Paul Industries is a US process equipment contractor for the Netherlands that engineers process systems for Dutch plants, builds the skids, pressure vessels, tanks and piping in its US shop, tests them before shipment to Rotterdam, and then installs, starts up and commissions them at the plant or supervises the plant’s installation team. Paul Industries runs these projects from its headquarters on Shore Drive in Kilmarnock, Virginia. Refineries and chemical producers in the Rotterdam port area, plants on the Chemelot site at Geleen and biopharmaceutical manufacturers around Leiden receive equipment designed to the Pressure Equipment Directive as the Netherlands applies it, wired for 400 V, 50 Hz and to NEN 1010 practice, and documented for EU GMP where medicines are made.

Request a quote or call 201-450-8280

Headquarters 256 Shore Drive, Kilmarnock, Virginia
Dutch pressure law Warenwetbesluit drukapparatuur 2016, implementing PED 2014/68/EU
Power 50 Hz, 230/400 V
Low-voltage code NEN 1010, based on IEC 60364
EU duty on US industrial goods 0% under Regulation (EU) 2026/1455 since July 1, 2026
Main port Rotterdam, about 10 to 14 days from the US East Coast
Reviewed November 2026

What does a US process equipment contractor for the Netherlands supply?

A US process equipment contractor for the Netherlands supplies the engineering, the fabricated equipment, the test evidence and the field work that turn a Dutch plant’s process requirement into a running system, along with the PED conformity file and the records Dutch inspection rules call for once the equipment is in use. Paul Industries works under one contract for the whole chain.

The hardware covers what Dutch chemical, refining and life sciences sites buy: pressure vessels and receivers, fabricated tanks for storage and blending, process piping and spools, chemical injection and transfer skids, purified water and WFI systems, bioreactor installation with its utilities, and turnkey process systems integrating several of them.

Dutch buyers pick from three delivery routes. With supply and supervision, Paul Industries designs, builds, tests and ships the equipment, then directs the plant’s contractor team through setting and tie-ins. With design-build, Paul also engineers the unit’s layout, utilities and interfaces with the existing plant. With complete installation, Paul Industries sets, connects, starts up and qualifies the system on site and hands over a working unit with its turnover dossier.

Where is the chemical industry in the Netherlands, and which plants buy process systems?

The chemical industry in the Netherlands is concentrated in a handful of large clusters: the Rotterdam port area, the Chemelot site at Geleen in Limburg, Moerdijk in North Brabant, Zeeland’s Sloe and Terneuzen area, and the northern sites around Delfzijl. Each cluster shares pipelines, utilities and services, so a new process unit there connects into an existing industrial web. The plants named on this page are market facts about where Dutch demand sits.

The Port of Rotterdam industrial cluster

The Port of Rotterdam industrial cluster combines refining, bulk chemicals, tank storage and energy in Botlek, Pernis, Europoort and the Maasvlakte. The port authority counts 45 chemical companies and five oil refineries in its petrochemical cluster, and the five refineries have a combined distillation capacity of 58 million tonnes a year. Inside the Port of Rotterdam chemical cluster, pipelines link producers to one another and to the tank terminals, and Rotterdam chemical companies buy pressure vessels, heat exchangers, chemical injection skids, flare and vent piping, and equipment for hydrogen, carbon capture and biofuel projects as the port area moves away from fossil feedstocks. Equipment for that service is often installed in hazardous areas, so ATEX classification and explosion-protected electrical design are fixed at the start. Plants pursuing biofuels and renewable gas work in the port area draw on the same pressure equipment and piping scope.

Chemelot and the inland chemical sites

Chemelot, the integrated site at Sittard-Geleen in South Limburg, covers about 800 hectares and hosts producers such as SABIC, OCI Nitrogen and Arlanxeo alongside research and start-up companies. Chemical companies in the Netherlands outside the port areas follow the same pattern of shared utilities and site rules, and they buy reactor modules, solvent recovery units, scrubbers and process piping for chemical manufacturing. The Dutch chemical industry as a whole works to the same European directives, which simplifies documentation for a supplier that knows them.

Biotech companies in the Netherlands and the Leiden Bio Science Park

Biotech companies in the Netherlands cluster most heavily at the Leiden Bio Science Park, with further hubs in Utrecht, Amsterdam, Nijmegen and Oss. Janssen Biologics runs a biopharmaceutical production and laboratory site in Leiden that makes bulk active ingredients and is expanding next to its existing plant. At the Leiden Bio Science Park, Eli Lilly has announced a planned 3 billion dollar oral medicine plant in Katwijk, with the permit application filed in April 2026. Dutch biotech companies and their contract manufacturers buy media and buffer preparation skids, WFI and clean steam systems, CIP systems and process tanks for biotech production.

Dutch industrial clusters and the equipment their plants buy
ClusterMain activityTypical process equipment
Rotterdam port (Botlek, Pernis, Europoort, Maasvlakte)Refining, bulk chemicals, tank storage, hydrogen and biofuelsPressure vessels, exchangers, injection skids, ATEX-rated packages, piping
Chemelot, Sittard-GeleenBase and performance chemicals, fertilizers, polymersReactor modules, solvent recovery, scrubbers, utility piping
Moerdijk and ZeelandPetrochemicals and chemical intermediatesStorage tanks, transfer skids, process piping
Leiden Bio Science ParkBiologics, vaccines, oral solid dose under developmentWFI, clean steam, media and buffer skids, CIP, process tanks
Amsterdam, Utrecht, Oss, NijmegenBiotech, pharmaceutical development and manufacturePurified water, pilot-scale skids, cleanroom utilities

Food, dairy and data center plants

Food, dairy and data center operators make up the third group of Dutch buyers, alongside chemicals and life sciences. Dairy and food plants buy sanitary process piping, CIP systems, process tanks and water treatment built to hygienic design rules, while the data center campuses around Amsterdam and in the north of the country buy chilled water plants, heat rejection and liquid cooling distribution. Paul Industries designs and builds those systems in the United States to the same EU directives and Dutch installation practice as a chemical unit, with sanitary welds and surface finish records where food contact applies.

Why Dutch plants buy from a US process equipment builder

Dutch plants buy process systems from a US builder for capacity, schedule and continuity. Many Dutch sites belong to American parent companies whose engineering standards were written around ASME, ASME BPE and US instrument practice, and a US builder that also knows the PED route delivers equipment that meets both the corporate standard and Dutch law. Fabrication slots in the United States add capacity when European shops are full, and a builder that designs, fabricates, tests and commissions keeps the whole system under one contract with one set of records.

Which pharmaceutical companies in the Netherlands buy GMP process systems?

The pharmaceutical companies in the Netherlands that buy GMP process systems are biologics and vaccine producers, generic and specialty manufacturers, and contract development and manufacturing organizations, with the biggest current investments around Leiden. The pharmaceutical industry in the Netherlands also hosts the European Medicines Agency in Amsterdam, which keeps regulatory expertise close to the plants. Equipment for these sites is documented for inspection by the Health and Youth Care Inspectorate (IGJ), a PIC/S participating authority since November 1995, against the EU GMP Guide and its Annex 1 for sterile products. Water systems follow the European Pharmacopoeia, and stainless product-contact parts follow ASME BPE with weld maps, borescope records and surface finish readings for pharmaceutical plants.

Which Dutch rules apply to pressure equipment, machinery and electrical installations?

Dutch rules for process equipment combine EU product law with national rules for use: the Pressure Equipment Directive through the Warenwetbesluit drukapparatuur 2016, the Machinery Directive and from 2027 the Machinery Regulation, the Low Voltage, EMC and ATEX directives, and the NEN 1010 standard for the fixed electrical installation. The table shows what each asks of a skid or vessel and its documents.

Dutch and EU rules that shape a process system for the Netherlands
RuleScopeWhat the equipment and its file need
PED 2014/68/EU and Warenwetbesluit drukapparatuur 2016Design, manufacture and conformity of equipment above 0.5 barCategory, conformity assessment module, CE marking, EU declaration of conformity, instructions
Warenwetbesluit drukapparatuur 2016, use phaseDesignated pressure equipment in serviceInspection before first use, periodic re-inspection, records of both
Arbobesluit article 7.4aPressure equipment outside the designated groupsDuty of care with an inspection regime suited to the risk
Machinery Directive 2006/42/EC, then Regulation 2023/1230 from January 20, 2027Skids and assemblies with moving partsRisk assessment, technical file, declaration, CE marking
ATEX Directive 2014/34/EUEquipment for explosive atmospheresEquipment group and category matched to the plant’s zone classification
NEN 1010 and EN 60204-1Fixed installation and machine electrical equipmentPanels and field wiring designed for TN systems at 400 V, 50 Hz
EU GMP Guide and Annex 1Medicines manufactureQualified design, traceable materials, validated cleaning and sterilization

Low Voltage, EMC and ATEX files for a Dutch skid

A Dutch skid’s electrical file covers three EU directives besides the machinery rules: the Low Voltage Directive 2014/35/EU for electrical safety, the EMC Directive 2014/30/EU for interference from drives and instruments, and the ATEX Directive 2014/34/EU wherever the equipment sits in a classified zone. Paul Industries selects drives with EMC filtering suited to the plant’s network, routes and screens signal cables to IEC practice, and records every ATEX component with its marking and certificate data in the turnover dossier.

The Pressure Equipment Commodities Act Decree in practice

The Pressure Equipment Commodities Act Decree 2016 (Warenwetbesluit drukapparatuur 2016) implements the PED in Dutch law for the design and conformity of pressure equipment, and it adds rules for the use phase. Designated equipment is inspected before it is put into use and re-inspected at set intervals, and each inspection record carries the inspection date and the year of the next re-inspection. Equipment outside the designated groups falls under the general duty of care in the Arbobesluit. Paul Industries supplies the design data, calculations, material certificates, test reports and operating instructions that the first-use inspection works from, so the Dutch plant puts the equipment into service without a documentation gap.

For a vessel designed to ASME Section VIII, the PED route covers materials accepted under the directive, welding procedures and welder qualifications, non-destructive testing and the final test, and Paul Industries plans that route before ordering material. Equipment then carries its CE marking and EU declaration of conformity on arrival in Rotterdam.

What is the voltage in the Netherlands, and how does it change a skid?

The voltage in the Netherlands is 230 V between phase and neutral and 400 V between phases, at 50 Hz, and most process motors run directly on the 400 V three-phase supply while large plants take power at medium voltage. Netherlands voltage and frequency therefore differ from the 480 V, 60 Hz supply many American skids are built for.

The frequency change matters most for rotating equipment. A motor wound for 60 Hz runs about 17 percent slower at 50 Hz, so pumps, agitators and fans are selected on 50 Hz curves from the first design pass, and variable frequency drives are set for 50 Hz base speed. Panels follow EN 60204-1 with IEC-rated components, and the field installation they connect to is designed to NEN 1010, the Dutch implementation of IEC 60364, which the Dutch building regulations reference. In Rotterdam and Chemelot hazardous areas, motors, instruments and junction boxes carry ATEX marking matched to the plant’s zone drawings.

Shipping process equipment to the Netherlands from the US East Coast

Process equipment reaches the Netherlands by direct sailing from a US East Coast port to Rotterdam, the main Dutch gateway, in about 10 to 14 days port to port, and then moves inland by truck, barge or rail to the plant. Rotterdam’s deep-sea terminals handle containers, flat racks and breakbulk, so oversize skids and vessels land close to the Botlek and Europoort plants that use them.

Inland legs depend on the site. Port-area plants sit a short truck move from the quay, while Chemelot and other inland sites are reached by barge on the Dutch waterways or by road, and oversize loads move under exceptional transport permits on planned routes. Paul Industries fixes the shipping envelope in design, splits large systems at flanged joints where a route requires it, and books freight once crate dimensions are final.

Preservation for a Dutch delivery is planned for a North Atlantic crossing and for storage in a humid, salty port climate, since equipment sometimes waits at the quay or on site before installation. Stainless internals are dried and sealed under nitrogen or with desiccant, carbon steel surfaces are coated or wrapped, and crates are built from heat-treated wood marked to ISPM 15. Each crate carries lift points, center of gravity marks and a packing list matched to the Dutch site’s receiving inspection, and a preservation log tells the plant what to check if installation is delayed.

Customs, duty and VAT for US equipment entering the Netherlands

US-origin industrial goods enter the European Union at zero customs duty under Regulation (EU) 2026/1455, which entered into force on July 1, 2026 and runs until December 31, 2029 unless extended, with origin decided by the EU’s non-preferential rules. Dutch import VAT is charged at the standard 21 percent. With an Article 23 licence, the importer reports that VAT on its periodic return rather than paying it at the border, and companies established outside the Netherlands use a fiscal representative for it.

Incoterms 2020 choices for a Dutch delivery
IncotermWhere Paul Industries hands overWhat the Dutch plant handles
FCA US port or Paul’s shopExport cleared and loaded onto the plant’s carrierOcean freight, insurance, Dutch import declaration, VAT
CIF RotterdamOn board the vessel at the US port, with freight and insurance paid to RotterdamUnloading, import clearance, inland freight, VAT
DAP plant siteAt the Dutch plant, ready for unloadingImport clearance and VAT, often through an Article 23 licence
DDP plant siteAt the Dutch plant, import cleared with VAT paidUnloading and site acceptance

How does a project for a Dutch plant run with Paul Industries?

A project for a Dutch plant runs through nine steps with Paul Industries, and the Dutch-specific decisions on PED category, ATEX zones, NEN 1010 interfaces, language and freight are made in the first two. The table shows each step and the record it leaves.

Steps of a process equipment project for the Netherlands
StepDutch focusRecord delivered
1. Code and site reviewPED category and module, use-phase inspection needs, ATEX zones, plant standards, document languageCode basis and inspection list
2. EngineeringMetric drawings, DN piping, 400 V 50 Hz design, plant specification sheetsP&IDs, layouts, calculations, data sheets
3. Fabrication in the US shopPED-acceptable materials and qualified weldingMaterial certificates, weld maps, NDT reports
4. Factory acceptance testPressure, function and alarm tests, Dutch team in the shop or on videoSigned FAT protocol and punch list
5. Crating and shippingISPM 15 crates, routing to Rotterdam and the inland legInvoice, packing list, bill of lading
6. Installation or supervisionPlant work permits, safety passports, method statements in Dutch or EnglishInstallation and tie-in records
7. Start-upLine flushing, instrument loop checks, trial runs on the plant’s steam, water and powerStart-up report with setpoints
8. Commissioning and qualificationSAT, and IQ and OQ for GMP plantsExecuted protocols, deviations
9. Handover and serviceTraining, spares, support for the first-use inspectionTurnover dossier, as-builts, manuals

Validation work for GMP sites is written during design by Paul Industries’ validation and commissioning team, so the IQ and OQ at the Dutch site test what transport and installation affect and lean on the FAT for the rest. Manuals, labels and safety information are supplied in Dutch, with English engineering documents alongside for plant engineering teams that work in English.

Work at Dutch chemical and refining sites runs under the plant’s own permit-to-work system, toolbox meetings and site safety rules, and Paul Industries sends method statements, lifting plans and work packages ahead for the plant’s approval so the field team starts on the agreed day.

Who builds process systems for plants in the Netherlands?

Paul Industries builds process systems for plants in the Netherlands, from single skids and pressure vessels to complete water, CIP, tank and piping packages for chemical, refining, biotech and pharmaceutical producers, and stays responsible from design through Rotterdam delivery to start-up and qualification at the Dutch site. One firm engineers, fabricates, tests and commissions the system, so the plant has one point of accountability for performance and records. The same delivery model serves plants in Belgium and Germany, and every country Paul takes work in is listed on the international projects page.

What drives the cost of a process system delivered to the Netherlands?

The delivered cost of a process system for a Dutch plant depends on six items beyond the equipment: ocean and inland freight, crating and preservation, PED and ATEX documentation, import VAT handling under the chosen Incoterm, language work, and the installation route. Paul Industries lists each separately in its quote.

Freight. Containers cost less than flat racks or breakbulk, and the inland leg to Chemelot or a northern site adds more than delivery to a Rotterdam plant. Crating. ISPM 15 crates, desiccant, vapor barrier and nitrogen blankets protect stainless internals and instruments. Code documentation. PED conformity assessment for higher categories, ATEX equipment selection and data for the first-use inspection add engineering hours. Taxes. Customs duty on US industrial goods is zero under the 2026 EU regulation, and import VAT at 21 percent is reported through the plant’s return or included by Paul Industries under DDP. Language. Dutch manuals and safety information are prepared for the site. Installation route. Supervision of the plant’s contractors uses fewer Paul field hours than complete installation, which places start-up responsibility with the builder. Each quote is priced in US dollars: a budget figure from comparable scope comes first, and the firm price follows when drawings, the Dutch site and the delivery terms are settled.

Paul Industries for Dutch chemical, refining and biopharmaceutical plants

Paul Industries, at 256 Shore Drive in Kilmarnock, Virginia, delivers process systems to plants across the Netherlands: it engineers each system, fabricates its skids, vessels, tanks and piping in the United States, proves it in a factory acceptance test, ships it to Rotterdam and onward to the site, and then sets, starts up and commissions it or supervises the plant’s installers through each step. Every system arrives built and documented to the PED as Dutch law applies it, to NEN 1010 and ATEX practice, and to EU GMP where medicines are made, with as-builts, weld records and validation documents in the turnover dossier. Send the scope, plant location and preferred Incoterm to request a quote.

Standards referenced: EU Pressure Equipment Directive 2014/68/EU · Warenwetbesluit drukapparatuur 2016 (Pressure Equipment Commodities Act Decree 2016) · Arbobesluit article 7.4a · EU Machinery Directive 2006/42/EC · EU Machinery Regulation 2023/1230 · EU Low Voltage Directive 2014/35/EU · EU EMC Directive 2014/30/EU · ATEX Directive 2014/34/EU · NEN 1010 · EN 60204-1 · EU GMP Guide (EudraLex Volume 4) and Annex 1 · PIC/S GMP Guide · European Pharmacopoeia · ASME Boiler and Pressure Vessel Code Section VIII · ASME BPE · Regulation (EU) 2026/1455 · Incoterms 2020 · ISPM 15

Frequently asked questions

What is the voltage in the Netherlands, and do US-built motors run on it?

Dutch industrial supply is 400 V between phases and 230 V phase to neutral at 50 Hz, with medium voltage connections at large plants, so a motor wound for a 480 V, 60 Hz American plant is replaced or rewound. Process equipment for the Netherlands therefore uses motors, drives and transformers rated for 50 Hz and 400 V, and pump selections are made on 50 Hz curves. Paul Industries designs skids for that supply from the start and builds panels to EN 60204-1.

How long does shipping take from the US to the Netherlands for a process skid?

A crated process skid sails from a US East Coast port to Rotterdam in about 10 to 14 days port to port on direct services. Port handling, customs clearance and the inland leg to the plant add days, and flat-rack or breakbulk cargo can wait for a suitable sailing. Paul Industries books freight once crate dimensions are fixed and sets the FAT date to meet the chosen vessel.

Which US contractor builds pressure vessels for Rotterdam refineries?

Paul Industries builds pressure vessels and receivers for plants in the Rotterdam port area, designed to the PED route with ASME Section VIII calculations where the plant uses them, CE marked and delivered with the EU declaration of conformity. Vessels for refinery and petrochemical service ship with full material traceability, NDT reports and the data the Dutch first-use inspection needs.

Does a skid for Chemelot need ATEX-rated equipment?

A skid for Chemelot needs ATEX-rated equipment wherever the plant’s zone classification places it in an explosive atmosphere, which is common in chemical production areas at Geleen. Motors, instruments, junction boxes and some mechanical parts are then selected for the matching equipment group and category under Directive 2014/34/EU. Paul Industries takes the zone drawings at the code review and designs the skid to them.

Who builds WFI and clean steam systems for biologics plants in Leiden?

Paul Industries builds WFI and clean steam systems for biologics plants in Leiden and across the Leiden Bio Science Park, covering generation, storage, distribution loops and clean steam headers. Systems are designed to the European Pharmacopoeia and EU GMP Annex 1, fabricated and tested in the United States, shipped to Rotterdam and qualified at the site with IQ and OQ protocols.

What does the Dutch first-use inspection need from the equipment supplier?

The inspection before first use under the Warenwetbesluit drukapparatuur 2016 works from the equipment’s conformity documents: the EU declaration of conformity, design calculations, drawings, material certificates, welding and NDT records, pressure test certificates and operating instructions, together with the installed safety devices. Paul Industries assembles those records in an indexed dossier and supports the plant through the inspection.

Can a vessel built to ASME be used at a Dutch chemical plant?

A vessel built to ASME Section VIII is used at a Dutch chemical plant once it completes the PED conformity route for its category, which covers materials, welding procedure and welder qualifications, NDT, the final test and CE marking. ASME remains a valid design basis inside that route. Paul Industries plans the PED path before material is ordered so the vessel ships ready for Dutch service.

What customs duty applies to US process equipment imported into the Netherlands?

US-origin industrial goods, including process equipment, enter the EU at zero customs duty under Regulation (EU) 2026/1455, in force since July 1, 2026 and set to run until the end of 2029. Dutch import VAT of 21 percent still applies, and with an Article 23 licence the importer reports it on its VAT return instead of paying at the border. Paul Industries states the Incoterm and tax treatment in every quote.

Are manuals supplied in Dutch for plants in the Netherlands?

Manuals, labels and safety information for Dutch plants are supplied in Dutch, with English engineering documents alongside where the plant’s engineering, maintenance or validation teams work in English, which is common at multinational sites in Rotterdam and Leiden. Paul Industries agrees the document list and languages at the code review so translations are ready when the equipment ships.

Does Paul Industries install equipment at Dutch plants or supervise the plant's contractors?

Paul Industries does both, decided per project. Under complete installation Paul sets, connects, starts up and qualifies the system at the Dutch site. Under supervision, the plant’s contractor team carries out the physical work while Paul directs setting, tie-ins, start-up and the site acceptance test. In both cases the firm that built and tested the equipment commissions it.

How are oversize skids moved from Rotterdam to inland plants such as Chemelot?

Oversize skids move from Rotterdam to inland plants such as Chemelot by barge on the Dutch waterways where a quay is close to the site, or by road under an exceptional transport permit on an approved route. Weight and dimensions decide between them. Paul Industries checks the route during design and splits systems into transportable modules where the route sets a limit.

Which Incoterm suits a first equipment order from a Dutch plant?

Many Dutch plants start with DAP to the plant gate, under which Paul Industries bears freight cost and transit risk as far as the site, while the plant clears import and handles VAT, often through an Article 23 licence. DDP suits buyers who want one landed price, and FCA suits plants with their own forwarder at US ports. Paul shows the price under each rule the buyer asks for.

Who supplies process piping for hydrogen and carbon capture projects in the Rotterdam port area?

Paul Industries supplies process piping, spools, pressure vessels and skids for hydrogen, carbon capture and biofuel projects in the Rotterdam port area, designed to the PED and the plant’s piping specifications, with ATEX-rated components where zones require them. Spools are fabricated, tested and documented in the US shop, then installed and pressure tested on site by Paul Industries or under its supervision.

What does a GMP inspector in the Netherlands look for in a new process system?

Inspectors from the Health and Youth Care Inspectorate assess process systems against the EU GMP Guide, including Annex 1 for sterile products: a risk-based design rationale, qualified equipment, traceable product-contact materials, validated cleaning and sterilization, and data integrity in automated controls. Paul Industries supplies specifications, test records and executed protocols so the plant shows that evidence during inspection.

Can a Dutch team witness the factory acceptance test remotely?

A Dutch team can witness the factory acceptance test in the US shop or remotely by live video, and many teams attend the integrated sequence tests in person and follow routine checks remotely. With Dutch clocks six hours ahead of New York for most of the year, remote witness sessions are set for the Dutch afternoon. Paul Industries posts data and photographs as each step closes.

What service do Dutch plants receive after start-up?

After start-up, Paul Industries serves Dutch plants with scheduled service visits, remote troubleshooting based on the drawings, programs and test records it already holds, and spare parts shipped from the United States. The handover spares list is sized for transatlantic lead times, and Paul supplies the records the plant needs for periodic re-inspection of its pressure equipment.

What do biotech plants around Utrecht and Oss buy from a US process contractor?

Biotech and pharmaceutical plants around Utrecht and Oss buy purified water systems, pilot and clinical-scale process skids, CIP systems, process tanks and clean utility piping, often sized for development and launch volumes. Paul Industries designs and builds these systems in the United States to EU GMP and European Pharmacopoeia requirements and installs and qualifies them at the Dutch site.

Planning a process unit for a plant in the Netherlands?

Share the process duty, the Dutch site, any ATEX zones, the plant’s document language and the Incoterm you prefer, and Paul Industries replies with the PED and inspection basis, a route through Rotterdam and a budget range to plan against. Call 201-450-8280 or request a quote.