Paul Industries is a data center mechanical contractor in South Carolina, building chiller plants, cooling tower yards, chilled water and condenser water piping, coolant distribution piping for liquid-cooled racks, and generator fuel systems on campuses from Berkeley and Dorchester counties to York County and the Upstate. The company is headquartered at 256 Shore Drive, Kilmarnock, Virginia, works the length of the East Coast and takes data hall and campus work in every part of South Carolina. Owners can buy prefabricated racks and skids as a supply-only package, a design-build mechanical package, or complete installation through start-up.

Request a quote or call 201-450-8280

Headquarters 256 Shore Drive, Kilmarnock, Virginia
Exempt purchases Computer-room cooling under S.C. Code 12-36-2120(79)
Exemption thresholds $50M invested and 25 jobs within five years
Santee Cooper large loads 50 MW and up, 15-year contract (April 2025)
Mechanical code 2021 SC Mechanical Code, in force since January 1, 2023
Industrial power 6.84 cents/kWh in 2024; US average 8.13 (EIA)
Reviewed November 2026

What does a data center mechanical contractor in South Carolina build?

A data center mechanical contractor in South Carolina builds the systems that move heat from the computer rooms to the outdoors: chillers and their pumps, cooling towers or dry coolers, the yard piping that ties them together, the risers and loops that feed air handlers and coolant distribution units, and the controls and instruments that keep each loop in balance. On most campuses the same package also carries the diesel fuel piping to generators, domestic and fire water service entries, and the condensate and drainage systems around the hall.

The work on a South Carolina campus is shaped by four things a national scope sheet leaves out. The first is the state sales tax exemption, which names cooling equipment and sets a design test the plant must pass. The second is a set of 2026 county pauses on new data center approvals. The third is the large-load contract terms the state’s utilities now require. The fourth is the climate, which runs hot and humid from the coast to the Midlands. The general method for the trade is set out on the national data center mechanical contractors page; this page goes into what changes when the campus sits in South Carolina.

Where are data centers in South Carolina, and how many are being built?

Large data centers in South Carolina cluster in three corridors: the Lowcountry west of Charleston in Berkeley and Dorchester counties, the York County edge of the Charlotte region near Rock Hill and Clover, and Aiken County on the Savannah River side of the Midlands. Smaller colocation and enterprise sites sit in Columbia, Greenville, Spartanburg and Charleston. Asked how many data centers are in South Carolina, published counts differ by what they include, so the clearer measure for a contractor is the announced campus investment, which now runs to many billions of dollars.

An early large data center South Carolina landed was Google’s Berkeley County campus at the Mount Holly Commerce Park in Moncks Corner, which opened in 2007 as the company’s first site in the state. In September 2024 Google announced $3.3 billion for that campus and two new Dorchester County campuses at Ridgeville (Pine Hill Business Campus) and St. George (Winding Woods Commerce Park); in October 2025 it announced a $9 billion statewide expansion that includes the same sites. Every Google South Carolina data center campus described in those announcements sits within the Charleston region’s industrial belt.

QTS announced its first South Carolina campus in York County in September 2023, and the company now describes nine buildings in three phases with an investment of about $8 billion. The Meta data center South Carolina officials announced in August 2024 is an $800 million, 715,000 square foot building in the Sage Mill Industrial Park in Aiken County, planned for about 200 megawatts and paired with a 100 megawatt solar farm. These are market facts about the South Carolina data center market, named here to show where demand sits.

South Carolina data center corridors and what each asks of the mechanical package
CorridorAnnounced campuses (market facts)Site conditionsMechanical emphasis
Berkeley and Dorchester counties (Moncks Corner, Ridgeville, St. George)Google campuses at Mount Holly, Pine Hill and Winding WoodsCoastal plain heat and humidity, hurricane exposure, low-lying sitesEquipment anchorage and elevation, corrosion-resistant coatings, high latent load on make-up air
York County (Rock Hill, Clover)QTS campus, nine buildings in three phasesPiedmont terrain, Charlotte-region labor and supply marketRepeatable prefabricated racks and skids for phased buildings
Aiken County (Graniteville)Meta building in the Sage Mill Industrial ParkMidlands summer heat; cooperative power supplyPlant efficiency against a fixed power allocation; dry heat rejection options
Columbia and the MidlandsEnterprise and colocation hallsHottest summer normals in the state’s interiorRetrofits inside operating buildings, chiller upgrades, added liquid cooling
Greenville and Spartanburg (the Upstate)Colocation and corporate sitesCooler nights, more economizer hours than the coastWaterside economizers, freeze protection on yard piping

Are data centers being built in South Carolina in 2026?

Data center construction in South Carolina continued through 2026 on campuses already approved, while new applications slowed in several counties that paused approvals to write their own rules. For a mechanical contractor the result is a two-speed market: phased builds on approved sites keep ordering chillers, pumps and piping, and greenfield proposals in paused counties wait on zoning before equipment can be released.

How does the South Carolina data center sales tax exemption treat cooling equipment?

The South Carolina data center sales tax exemption in S.C. Code 12-36-2120(79) covers computer equipment used within a qualifying datacenter, and the statute’s definition of computer equipment expressly includes cooling apparatus and “equipment cooling systems for managing the performance of the datacenter property, including mechanical and electrical equipment.” Chillers, pumps, coolant distribution units and the piping that serves the computer equipment therefore sit inside the definition, while electricity used for comfort air conditioning in offices and other support spaces stays taxable.

The exemption comes with a design test. A facility qualifies as a datacenter only if its power and cooling systems are concurrently maintainable, with redundant capacity components and multiple distribution paths serving the computer equipment, although a single path may carry the load at any one time. That language reads like a mechanical specification: every chiller, pump and heat exchanger must be serviceable on a planned basis without interrupting the computer equipment, which means isolation valves, bypasses, cross-connections and spare capacity drawn into the piping design from the start.

What S.C. Code 12-36-2120(79) requires, and what each element means for the mechanical package
Element of the exemptionWhat the statute saysEffect on the mechanical scope
Equipment coveredComputer equipment, including cooling apparatus and equipment cooling systems with mechanical and electrical equipmentPurchase records separate cooling equipment serving the computer rooms from equipment serving offices and support areas
Facility designConcurrently maintainable power and cooling, redundant capacity components, multiple distribution pathsValving, loop configuration and redundancy proven on drawings and in functional tests
InvestmentAt least $50 million by one taxpayer, or $75 million in aggregate by more than one, over five yearsMechanical capital counts toward the total; schedules tied to the five-year window
JobsAt least 25 full-time jobs at 150 percent of the state or county per capita income, whichever is lower, kept for three consecutive yearsOperations staffing plans include mechanical maintenance positions
Notice and certificationWritten notice to the Department of Revenue and Department of Commerce starts the five-year clock; certification by CommerceEquipment purchases timed after notice so they can be claimed
Later purchasesReplacement equipment and future expansions also qualifyChiller replacements and added cooling for denser racks fall under the same exemption
Missed targetsThe Department of Revenue may assess the sales or use tax on exempted purchasesOwners keep clean records of what each exempt item serves

The South Carolina data center incentives have drawn legislative attention. A 2026 act, H.5122, created a new sales tax exemption for internet access and communications providers and expressly bars data centers of 50 megawatts or more that become electric customers after December 31, 2026 from using it. The datacenter exemption in item (79) itself remained in the code as fetched for this page. Paul Industries prices mechanical packages so the owner’s tax advisers can see which line items serve the computer equipment and which serve support spaces.

South Carolina data center moratorium decisions and the mechanical schedule

A South Carolina data center moratorium is, in 2026, a county or town decision rather than a state one: without statewide siting rules, councils paused new approvals to write their own standards. Jasper County approved a one-year moratorium covering applications, permits, rezonings and incentives for data centers, Colleton County adopted a six-month pause, Laurens County voted for a one-year pause, and the Town of Mount Pleasant finalized a two-year pause. Other councils, including York, Chester, Spartanburg and Orangeburg, took first votes or considered similar measures during the year.

For the mechanical package a pause changes procurement more than design. Chillers, large pumps and switchgear carry long lead times, and an owner who releases them before zoning is final carries the risk of equipment with no site. Paul Industries works with owners on staged releases: design and shop drawings proceed, long-lead equipment is reserved against a release date, and prefabricated racks and skids are built only once the permit path is clear. Campuses already approved before a pause, and work inside existing halls, generally carry on under their existing approvals.

South Carolina data center legislation to watch

South Carolina data center legislation filed in 2026 included H.5215, the Ratepayer Protection and Large Load Customer Infrastructure Accountability Act, introduced on February 19, 2026 to keep large-load customers’ incremental costs off other customer classes, and a separate House bill that would bar final approval of data center projects until 2028. Neither had become law in the sources reviewed for this page. The practical rule for a mechanical schedule is to tie major purchases to signed utility agreements and final zoning, whatever the statute books say.

How do Santee Cooper, Dominion Energy and Duke Energy terms shape the cooling plant?

Utility contract terms shape the cooling plant in South Carolina because a large campus now buys a fixed power allocation under long commitments, and every kilowatt the mechanical plant draws is a kilowatt the computer equipment cannot use. Santee Cooper’s board approved a large-load rate in April 2025 for customers needing 50 megawatts or more, with a 15-year contract and a minimum payment to exit, adopted as a four-year experiment. Dominion Energy South Carolina told lawmakers in 2026 that it uses long-term service agreements, minimum billing and termination fees for large customers, and the Duke Energy utilities and the cooperatives serve other parts of the state.

Under those terms the mechanical design target is the ratio of cooling power to computer power across the year, not only at the summer peak. Paul Industries prices plant options against the owner’s allocation: higher chilled water and coolant temperatures that let chillers run at lower lift, water-side economizers that cut compressor hours in the Upstate’s cooler months, variable-speed pumps sized to the actual load profile, and liquid cooling that moves rack heat into water at temperatures where dry coolers can reject it. Industrial electricity in South Carolina averaged 6.84 cents per kilowatt-hour in 2024 against a national 8.13 (EIA), so the case for efficiency on a power-capped campus rests on capacity more than on the bill.

Cooperatives matter too. The Meta building in Aiken County is served through Central Electric and Aiken Electric Cooperative, with a dedicated solar farm, which shows that the utility answer differs by site and that the mechanical plan should start from the actual service agreement.

Heat, humidity and storms: designing yard equipment for South Carolina

South Carolina summers load a data center cooling plant hard: Columbia’s July normals are a 95 degree Fahrenheit high and a 73 degree low (NOAA, 1991 to 2020), and the coastal counties add humid nights that keep the wet bulb high. Cooling towers lose approach on those nights, air-cooled chillers lose capacity as the dry bulb climbs, and make-up air units carry a large moisture load before any heat from the servers is counted.

On Lowcountry sites the yard also faces salt air and hurricane winds. Coil coatings, stainless or coated fasteners and sealed electrical enclosures extend equipment life near the coast. Anchorage for chillers, towers, dry coolers and pipe racks is designed to the wind provisions of the building code in force, and equipment pads on low-lying sites are set with drainage and flood elevation in mind. In the Upstate, colder winter nights bring freeze protection into the design: glycol in exposed loops, heat tracing on small lines and drain points on yard headers. The Midlands sit between the two and get some of each.

Which codes, permits and license rules apply to the mechanical scope?

The codes for a South Carolina data center’s mechanical scope are the 2021 South Carolina Building, Mechanical, Plumbing, Fuel Gas and Fire codes, which are the 2021 International Codes with state modifications, in force since January 1, 2023 and enforced by every municipality and county. The state energy code remains the 2009 International Energy Conservation Code. The Building Codes Council has moved toward the 2024 editions, with its modifications published in the State Register on May 22, 2026, so the edition in force on a given permit is confirmed with the jurisdiction when drawings are submitted.

South Carolina rules that touch a data center mechanical package
RequirementSourceWhat it covers on a campus
Mechanical, plumbing, fuel gas and fire codes2021 South Carolina codes, enforced by counties and municipalities (S.C. Code 6-9-50)Permits and inspections for HVAC, piping, fuel gas and fire protection
Energy code2009 International Energy Conservation CodeMinimum equipment efficiencies and controls for the building
Contractor licensingS.C. Code 40-11-30 and 40-11-410Mechanical work above $10,000 is performed under a state license in the matching classification, such as Air Conditioning or Pressure and Process Piping
BoilersSouth Carolina Boiler Safety Act, Title 41 Chapter 14Registration and inspection of boilers on the campus; pressure vessels are exempt under 41-14-60(C)
Underground fuel tanksSCDES R.61-92 (adopting 40 CFR Part 280)Registration, release detection and corrosion protection for underground diesel tanks, including those feeding emergency generators
Generator air permitsSCDES R.61-62Air permit review for the generator fleet and its run hours
Large water withdrawalsS.C. Code Title 49 Chapter 4 and R.61-119Permits for surface water withdrawals above 3 million gallons in any month

Since July 1, 2024, the environmental permits once issued by DHEC come from the South Carolina Department of Environmental Services, so tank registrations and air permits on older campuses carry the former agency’s name until renewal. Piping inside the plant follows ASME B31.9 for building services or ASME B31.1 where steam or higher-pressure service requires it, with pressure testing, flushing and cleaning recorded before any loop is turned over.

Do chilled water vessels fall under the South Carolina Boiler Safety Act?

Chilled water vessels fall outside the state program: the South Carolina Boiler Safety Act covers boilers, requires new boilers to be registered with the National Board, and states in 41-14-60(C) that all pressure vessels are exempt from regulation under the chapter. Expansion tanks, air and dirt separators and buffer tanks are still built to ASME Section VIII where their size and pressure call for it, and the owner’s insurer usually inspects them, but they carry no state certificate. Hot water boilers serving office heating on a campus remain under the act.

Water, cooling towers and closed loops on South Carolina campuses

Water planning for a South Carolina data center starts with the cooling choice: an evaporative plant draws make-up water continuously in summer, while a closed-loop plant with dry coolers or air-cooled chillers uses little water after the initial fill. The state regulates surface water withdrawals above 3 million gallons in any month under Title 49, Chapter 4, and most campuses buy water from a utility rather than withdraw it, so the practical limits are the utility’s allocation and the county’s view of the project. Several of the 2026 county pauses cited water and infrastructure studies among their reasons.

Paul Industries builds both routes. On evaporative plants the scope includes towers, basin heaters where freeze risk exists, side-stream filtration, chemical feed and the blowdown piping to sewer. On closed-loop plants it includes dry coolers or air-cooled chillers, glycol management where freeze protection is needed, and larger heat exchange surface to make up for the higher approach. The choice for each campus is set out in more depth on the data center cooling systems in South Carolina page, and rack-level cooling loops are covered on the data center liquid cooling in South Carolina page.

Generators, fuel and drainage around the hall

Generator fuel systems on a South Carolina campus are mechanical work with environmental rules attached: underground diesel tanks register with SCDES under R.61-92, which since 2017 requires release detection on tanks that feed emergency generators, and the generator fleet itself needs air permit review under R.61-62. Many campuses use aboveground belly tanks under each generator, with day tanks, transfer pumps and polishing systems on larger fleets.

Paul Industries installs the fuel supply and return piping, transfer and polishing skids, tank level and leak monitoring, and the vent and fill connections, and pressure tests each line before fuel is introduced. Around the hall, condensate from air handlers and coolant distribution units is collected and routed to drains or reuse, and storm drainage for equipment yards is coordinated with the civil design so that spill containment at fuel stations does not route to storm sewers.

How is data center construction in South Carolina phased on the mechanical side?

Data center construction in South Carolina is usually phased building by building, and the mechanical package is phased with it: the central plant or yard for the first building is sized for later expansion, headers are built with valved stubs for future connections, and each later hall ties in without shutting down the halls already in service. A campus such as the nine-building QTS plan in York County illustrates the pattern, with the same mechanical design repeated across phases.

Repetition is what makes prefabrication pay. Paul Industries prefabricates pipe rack modules, pump skids and coolant distribution manifolds off site, tests them and delivers them sequenced to the building schedule, which shortens the time crews spend in a building that is also full of electrical work. Tie-ins to an operating plant follow a written method of procedure, with redundancy confirmed before any valve is closed. Commissioning steps for each phase are covered on the data center commissioning in South Carolina page.

How long does it take to build a data center’s mechanical systems?

How long does it take to build a data center depends far more on power delivery and equipment lead times than on installation hours. Mechanical installation on a single hall typically runs over many months once equipment arrives, and chillers, large pumps and switchgear can take a year or more to arrive after release. Owners shorten the schedule by fixing the mechanical design early enough for prefabrication, releasing long-lead equipment as soon as zoning and power agreements allow, and repeating a proven design from one building to the next.

Data center construction requirements beyond the code book

Data center construction requirements on a South Carolina campus include the owner’s own standards, which usually go further than the code. Typical requirements cover redundancy levels for chillers and pumps, welded or grooved joints by service, cleanliness and flushing standards for coolant loops that feed liquid-cooled racks, materials compatible with propylene glycol and treated water, and the ASHRAE TC 9.9 thermal envelope the plant must hold. Many owners also specify how valves are tagged, how sensors are named in the controls, and what records are turned over.

Welding records and inspection results matter more on liquid-cooled halls, where a weld defect in a coolant line can put water near energized equipment. Weld procedures, welder qualifications and examination records for those lines are covered on the industrial welding services in South Carolina page, and the plant piping itself on the process piping in South Carolina page.

Who installs data center mechanical systems in South Carolina?

Paul Industries installs data center mechanical systems in South Carolina: chillers, cooling towers and dry coolers, pumps and heat exchangers, chilled water, condenser water and coolant distribution piping, generator fuel systems, controls integration and the testing that proves each loop before turnover. Paul Industries is headquartered at 256 Shore Drive, Kilmarnock, Virginia, was formerly based in northern New Jersey, then Pennsylvania, and takes work in all 50 states, so an owner with campuses in South Carolina and neighboring states can use one contractor for all of them.

Owners in the headquarters state will find the Virginia version of this work on the data center mechanical contractor in Virginia page, and the neighboring North Carolina data center mechanical contractor page covers the Catawba Valley and Charlotte campuses across the state line from York County. The wider regional picture is on the Southeast page.

What does data center mechanical work in South Carolina cost?

Data center mechanical cost in South Carolina is driven by the cooling design, the redundancy level, the share of liquid cooling, the number of phases and the equipment market at the time of release, so any honest number starts from the owner’s basis of design. How much does it cost to build a data center’s mechanical plant is answered per project: chillers, towers or dry coolers and pumps usually form the heaviest equipment line, ahead of yard and hall piping, controls, and fuel systems.

What moves the price of a South Carolina data center mechanical package
Cost driverLower-cost directionHigher-cost direction
Heat rejectionEvaporative towers where water is availableDry coolers or air-cooled chillers sized for coastal summer peaks
RedundancyN+1 chillers and pumps on a single loopConcurrently maintainable dual paths throughout, as the exemption’s design test describes
Rack coolingAir cooling with containmentLiquid-cooled racks with coolant distribution units and secondary loops
PhasingOne building, one plantMultiple buildings with oversized headers and live tie-ins
PrefabricationRepeated modules across phasesOne-off field-built piping on a congested site
SiteInland, high groundCoastal salt exposure, elevated pads and hurricane anchorage

Two South Carolina facts help the budget. The state has no prevailing wage law, so private campus work is priced on market labor rates, with federal Davis-Bacon rates only where federal funds are involved. And cooling equipment serving the computer rooms can fall under the sales tax exemption once the facility qualifies. Paul Industries gives a budget range from comparable scope early, then a firm price once the basis of design, phasing and equipment list are set.

Data center mechanical work from Paul Industries in South Carolina

Paul Industries designs, prefabricates, supplies, installs, tests and starts up data center mechanical systems across South Carolina, from chiller plants and yard piping to coolant distribution loops and generator fuel systems, and services them after handover. Related South Carolina pages cover chiller repair in South Carolina for operating plants, and the South Carolina overview lists the other process and utility systems Paul builds in the state. Send drawings, a basis of design and the phasing plan, and request a quote for the next hall or campus.

Standards referenced: S.C. Code 12-36-2120(79) datacenter sales and use tax exemption · 2021 South Carolina Mechanical Code (2021 International Mechanical Code with SC modifications) · 2021 South Carolina Building, Plumbing, Fuel Gas and Fire Codes · 2009 International Energy Conservation Code (South Carolina energy code) · S.C. Code Title 40 Chapter 11 (contractor licensing) · South Carolina Boiler Safety Act, S.C. Code Title 41 Chapter 14 · SCDES R.61-92 Underground Storage Tank Control Regulations (40 CFR Part 280) · SCDES R.61-62 Air Pollution Control Regulations and Standards · S.C. Code Title 49 Chapter 4 and R.61-119 (surface water withdrawal) · ASME B31.9 · ASME B31.1 · ASHRAE TC 9.9 thermal guidelines

Frequently asked questions

Which contractor builds data center mechanical systems in Berkeley County, Moncks Corner and Goose Creek?

Paul Industries builds data center mechanical systems in Berkeley County, including the Moncks Corner and Goose Creek areas, as an East Coast contractor headquartered in Kilmarnock, Virginia. Lowcountry sites call for corrosion-resistant yard equipment, hurricane anchorage and make-up air sized for humid nights. Paul Industries installs chiller plants, towers or dry coolers, yard and hall piping and fuel systems, and ties new halls into operating plants under a written method of procedure.

Does Paul Industries take data center mechanical work in Ridgeville, St. George and Dorchester County?

Yes. Paul Industries takes data center mechanical work in Ridgeville, St. George and the rest of Dorchester County, where Google announced two new campuses in 2024. Paul Industries prefabricates pipe rack modules and pump skids for phased buildings, installs and tests the plant, and provides the turnover records an owner’s operations team needs. Send the basis of design and phasing plan to start pricing.

Who handles mechanical work for a data center in York County, South Carolina, near Rock Hill and Clover?

Paul Industries handles mechanical work for a data center in York County, South Carolina, including campuses near Rock Hill and Clover. York County sits at the edge of the Charlotte region, so owners often run campuses on both sides of the state line. Paul Industries works in both states, which lets one contractor carry the same mechanical design, prefabricated modules and testing standard across every building.

Does Paul Industries build cooling plants for data centers in Aiken County and the Savannah River area?

Paul Industries builds cooling plants, coolant distribution piping and generator fuel systems for data centers in Aiken County, Graniteville and the wider Savannah River area. Midlands summers are hot, and campuses there often buy power through cooperatives under fixed allocations, so Paul Industries prices plant options by their annual power draw as well as their capital cost.

Who builds mechanical systems for data centers in Greenville, South Carolina, and in Spartanburg?

Paul Industries builds and upgrades mechanical systems for data centers in Greenville, South Carolina, and for data centers in Spartanburg, South Carolina, across the Upstate. Many Upstate sites are colocation and corporate halls inside operating buildings, so the work is often a chiller upgrade, added liquid cooling or a new loop tied in live. Cooler Upstate winters favor water-side economizers, which cut compressor hours.

Does Paul Industries work on data centers in Columbia, South Carolina?

Paul Industries works on data centers in Columbia, South Carolina, and the Midlands, including enterprise halls, colocation sites and government computer rooms. Columbia’s July normals reach a 95 degree high, so chiller capacity at peak and condenser water performance on hot afternoons decide many retrofit plans there. Paul Industries replaces chillers, adds capacity and installs liquid cooling while the hall stays in service.

How many data centers are in South Carolina, and where are the new ones going?

Published counts of data centers in South Carolina differ by what they include, from small enterprise rooms to hyperscale campuses. New data centers in South Carolina are concentrated in Berkeley and Dorchester counties near Charleston, York County near Rock Hill, and Aiken County near Graniteville, with smaller colocation sites in Columbia, Greenville and Spartanburg. Several counties paused new approvals in 2026 while they wrote siting rules.

Does the South Carolina datacenter exemption cover chillers, cooling towers and pumps?

The statute’s definition of computer equipment includes cooling apparatus and equipment cooling systems for managing the performance of the datacenter, including mechanical and electrical equipment, so chillers, pumps and cooling equipment serving the computer rooms fall within it for a qualifying facility. Electricity for comfort air conditioning in offices stays taxable. Paul Industries itemizes quotes so the owner’s tax advisers can separate exempt and taxable lines.

What happens if a data center misses the South Carolina exemption's investment or job targets?

If a taxpayer claims the exemption but does not meet the $50 million investment (or $75 million aggregate) and 25-job requirements by the end of the five-year period, the Department of Revenue may assess the sales or use tax on the items purchased. If jobs later fall below the required level, the exemption on equipment purchases stops until the job count is restored. Clear purchase records make either review simpler.

Which South Carolina counties paused data center approvals in 2026?

Jasper County approved a one-year moratorium, Colleton County adopted a six-month pause, Laurens County voted for a one-year pause, and Mount Pleasant finalized a two-year pause, with York, Chester, Spartanburg, Orangeburg and Beaufort considering or advancing similar measures. Pauses apply to new applications and approvals, so projects already approved and work inside existing halls generally continue.

How does a county pause change when chillers and pumps should be ordered?

A pause moves the release of long-lead equipment later, because an owner who buys chillers before zoning is final risks equipment with no site. Paul Industries keeps design and shop drawings moving, reserves production slots for chillers and large pumps against a target release, and starts prefabrication of racks and skids once the permit path is clear, so the schedule recovers quickly when approval comes.

Does Santee Cooper's large-load rate affect the mechanical design?

Santee Cooper’s large-load rate, approved in April 2025 for customers needing 50 megawatts or more, ties a campus to a 15-year contract with a minimum payment, so the power allocation is fixed long before the plant runs. Every kilowatt the cooling plant uses comes out of that allocation. Paul Industries compares chiller, economizer and liquid cooling options by annual cooling power as well as first cost.

Do underground diesel tanks for data center generators need leak detection in South Carolina?

Underground diesel tanks feeding emergency generators need release detection under SCDES regulation R.61-92, which adopted the federal underground tank rules in 2017 and removed the earlier exemption for emergency generator tanks. Tanks are registered with the department and fitted with leak monitoring and corrosion protection. Paul Industries installs the tanks’ piping, monitoring and transfer systems and tests them before fuel is delivered.

Does South Carolina have a prevailing wage requirement for private data center construction?

South Carolina has never enacted a state prevailing wage law, so private data center construction is priced on market labor rates. Federal Davis-Bacon rates apply only where federal funding is involved. That makes the mechanical labor budget more predictable than in states with state wage schedules, and Paul Industries prices South Carolina packages on that basis.

Which South Carolina mechanical license classification covers chilled water piping?

South Carolina divides mechanical contracting into subclassifications under S.C. Code 40-11-410, including Air Conditioning, Heating, Plumbing, Refrigeration and Pressure and Process Piping. Comfort heating and air conditioning piping falls under the air conditioning and heating classifications, while process piping systems fall under Pressure and Process Piping. A state license is required for mechanical work whose total cost is greater than $10,000.

How long does a South Carolina data center take from groundbreaking to cooling start-up?

The span from groundbreaking to cooling start-up on a single South Carolina hall is usually set by power delivery and chiller lead times rather than by installation. Mechanical installation runs over many months once equipment arrives, and commissioning follows in steps from individual pumps to the full plant under load. Repeating a proven design across phases shortens every building after the first.

What does it cost to build the mechanical plant for a South Carolina data center?

The cost of a South Carolina data center’s mechanical plant depends on heat rejection type, redundancy, the share of liquid-cooled racks, phasing and the equipment market at release, so it is priced from the basis of design. Paul Industries gives a budget range from comparable scope early and a firm price once the equipment list, phasing and site conditions are set.

What documents start a South Carolina data center mechanical estimate with Paul Industries?

Useful documents are the basis of design, mechanical drawings at whatever stage they are, the equipment schedule, the phasing plan, the redundancy standard, and any owner specifications for welding, cleanliness and turnover records. For liquid-cooled halls, include the rack heat loads and coolant temperatures. Send them to Paul Industries at 201-450-8280 or through the quote request form.

Planning a South Carolina data center hall or campus?

Send the basis of design, mechanical drawings, equipment schedule and phasing plan. Call 201-450-8280 or request a quote.