Paul Industries is a US process equipment contractor for Japan that engineers and fabricates skids, pressure vessels, tanks, purified water and ultrapure water systems in the United States, runs the factory acceptance test, ships the equipment to Yokohama, Kobe or Nagoya, and then installs, starts up and commissions it at the Japanese plant or supervises the installation. Boilers and vessels are built and documented to the Industrial Safety and Health Act, gas and refrigeration equipment to the High Pressure Gas Safety Act, motors and panels to the grid frequency of the site, and GMP systems to the ordinance that PMDA inspects against. Headquarters are at 256 Shore Drive in Kilmarnock, Virginia.
Request a quote or call 201-450-8280
What a US process equipment contractor for Japan delivers to a Japanese plant
A US process equipment contractor for Japan delivers finished, tested process systems rather than loose components: the plant receives a skid or module that has already run on water, been pressure tested and been checked loop by loop against its own P&IDs. Paul Industries carries the work from the first heat and mass balance through fabrication, factory testing, export crating and ocean freight to the field work in Japan, and the same team that drew the system starts it up. Japanese owners value that continuity, because the engineer who answers a question during qualification is the engineer who made the design decision.
The range covers purified water and WFI systems, clean steam generators, ultrapure water plants for wafer fabs, ASME pressure vessels and process tanks, pump and dosing skids, CIP circuits and refrigeration packages. Plants choose among three delivery routes: equipment supply with installation supervision, design-build in which Paul also lays out the utility room and the interconnecting piping, or complete installation with Paul on site from setting through qualification. Each route uses the same documentation set, so a plant that starts with supervision and later adds a turnkey line works from one records format. The full list of countries Paul serves sits on the international page.
Pharmaceutical industry in Japan: plants that buy process systems
The pharmaceutical industry in Japan is investing in new manufacturing buildings for both synthetic and biologic medicines, and each building needs water, steam, cleaning and process utilities. Chugai Pharmaceutical completed its FJ3 building at the Fujieda plant in Shizuoka in 2024, a 55.5 billion yen investment for small molecule and macrocyclic peptide active ingredients, and opened its UK4 building at Ukima in Tokyo for early clinical biologic supply after a 12.1 billion yen investment. Takeda’s Hikari plant in Yamaguchi, founded in 1946 on the Seto Inland Sea, runs small molecule, sterile, biologic and vaccine production on one site.
Pharmaceutical manufacturers in Japan buy the systems that sit at the center of pharmaceutical process work: purified water and water for injection generation and loops, clean steam, CIP and SIP skids, solvent and buffer handling, and jacketed reactors and receivers for active ingredient synthesis. Biologic suites add media and buffer preparation, harvest and chromatography utilities and the closed transfer systems described on the biotech page. Japan pharmaceutical manufacturing places heavy weight on documented change control, so equipment arrives with design history, material certificates and test records filed in the order a Japanese quality unit audits them.
Semiconductor fabs from Kumamoto to Chitose
Japan’s semiconductor build-out spans the country from Kyushu to Hokkaido. The first JASM fab in Kumamoto, majority owned by TSMC, began mass production at the end of 2024 on 12 to 28 nanometer processes. Rapidus powered up its 2 nanometer pilot line at the IIM-1 fab in Chitose, Hokkaido, on April 1, 2025, with volume production targeted for around 2027. Micron broke ground in 2026 on an expansion of about 1.5 trillion yen at its Hiroshima memory fab, the site that produced its first high bandwidth memory wafer, and Kioxia is adding a third fab at Kitakami in Iwate alongside its Yokkaichi operations. Each fab draws on ultrapure water, process cooling water, chemical distribution and exhaust treatment, the utilities at the core of semiconductor work.
| Region | Grid | Typical plants | Systems Paul builds |
|---|---|---|---|
| Kanto (Tokyo, Kanagawa) | 50 Hz | Biologics, clinical supply, research plants | WFI and purified water, clean steam, media and buffer skids |
| Shizuoka and Chubu | 60 Hz west of the Fuji River | Active ingredient synthesis, memory fabs at Yokkaichi | Reactors and receivers, solvent skids, ultrapure water |
| Kansai (Osaka, Kobe) | 60 Hz | Pharmaceutical and chemical plants | CIP and SIP circuits, process vessels, dosing skids |
| Chugoku and Yamaguchi | 60 Hz | Memory fabs, vaccine and sterile plants | Process cooling, chemical distribution, WFI loops |
| Kyushu (Kumamoto) | 60 Hz | Logic and image sensor fabs | Ultrapure water, process cooling water, exhaust utilities |
| Tohoku and Hokkaido | 50 Hz | Flash memory and advanced logic fabs | Ultrapure water, chilled water plants, pump skids |
Which rules govern the Japan pressure vessel code for imported equipment?
