Paul Industries provides chiller repair in Texas, diagnosing and repairing centrifugal, screw, scroll and air-cooled chillers at refineries, chemical and food plants, hospitals, campuses and data centers from Houston and Dallas-Fort Worth to San Antonio, Austin and West Texas. Texas machines run long, hot seasons, face freezes that crack evaporators, and in ERCOT territory carry summer peaks that set next year’s transmission charges. When a machine has reached the end of sensible repair, Paul Industries supplies and installs its replacement as well as handling every overhaul and retrofit short of that.

Request a quote or call 201-450-8280

Headquarters 256 Shore Drive, Kilmarnock, Virginia
Summer load July normals: Dallas 97 F / 78 F, Houston 93 F / 77 F (NOAA)
Freeze benchmark DFW reached -2 F on February 16, 2021 (NWS)
EPA leak rule Applies from 2026 to chillers holding 15 lb or more of HFC
Industrial power 6.12 cents/kWh against a US 8.13 (EIA, 2024)
Reviewed November 2026

What does chiller repair in Texas involve?

Chiller repair in Texas involves the same core work as anywhere, fault diagnosis, refrigerant leak repair, compressor and motor work, tube cleaning and testing, controls and starter repair, but Texas conditions decide which faults turn up most and when repairs can be scheduled. Long run seasons, spring through late autumn, wear compressors and foul condenser tubes; humid Gulf air and industrial atmospheres corrode coils; hard freezes split evaporator tubes; and grid events trip machines that then have to restart cleanly.

Symptom-by-symptom diagnosis for any chiller sits on the national chiller repair page. Texas owners face a further set of conditions, and those are the subject here: the climate data behind their run hours, freeze damage, refinery and petrochemical atmospheres, summer peaks and thermal storage, the state’s licensing and code rules for chiller work, and the repair or replace decision at Texas power prices.

How Texas heat and humidity load a chiller

Texas heat loads a chiller hard because July normal highs reach 93 to 97 degrees Fahrenheit across the state’s main cities, nights stay warm, and along the Gulf the air holds enough moisture that latent load keeps machines running after sunset. NOAA’s 1991 to 2020 normals put Dallas at a 97 degree July high and a 78 degree low, and Houston at 93 and 77, with Houston’s annual afternoon humidity averaging 55 percent.

Texas regions and the chiller faults their conditions tend to produce
RegionConditions (NOAA July normals)Common chiller problemsRepair and service emphasis
Houston, Pasadena, Baytown and the Ship Channel93 F / 77 F; humid; industrial atmosphereCoil and cabinet corrosion, condenser fouling, electrical enclosure corrosionCoil inspection and coating, tube cleaning, enclosure sealing, leak checks at corroded joints
Beaumont, Port Arthur and Corpus Christi94 F / 76 F (Corpus Christi); humid, salt and refinery airAccelerated corrosion on air-cooled units; process chiller wearCoated or replacement coils; repairs timed to turnarounds
Dallas-Fort Worth and North Texas97 F / 78 F (Dallas); hard freezes in some wintersHigh head pressure on hot afternoons; freeze-split evaporators and coilsCondenser and tower performance; winter layup and glycol
Austin and San Antonio97 F / 75 F in Austin, 95 F / 75 F in San AntonioLong run hours, scale from hard makeup waterTube cleaning, eddy current testing, tower water treatment
El Paso, Midland and the Panhandle96 F / 73 F (El Paso, Midland); 93 F / 66 F (Amarillo); dryDust-loaded condenser coils; freeze risk on the plainsCoil cleaning, fan and motor checks, freeze protection
Rio Grande Valley95 F / 78 F (Brownsville); humidNear year-round operation; coil corrosion near the coastOverhauls planned into the short cool season

A warm night is what separates Texas from cooler cooling markets. A 78 degree Dallas July low gives a centrifugal chiller no relief overnight, so lift stays high around the clock in midsummer, and every fouled tube, weak tower fan or high condenser water setpoint shows up as higher compressor power and closer approach to surge.

What the February 2021 freeze did to Texas chillers

The February 2021 freeze damaged Texas chillers because it brought days of subfreezing temperatures to equipment designed for a warm climate, and it arrived with grid outages that stopped the pumps and heaters meant to protect it: Dallas-Fort Worth fell to minus 2 degrees Fahrenheit on February 16, Waco stayed below freezing for 205 consecutive hours, and ERCOT shed up to 20,000 megawatts of load. Water standing in idle evaporators, air-cooled condenser coils and outdoor piping froze and split.

A freeze-split evaporator is a serious repair, because a broken tube can let water into the refrigerant circuit. Paul Industries repairs freeze damage in a set order: isolate and drain the machine, pressure test the refrigerant side and the water side separately to find every failed tube, check refrigerant and oil for moisture, plug or replace damaged tubes after eddy current testing shows the condition of the rest of the bundle, dehydrate the circuit with deep vacuum if water entered, replace oil, filter driers and refrigerant as needed, and test the machine under load before it returns to service.

Prevention costs far less than the repair. Machines that can sit idle in winter are drained or protected with glycol, outdoor piping is heat traced and insulated, heat trace and crankcase heaters are put on circuits that stay energized during a grid emergency, and chilled water pumps are sequenced to keep water moving through exposed sections when temperatures fall.

Industrial chiller repair on refinery and petrochemical sites

Industrial chiller repair on refinery and petrochemical sites along the Houston Ship Channel, in Beaumont and Port Arthur, and around Corpus Christi differs from building work because the machines serve processes, sit in corrosive and sometimes classified areas, and can be taken down only on the plant’s schedule. Process chillers cool reactor jackets, condensers, lab and analyzer systems and control rooms, and a failure can limit production rather than comfort.

Work inside those plants follows the owner’s safety programs, permits to work and turnaround planning. Paul Industries plans repairs into scheduled outages or turnarounds where possible, brings likely parts for the planned window, and repairs coils, compressors and controls with materials suited to the atmosphere, such as coated coils and sealed enclosures where hydrogen sulfide, chlorides or acid vapors attack copper and aluminum. Plant-wide outage work is described on shutdown and turnaround services, and machines that serve a single process on process chillers.

Thermal storage, summer peaks and when to repair

Summer peaks matter to Texas chiller owners inside ERCOT because transmission costs there are allocated by each customer’s demand during the summer’s four coincident 15-minute peaks, which fall one per month from June to September, and a chiller plant is often a major controllable load on the site. A machine that is out of service in July, forcing a less efficient unit to run during a peak interval, can raise the following year’s transmission charges as well as the current bill. The Public Utility Commission is reviewing that method, but while it applies, repairs belong in the spring and autumn wherever the load allows.

Thermal storage changes the picture at big district and campus plants. The Texas Medical Center’s district energy plant in Houston, for example, uses a stratified chilled water tank of about 8.8 million gallons and chillers as large as 8,000 tons to make cooling at night and carry afternoon load from storage. Paul Industries repairs chillers at plants with storage by scheduling the work when the tank can carry the shortfall, and at plants without storage by confirming spare capacity for the hottest expected hours of the outage. Storage plants also bring their own repair work: tank diffusers, stratification sensors and the valves that switch the plant between charging and discharging all need checking, and a chiller that charges the tank overnight has to hold its leaving water temperature tightly, so its controls and approach temperatures get extra attention during service.

Refrigerant rules that shape Texas chiller repairs

Refrigerant rules shape Texas chiller repairs through three federal programs under the AIM Act: falling HFC supply caps, global warming potential limits for newly installed machines, and the 2026 leak repair obligations for systems charged with 15 pounds or more of an HFC. Older HCFC machines sit under the separate phaseout of R-22 and R-123.

Refrigerant in a Texas chiller and how it changes the repair plan
ChargeWhere Texas owners find itFederal statusRepair planning
R-22Older screw, scroll and reciprocating unitsProduction and import ended January 1, 2020; reclaimed supply onlyRepair for a short horizon; price retrofit or replacement alongside
R-123Low-pressure centrifugal chillersImport allowances end in 2030; recovered and reclaimed supply after thatLeak tightness and purge condition protect the remaining charge
R-134aCentrifugal and screw chillersHFC caps tighten in 2029 and 2036; leak rule applies at 15 pounds or moreFully repairable; leak rate records kept with each addition
R-410AScroll and smaller air-cooled chillersNew comfort chillers limited to GWP below 700 since January 1, 2025Repairable; a replacement uses a lower-GWP refrigerant
Low-GWP HFOs and blendsRecent installationsMeet new-equipment limitsTechnicians follow the refrigerant’s safety class and handling rules

The 2026 leak rule works on a running calculation: every top-up triggers a leak rate figure, and the trigger points are 10 percent a year for comfort cooling, 20 percent for commercial refrigeration and 30 percent for industrial process refrigeration. Past its trigger, a machine has 30 days for repair, stretched to 120 when fixing it means shutting down an industrial process, and the fix is proven with an initial and a follow-up verification test. On the new-equipment side, process chillers whose leaving fluid stays at minus 30 degrees Celsius or warmer joined the refrigerant limits at the start of 2026, a date Gulf Coast plants planning replacements need on their calendars. Paul Industries keeps the leak rate calculation, repair record and verification tests together in the owner’s file.

Texas licensing and code rules for chiller work

Chiller work in Texas falls under two sets of rules: state licensing law for air conditioning and refrigeration contracting, and the mechanical code of the city where the machine sits. Chapter 1302 of the Occupations Code, enforced by TDLR, splits environmental air conditioning into a Class A endorsement with no size cap and a Class B endorsement capped at 25 tons of cooling, and nearly every commercial or industrial chiller is larger than that cap. Refrigerant handling also requires federal Section 608 technician certification.

The mechanical code depends on the city. Dallas adopted the 2021 International Mechanical Code with amendments effective May 12, 2023, while Houston adopted the 2021 Uniform Mechanical Code with amendments effective in January 2024, and both draw on ASHRAE 15 for machinery room safety. A like-for-like repair rarely triggers a permit, but a replacement or a refrigerant change usually does, along with machinery room ventilation, refrigerant detection and relief piping that meet the adopted code. Paul Industries checks those requirements before a replacement is priced, so the quote includes the room work as well as the machine.

Restarting chillers after a Gulf Coast hurricane outage

Restarting chillers after a Gulf Coast hurricane outage takes a checklist, because machines that sat without power for days in summer heat and humidity, sometimes with debris or water in the yard, can be damaged on a careless restart. Hurricane Beryl showed the scale in July 2024, when outages reached 2.26 million CenterPoint customers and some Houston buildings went without utility power for most of a week.

Before a restart, Paul Industries inspects for water intrusion in starters, drives and control panels, checks motor insulation resistance, confirms oil level and oil heater operation, verifies refrigerant pressures, clears air-cooled coils and tower fill of debris, and confirms flow through the evaporator and condenser before the compressor runs. Machines with variable speed drives get a drive inspection, since moisture and surge damage there are common. Cooling towers are checked as well: basins are cleaned of storm debris, fill and drift eliminators inspected, fan blades and gearboxes checked for water intrusion, and the water treatment program restarted before condenser water flows back to the chillers, since a tower full of debris and untreated water fouls tubes within weeks. The plant is then brought back one chiller at a time, with temperatures and pressures logged against pre-storm readings.

Chiller repair across Texas regions

Chiller repair across Texas regions follows each market’s mix of buildings, industry and weather, so each market brings its own common jobs.

Chiller repair: Houston, Pasadena and Baytown

Chiller repair Houston facilities call for spans the Texas Medical Center’s hospitals, downtown and Galleria office towers, the Energy Corridor, and the refineries and chemical plants of Pasadena, Baytown and the Ship Channel. Corrosion, condenser fouling and storm restarts lead the list, and HVAC chiller repair at hospitals is planned around infection control and backup capacity for surgical and critical areas.

Chiller repair: Dallas-Fort Worth

Chiller repair Dallas-Fort Worth owners need most often covers high-rise offices, hospitals, campuses, distribution and manufacturing plants, and the region’s large data center cluster. Commercial chiller repair in North Texas towers is scheduled for weekends and shoulder months, and freeze damage from hard winters is a recurring winter job.

Chiller repair: San Antonio and Austin

Chiller repair San Antonio and Austin buildings require reflects long seasons, hard water and fast-growing campuses. A San Antonio chiller plant serving a hospital or university runs nearly year-round, and scale from mineral-heavy makeup water makes tube cleaning and tower water treatment frequent tasks. Austin’s semiconductor plants, research buildings and data centers add process and precision cooling loads.

West Texas, El Paso and the Rio Grande Valley

In El Paso, Midland, Odessa, Lubbock and Amarillo, dust and dry heat load air-cooled condenser coils, while the plains bring hard freezes. In the Rio Grande Valley, from McAllen to Brownsville, chillers run almost year-round in humid heat, so overhauls are fitted into the short cool season.

Industrial chiller maintenance for Texas plants

Industrial chiller maintenance for Texas plants combines the manufacturer’s schedule with the EPA’s leak rate records and a calendar built around Texas weather, so the machine is ready for the summer peaks and protected for the winter freeze. ASHRAE/ACCA 180 offers a standard practice many owners adopt for their written program.

A Texas maintenance calendar for chillers in plants and large buildings
WhenTaskTexas reason
Every refrigerant additionLeak rate calculation and recordRequired for HFC systems of 15 pounds or more from January 1, 2026
February to AprilTube cleaning, tower startup, controls and safeties check, coil cleaningReady before the June to September peak months
Before hurricane seasonStarter and drive inspection, generator transfer test, restart procedure reviewGulf Coast storms bring multi-day outages
AnnuallyOil and refrigerant analysis, vibration readings, motor insulation testsLong run hours bring compressor wear forward
Every few yearsEddy current testing; compressor inspection or overhaul by operating hoursHard makeup water and long seasons shorten intervals
Before the first freezeDrain or glycol-protect idle machines; verify heat trace and heater circuitsFebruary 2021 split evaporators across the state

Texas owners can run that calendar through Paul Industries service contracts, where reclaimed refrigerant is sampled and compared with AHRI 700 purity limits, and tower water work that ties back to cooling tower water treatment.

Repair or replace at Texas power prices

The repair or replace decision at Texas power prices weighs a lower electricity rate against longer run hours: Texas industrial power averaged 6.12 cents per kilowatt-hour in 2024 against 8.13 nationally (EIA), which stretches efficiency paybacks, but Texas chillers run more hours than machines in cooler states. As an illustration, a 600-ton chiller that improves by 0.20 kilowatts per ton after replacement and runs the equivalent of 3,500 full-load hours a year saves about 420,000 kilowatt-hours, roughly $25,700 at the 2024 Texas industrial average, before any demand or transmission savings.

Refrigerant, condition and leak history usually decide the case before energy does. A machine with an R-22 charge, a rising leak rate and worn tubes points to replacement; a sound R-134a machine with a compressor bearing fault earns its repair. Paul Industries runs the energy figure on the owner’s own tonnage, run hours and tariff, including peak-interval effects in ERCOT, and prices both paths.

What drives chiller repair cost in Texas?

Chiller repair cost in Texas follows six things: what failed and what parts that takes, how big the machine is and what kind, how much refrigerant comes out and goes back in, how hard the machine is to reach and rig, the safety programs of a refinery or hospital, temporary cooling during the outage, and the season, since summer work in a building with little spare capacity needs more temporary equipment. Freeze damage repairs that involve water in the refrigerant circuit cost more than a tube repair alone, because of dehydration, oil and refrigerant replacement.

Chiller replacement cost adds the new machine, rigging, piping and electrical changes, machinery room code upgrades and refrigerant recovery from the old unit. Each repair quote follows the diagnosis and lists refrigerant, parts and labor as separate lines, and any major repair arrives with a replacement budget beside it for comparison.

Who repairs chillers in Texas?

Paul Industries repairs chillers in Texas, working on centrifugal, screw, scroll and air-cooled machines of the major makes at refineries, chemical and food plants, hospitals, universities, office towers and data centers across the state. With headquarters at 256 Shore Drive in Kilmarnock, Virginia, Paul Industries is an East Coast contractor that takes chiller repair, overhaul, retrofit and replacement work statewide and in all 50 states. Brand-specific work is described on Trane chiller repair, Carrier chiller repair and York chiller repair.

The chiller and everything around it fall under a single contract, so a fault that starts in the tower or the piping is fixed where it starts. Data center plants follow the redundancy practice on data center cooling in Texas, campus heating plants appear on boiler repair in Texas, and identical chiller work is delivered in Paul Industries’ headquarters state on chiller repair in Virginia and in another long-season market on chiller repair in Florida.

Chiller repair and replacement across Texas from Paul Industries

Paul Industries repairs, overhauls, maintains, supplies and installs chillers for Texas plants, hospitals, campuses, commercial buildings and data centers. A repair quote starts from the nameplate data, refrigerant type and charge, alarm history and a few weeks of logs; a replacement study also needs the load profile and the site’s electric tariff. Call 201-450-8280 or request a quote. The rest of Paul Industries’ Texas work is gathered on the Texas overview.

Standards referenced: EPA AIM Act HFC phasedown (40 CFR Part 84) · EPA Emissions Reduction and Reclamation rule, 40 CFR 84.106 · EPA Technology Transitions rule · Clean Air Act Section 608 (40 CFR 82 Subpart F) · Texas Occupations Code Chapter 1302 (air conditioning and refrigeration contracting) · International Mechanical Code and Uniform Mechanical Code as adopted by Texas cities · ASHRAE 15 · AHRI 700 · ASME Boiler and Pressure Vessel Code Section VIII

Frequently asked questions

Who handles chiller repair at Texas Medical Center hospitals and Houston office towers?

Paul Industries handles chiller repair for Houston hospitals, Texas Medical Center buildings, downtown and Galleria towers and Energy Corridor campuses. Houston’s humidity keeps machines running into the night, so condenser fouling and corrosion lead the repair list, and hospital work is planned around backup capacity and infection control before a machine is isolated.

Who works on chillers at refineries and chemical plants in Pasadena, Baytown and Beaumont?

Paul Industries works on chillers at refineries, chemical plants and terminals in Pasadena, Baytown, Deer Park, Beaumont, Port Arthur and Corpus Christi. Repairs follow the plant’s permits to work and are timed to outages or turnarounds, with coils, enclosures and materials chosen for atmospheres carrying hydrogen sulfide, chlorides or acid vapors.

Does Paul Industries repair chillers in Dallas, Fort Worth and the North Texas suburbs?

Yes. Paul Industries repairs chillers in Dallas, Fort Worth, Irving, Plano, Richardson, Arlington and across North Texas, at offices, hospitals, plants and data centers. Hot July nights keep lift high, and hard winters bring freeze damage, so condenser performance in summer and layup or glycol protection in winter are both part of the work.

Who provides chiller repair in San Antonio, Austin and the Rio Grande Valley?

Paul Industries provides chiller repair in San Antonio, Austin, Round Rock, San Marcos, McAllen, Harlingen and Brownsville. Central Texas makeup water is often hard, so scale in condenser tubes is a common cause of high head pressure, and Valley machines run nearly year-round, leaving a short cool season for overhauls.

Can a chiller evaporator that froze in a Texas winter storm be repaired?

Often, yes. The machine is drained and pressure tested on both sides to find every split tube, refrigerant and oil are checked for moisture, damaged tubes are plugged or replaced after eddy current testing of the bundle, and the circuit is dehydrated if water got in. Widespread damage or a contaminated compressor can tip the decision toward replacement.

How should a Texas chiller be protected before a hard freeze?

Idle machines are drained or protected with glycol, outdoor piping is heat traced and insulated, and heat trace, crankcase heaters and controls are placed on circuits that stay powered during a grid emergency. Running plants keep water moving through exposed sections. Paul Industries reviews those protections each autumn under its service contracts.

How long do industrial chillers last in Texas service?

Industrial chiller life depends on duty, maintenance and environment more than on age alone, and Texas conditions shorten it for some machines: long run hours bring compressor overhauls forward, corrosive Gulf Coast and refinery air attacks coils and cabinets, and freeze damage can end a machine early. Tube condition, refrigerant and leak history usually decide when replacement makes sense.

What is the typical chiller replacement cost driver in a Texas building?

Tonnage and machine type set the equipment cost, and the rest comes from rigging access, piping and electrical changes, machinery room upgrades required by the adopted mechanical code, refrigerant recovery from the old machine and temporary cooling during the changeover. Paul Industries prepares a budget figure once tonnage and site conditions are known, then a fixed price after a site survey.

Which TDLR license class covers chiller repair in Texas?

TDLR’s air conditioning and refrigeration rules give the Class B endorsement a ceiling of 25 tons of cooling and 1.5 million Btu per hour of heating, while Class A carries no size ceiling. Commercial and industrial chillers sit well above 25 tons, which puts their repair under the Class A endorsement. Anyone recovering or charging refrigerant on the machine also needs federal Section 608 technician certification.

Does replacing a chiller in Houston or Dallas need a permit?

A replacement usually needs a mechanical permit under the city’s adopted code: the 2021 Uniform Mechanical Code with amendments in Houston, and the 2021 International Mechanical Code with amendments in Dallas. The permit review covers the machinery room, ventilation, refrigerant detection and relief piping, so Paul Industries includes those items when pricing a replacement.

What does the 2026 EPA leak rule mean for a Texas plant's process chillers?

From January 1, 2026, appliances holding 15 pounds or more of HFC refrigerant need a leak rate calculation each time refrigerant is added. Industrial process refrigeration exceeding a 30 percent annual leak rate must be repaired within 30 days, or 120 days if a process shutdown is required, followed by verification tests. Paul Industries files the calculations and test records with each repair.

Why do air-cooled chillers corrode so fast near the Texas coast and refineries?

Salt-laden air near the Gulf and industrial atmospheres containing sulfur compounds and chlorides attack aluminum fins, copper tubes and their joints, and humid air keeps surfaces wet. Corroded fins lose capacity, and corrosion at brazed joints causes refrigerant leaks. Coated coils, sealed enclosures, regular rinsing and joint inspections slow the damage, and Paul Industries recommends recoating or coil replacement before leaks start.

What season is right for a Texas chiller overhaul?

Late autumn through early spring suits most Texas buildings, since loads are lowest and the June to September peak months, which set transmission charges inside ERCOT, are avoided. Plants schedule around turnarounds, hospitals and data centers overhaul one machine at a time with redundancy confirmed, and Valley sites use their short cool season.

Can a Texas hospital chiller be repaired without losing cooling to critical areas?

Usually, yes. The remaining capacity is checked against the expected load for the outage window, air handlers serving operating rooms and sterile areas are confirmed able to hold their setpoints, and temporary cooling is connected where margin is thin. Work follows the hospital’s outage and infection control procedures, and the repaired machine is tested under load before it rejoins the plant.

Is an R-22 chiller in Texas still worth repairing?

It can be, for a short horizon. EPA ended R-22 production and import in 2020, but existing machines may still be serviced with reclaimed refrigerant. A small, identifiable leak on an otherwise sound machine is worth fixing while a replacement is planned; a large leak, worn tubes or a failing compressor usually is not. Paul Industries prices both paths so the owner can decide.

How are chillers restarted after a long power outage in the Houston area?

Before restart, starters, drives and panels are checked for water, motor insulation is tested, oil level and heaters are confirmed, refrigerant pressures are verified, coils and tower fill are cleared of debris and flow is proven through both heat exchangers. Machines are then brought back one at a time, with readings compared against pre-outage logs.

Which logs and nameplate details speed up a Texas chiller diagnosis?

Nameplate photos with tonnage and serial number, the refrigerant and its charge, a printout of active and recent alarms, a few weeks of trend data on suction and discharge pressures, approach temperatures and amps, and the refrigerant addition log. For coastal or freeze-damaged machines, coil and tube sheet photos help too. Paul Industries plans the first visit around those details.

Have a chiller to repair or replace in Texas?

Share the nameplate photo, refrigerant type, recent alarms and a few weeks of operating trends. Call 201-450-8280 or request a quote.