the plant knows which files and notices it needs.

Do operating manuals for a Mexican plant have to be in Spanish?

NOM-020-STPS-2011 requires operating, review and maintenance procedures for pressure equipment to be written in Spanish, and Mexican GMP inspections are conducted in Spanish as well. Paul Industries supplies Spanish procedures, manuals, nameplates and HMI alarm text, and keeps a matching English set for the buyer’s corporate engineering and quality teams.

What is a USMCA certificate of origin, and who prepares it?

A USMCA certificate of origin is the set of data that supports duty-free entry of originating goods into Mexico: certifier, exporter, producer and importer, goods description, tariff classification and origin criterion. It has no mandatory form and may appear on the commercial invoice. Paul Industries reviews the bill of materials for origin during design and issues the certification with the shipment when the equipment qualifies.

Under a Mexico IMMEX program, can a plant in Monterrey import a process skid temporarily?

A plant in Monterrey holding an IMMEX program imports machinery and equipment temporarily for the life of its program, and with VAT and IEPS certification it receives a credit for the VAT on that import. The asset must be tracked in the plant’s IMMEX inventory control system. Paul Industries structures the invoice, serial numbers and values so the skid enters the plant’s IMMEX records cleanly.

Is there an official USMCA certificate of origin form or USMCA certificate of origin template?

Mexico, the United States and Canada accept a certification of origin in any format, so no single USMCA certificate of origin form is mandatory. Any USMCA certificate of origin template works if it holds the minimum data elements: certifier, exporter, producer, importer, goods description, tariff classification, origin criterion, blanket period where used, and a signed statement. Paul Industries places the certification on its commercial invoice or on a separate sheet, whichever the importer’s agente aduanal prefers.

What does the agente aduanal need from the equipment supplier?

The agente aduanal needs a commercial invoice with values and clear technical descriptions, a packing list that matches each crate’s marks, weights and dimensions, tariff classification support, serial numbers and the origin certification. Paul Industries prepares that set before the truck leaves the shop so the pedimento is filed without queries at the border.

How do skids from the US East Coast reach plants in Queretaro and Guanajuato?

Skids for Queretaro, Guanajuato and the rest of the Bajio usually move by road through Laredo, the busiest US border crossing, then continue on a Mexican carrier with the Carta Porte document. Loads wider than 2.60 metres or taller than 4.25 metres need special authorization under NOM-012-SCT-2-2017, so Paul Industries sizes skids for the legal envelope whenever the process allows.

When is a sea route to Altamira or Veracruz better than trucking?

A sea route to Altamira or Veracruz suits tall columns, heavy vessels and modules that exceed Mexican road dimensions, and plants near the Gulf coast. Published routings show about ten and a half days between Savannah and Altamira with one transfer. Paul Industries compares the road and sea options once crated sizes are known and books the route that protects the installation date.

Does Paul Industries build ultrapure water systems for electronics plants in Guadalajara?

Paul Industries builds ultrapure and high-purity water systems, chemical distribution and process cooling for electronics and semiconductor plants in Guadalajara and across Jalisco, home of the Jalisco Electronics Manufacturing Cluster. Panels are built for the plant’s 440 V or 480 V supply with Spanish HMI text, and Paul installs and commissions the systems or supervises the plant’s team.

Is Mexico 50 Hz or 60 Hz, and what voltage do plant panels use?

Mexico runs at 60 Hz, like the United States, so motor speeds and pump curves carry over. Building services usually run at 127/220 V, and industrial three-phase power appears at 440 V and 480 V, including 254/440 V and 277/480 V systems. Paul Industries confirms the plant’s supply from its single-line diagram and builds every panel to NOM-001-SEDE-2012 for that voltage.

Which Mexican GMP rules apply to medical device plants?

Medical device plants follow NOM-241-SSA1-2025, published on April 4, 2025 and in force since November 30, 2025, replacing the 2021 edition. COFEPRIS enforces it. Paul Industries documents water systems, clean utilities and process equipment for device plants across Mexico to that standard, with Spanish protocols and records.

What does the cost of a delivered system for a Mexican plant depend on?

The cost of a delivered system depends on the NOM documentation for each vessel, the electrical design for the plant’s voltage, the freight route and any oversize permits, duties and VAT under the chosen Incoterm and import route, and whether Paul Industries installs the system or supervises the plant’s team. Each appears as its own line in a US dollar quote, starting with a budget range.

What is a pedimento number used for after the equipment arrives?

The pedimento number identifies the customs entry under which the equipment was imported, and the plant keeps it with the asset record to prove legal import during tax, customs or IMMEX audits. For temporary imports it also links the asset to the plant’s IMMEX inventory control records. Paul Industries keeps invoice and serial data consistent so the pedimento, the asset tag and the NOM-020 file all match.

Does a factory acceptance test happen in Mexico or in the US shop?

The factory acceptance test runs in Paul Industries’ US shop before the equipment is crated, against a protocol the plant approves in advance, with engineers attending in person or by live video. The site acceptance test then repeats the checks that shipping and installation affect, at the plant in Mexico, followed by IQ and OQ for regulated sites.

Which Incoterm do Mexican plants usually choose for a US equipment order?

Mexican plants usually choose DAP or FCA, because the importer of record must be registered in the Padron de Importadores and most plants keep that role with their own agente aduanal. Under DAP, Paul Industries carries freight and transit risk to the named plant; under FCA, the plant’s carrier collects at Paul’s dock. CIF suits sea shipments to Altamira or Veracruz.

Does Paul Industries take projects at food and beverage plants in Mexico?

Paul Industries supplies and installs clean-in-place units, mixing and storage tanks, sanitary lines, glycol and chilled water loops and water treatment for food and beverage plants across Mexico, including brewing, bottling and dairy plants in Nuevo Leon, Jalisco and the Bajio. Vessels are documented for NOM-020-STPS-2011 and panels for NOM-001-SEDE-2012, with Spanish procedures and operator training at handover.

Planning a process system for a plant in Mexico?

Send the site, the scope or P&IDs, the plant’s supply voltage, whether it imports under IMMEX and your preferred Incoterm, and Paul Industries will return a NOM review, a shipping plan and a first budget estimate. Call 201-450-8280 or request a quote.