The Japan pressure vessel code for imported equipment is the set of structural standards issued by the Ministry of Health, Labour and Welfare under the Industrial Safety and Health Act: the Construction Code for Boilers and the Construction Code for Pressure Vessels. Under the Industrial Safety and Health Act, Japan sorts pressure equipment into boilers, small boilers, first class pressure vessels, second class pressure vessels and small pressure vessels, and the class sets how the design is appraised and which inspections the vessel passes before use. Boilers and first class vessels rank among the high-danger machines the law singles out: the manufacturer or importer submits them to inspection by the Prefectural Labour Bureau or an authorized inspection agency.
Japanese pressure vessel regulations give a foreign manufacturer a direct route: the manufacturer files the application itself, and inspection data from a foreign inspection agency designated by the Minister of Health, Labour and Welfare forms part of that application. That shapes a US project in practical ways. The design calculations follow the MHLW structural standard for the vessel’s class, material specifications are matched to what the standard accepts, and inspection points during fabrication are planned with the designated agency so the evidence exists when the vessel ships. Paul Industries builds the vessel file around those requirements from the purchase order, so the inspections in Japan review a complete record rather than reconstruct one. Pressures in every document are stated in megapascals, the unit Japan has used for pressure equipment since October 1999.
| Law or rule | Authority | What it covers on a skid | What Paul delivers |
|---|---|---|---|
| Industrial Safety and Health Act | MHLW, Prefectural Labour Bureaus | Boilers and first and second class pressure vessels | Design to the MHLW structural standard, fabrication and test records for inspection |
| High Pressure Gas Safety Act | METI, KHK | Equipment holding compressed gas at 1 MPa or more, liquefied gas at 0.2 MPa or more | Designed equipment documented for the specified equipment inspection |
| Electricity Business Act | METI | Conformity of electrical facilities to technical standards | Panels and motors rated for the site’s voltage and frequency |
| GMP Ministerial Ordinance | MHLW, PMDA, prefectures | Manufacturing control and quality control for drugs | URS, DQ, IQ and OQ protocols and executed records |
| Customs Act and consumption tax | Japan Customs | Import declaration, duty and 10 percent consumption tax | Invoice, packing list and origin papers matched to the declaration |
High Pressure Gas Safety Act and the specified equipment inspection
The High Pressure Gas Safety Act, the Japan High Pressure Gas Control Law as older English translations name it, applies wherever a system holds compressed gas at 1 megapascal or more at its operating temperature, or liquefied gas at 0.2 megapascals or more. Refrigeration packages, ammonia and CO2 systems, nitrogen and compressed gas skids and some reactors fall inside it. Equipment the act designates as specified equipment passes an inspection under Article 56-3 by METI, the High Pressure Gas Safety Institute of Japan (KHK) or a designated conformity inspection body, and foreign manufacturers apply for that inspection for equipment built for export to Japan. Paul Industries identifies every item that the act reaches during the code review, designs refrigeration and gas equipment to the technical standards it sets, and organizes the material, weld and test evidence the inspection calls for.
Two regimes on one skid is common. A clean steam generator with a compressed air receiver, or a chiller package bolted to a process water skid, mixes MHLW and KHK equipment on one frame, and each component follows its own law. Paul lists the governing law beside every pressure-retaining item on the bill of materials, which gives the Japanese plant a single sheet showing which inspection each part needs.
Electrical supply in Japan: 50 Hz east, 60 Hz west
Electrical supply in Japan runs at 50 Hz in the east, including Tokyo, Tohoku and Hokkaido, and at 60 Hz in the west, including Osaka, Chubu, Chugoku and Kyushu, with the dividing line near the Fuji River in Shizuoka. Low voltage service is 100 V and 200 V, three phase industrial supply is 200 V, and larger plants take 400 V class supply. Electrical facilities must conform to the technical standards set under the Electricity Business Act.
The split matters more in Japan than anywhere else Paul ships. A design built for a Kumamoto fab runs at 60 Hz, while the same design for a Chitose fab runs at 50 Hz, so a pump that meets its duty point in Kyushu falls short in Hokkaido unless its impeller or drive is selected for that grid. Paul confirms the frequency and voltage of the receiving substation before any motor, transformer or drive is bought, selects pumps on curves for that frequency, and states both on every nameplate and panel schedule. Control panels are built to IEC 60204-1 with metric conductor sizes and the plant’s preferred PLC platform, and drives are sized so a multinational owner with plants in both halves of the country runs one control program with two motor sets.
Seismic design, units and documentation
Japanese plants design for earthquakes as a routine load, so skid frames, vessel supports and anchor bolts are sized to the seismic loads in the plant’s structural basis, and flexible connections are placed where equipment ties into building-supported piping. Paul Industries checks the frame, the anchorage and the lifting points against those loads during design and records the calculation in the turnover package. Drawings are metric throughout, with pressures in megapascals, sizes in DN and tags following the owner’s numbering rules. Operating staff, inspectors and regulators in Japan work in Japanese, so manuals, labels and qualification protocols are issued in the language the plant specifies, with English and Japanese side by side where the owner’s group uses both.
PMDA GMP, the GMP ordinance and PIC/S in Japan
PMDA GMP inspections in Japan apply the Ministerial Ordinance on Standards for Manufacturing Control and Quality Control for Drugs and Quasi-drugs, MHLW Ordinance No. 179 of 2004, revised in 2021 to align with the PIC/S guide. Japan joined PIC/S in July 2014, with PMDA, MHLW and the 47 prefectures as participating authorities, and PMDA uses the PIC/S GMP Guide within the scope of the ordinance. Equipment for a Japanese plant is therefore qualified against the same structure an EU or PIC/S inspector expects: a user requirement specification, design qualification, installation and operational qualification, and traceable change control.
Water systems follow the Japanese Pharmacopoeia for products registered in Japan, and many multinational plants design to the Japanese, European and United States monographs at once so one loop serves every market. Paul Industries designs the loop for the most demanding monograph the plant names, sets alert and action limits in the control system to match, and runs the IQ and OQ through validation and commissioning with the plant’s quality unit, so the executed protocols file straight into the site’s GMP records.
Shipping and importing equipment into Japan
Importing equipment into Japan from the US East Coast starts with an all-water voyage through the Panama Canal that forwarders put at about 30 to 40 days from New York, with 25 to 30 of those days at sea, and up to about 46 days on routings that call at other ports first. Yokohama and the Tokyo Bay ports serve Kanto plants, Nagoya serves Chubu and Yokkaichi, and Kobe and Osaka serve Kansai and the Seto Inland Sea coast. Paul books the sailing to the port nearest the plant, fixes the factory acceptance test date backward from that sailing, and plans the inland move around Japanese road limits, which favor modules sized well inside a standard container or flat rack.
Japan’s duty on most process machinery is low: the simple average applied rate is 0.0 percent for non-electrical machinery and 0.2 percent for electrical machinery, assessed on the CIF value, and the US-Japan Trade Agreement sets lower rates on some lines. Consumption tax of 10 percent, combining a 7.8 percent national rate with 2.2 percent levied for prefectures and municipalities, is charged on the CIF value plus any duty. The importer files the declaration through NACCS, Japan’s electronic customs system. Under Incoterms 2020, Japanese buyers with a group forwarder usually take FCA at a US port; buyers that want Paul to hold the risk to the plant gate pick DAP, and DDP adds the consumption tax and clearance to Paul’s scope. Quotes are in US dollars, with the Incoterm named on the quote.
Export classification before the crates close
Export classification on the US side runs alongside design. Wetted parts in high-nickel alloys, tantalum, titanium, glass lining or fluoropolymer linings are screened against export control number 2B350, which matters for semiconductor chemical distribution and corrosive pharmaceutical service, and Electronic Export Information is filed where the shipment requires it. Paul fixes each item’s classification at purchase, so the export documents match the material list when the cargo reaches the dock.
Preservation and receiving inspection in Japan
Japanese receiving teams inspect incoming equipment closely, often against a written checklist that lists every nozzle cap, desiccant pack and shock indicator, and a damaged polish or a wet line becomes a nonconformance before the skid leaves the dock. Paul Industries prepares for that inspection at the factory. Every line is drained and blown dry after the hydrostatic test, electropolished surfaces are capped and wrapped, instruments that dislike vibration ship boxed in the same crate with their tag numbers, and crates carry tilt and shock indicators along with humidity cards. A photo record of each crate’s contents goes to the plant before sailing, so the receiving team checks the arrival against the same images. The Pacific crossing passes through humid tropical waters near the canal, so vapor barrier and desiccant quantities are sized for the full voyage, and vessels are nitrogen blanketed where the specification asks for it. When the crates are opened at the plant, the first site activity is a joint walkdown against that photo record, signed by both teams.
How a Japanese project with Paul Industries runs
Nine steps take a Japanese project with Paul Industries from enquiry to service, and the opening review decides which law governs each pressure-retaining item, which grid the site sits on and which GMP records the plant expects. The table below lists each step with the record a Japanese plant keeps from it.
| Step | Work | Japan-specific record |
|---|---|---|
| 1. Code and grid review | MHLW or KHK status of every vessel, site frequency and voltage confirmed | Governing-law list per item, electrical basis |
| 2. Engineering | P&IDs, layout, seismic frame and anchorage design, panel design | Calculations to the MHLW structural standard, metric drawings |
| 3. Fabrication in the United States | Welding, assembly, wiring and instrumentation with traceable materials | Inspection data for the vessel application, weld maps |
| 4. Factory acceptance test | Hydrostatic, functional and sequence testing at frequency | Signed FAT record, witnessed on site or by video |
| 5. Crating and ocean freight | Drying, sealing, ISPM 15 crates, booking to Yokohama, Nagoya or Kobe | Packing list and invoice matched to the NACCS declaration |
| 6. Installation or supervision | Setting, anchoring and tie-ins at the plant | Installation checklist and red-lined drawings |
| 7. Start-up | Flushing, passivation where specified, first runs | Start-up log with tuned setpoints |
| 8. Qualification | SAT, IQ and OQ under the GMP ordinance | Executed protocols for the quality unit |
| 9. Handover and service | Training, spares and a service plan | As-builts, manuals in the plant’s language, inspection files |
Japan runs 13 or 14 hours ahead of US Eastern time depending on the season, so witnessed test sequences that Japanese engineers follow by video are scheduled for the US evening, which is their morning. In-person witnessing is set around the sailing date, and after handover the drawings, test data and control program stay on file so service questions are worked through with the plant on a shared screen before parts ship.
Who builds process systems for plants in Japan?
Paul Industries builds process systems for plants in Japan, whether the order is one chemical dosing skid or an entire water, steam and cooling utility building, and stays responsible from the US test floor until the system runs qualified at the Japanese site. Engineering, US fabrication and testing come first; then Paul documents every boiler and vessel for the MHLW inspections and every gas-holding item for the KHK inspection, wires it for the site’s grid, and qualifies GMP systems to the ordinance PMDA inspects against. Having moved from northern New Jersey to Pennsylvania and then to its present base at 256 Shore Drive in Kilmarnock, Virginia, the company takes work in all 50 states and abroad, including 60 Hz projects for plants in South Korea and tropical builds for Singapore plants.
What drives the cost of a process equipment project in Japan?
The delivered cost of a process equipment project in Japan depends on five lines beyond the equipment itself, and Paul Industries prices each one separately so the plant sees where the money goes.
- Japanese inspection documentation. Vessels built to the MHLW structural standards and items subject to KHK inspection add engineering and inspection hours that grow with the number of pressure-retaining items on the skid.
- Grid and seismic design. Motors, drives and transformers for 50 or 60 Hz and frames sized for seismic loads set part of the material cost.
- Freight and inland handling. Sailing routing, module size and Japanese road limits decide between containers, flat racks and the number of shipments.
- Taxes under the chosen Incoterm. Under FCA or DAP the plant pays the 10 percent consumption tax at import; under DDP the tax and clearance sit in Paul’s price.
- Installation route. Supervision books fewer Paul technicians in Japan; complete installation keeps start-up and qualification with the firm that built the system.
An early budget figure comes from comparable past scope, and the fixed price follows once the drawings, the governing-law list and the Incoterm are settled.
Paul Industries for Japanese plants
Paul Industries engineers, fabricates, tests, ships and commissions process equipment for pharmaceutical plants, semiconductor fabs and chemical sites across Japan, from Kanto to Kyushu and Hokkaido. Each system leaves the United States wired for the frequency of its site, with its boilers and vessels documented for the Industrial Safety and Health Act inspections, its gas-holding items ready for KHK, and its GMP records ready for the plant’s quality unit. Japanese plants starting a project send the P&IDs, the site grid and the delivery terms they prefer when they request a quote from Paul.
Standards referenced: Industrial Safety and Health Act · MHLW Construction Code for Boilers · MHLW Construction Code for Pressure Vessels · High Pressure Gas Safety Act · Electricity Business Act technical standards · MHLW GMP Ministerial Ordinance (No. 179 of 2004, revised 2021) · PIC/S GMP Guide · Japanese Pharmacopoeia · ASME Boiler and Pressure Vessel Code Section VIII · ASME B31.3 · IEC 60204-1 · ISO 14644-1 · Incoterms 2020 · ISPM 15
Frequently asked questions
What does the Japan pressure vessel code require of a vessel built in the United States?
A vessel for Japan is designed to the MHLW Construction Code for Pressure Vessels for its class, built from materials that code accepts, and inspected during fabrication so the record supports the inspections under the Industrial Safety and Health Act. A foreign manufacturer files the application directly, with data from an inspection agency the Minister of Health, Labour and Welfare designates. Paul Industries plans that record from the purchase order onward.
How does Japan classify the boilers and pressure vessels on a process skid?
The Industrial Safety and Health Act sorts equipment into boilers, small boilers, first class pressure vessels, second class pressure vessels and small pressure vessels, based on pressure, size and contents. The class decides how the design is appraised and which inspections apply before use. Paul Industries classifies every pressure-retaining item on a skid during the code review and lists the class beside the item on the bill of materials.
When does a refrigeration or gas skid fall under the High Pressure Gas Safety Act?
The act applies to compressed gas at 1 megapascal or more at its operating temperature and to liquefied gas at 0.2 megapascals or more. Ammonia and CO2 refrigeration, nitrogen skids and compressed gas packages usually reach those levels. Paul Industries designs such equipment to the act’s technical standards and prepares the material, weld and test evidence for the specified equipment inspection by KHK or a designated inspection body.
Does Japan have an FDA that inspects drug plants?
Japan’s drug regulator is the Ministry of Health, Labour and Welfare, working with the Pharmaceuticals and Medical Devices Agency (PMDA) and the 47 prefectures, which together inspect manufacturing sites against the GMP ministerial ordinance. Japan has been a PIC/S member since 2014. Paul Industries qualifies water, steam and process systems with protocols written to that ordinance so the records support the plant’s inspections.
Which grid frequency applies to fabs in Kumamoto and in Chitose, Hokkaido?
Kumamoto sits on Kyushu’s 60 Hz grid, while Chitose in Hokkaido is on the 50 Hz eastern grid. A pump, fan or compressor selected for one site falls off its duty point at the other unless the motor, impeller or drive is chosen for that frequency. Paul Industries confirms the substation frequency and voltage at the start and selects every rotating machine for it.
How long does a skid take to reach Yokohama from the US East Coast?
Forwarders quote about 30 to 40 days from New York to Yokohama via the Panama Canal, with 25 to 30 days at sea, and up to about 46 days on routings with extra calls. Canal restrictions and port congestion move those figures. Paul Industries books the sailing when the crate list is final and carries the voyage as its own line in the project schedule between FAT and site arrival.
Which Japanese port suits a plant in Osaka, Nagoya or Yokkaichi?
Kansai plants around Osaka usually receive equipment through Kobe or Osaka, plants in Chubu and Yokkaichi through Nagoya, and Kanto plants through Yokohama or Tokyo. Choosing the nearest port shortens the road leg, which matters because Japanese road limits restrict oversize loads. Paul Industries sizes modules for the inland route as well as for the ocean container or flat rack.
Is US-built process machinery subject to customs duty in Japan?
Japan’s simple average applied tariff is 0.0 percent on non-electrical machinery and 0.2 percent on electrical machinery, and the US-Japan Trade Agreement lowers some rates further. Duty is assessed on the CIF value. The larger import cost is the 10 percent consumption tax on the CIF value plus duty, which plants registered for consumption tax generally recover. Paul Industries supplies origin documents with each shipment.
How is the consumption tax on an imported skid calculated in Japan?
Japan charges consumption tax of 10 percent at import, split between a 7.8 percent national rate and 2.2 percent for prefectures and municipalities, on the CIF value of the goods plus any customs duty. A skid with a CIF value of 100 million yen and no duty carries 10 million yen of consumption tax. Under DDP terms Paul Industries pays it and includes it in the price; under FCA or DAP the importer pays it.
Does Paul Industries build ultrapure water systems for fabs in Kumamoto, Hiroshima and Kitakami?
Paul Industries designs, fabricates and installs ultrapure water production, polishing and distribution for semiconductor fabs across Japan, including the Kumamoto, Hiroshima and Kitakami fab regions. Wetted materials are chosen from PVDF, other high-purity polymers and electropolished stainless steel to meet the resistivity, TOC and particle limits the fab specifies, controls are wired for the site’s grid, and the system is commissioned with the fab’s facilities team after it arrives.
Does Paul Industries supply WFI and clean steam systems to pharmaceutical manufacturers in Japan?
Paul Industries builds WFI and purified water generation, storage and distribution, and clean steam generators, for pharmaceutical manufacturers in Japan, then qualifies them on site under the GMP ordinance. The design meets the Japanese Pharmacopoeia and any other monograph the plant’s products are registered against, and any boiler-class component ships with its MHLW inspection file.
How is a control panel for a Japanese plant designed?
Panels for Japan follow IEC 60204-1 practice with metric conductors and are rated for the site’s 200 V or 400 V class supply at 50 or 60 Hz, and the installation conforms to the technical standards under the Electricity Business Act. Paul Industries builds the panel on the PLC platform the plant standardizes on and labels it in the language the plant specifies.
How does seismic risk in Japan change skid design?
Japanese plants treat earthquakes as a design load, so skid frames, vessel legs and anchor bolts are sized to the seismic forces in the plant’s structural basis, tall vessels get bracing, and flexible connections separate skid piping from building-supported lines. Paul Industries runs those checks during design, records them in the calculation package, and verifies anchorage during installation.
What language do operating manuals for a Japanese plant use?
Operators, maintenance staff and inspectors in Japan work in Japanese, so manuals, labels and qualification protocols are issued in the language the plant specifies, often Japanese with English alongside for a multinational owner. Paul Industries agrees the language plan in the first project meeting so every document, from nameplates to the IQ protocol, follows it from the first draft.
Which Incoterm do Japanese buyers pick for a first equipment order from the United States?
Buyers with a group forwarder often take FCA at a US port and run the ocean leg themselves. Buyers placing a first order frequently choose DAP to the plant, so Paul Industries holds freight and transit risk to the gate while the importer handles the NACCS declaration and consumption tax. DDP adds clearance and tax to Paul’s scope. Paul prices each option side by side on request.
What does Paul Industries hand over when a Japanese project closes?
The handover set includes as-built drawings, design calculations, the inspection files for MHLW and KHK equipment, weld logs and material certificates, factory and site test reports, the executed qualification protocols, manuals in the agreed language, the control program and a spare parts list sized for ocean lead times to Japan. Records are delivered in the plant’s document format.
What should a Japanese plant send Paul Industries to get a price in US dollars?
Send the process duty or P&IDs, the site address and its grid frequency, the utilities available, the plant’s engineering standards, the GMP classification for pharmaceutical work, the language plan for documents, your preferred Incoterm and whether you want supervision or complete installation. Paul Industries replies with a governing-law list, a sailing plan and an estimate in US dollars.
Planning a process system for a plant in Japan?
Tell us the process duty, the Japanese site and its grid frequency, and Paul Industries will come back with the code basis, the shipping plan and an estimate in US dollars. Call 201-450-8280 or request a quote.
