Paul Industries provides pressure vessel fabrication in Virginia for chemical, food, pharmaceutical and power plants, designing and building vessels to ASME Section VIII and handing them over with the data report and National Board registration the Commonwealth requires before a vessel goes to work. Paul is headquartered at 256 Shore Drive in Kilmarnock, Virginia, and delivers receivers, reactors, jacketed process vessels, separators, blowdown and flash tanks and replacement vessels to plants from Hopewell and Petersburg to Hampton Roads, Northern Virginia and the Shenandoah Valley.

Request a quote or call 201-450-8280

Headquarters 256 Shore Drive, Kilmarnock, Virginia
Construction code ASME BPVC Section VIII
State registration National Board and DOLI, unless the vessel is exempt
Before first use Manufacturer's Data Report filed with the chief inspector
Certificate inspection Every two years
Exempt by pressure Unfired vessels at 15 psi or less, any size
Reviewed November 2026

What does Virginia require before a new pressure vessel goes into service?

Virginia requires a regulated pressure vessel to be designed, built, inspected, stamped and installed to the applicable ASME Code, registered with the National Board and with the Department of Labor and Industry, and documented to the chief inspector before it is first operated. Those requirements come from the Boiler and Pressure Vessel Safety Act and its regulation, 16VAC25-50, which DOLI’s Boiler and Pressure Vessel Safety Division administers.

Owners searching for the Virginia boiler and pressure vessel code are usually looking for two documents at once. The statute, the Virginia Boiler and Pressure Vessel Safety Act, sets which vessels are regulated, which are exempt and what happens when a certificate lapses. The regulation adopts the ASME Boiler and Pressure Vessel Code for construction and the National Board Inspection Code for work on vessels already in service. Together they are what a fabricator’s drawings, data report and nameplate are checked against in this state.

Virginia steps for a new code pressure vessel
StepWhat the Virginia rules requireRecord the owner receives
Design and constructionThe applicable ASME Code, usually Section VIII Division 1, applied by design, fabrication and inspection during constructionDesign calculations, drawings and the material test reports
StampingASME certification mark with the U designator, plus the National Board stamp; UM miniature vessels are excepted from the National Board stampA nameplate with the National Board number, MAWP, temperature and test data
RegistrationNational Board registration and registration with DOLI unless the vessel is exemptThe registered data report
Before operationThe Manufacturer’s Data Report, carrying the signatures of the manufacturer’s representative and a National Board commissioned inspector, is filed with the chief inspectorForm U-1 or U-1A
After installationA Commonwealth serial number is assigned after installation or the first certificate inspection; stamping must stay visible through insulation and paintThe VA number and the first inspection certificate
Equivalent or out-of-state constructionAccepted only when the application to the chief inspector is made before construction startsThe chief inspector’s written acceptance

The last row catches buyers who source a vessel built to another standard. Non ASME pressure vessels can run in Virginia only under a variance granted through section 40.1-51.19 of the Act, which demands extensive documentation, and a secondhand vessel needs the chief inspector’s approval before it is installed. Paul Industries designs and builds Virginia vessels to the ASME Code from the start, so the registration, data report and nameplate are ready for the inspector on the day the vessel is set.

Which pressure vessels are exempt in Virginia?

Section 40.1-51.8 of the Code of Virginia exempts several classes of pressure vessel from the Act, mainly by operating pressure, internal volume, inside diameter or contents. A vessel inside one of these limits needs no Virginia registration or certificate inspection, though other rules may still call for ASME construction.

Virginia pressure vessel exemptions under section 40.1-51.8
Exempt classLimits in the ActTypical plant example
Low-pressure unfired vessels15 psi or less operating pressure, no size limitAtmospheric and near-atmospheric process tanks, low-pressure filters
Small air receiversAir only, up to 8 cubic feet and 175 psi operating pressurePoint-of-use receivers on packaging lines
Small vessels by volumeUp to 5 cubic feet at 250 psig, or up to 1.5 cubic feet at 600 psigSmall surge pots, accumulators and sample cylinders
Small-diameter vesselsUp to 6 inches inside diameter, with no pressure limitPipe-shell filters, strainers and small separators
Water vessels with an air cushionWithin the Act’s 300 psi, 210 F and 120-gallon limitsHydropneumatic and expansion tanks
LP-gas containersStationary ASME propane containers up to 2,000 gallons, inspected at least every five years with records keptForklift fuel and backup heating storage
Utility substation vesselsIn an enclosed, locked substation owned or operated by an electric utilityBreaker and transformer gas vessels

An exemption from the Virginia Act is narrower than it looks. OSHA’s rule for compressed air receivers, 29 CFR 1910.169, still expects ASME Section VIII construction with a drain at the low point, a gauge and a safety valve, and a vessel inside a covered chemical process still falls under process safety management. Insurers and corporate engineering standards usually ask for a U-stamped vessel whatever its size. Paul Industries builds to the ASME Code by default and tells the owner, item by item, which vessels on a project fall under the Act and which sit inside an exemption.

How pressure vessel fabrication in Virginia runs from data sheet to VA number

Pressure vessel fabrication in Virginia follows the ASME sequence any code shop uses, with three Virginia-specific checkpoints added: the exemption check at the data sheet, the registration at completion and the filing with the chief inspector before first use. The steps below are the order in which Paul Industries carries a Virginia vessel.

The work starts with a data sheet: contents, design pressure and any vacuum or external pressure, design temperature and minimum design metal temperature, corrosion allowance, nozzle schedule, supports, insulation and the examination level. For lethal contents, which some chemical services involve, Section VIII requires full radiography of butt welds and postweld heat treatment of carbon and low-alloy steel, so the contents decision is a cost decision made on day one. Calculations follow for shell and head thickness, nozzle reinforcement, wind and seismic loads on the supports, and the hydrostatic test. Outdoor vessels and their foundations also go through the building official under the Virginia Uniform Statewide Building Code, which draws its structural loads from the International Building Code.

Fabrication runs under qualified welding procedures and welders to ASME Section IX, with material traceability from the mill certificate to the weld map. After examination, a Division 1 vessel is hydrostatically tested at no less than 1.3 times MAWP multiplied by the lowest stress ratio, or pneumatically at 1.1 times where water cannot be used, with the test witnessed by the National Board commissioned inspector. The vessel is stamped, the data report signed and registered, and the package goes to the owner with the drawings and test records. Paul then sets, pipes and starts up the vessel, files the data report with the chief inspector and books the first certificate inspection that brings the VA number. Stainless vessels for pharmaceutical and food duty are cleaned and passivated before handover through passivation services in Virginia.

Virginia pressure vessel inspection requirements after installation

Virginia pressure vessel inspection requirements call for a certificate inspection every two years, with an internal inspection where the contents corrode the vessel and an external inspection otherwise. The inspector comes from the owner’s insurance carrier or is a contract fee inspector authorized by DOLI, because the Department does not run routine inspections itself.

Pressure vessel internal inspection requirements in Virginia are practical as well as legal. The regulation expects a vessel prepared for an internal inspection to have its manhole and handhole covers removed, to be cleaned and ventilated, to be isolated so conditions inside are safe, and to have linings or coverings removed where the inspector asks. Paul designs Virginia vessels for that day: manways sized for entry, davits on heavy covers, drains at true low points, isolation blinds on every process nozzle and insulation detailed to come off around the nameplate and inspection points.

Who inspects pressure vessels in Virginia?

Three kinds of inspector look at a Virginia vessel over its life. During construction, a National Board commissioned inspector witnesses the hydrostatic test and signs the data report. In service, an inspector from the insurance carrier or a contract fee inspector performs the biennial certificate inspection. A plant can instead register as an owner-user inspection agency under section 40.1-51.11:1, with Board approval, a fee, a $5,000 bond and an annual statement; vessels inspected by an approved owner-user agency need no inspection certificate, and their intervals are set by agreement with the Commissioner. That route suits large chemical sites, such as the plants along the James River at Hopewell, that already run their own mechanical integrity programs.

Who looks at a Virginia pressure vessel, and what they sign
StageInspectorGoverning documentRecord
Fabrication and shop testNational Board commissioned inspectorASME Section VIIISigned U-1 or U-1A and the nameplate stamping
First certificate inspectionInsurance carrier or contract fee inspector16VAC25-50Inspection report, certificate and VA number
Biennial recertificationInsurance carrier or contract fee inspectorSection 40.1-51.10 and 16VAC25-50-30Renewed certificate posted at the vessel
Owner-user programApproved owner-user inspection agencySection 40.1-51.11:1 and the agency’s agreementAgency inspection records in place of a certificate
Repair or alterationInspector with the appropriate endorsementNational Board Inspection Code Part 3R-1 Report of Repair or R-2 Report of Alteration

Federal rules sit alongside the state Act. Virginia runs its occupational safety program as a state plan through the same Department, and under process safety management, 29 CFR 1910.119(j), pressure vessels and storage tanks in a covered process need inspection and testing to recognized and generally accepted good engineering practice, which for in-service vessels is usually API 510. A Hopewell or Petersburg plant can therefore hold a current Virginia certificate and still owe its own integrity inspections, and Paul builds and documents each vessel so that both programs start from the same baseline thickness readings and drawings.

Designing vessels for Virginia chemical, food, pharmaceutical and power plants

Vessel design for Virginia plants changes most with the industry the vessel serves, because each industry brings its own contents, cleaning regime and documentation burden. The table below sets out the choices Paul Industries settles first for each.

Vessel design choices by Virginia industry
IndustryTypical vesselsMaterial and finishWhat drives the design
Chemical (Hopewell and the James River)Reactors, separators, knockout drums, receiversCarbon steel with corrosion allowance, 304L, 316L or higher alloysLethal or flammable contents, full radiography and PWHT where required, process safety records
Pharmaceutical (Petersburg, Richmond, Albemarle County)Jacketed process vessels, WFI and clean steam vessels, pressure filters316L with ASME BPE surface finishDrainability, cleanability, sterilization temperature and turnover documentation
Food and beverageJacketed kettles, cookers, pressure fermenters, CO2 and air receivers304 or 316 stainless with a sanitary finishCIP coverage, jacket pressure and vacuum on cool-down
Power and utilitiesBlowdown and flash tanks, air receivers, deaerator storage, feedwater heatersCarbon steel, with stainless where condensate is aggressiveThermal cycling, erosion at inlets and relief capacity

Jacketed vessels deserve a specific mention because the jacket is often the higher-risk side: a steam jacket at 150 psi around a shell held at full vacuum is two pressure chambers with two design cases, and both appear on the data report. For pharmaceutical work the vessel is only as good as the piping that serves it, so Paul carries the connections through process piping in Virginia and the weld documentation through industrial welding services in Virginia. Where a heat transfer duty is better served by a shell-and-tube unit than a jacket, Paul designs and builds that as well, as set out under heat exchangers.

Repairing, rerating and altering vessels already in Virginia service

Work on a pressure vessel already in Virginia service falls under the National Board Inspection Code, and 16VAC25-50 requires alterations, such as a new nozzle, a rerate or a change of service, to be performed under an ASME or “R” certificate scope with the change reported to the chief inspector. Repairs that restore the original design are recorded on Form R-1, while alterations go on Form R-2.

A rerate is the alteration Virginia owners ask about most when a process changes. It starts from the original U-1, a thickness survey and new calculations, and it ends with a pressure test where the inspector requires one, a new stamping or nameplate entry and the R-2 filed with the chief inspector. Adding a nozzle needs reinforcement calculations, a qualified procedure for the shell material and examination of the new welds. The Virginia regulation is strict on one older defect: a lap-seam crack along a longitudinal riveted joint means the vessel is shut down immediately, and patching is prohibited. Paul Industries scopes each alteration against the vessel’s records, carries out the welded work and test, and hands the owner the completed form for the file. Pressure tests on large or field-assembled vessels run through hydrostatic testing with the same records.

When repair stops making sense, a replacement vessel is usually the faster route to a clean certificate. Paul builds the replacement to the original nozzle orientation and support footprint so it drops into the existing piping, and boilers that share the same steam system are handled through boiler repair in Virginia.

Relief protection and pressure-reducing stations on Virginia vessels

Overpressure protection on a Virginia vessel is set by ASME Section VIII, and the Virginia regulation adds one specific rule for vessels fed through a pressure-reducing valve: where the piping or equipment on the low-pressure side cannot withstand the full initial pressure, one or more relief or safety valves must be fitted on the low-pressure side of the reducing valve (16VAC25-50-450). Plant air, nitrogen and steam headers feeding lower-rated vessels are where that rule most often applies.

The relief device is sized for the worst credible case, which is rarely the normal flow. For a vessel downstream of a reducing station, that case is usually the reducing valve failing wide open, so the relief valve has to pass the full flow the upstream supply can deliver at the vessel’s set pressure plus allowed overpressure. For a jacketed vessel, the jacket needs its own device sized for the steam or heat transfer fluid supply, and the shell needs protection for both the process case and, where the jacket can fail into it, the jacket case. Fire exposure often governs relief sizing for vessels holding flammable liquids, such as solvent receivers in chemical and pharmaceutical plants.

Paul Industries sizes and supplies the relief devices with the vessel, installs them with inlet and outlet piping that keeps pressure drop inside the limits the device needs to work properly, and records the set pressure, capacity and nameplate data in the turnover package so the certificate inspector can match each valve to the vessel’s MAWP. Where an existing vessel is being rerated, the relief devices are re-checked against the new rating as part of the same alteration.

Replacement vessels for Virginia plants that cannot stop for long

A replacement pressure vessel for a running Virginia plant is designed around the outage, not just the duty. The new vessel is built to the existing nozzle orientation, elevations, flange ratings and support footprint, using the old data report and a field survey of the piping, so it can be set and connected inside a short shutdown window.

Paul Industries surveys the existing vessel and its piping, confirms the old VA number and registration so the chief inspector’s records can be closed out for the retired vessel, and builds the replacement with any improvements the plant wants: a larger manway, better drains, a corrosion-resistant lining or an upgraded material. Before the outage, the new vessel is hydrotested, registered and staged with its relief devices, gaskets and bolting, and the rigging plan is set. During the outage the old vessel comes out, the new one goes in, connections are made up and tested, and the vessel is ready for its first certificate inspection. Plants with several aging vessels often bundle the replacements into one planned shutdown so each crane lift and each inspector visit covers more than one item.

How much does a pressure vessel cost in Virginia?

The cost of a pressure vessel built for a Virginia plant is driven by diameter, length and design pressure, which set wall thickness and weight, then by material, examination level, heat treatment, jackets and internals, and the documentation the end user expects. Freight, rigging and setting add to that, especially for vessels too large to ship on a standard trailer.

The state’s own cost items are small: an inspection certificate is $20 under 16VAC25-50-150, and a plant that registers as an owner-user inspection agency posts a $5,000 bond and pays an application fee and annual fee. The cost that matters is the one created by a vessel that arrives without what the inspector needs: a missing data report filing, a nameplate buried under insulation, or a vessel built outside the ASME Code that now needs a variance. Paul Industries prices those items into the quote so none of them appears later as an extra.

To get a budget figure, send the data sheet or a sketch with contents, pressure, temperature, volume, material, nozzle list and supports. Paul returns a budget range from comparable vessels, then a firm price once calculations confirm thicknesses and the examination plan. Supply-only delivery, design-build with installation, and complete installation with piping, insulation and start-up are all priced on request, and quality documentation follows the program described under quality and standards.

Who designs and fabricates pressure vessels for Virginia plants?

Paul Industries designs and fabricates pressure vessels for Virginia plants from its headquarters in Kilmarnock, and installs, tests and starts them up under the same contract. The work covers ASME Section VIII vessels in carbon steel, stainless and higher alloys: receivers, reactors, jacketed vessels, separators, filter housings, blowdown and flash tanks, and replacements matched to existing piping.

Atmospheric and low-pressure storage that sits outside the Act is built under tank fabrication in Virginia, and vessels that form part of a packaged system are built with their frames under structural steel fabrication or as process tanks where the duty is atmospheric. The national scope of Paul’s vessel work is set out on the pressure vessel fabrication page, and the full Virginia service list is on the Virginia page.

Pressure vessel work from Paul Industries in Virginia

Paul Industries, headquartered at 256 Shore Drive in Kilmarnock, designs, fabricates, tests, registers, installs and starts up ASME pressure vessels for Virginia plants, and repairs, rerates and replaces the vessels already in service. Every vessel leaves with its calculations, drawings, material records, data report and the paperwork the chief inspector expects. Call 201-450-8280 or request a quote with a data sheet or sketch of the vessel.

Standards referenced: ASME BPVC Section VIII Division 1 · ASME BPVC Section VIII Division 2 · ASME BPVC Section IX · National Board Inspection Code (NB-23) · Code of Virginia 40.1-51.5 et seq. (Boiler and Pressure Vessel Safety Act) · 16VAC25-50 Boiler and Pressure Vessel Regulations · OSHA 29 CFR 1910.119 · OSHA 29 CFR 1910.169 · API 510 · ASME BPE · Virginia Uniform Statewide Building Code

Frequently asked questions

Who fabricates pressure vessels for chemical plants in Hopewell, Virginia?

Paul Industries designs and fabricates ASME Section VIII vessels for chemical plants in Hopewell and along the James River, from receivers and knockout drums to reactors and separators in carbon steel, stainless and higher alloys. For lethal or flammable contents the vessel is built with the full radiography, heat treatment and records the code demands, then registered, set, tested and handed over with its data report. Call 201-450-8280 or request a quote.

Does Paul Industries build pressure vessels for plants in Hampton Roads and Northern Virginia?

Paul Industries builds and installs pressure vessels across Virginia, including Norfolk, Chesapeake, Newport News, Suffolk, Fairfax, Loudoun and Prince William, as well as Richmond, Charlottesville, Roanoke and the Shenandoah Valley. Food plants, utilities, data center support systems and manufacturing sites all use air receivers, blowdown tanks, filter housings and process vessels that fall under the Act, and each one is delivered with the paperwork that the first certificate inspection checks.

What is the Virginia pressure vessel code?

Virginia has no separate construction code of its own for pressure vessels. The Boiler and Pressure Vessel Safety Act and its regulation, 16VAC25-50, adopt the ASME Boiler and Pressure Vessel Code for how a vessel is designed and built and the National Board Inspection Code for repairs and alterations, then add Virginia’s registration, exemptions, certificate inspections and penalties on top. A vessel built to ASME Section VIII and registered with the National Board meets the construction side.

Who approves pressure vessels in the US, and what does Virginia add?

ASME writes the construction rules, a National Board commissioned inspector accepts the vessel during fabrication, and the National Board registers the data report. Each state then decides how vessels are regulated in service. Virginia adds registration with DOLI, filing of the data report with the chief inspector before operation, a VA serial number, and a certificate inspection every two years for vessels outside the exemptions in section 40.1-51.8.

How do OSHA pressure vessel inspection requirements apply in Virginia?

Virginia enforces workplace safety through its own state plan run by the Department of Labor and Industry, which applies the federal standards. Two matter most for vessels: 29 CFR 1910.169 expects compressed air receivers to be built to ASME Section VIII with a drain, gauge and safety valve, and 29 CFR 1910.119 requires mechanical integrity inspection of vessels inside covered chemical processes. Both run alongside the state certificate inspection rather than in place of it.

What are the ASME pressure vessel inspection requirements during fabrication?

Section VIII requires the vessel’s materials, welding procedures, welder qualifications, examinations and pressure test to be checked and accepted by a National Board commissioned inspector during construction. The inspector reviews calculations and drawings, sees fit-up and welds at agreed hold points, witnesses the hydrostatic or pneumatic test and signs the data report. On a Virginia vessel that signed report is what the chief inspector receives before the vessel operates.

What is the certificate inspection interval for a Virginia pressure vessel?

Regulated pressure vessels in Virginia receive a certificate inspection every two years. Vessels whose contents corrode them are inspected internally, and others externally, with an internal inspection at the inspector’s discretion where the construction allows. Plants approved as owner-user inspection agencies set intervals by agreement with the Commissioner, and plants under process safety management may need shorter intervals for their own integrity program.

Does a small air receiver need a Virginia certificate?

An air-only vessel of 8 cubic feet or less at no more than 175 psi operating pressure is exempt from the Virginia Act, as is any vessel up to 5 cubic feet at 250 psig. Larger receivers are regulated, need registration and receive a certificate inspection every two years. OSHA still expects every compressed air receiver to be built to ASME Section VIII with a drain, gauge and safety valve, so Paul Industries builds them that way regardless of size.

Can a vessel built outside the ASME Code be used in Virginia?

A non-ASME vessel can operate in Virginia only under a variance granted by the Board under section 40.1-51.19, and the application requires extensive documentation of design, materials and testing. Equipment built to an equivalent standard can be accepted by the chief inspector, but only when the application is made before construction begins. Replacing the vessel with an ASME-stamped unit is usually faster and cleaner, and Paul Industries quotes that option alongside.

Can a used pressure vessel be moved to a Virginia plant?

A secondhand vessel needs the chief inspector’s approval before it is installed in Virginia, and its fittings must meet the requirements for a new installation. The approval request draws on the original data report, the National Board registration, inspection history and a condition survey. Paul Industries assembles that package, inspects and thickness-tests the vessel, makes any repairs under the NBIC, and installs and tests it once approval is granted.

What happens to a pressure vessel nameplate when the vessel is insulated?

Virginia prohibits stamping from being concealed by insulation or paint, so the nameplate has to stay readable once the vessel is lagged. Paul Industries mounts the nameplate on a stand-off bracket clear of the insulation, or leaves a removable panel over it, and does the same for inspection openings the certificate inspector will need. Coating crews get the same instruction, so the stamping stays readable after every recoat.

How long does a new ASME vessel take to reach service in Virginia?

The schedule is set mainly by material delivery, design approval and the shop queue, with the Virginia steps added at the end: data report filing with the chief inspector and the first certificate inspection that issues the VA number. Paul Industries plans those last steps from the purchase order onward, so the filing goes in as soon as the data report is signed and the inspection is booked for the week the vessel is set.

What does a rerate cost compared with a new vessel?

A rerate costs calculations, a thickness survey, any reinforcing or nozzle work, a pressure test if the inspector requires one, and the R-2 filing, against the full cost of a new vessel plus removal and re-piping. Where the shell has enough thickness the rerate is usually far cheaper. Where it needs heavy reinforcement or the vessel is near the end of its corrosion allowance, Paul Industries prices the replacement beside it so the owner can compare.

Who pays for the first certificate inspection on a new Virginia vessel?

The certificate belongs to the owner or user, and DOLI issues it once the $20 certificate charge is paid and a satisfactory inspection report is received. The inspection itself is carried out by the owner’s insurance carrier or a contract fee inspector authorized by DOLI. Paul Industries can include booking that first inspection, preparing the vessel and presenting the data report in its installation scope, so the owner receives the certificate and VA number without separate arrangements.

Can a jacket be added to an existing pressure vessel in Virginia?

Adding a jacket is an alteration under the National Board Inspection Code, because it creates a new pressure chamber and changes the loads on the shell. It needs calculations for both chambers, including vacuum on the inner shell, a qualified welding procedure, examination, a pressure test of the jacket and an R-2 Report of Alteration filed with the chief inspector. Paul Industries designs, welds and tests the jacket and hands over the completed form.

What paperwork should a Virginia plant keep for each pressure vessel?

Keep the registered data report, the drawings and calculations, material test reports, the hydrostatic test record, the current inspection certificate posted at the vessel and every R-1 or R-2 filed since it entered service. