Paul Industries provides tank fabrication in New Jersey for chemical, pharmaceutical, food, terminal and utility owners, designing and building carbon steel and stainless storage and process tanks with the containment, overfill protection and integrity records that NJDEP’s discharge prevention rules expect. Shop-built and field-erected tanks, jacketed and agitated process tanks, day tanks and replacement shells are designed, welded, tested, set, piped and documented under one contract. The state’s rules reach further than the federal spill rule in several places, so the design starts with the regulations rather than ending with them.
Request a quote or call 201-450-8280
Which NJ DEP storage tank regulations apply to a new tank?
The NJ DEP storage tank regulations that apply to a new tank depend on whether it sits above or below ground and on what the whole site stores. Aboveground tanks at a major facility fall under N.J.A.C. 7:1E, the discharge prevention rules adopted under the Spill Compensation and Control Act, while underground tanks fall under N.J.A.C. 7:14B. Federal spill prevention, 40 CFR Part 112, applies on top of both wherever oil is stored.
| Program | What it covers | What it asks of a new or replacement tank |
|---|---|---|
| NJDEP discharge prevention, N.J.A.C. 7:1E | Major facilities storing petroleum and other hazardous substances | Containment, impermeable base, overfill alarms, valves, integrity testing, and listing in the DPCC and DCR plans |
| NJDEP underground storage tanks, N.J.A.C. 7:14B | Regulated underground tanks, including non-residential heating oil tanks over 2,000 gallons | Registration by the owner, technical standards, and work by individuals and firms holding NJDEP certification |
| EPA spill prevention, 40 CFR 112 | Sites with more than 1,320 gallons of aboveground oil capacity in containers of 55 gallons or more, or more than 42,000 gallons buried | A spill prevention, control and countermeasure plan covering every oil container |
| Construction and fire codes | Every tank installation | Permits, foundations, anchorage, venting and spacing reviewed by the municipal officials |
| Product and sanitary standards | Pharmaceutical, food and beverage tanks | ASME BPE or 3-A finishes, drainability and cleanability |
The first decision is therefore a site question: does the facility, counted across its contiguous properties, reach major facility status? Water, sugar, milk and many process tanks carry no hazardous substance and never count; solvent, acid, caustic, fuel and many chemical intermediates do.
When does a New Jersey site become a major facility?
A New Jersey site becomes a major facility under N.J.A.C. 7:1E-1.6 when the same owner or operator, across one or more contiguous or adjacent properties, has a combined storage capacity of 200,000 gallons or more of hazardous substances of all kinds, petroleum included, or 20,000 gallons or more of hazardous substances other than petroleum. Capacity counts, not the volume actually stored, and a site that adds tanks and crosses either line becomes a major facility from that point.
The lower non-petroleum threshold catches many plants that think of themselves as small. A chemical blender with four 6,000-gallon acid and caustic tanks is already over 20,000 gallons. Paul Industries totals the existing and proposed storage at the start of a project, by substance class, so the owner knows before the purchase order whether the new tank tips the site into the program.
Once a site is a major facility, the rules require two plans: a Discharge Prevention, Containment and Countermeasure (DPCC) plan showing how the site meets the equipment standards, and a Discharge Cleanup and Removal (DCR) plan describing the response. NJDEP’s renewal guidance has the plans reviewed, revised and resubmitted to the Bureau of Release Prevention every three years, a 2025 rule proposal would lengthen that to five, and the Spill Act calls for an amendment within 30 days of a facility change that requires one. New equipment must meet the standards before it goes into service.
NJ DPCC regulations and the federal NJ SPCC plan
The NJ DPCC regulations and the federal SPCC rule overlap, and each stands on its own. A New Jersey site storing oil above the federal thresholds keeps an SPCC plan under 40 CFR 112, and if it is also a major facility it keeps the DPCC and DCR plans as well. Paul Industries supplies the tank data that the NJ SPCC plan and the DPCC plan both draw on: capacity, material, construction standard, containment volume, overfill devices and the integrity test schedule.
New Jersey aboveground storage tank regulations for a new tank
New Jersey aboveground storage tank regulations at N.J.A.C. 7:1E-2.2 set the equipment a new tank at a major facility needs: secondary containment or a diversion system, a base the stored substance cannot pass through, valves close to the shell on every line entering below the liquid level, overfill protection, and an integrity testing program. Each item belongs on the fabrication drawings, since most are much cheaper to build in than to add later.
| Requirement | What the rule says | How the tank is built for it |
|---|---|---|
| Secondary containment | Containment or a diversion system built to N.J.A.C. 7:1E-2.6 | Dike, berm, double wall or containment pan sized with the tank layout |
| Impermeable base | Base impermeable to the stored substance; existing tanks comply at reconstruction, replacement or bottom replacement | Liner or coated concrete pad, leak detection under the floor of field-erected tanks |
| Valves on lower lines | Lines entering below the liquid level need remotely activated or readily accessible valves close to the shell | Shell valves on the first flange, actuated where access is poor |
| Piping through containment | Only where the wall, dike or berm keeps its integrity | Sealed sleeves, or piping routed over the dike |
| High-level alarm | Audible or visual alarm at a set level, plus a high-high pump cutoff on a separate detector or direct contact with the person controlling the fill | Independent level switches and transmitter nozzles placed on the shell |
| Small tanks | Tanks of 2,000 gallons or less may instead be attended throughout filling | Sight gauge or level indicator at the fill point |
| Vents and overfill lines | Discharge into containment or another tank | Vent and overflow outlets routed inside the dike |
| Heating coils | Coil leakage captured by containment or treatment | Coil drains and condensate outlets monitored or routed to treatment |
Containment sized to the New Jersey rule
Containment for a New Jersey storage area must hold at least the volume of the largest tank or container in it under N.J.A.C. 7:1E-2.6, plus six inches of rainwater wherever rain can collect, and every component must be impermeable and kept that way. Dikes, berms, retaining walls, curbing, sumps and drip pans all qualify when they meet that test. For a 30,000-gallon tank in an open dike, six inches of rain across the diked floor area adds real volume, so Paul Industries sizes the dike from the layout rather than the tank alone, and coordinates tank height and diameter with the space the containment can take.
How often should above ground storage tanks be inspected in New Jersey?
How often should above ground storage tanks be inspected in New Jersey depends on how they were built: under N.J.A.C. 7:1E-2.16, steel tanks over 2,000 gallons at a major facility follow the schedules of API 653, STI SP001, API 510 or ASME Section VIII according to their type, while fiberglass, plastic and other tanks are inspected every five years. New field-erected tanks are tested to their construction standard before service, and shop-built tanks receive a post-installation test such as a static head test.
| Construction | Standard or method | Frequency | Design consequence |
|---|---|---|---|
| Field-erected steel, atmospheric | API 653 | On the standard’s schedule; risk-based scheduling not allowed | Bottom access, settlement survey points, nameplate data for future evaluations |
| Shop-built steel, atmospheric | API 653 or SP001 | On the chosen standard’s schedule | Elevated or double-wall designs that make external inspection simple |
| Steel, pressurized | API 510 or ASME Section VIII | On the applicable standard’s schedule | Built and stamped as a pressure vessel |
| Fiberglass reinforced plastic | ASTM E1067 acoustic emission plus internal and external inspection | Every five years | Manway and access for internal inspection |
| Homogeneous plastic | Internal and external visual inspection | Every five years | Replacement planning around a shorter service life |
| Other tanks | Shell and bottom thickness tests with interior, exterior and foundation inspection | Every five years | Thickness monitoring locations marked at fabrication |
The report is kept for the life of the tank, names the inspector’s qualifications, and sets the next test date. Within 120 days of receiving it, or before an out-of-service tank returns to service if that is later, the owner reviews the findings and documents what repairs will be made and when; a tank that fails its structural integrity standard is emptied and kept empty until it is repaired or replaced. Paul Industries designs new tanks with that cycle in mind and repairs or replaces tanks that an inspection report has flagged.
Underground tanks and the NJ underground storage tank registration
Underground tanks in New Jersey follow the state’s underground storage tank rules, which require the owner or operator to register each regulated tank with NJDEP under N.J.A.C. 7:14B-2.1; a facility that is not properly registered may not receive deliveries. New Jersey underground storage tanks that are regulated include those holding hazardous substances and petroleum products, and non-residential heating oil tanks over 2,000 gallons, and the NJDEP underground storage tank regulations require work on those systems to be done by individuals and firms holding certification under subchapter 13 of the rule.
Many owners now replace a retired underground tank with an aboveground one, where leaks are visible and inspection is direct. Paul Industries designs and builds the aboveground replacement, its containment, overfill protection and piping, and sets the new tank so the old system can be closed out under the underground rules. The aboveground tank then joins the site’s DPCC and SPCC plans.
Storage tanks in New Jersey’s refining and terminal corridor
Storage tanks in New Jersey are concentrated along the Arthur Kill and Kill Van Kull, where refining and bulk liquid terminals serve the New York Harbor market. The Bayway refinery in Linden processes about 258,000 barrels of crude oil a day, and the Kinder Morgan terminal in Carteret lists 280 tanks ranging from 2,000 to 260,000 barrels, about 8.9 million barrels of storage in all. Those are market facts about the state’s tank population, and they explain why API 653 inspections, bottom replacements and tank rebuilds are steady work in Union and Middlesex counties.
Terminal and refinery owners order field-erected API 650 tanks, bottom and annular plate replacements with impermeable bases and leak detection, shell course repairs, new nozzles and fixed or floating roof work. Paul Industries plans those projects around the API 653 inspector’s findings, the 7:1E base and containment requirements, and the hot work permits of an operating site. Connected lines are handled through process piping in New Jersey and field welds through industrial welding services in New Jersey.
Stainless steel tank fabrication, NJ pharmaceutical and food plants
Stainless steel tank fabrication for New Jersey’s pharmaceutical, cosmetic, food and beverage plants is driven by product contact surfaces, cleaning and documentation more than by discharge prevention. Jacketed mix tanks, buffer and media tanks, WFI and purified water storage, CIP supply and return tanks, and holding tanks are built in 304L or 316L with polished interiors, sloped bottoms, sanitary connections and spray devices.
Two New Jersey details still apply. Tanks of acids, caustics or solvents count toward the 20,000-gallon non-petroleum major facility threshold, so a cleaning chemical farm can bring 7:1E into a plant that holds no fuel. And a tank operating above 15 psig, such as a pressure-rated WFI tank or a jacket on steam, is a pressure vessel under the state’s boiler and pressure vessel rules, built and registered as described on pressure vessel fabrication in New Jersey. Among stainless steel tank fabricators, the difference a quality group notices is the turnover file: heat numbers traced to each sheet and nozzle, weld logs, borescope or visual records of internal welds, surface roughness readings and the passivation report. Finished stainless tanks are cleaned and passivated through passivation services in New Jersey, and water storage is designed with the loops on high-purity water systems in New Jersey.
Generator fuel and day tanks for hospitals, campuses and data halls
Generator fuel storage is where many New Jersey hospitals, campuses, office buildings and data halls first meet the spill rules. Double-wall UL 142 belly and day tanks, transfer pumps, level and leak alarms and vent and fill piping are common, and every oil container of 55 gallons or more counts toward the federal 1,320-gallon aboveground threshold. Paul Industries builds and sets the fuel system with its overfill alarms and containment, and documents each container for the site’s SPCC plan.
Flood, wind and anchorage on waterfront sites
Low-lying sites along the Meadowlands, the Arthur Kill, the Raritan and the Delaware River raise a design question that inland sites rarely face: buoyancy. An empty or partly filled shell in standing floodwater can lift off its foundation, so anchorage is sized for flotation as well as wind, and fill and vent openings are set above the expected flood level where the site allows. Paul Industries checks anchorage, nozzle elevations and containment drainage together so the design holds up in a storm surge as well as a dry day.
Field erection on an operating New Jersey site
Field erection on an operating New Jersey site is planned around the foundation, the weather, hot work and the hydrostatic test. A ringwall or slab is checked for level and bearing before the first bottom plate is laid, and the impermeable base and leak detection that 7:1E expects are installed with it, since neither can be added once the floor is welded. Winter welding needs preheat, wind screens and dry consumables, and coating work waits for surface and air temperatures the coating supplier allows, so schedules in North and Central Jersey often front-load shell erection into the warmer months.
Refineries, terminals and chemical plants issue hot work permits daily, require gas testing and fire watches, and close areas during loading or upset conditions, so the erection sequence is written to fit the site’s permit system rather than the reverse. The hydrostatic test needs a water source, a fill rate the foundation can tolerate, settlement readings during filling, and a planned route for the test water afterwards under the site’s discharge permits. Paul Industries plans each of those steps in the erection schedule the owner reviews before steel arrives at the pad.
Repairs, new bottoms and rebuilds after an API 653 inspection
Repairs after an API 653 inspection in New Jersey usually fall into four groups: bottom and annular plate replacement, shell course repairs or replacement, nozzle and manway work, and roof repairs. A new bottom is the moment the 7:1E impermeable base requirement catches an existing tank, so a liner or coated pad and leak detection go in with the new floor. Shell repairs follow the inspector’s remaining thickness calculations, and hot tapping or new nozzles are designed so the tank’s rating holds.
The owner’s 120-day review window under 7:1E-2.16 sets the pace. Paul Industries prices the inspector’s recommendations item by item, separates what keeps the tank in service from what can wait for the next outage, and returns the repaired unit with an updated record so the next inspection starts from accurate data. Tanks that cannot economically be repaired are replaced on the same foundation or a new one.
Storage tank fabrication, New Jersey design inputs
Storage tank fabrication for a New Jersey site starts from the contents, capacity, operating and design conditions, and the site: footprint, containment, foundations, access for delivery and setting, and wind and snow loads on the roof. Shop-built tanks are limited by the size that can move by road under permits, and larger capacities become field-erected tanks built on the foundation. Paul Industries sets those limits with the owner first, then fixes the standard (API 650, UL 142, STI SP001, ASME BPE or ASME Section VIII) and the nozzle, ladder, platform and instrument schedule.
Among steel storage tank fabricators, the useful questions for a New Jersey project are about the paperwork as much as the welding: the construction standard named on the nameplate, the test record, the containment calculation and the inspection access the 7:1E testing schedule will need. Paul Industries hands those over with every tank, and supports the owner’s plan updates with the data.
What does tank fabrication in New Jersey cost?
Tank fabrication in New Jersey costs what capacity, material, standard, finish and site work make it cost: stainless and polished interiors, jackets and agitators, field erection, containment, foundations, overfill instrumentation and removal of an old tank all add to the price, while a standard shop-built carbon steel tank on an existing pad keeps it down. Paul Industries prepares a budget range from comparable tanks once contents, capacity and site conditions are known, and a firm price after the drawings and the site survey.
| Cost driver | Lower cost end | Higher cost end |
|---|---|---|
| Material | Carbon steel with a coating system | 316L, duplex or nickel alloy |
| Construction | Shop-built and delivered complete | Field-erected on a new foundation |
| Interior finish | Mill finish or lined carbon steel | Polished and electropolished product contact surfaces |
| Containment and base | Existing dike with spare volume | New dike, liner, leak detection and coated pad |
| Instruments and overfill | Level indicator for an attended fill | Independent high and high-high switches with pump cutoff |
| Site work | Open access, existing pad | Crane over live equipment, removal of the old unit, hot work limits |
| Contract terms | Private owner | Public owner with prevailing wage and payroll reporting |
Public owners bring the New Jersey Prevailing Wage Act into field work once a municipal contract passes $19,375 or a contract with another public body passes $2,000.
Who provides tank fabrication in New Jersey?
Paul Industries provides tank fabrication in New Jersey for refining, terminal, chemical, pharmaceutical, food and institutional owners across the state. Headquartered at 256 Shore Drive, Kilmarnock, Virginia, and formerly based in northern New Jersey before a period in Pennsylvania, Paul Industries is an East Coast contractor whose tank work reaches every New Jersey county, the rest of the country and overseas plants through its international projects. Among tank welding companies, New Jersey owners find Paul Industries carrying design, fabrication, testing, setting, piping and documentation as one contract.
Tank types, standards and shop versus field construction are explained on the national tank fabrication page, and the headquarters state version is tank fabrication in Virginia. Cleaning before an inspection or repair runs through industrial tank cleaning, and field testing through hydrostatic testing.
Tank fabrication from Paul Industries for New Jersey sites
Paul Industries designs, fabricates, erects, tests, sets, pipes, repairs and replaces storage and process tanks for New Jersey plants and terminals, with supply-only, design-build and complete installation routes. Each tank is built for the containment, overfill and integrity testing requirements of N.J.A.C. 7:1E and handed over with the records the DPCC, DCR and SPCC plans use. See New Jersey for the rest of Paul’s work in the state, and send contents, capacity and site details to request a quote.
Standards referenced: N.J.A.C. 7:1E, Discharges of Petroleum and Other Hazardous Substances · New Jersey Spill Compensation and Control Act · N.J.A.C. 7:14B, Underground Storage Tanks · 40 CFR Part 112 (SPCC) · API 650 · API 653 · API 510 · STI SP001 · UL 142 · ASTM E1067 · ASME Section VIII · ASME BPE
Frequently asked questions
Who fabricates storage tanks for terminals and plants in Linden, Carteret and Bayonne?
Paul Industries fabricates and erects storage tanks for terminals, refineries and chemical plants in Linden, Carteret, Bayonne, Elizabeth, Perth Amboy and the rest of the Arthur Kill corridor. Work includes new API 650 tanks, bottom replacements with impermeable bases, shell repairs and nozzle additions, planned around the API 653 inspector’s findings and the operating site’s hot work rules. Call 201-450-8280 or request a quote.
Who supplies sanitary mix and holding tanks to New Brunswick, Edison and Route 1 plants?
Paul Industries builds stainless process and storage tanks for pharmaceutical, cosmetic, flavor and food plants around New Brunswick, Edison, Piscataway, Somerset and the Route 1 corridor. Tanks are 304L or 316L with polished interiors, sloped bottoms, sanitary connections and spray devices, and they are handed over with material traceability, weld records, surface readings and passivation reports for the plant’s quality group.
Which South Jersey sites, from Camden to Vineland, does Paul Industries build storage for?
Yes. Paul Industries takes tank fabrication, replacement and repair work across South Jersey, including Camden, Paulsboro, Pennsauken, Gloucester County and Vineland. Food processors there order stainless holding and process tanks, while chemical and fuel sites order carbon steel storage with containment and overfill protection built to the state’s discharge prevention rules.
Is there an NJDEP aboveground storage tank registration?
New Jersey’s tank registration rule, N.J.A.C. 7:14B-2.1, is written for underground storage tanks. Aboveground tanks at a major facility are documented in the facility’s DPCC and DCR plans under N.J.A.C. 7:1E, which list each tank with its contents, capacity, containment and testing, and are resubmitted to NJDEP on the renewal cycle. Paul Industries supplies the tank data those plans need.
What do the NJDEP aboveground storage tank regulations require for overfill protection?
Each aboveground tank at a major facility needs an audible or visual high-level alarm at a set level, plus either a high-high pump cutoff on a separate level detector or direct communication between the gauger and the person controlling the fill, such as line of sight or radio. Tanks of 2,000 gallons or less may instead be attended throughout filling.
What are the NJ above ground storage tank regulations for a tank base?
The base of an aboveground tank at a major facility must be impermeable to the stored substance. Existing tanks meet the requirement when they are substantially rebuilt, replaced or receive a new bottom, and must meet it before going back into service. New tanks are built with a liner or coated pad and, for field-erected tanks, leak detection under the floor.
How big must the dike be around a New Jersey storage tank?
Containment must hold at least the volume of the largest tank or container in the area, plus six inches of rainwater where rain can collect, and it must be impermeable. Dikes, berms, curbing, double walls and sumps all qualify. The required volume is calculated from the full diked area, so tank diameter, height and dike layout are designed together.
How long do storage tanks last in New Jersey service?
Service life depends on material, contents, coating and inspection. A well-maintained carbon steel tank on an impermeable base with cathodic protection and regular API 653 inspection can stay in service for decades, with bottoms and coatings renewed along the way, while plastic tanks have shorter lives and five-year inspections. The integrity test report, not age alone, decides when repair or replacement is due.
When is storage tank replacement better than repair?
Replacement usually wins when an inspection shows widespread shell or bottom thinning, when the tank cannot meet the impermeable base or containment requirements without a rebuild, or when the process needs a different capacity or material. Repair suits isolated corrosion, nozzle problems and coating failures on an otherwise sound shell. Paul Industries prices both from the inspection report so the owner compares them directly.
Does a new tank make my site a major facility under the NJ DEP rules?
It can. Add the new tank’s capacity to everything else stored across the site’s contiguous properties: at 200,000 gallons of hazardous substances of all kinds, or 20,000 gallons of hazardous substances other than petroleum, the site becomes a major facility. Paul Industries totals existing and proposed storage at the start of a project so the owner sees the effect before ordering.
Which tank standard should a New Jersey owner specify?
Large field-erected atmospheric tanks follow API 650, shop-built atmospheric steel tanks follow UL 142 or STI construction, product contact tanks follow ASME BPE, and anything above 15 psig is built as an ASME Section VIII pressure vessel. The choice also sets the integrity testing route under N.J.A.C. 7:1E-2.16, so Paul Industries settles it with the owner at the data sheet stage.
Can an underground fuel tank be replaced with an aboveground one in New Jersey?
Yes. Many owners close a regulated underground tank under N.J.A.C. 7:14B and install an aboveground replacement with containment, overfill protection and an impermeable base. Paul Industries designs, builds and sets the aboveground tank and its piping, and the new tank is added to the site’s DPCC and SPCC plans.
Do stainless process tanks fall under New Jersey discharge prevention rules?
Stainless tanks holding water, product or food ingredients do not count toward major facility capacity, but tanks of acids, caustics, solvents and other hazardous substances do. A cleaning chemical tank farm can therefore bring N.J.A.C. 7:1E into a pharmaceutical or food plant. Paul Industries tallies those tanks during design so containment and alarms are built in where the rule applies.
What inspection does a new shop-built tank need before use in New Jersey?
A shop-built tank receives a post-installation test, such as a static head test, before it is placed in service, and new field-erected tanks are tested to the standard they were built to. Paul Industries performs and records that test, and leaves the nameplate, drawings and test record in the tank file that later API 653 or SP001 inspections build on.
What should a request for tank fabrication NJ projects include?
A request moves fastest with the contents and specific gravity, capacity, operating and design pressure and temperature, preferred dimensions, material and finish, nozzle list, agitation or jacket needs, the site plan showing containment and access, and whether an existing tank is being replaced. Photos of the existing tank and its nameplate help with replacements.
Can one contract cover the tank, its setting and its piping?
Yes. Paul Industries offers supply-only, design-build and complete installation, including foundation design input, setting, anchoring, containment, piping, instruments, overfill devices, ladders and platforms, testing and startup. One contract keeps the tank, its connections and its records together for the DPCC, DCR and SPCC plans.
Planning a new or replacement tank at a New Jersey site?
Send the contents, capacity, design conditions, material and a site sketch showing containment and access. Call 201-450-8280 or request a quote.
