Paul Industries provides boiler repair in Alabama for manufacturing plants, poultry processors, paper and chemical sites, hospitals and campuses, repairing firetube, watertube, electric and cast iron sectional boilers to the National Board Inspection Code that the state adopts. Alabama came late to boiler regulation, and its Boiler and Pressure Vessel Safety Act carves out more equipment than most states do, so the first question on any Alabama repair is which rules reach that particular unit. Paul Industries answers that question, repairs the boiler, prepares it for the inspector and returns it to service with the records the state and the insurer expect.
Request a quote or call 201-450-8280
What does boiler repair in Alabama involve under the state Act?
Boiler repair in Alabama involves diagnosing the failure, repairing tubes, shells, sections, refractory, burners and safety controls, and documenting the work so that the inspector responsible for the boiler accepts it, under rules adopted by the state’s Board of Boilers and Pressure Vessels. The Alabama Boiler and Pressure Vessel Safety Act, passed as Act 2000-315 and codified at Sections 25-12-1 through 25-12-22 of the Code of Alabama, applies to boilers and pressure vessels in general and then lists the exceptions. The Board’s rules, published as Chapters 480-7-1 through 480-7-7 of the Alabama Administrative Code, adopt the ASME Boiler and Pressure Vessel Code for construction, the National Board Inspection Code and API 510 for repairs and alterations, ASME B31.1 for boiler piping, ASME CSD-1 for controls on boilers under 12.5 million Btu per hour and NFPA 85 above that size.
The national picture of tube failures, burner faults, retubing and repair methods is on the boiler repair service page. This page covers what is particular to Alabama: the agency, the inspection calendar, the exemptions, the incident rules, the preparation an inspector expects, and the plants and buildings where Alabama boilers carry their heaviest duty.
Which agency runs the Alabama boiler law today?
The Alabama boiler law is administered today by the Inspections Division of the Alabama Department of Workforce in Montgomery, which runs the state’s elevator, mining and boiler safety programs, although the statute itself still names the Department of Labor. The current install permit form, revised in January 2026, carries the Department of Workforce heading, and the division is led by a director who also serves as chief inspector, so an Alabama boiler inspector employed by the state reports to that office.
Alabama was the 49th state to pass a boiler and pressure vessel safety act, and inspections began in earnest on February 5, 2004. A nine-member Board of Boilers and Pressure Vessels advises on the rules, with seats for owners and users of power boilers, heating boilers and pressure vessels, manufacturers, the crafts, heating contractors, insurers and the public. Inspections are made by the chief inspector and deputy inspectors employed by the state, by special inspectors employed by insurance companies, and, for pressure vessels, by owner-user inspectors at companies that run an established inspection service. Equipment covered by an insurance policy is normally inspected by the insurer’s special inspector, who files the report with the chief inspector within 30 days; equipment without coverage is inspected by a state deputy.
Alabama boiler inspection intervals by boiler type
Alabama boiler inspection intervals depend on the boiler class defined in the Act: power boilers and high temperature water boilers are inspected every year, and low pressure steam, hot water heating and hot water supply boilers every two years. The Act defines a heating boiler as a steam or vapor boiler at 15 psig or less, or a hot water boiler at 160 psig or less and 250 degrees Fahrenheit or less, and a power boiler as one generating steam above 15 psig. Owners who want to know how often are boiler inspections required for a given unit start with its nameplate pressure and service.
| Boiler class | Certificate inspection | Internal inspection | Certificate valid for | State inspection fee (deputy) |
|---|---|---|---|---|
| Power boiler, steam above 15 psig | Every year | Each year where construction permits; external under pressure where possible | Up to 14 months | $60, $90 or $120 by heating surface |
| High pressure, high temperature water boiler | Every year | Each year where construction permits | Up to 14 months | $60, $90 or $120 by heating surface |
| Low pressure steam or vapor heating boiler | Every two years | Every four years where construction permits | Up to 26 months | $90 with manhole, $60 without |
| Hot water heating and hot water supply boilers | Every two years | At the inspector’s discretion | Up to 26 months | $90 with manhole, $60 without |
| Water heater of 200,000 Btu per hour or more | Classed as an HLW boiler and permitted at installation | At the inspector’s discretion | Per its class | Per its class |
The certificate is posted under glass, or similarly protected, in the room that houses the unit. A grace period of two months is allowed beyond the annual and biennial intervals for power and low pressure steam boilers, and a unit overdue by more than six months is inspected by a state deputy, with the owner invoiced. Where a special inspector or owner-user inspector misses the due date by more than 60 calendar days, the Act sets a fine of $500 for each object. Boiler inspection requirements by state vary widely, and Alabama’s schedule sits in the middle of the national range; what sets it apart is the size of its exemption list.
Which boilers does the Alabama boiler law leave out?
The Alabama boiler law leaves out boilers and pressure vessels operated as part of a manufacturing process, boilers used to generate electricity, equipment run by public utilities, equipment subject to OSHA standards and several small or special categories, provided the conditions attached to each exception are met. The manufacturing process exception requires the operator to carry insurance or self-insurance. The electricity generation exception adds a requirement that the boiler be inspected regularly, to the ASME Code’s minimum safety requirements, by an inspector holding a state certificate of competency.
Smaller exclusions cover hot water supply boilers with ASME and National Board relief valves that stay at or below 200,000 Btu per hour, 210 degrees Fahrenheit and 120 gallons, equipment under federal control, and autoclaves used to sterilize instruments in a professional office. Boilers on farms used for agriculture and heating boilers in private homes or apartment buildings of fewer than six units are spared the certificate inspections but remain within the Act.
| Situation | Position under the Act | What still governs the repair |
|---|---|---|
| Hospital, school or office heating boiler | Within the Act; certificate inspection every two years | NBIC repair rules, inspector acceptance, state records |
| Process steam boiler at a manufacturing plant | Excepted when operated as part of the manufacturing process with insurance or self-insurance | The insurer’s inspection requirements, NBIC practice, the plant’s own mechanical integrity program |
| Boiler generating electricity, including plant cogeneration | Excepted, with insurance and regular inspection by a certificate-of-competency holder | ASME Code safety minimums and the inspector’s findings |
| Poultry plant boiler for scalders, washdown and sanitation | Depends on whether it is operated as part of the process; confirmed case by case | NBIC repair rules and the insurer either way |
| Small hot water supply boiler at or under 200,000 Btu per hour, 210 F and 120 gallons | Excepted | Manufacturer instructions and the mechanical code adopted for the building |
| Owner who wants a state certificate on an excepted unit | The Act lets owners and users request to waive the exemption | Full Alabama boiler inspection schedule |
An exemption from state certificates is an administrative fact, and the physics stays the same. An excepted process unit still needs a repair method an insurer will accept, the same safety valve capacity, the same water level protection and the same weld quality. Paul Industries applies NBIC repair practice to every Alabama unit, with or without a state certificate, which keeps the records ready if the exemption status ever changes after a sale, a change of use or a new insurer.
How is a repair authorized and accepted in Alabama?
An Alabama boiler repair is authorized and accepted under Rule 480-7-5-.06, which requires repairs and alterations to follow the latest edition of the National Board Inspection Code or API 510, as applicable, and to be acceptable to the inspector responsible for in-service inspection of that unit. Repairs and alterations made under the NBIC are carried out under a valid National Board R certificate whose scope covers the type of work, and they are documented and submitted to the chief inspector as the NBIC requires, normally on a Form R-1 report for a repair.
The practical sequence on a welded repair is short and strict. The inspector sees the damage and agrees the repair method before work starts, the welding follows a qualified procedure with qualified welders, the inspector sees the finished work and the pressure test where one is required, and the R-1 report closes the loop with the chief inspector. Fittings and appliances are held to the standards for new installations when they are repaired or replaced, which means ASME Section I practice on power units and Section IV on heating units. A cracked tube sheet ligament, a bulged furnace, a wasted stay or a corroded drum is therefore a planned repair with an inspector’s hold points, not a quick weld between production runs.
Paul Industries carries out industrial steam boiler repair and commercial steam boiler repair on this basis, from tube replacements and plug-and-patch work to retubing, refractory, burner overhauls and control upgrades, and it brings the inspector in at the start rather than after the unit has been closed up. On rerates, which the Act allows under a later ASME edition and the NBIC subject to the concurrence of the inspector at the point of installation, the calculations go to the inspector before the new nameplate data are applied.
Getting a boiler ready for an Alabama certificate inspection
An Alabama certificate inspection requires the owner or user to prepare the unit and, when the inspector calls for it, to prepare and apply a hydrostatic or other pressure test on the agreed date. Rule 480-7-5-.07 spells out the preparation in detail, and an inspector who finds the unit unprepared may decline the inspection and withhold or suspend the certificate. The state also charges for an inspector’s time when the equipment, access or personnel are not ready, at $100 an hour.
- Lock out or tag out the fuel supply and ignition system under the plant’s procedures.
- Drain the water and wash the waterside thoroughly.
- Remove manhole and handhole plates, washout plugs and water column inspection plugs as the inspector requires, and cool and clean the furnace and combustion chambers.
- Remove grates from internally fired units, and insulation or brickwork where the inspector needs to see headers, furnace, supports or seams.
- Remove the pressure gauge for testing when asked.
- Where boilers share a common header, close, tag and padlock the non-return and steam stop valves with the drain between them open, and close, tag and padlock the feed valves.
- Meet OSHA’s permit-required confined space standard, 29 CFR 1910.146, before anyone enters a drum, header or furnace, with atmospheric testing and an attendant outside.
Alabama limits a hydrostatic test to 1.5 times the maximum allowable working pressure, controlled so the test pressure is never exceeded by more than 6 percent. Safety valves are removed or held closed with a testing clamp, never by screwing down the spring, the test water is at least 70 degrees Fahrenheit, and the metal is no hotter than 120 degrees during the inspection. Paul Industries does this preparation as part of the repair outage, so the inspector’s visit, the internal inspection and the repair inspection happen in a single shutdown where the schedule allows.
What happens after a boiler incident in Alabama?
An Alabama boiler incident that injures someone must be reported to the chief inspector within 24 hours with a detailed written report, or on the first business day after a weekend. When the injury needs immediate transport to a medical facility, notice goes by telephone or email within four hours, and neither the equipment nor any part of it may be removed or disturbed until the Chief Inspector gives permission, except to save life or limit consequential damage. An inspection follows every reportable incident.
The four-hour rule has a direct effect on repair planning. A tube rupture that scalds an operator freezes the room as evidence, so Paul Industries plans temporary steam, isolation and cleanup around the Chief Inspector’s release rather than around the plant’s production schedule. Once the release is given, the root cause work comes first: water chemistry records, low-water cutoff test history, firing records and the failed part itself, which often points to a feedwater, deaerator or treatment problem that a tube replacement alone will repeat. Plants that need that side of the work as well can see the boiler water treatment page.
Safety valves, low-water cutoffs and CO monitors in Alabama boiler rooms
Safety valves, low-water fuel cutoffs and carbon monoxide monitors are the three boiler room items Alabama’s rules address most directly, and each one is a common repair finding. Weighted-lever safety valves and valves with a cast iron seat or disk are prohibited on power boilers and must be replaced by direct spring-loaded pop valves meeting ASME Section I. Every boiler carries at least one ASME and National Board marked safety valve, and a boiler with more than 500 square feet of water heating surface, or an electric input above 1,100 kilowatts, carries two or more, connected directly to the boiler without unnecessary intervening pipe.
Automatically fired steam units each need an automatic low-water fuel cutoff that shuts off the fuel when the water falls to the lowest safe waterline, which should be no lower than the lowest visible part of the gauge glass. Blowdown that enters a sanitary sewer passes through blowoff equipment that cools it to 140 degrees Fahrenheit or less and drops it to 5 psig or less. Since February 13, 2022, new boiler and equipment rooms with fired boilers or water heaters must have carbon monoxide monitors, hard wired with battery backup, mounted at least five feet above the floor, alarming at 200 parts per million and audible outside the room; the same arrangement is strongly recommended for existing rooms, and inspectors check the monitors on routine visits.
Paul Industries replaces and resets safety valves, rebuilds and tests low-water cutoffs, upgrades burner management to CSD-1 or NFPA 85 as the firing rate requires, and installs CO monitoring that meets the Alabama parameters. Steam systems downstream of the boiler often contribute to the problems found at inspection, and the steam trap page covers the condensate side.
Older and riveted boilers under Alabama rules
Older and riveted boilers are covered by Rule 480-7-5-.08, which sets age limits for boilers of nonstandard construction installed before the Act took effect. The general limit is 30 years, but a unit without lap-riveted longitudinal joints may continue in service after a thorough internal and external inspection and, where the inspector requires it, a pressure test at 1.5 times the allowable working pressure held for at least 30 minutes without distress or leakage. A nonstandard unit with lap-riveted longitudinal joints operating above 50 psig is limited to 20 years and, once removed from its setting, may not be reinstalled above 15 psig.
A lap seam crack along a longitudinal riveted joint takes the shell or drum out of use immediately, and patching it is prohibited. Alabama still has old mill, institutional and heating boilers in service, and the decision on those units is usually between an inspector-approved repair now and a planned replacement before the next certificate inspection forces the issue. Paul Industries assesses the unit, prices both routes and schedules the one the owner chooses.
Where Alabama boilers carry the heaviest duty
Alabama boilers carry their heaviest duty at paper mills, poultry processors, chemical plants, vehicle and parts plants, food and beverage plants, hospitals and universities, spread across a state served by Alabama Power in its southern two-thirds and by TVA power distributors such as Huntsville Utilities in the north. The Alabama Poultry and Egg Association counts 18 poultry processing plants and 17 further processing plants in the state, and the forestry sector counts more than 110 manufacturing facilities, including paper mills, according to the Alabama Department of Commerce.
Boiler repair in Birmingham, Tuscaloosa and Anniston
Boiler repair in Birmingham centers on hospitals, university and medical campuses, manufacturing plants and food and beverage production, including Coca-Cola UNITED’s new facility in the city’s Kingston community. Tuscaloosa and the Vance area add vehicle manufacturing, where Mercedes-Benz announced a further $4 billion investment in 2026, and Anniston and Calhoun County add further industrial boiler rooms. Heating boilers in this region fall squarely within the state certificate schedule, so their repairs are planned around the next inspection date.
Boiler repair, Huntsville, AL and Decatur
Boiler repair, Huntsville, AL and Decatur work serves aerospace and defense campuses, vehicle and engine plants, industrial plants along the Tennessee River and a coming pharmaceutical site: Lilly’s $6 billion synthetic medicine active ingredient plant in Huntsville, with construction set to begin in 2026 and completion slated for 2032. Pharmaceutical steam plants add clean steam generators and tighter documentation to the usual repair scope.
Boiler repair, Mobile, AL and the Gulf Coast
Boiler repair, Mobile, AL and the Gulf Coast covers process plants, the AM/NS Calvert steel mill in Mobile County, shipbuilding, aircraft assembly and port facilities. Salt air, humidity and hurricane season all bear on outdoor stacks, economizers and burner enclosures, and storm preparation includes securing fuel supplies and planning restarts after outages.
Montgomery, Auburn and Opelika, Dothan and the Shoals
Montgomery and the Auburn and Opelika area combine vehicle assembly, including Hyundai’s Montgomery plant, and manufacturing plants with state buildings and universities, where the state building code also applies. Dothan and the Wiregrass add food and manufacturing plants, and the Shoals add manufacturing along the Tennessee River.
| Region | Main boiler users | Typical duty | Repair focus |
|---|---|---|---|
| Birmingham, Tuscaloosa and Anniston | Hospitals, campuses, manufacturing, beverage and vehicle plants | Heating and process steam, year-round hot water | Section repairs, retubing, burner and control upgrades timed to certificate dates |
| Huntsville and Decatur | Aerospace, engine and vehicle plants, industrial plants, a pharmaceutical build | Process steam, clean steam feed, space heating | Documented repairs, CSD-1 controls, water treatment fixes |
| Mobile and the Gulf Coast | Process plants, steel, shipbuilding, aircraft assembly | High pressure process steam, continuous operation | Tube failures, refractory, outdoor corrosion, outage repairs |
| Montgomery, Auburn and Opelika | Vehicle and parts plants, state buildings, universities | Paint shop and process heat, campus heating | Controls, low-water protection, CO monitoring in boiler rooms |
| Dothan, the Wiregrass and the Shoals | Food plants and manufacturing | Scalder and sanitation steam, hot water washdown | Scale and corrosion damage, feedwater systems, quick-turn sanitation outages |
Boiler repair and replacement: the Alabama installation permit
Boiler repair and replacement decisions in Alabama turn on the installation permit, because a replacement unit needs one before any installation work starts. The person or company responsible for the installation submits a Request to Install with a $50 fee for each object and the Manufacturer’s Data Report; boilers of special design need drawings and calculations, and a permit for an Alabama State Special carries a $75 fee. All boilers must be ASME Code constructed and stamped, and all except cast iron and cast aluminum sectional boilers must be registered with the National Board by the manufacturer. A permit with no installation activity expires after 12 months.
After installation, the unit receives an Alabama serial number, stamped with the letters AL above the number and a five-point star at each end in 5/16 inch low-stress dies, or carried on a corrosion-resistant tag where stamping would cause damage; the number may never be concealed by lagging or paint. The rules recommend 3 feet of clearance above and around a boiler and 5 feet in front of a manhole, require two remote exits from a boiler room larger than 500 square feet with a boiler of 1 million Btu or more, and call for runways with two exits where boilers are serviced from above.
Building permits for the mechanical work come from the city or county where the plant sits, except on state-owned or state-funded property, schools, public colleges, hotels and motels and movie theaters, where the Division of Construction Management enforces the state building code based on the 2021 International Mechanical Code with 2025 amendments. Alabama also requires a general contractor license for any undertaking of $100,000 or more, labor and materials included, which covers most replacements. Paul Industries supplies and installs replacement boilers, handles the permit request and data reports, and coordinates the first certificate inspection.
What does boiler repair in Alabama cost?
The cost of boiler repair in Alabama is set by the type and extent of damage, access to the failed parts, whether a code welded repair and inspector hold points are needed, the outage window and any temporary steam, while the state’s own charges are small and fixed by rule. A state deputy’s inspection costs $60 to $120 for a power boiler depending on heating surface and $60 or $90 for a heating boiler, and the certificate fee is $50, charged annually for power boilers and every two years for heating boilers.
Repair costs rise sharply with access. A few leaking tubes on a firetube boiler are a short repair; a set of failed tubes deep in a watertube bank, a furnace bulge, or refractory work in a pulp mill boiler means scaffolding, confined space controls and an inspector’s hold points. Energy is the other side of the comparison: EIA’s 2024 figures put Alabama industrial power at 7.25 cents a kilowatt-hour, below the 8.13 cent US figure, so for an electric unit the savings from a replacement weigh less than they would at the national price. Paul Industries prices the repair after inspection, shows parts, labor, testing and temporary steam separately, and gives a budget figure for replacement alongside any major repair.
Who repairs boilers in Alabama?
Paul Industries repairs boilers in Alabama for manufacturers, processors, hospitals, universities and building owners, working to the NBIC and the state’s rules on firetube, watertube, electric and cast iron sectional units. Paul Industries is an East Coast contractor headquartered at 256 Shore Drive, Kilmarnock, Virginia, formerly based in northern New Jersey and then Pennsylvania, and it takes work across Alabama, in all 50 states and abroad.
The same approach runs on the firm’s other state pages, including boiler repair in Virginia, its headquarters state, and the neighboring Georgia and Tennessee pages, while the Southeast page compares boiler, building and tank rules across the region. Boiler work in Alabama often connects to other plant systems that Paul Industries builds: pressure vessels for Alabama plants, process and steam piping, code welding at Alabama plants and chiller repair in the same central plant. Poultry processors can see the meat and poultry page for the wider plant scope.
Boiler repair from Paul Industries for Alabama plants and buildings
Paul Industries diagnoses, repairs, retubes, rerates, tests, maintains, supplies and installs boilers across Alabama, with the inspector involved from the first look at the damage to the final R-1 report. For a repair, send the boiler make, model, National Board and Alabama serial numbers, the nameplate pressure and rating, the fuel, the latest inspection report and a description or photographs of the damage; for a replacement study, add the steam or hot water load profile and the outage window. Call 201-450-8280 or request a quote, and see the Alabama page for the other process, water and piping work Paul Industries delivers in the state.
Standards referenced: Alabama Boiler and Pressure Vessel Safety Act (Code of Ala. 1975, Sections 25-12-1 to 25-12-22) · Ala. Admin. Code Chapters 480-7-1 through 480-7-7 · ASME Boiler and Pressure Vessel Code, Sections I and IV · National Board Inspection Code (NBIC) · API 510 · ASME B31.1 · ASME CSD-1 · NFPA 85 · OSHA 29 CFR 1910.146 · 2021 International Mechanical Code (Alabama state building code)
Frequently asked questions
Who handles boiler repair, Birmingham, AL hospitals and plants rely on?
Paul Industries handles boiler repair, Birmingham, AL hospitals, medical campuses, universities and manufacturing plants rely on, including Jefferson and Shelby County sites. Heating boilers there fall under the state certificate schedule, so repairs are planned with the inspector before the certificate date. Send the boiler data, the latest inspection report and photographs of the damage, and Paul Industries scopes the repair and the inspection visit together.
Does Paul Industries repair boilers at Mobile and Baldwin County plants?
Paul Industries repairs boilers at process plants, steel and shipbuilding sites, aircraft assembly and institutions in Mobile and Baldwin counties. Many Gulf Coast process boilers run continuously, so tube and refractory repairs are planned into outages with temporary steam where production cannot stop, and outdoor stacks, economizers and burner housings are checked for salt air corrosion while the boiler is down.
Who repairs boilers for plants in Huntsville, Decatur and the Shoals?
Paul Industries repairs process and heating boilers for aerospace, vehicle, engine, industrial and food plants in Huntsville, Decatur, Athens and the Shoals. North Alabama plants buy TVA power through distributors such as Huntsville Utilities, and many run gas-fired steam for process heat. Repairs follow the NBIC and the inspector’s acceptance, with control upgrades to CSD-1 where the burner management is out of date.
What does the Alabama state boiler inspector check on a routine visit?
The Alabama state boiler inspector checks the boiler’s condition, safety valves, low-water fuel cutoff, gauges and controls, the posted certificate, the Alabama serial number and, in rooms built since 2022, the carbon monoxide monitor. An internal inspection needs the boiler drained, washed, opened and locked out. Boilers under an insurance policy are normally inspected by the insurer’s special inspector, who files the report with the chief inspector within 30 days.
How often are boiler inspections required for a hospital boiler in Alabama?
A hospital heating boiler, steam at 15 psig or less or hot water at 160 psig and 250 F or less, receives a certificate inspection every two years. A low pressure steam boiler also gets an internal inspection every four years where construction permits. A hospital power boiler generating steam above 15 psig is inspected every year, internally where construction permits, so repairs are best timed to those visits.
Is a process boiler at an Alabama manufacturing plant exempt from state inspection?
A boiler operated and maintained as part of a manufacturing process is excepted from the Act when the operator carries insurance or self-insurance, so it receives no state certificate. The insurer’s inspections still apply, and the repair is still made to NBIC practice. Owners may also ask to waive the exemption and bring the boiler under the state schedule, which some do for consistent records across sites.
Can a leaking boiler be repaired in place at an Alabama plant?
A leaking boiler can usually be repaired in place: leaking tubes are replaced or, where the code allows, plugged, seal welds and handhole gaskets are renewed, and cracked sections on cast iron boilers are replaced. Pressure part welding follows the NBIC with the inspector’s acceptance. The cause, such as scale, oxygen pitting, thermal shock or a low-water event, is identified before the boiler goes back into service.
What is the state boiler inspection cost in Alabama?
The state boiler inspection cost in Alabama, when a deputy inspects, is $60 for a power boiler of 50 square feet of heating surface or less, $90 up to 2,000 square feet and $120 above that, counting one kilowatt as one square foot for electric boilers. Heating boilers cost $90 with a manhole and $60 without. The certificate fee is $50, and an unprepared inspection is billed at $100 an hour.
Where are the Alabama boiler rules published?
The Alabama boiler rules are published as Chapters 480-7-1 through 480-7-7 of the Alabama Administrative Code, adopted by the Board of Boilers and Pressure Vessels under Sections 25-12-4, 25-12-6 and 25-12-14 of the Code of Alabama. They adopt the ASME Boiler and Pressure Vessel Code, the NBIC, API 510 and 570, ASME B31.1, CSD-1, NFPA 85 and PVHO-1, in the latest editions unless the Board states otherwise.
What is the Alabama boiler code for new construction?
What people call the Alabama boiler code is, for new construction, the ASME Boiler and Pressure Vessel Code adopted by reference in Rule 480-7-1-.02, with Section I for power boilers and Section IV for heating boilers. Every boiler installed in the state must be ASME Code constructed and stamped and, except cast iron and cast aluminum sectional boilers, registered with the National Board by its manufacturer.
Does an electric boiler fall under the Alabama boiler law?
An electric boiler falls under the Alabama boiler law, because the Act’s definition of a boiler covers vessels heated by electrical energy as well as by fuel. For fee purposes, one kilowatt of input counts as one square foot of heating surface. An electric boiler above 1,100 kilowatts needs two or more safety valves, and its repairs follow the same NBIC rules as a fuel-fired unit.
Does a large water heater need an Alabama permit and inspection?
A water heater rated at 200,000 Btu per hour or more is classed as an HLW boiler in Alabama, and the state requires an installation permit for water heaters over 200,000 Btu or over 120 gallons. Hot water supply boilers that stay at or under 200,000 Btu per hour, 210 F and 120 gallons, with ASME and National Board relief valves, are excepted from the Act.
Can a boiler keep running in Alabama after an inspector finds it unsafe?
A boiler found unsafe stops: the inspector notifies the owner of the repairs needed and the chief inspector, operation ceases until the corrections are made, and any certificate in force is suspended. The state may also issue a written cessation order. After a reinspection confirms the repair, the certificate is restored. A boiler that cannot be made safe is condemned and its stamped stars are marked with an X.
What records should an Alabama plant keep after a boiler repair?
An Alabama plant should keep the NBIC repair report, normally Form R-1, the welding procedure and welder qualification records, material certificates, examination and pressure test records, the inspector’s acceptance, any new safety valve data and the posted certificate. Paul Industries hands these over in one package and files the copies the NBIC requires with the chief inspector.
How is a pulp mill or biomass boiler repair planned in Alabama?
A pulp mill or biomass boiler repair is planned around the mill’s outage, with tube thickness surveys, refractory and waterwall inspection, and the repair procedures agreed with the insurer’s inspector before the boiler comes off line. Scaffolding, confined space entry and hot work permits are arranged in advance, and the scope is ranked so the most critical tubes are repaired first if the outage shortens.
Does Paul Industries install new boilers in Alabama as well as repair them?
Paul Industries supplies and installs new and replacement boilers in Alabama, from packaged firetube and watertube units to electric and modular hot water boilers, together with burners, controls, feedwater and condensate equipment and boiler room piping. The work covers the state Request to Install, the Manufacturer’s Data Report, the Alabama serial number and the first certificate inspection.
What should an Alabama facility send for a boiler repair quote?
Send the boiler make, model and year, the National Board and Alabama serial numbers, nameplate pressure and rating, fuel, the latest inspection report, photographs of the damage or a description of the fault, the outage window and whether temporary steam or heat is needed. Paul Industries replies with a repair scope and price and, for major damage, a budget figure for replacement.
Have an Alabama boiler down or due for its certificate inspection?
Send the boiler data, the latest inspection report and a description of the fault or damage. Call 201-450-8280 or request a quote.
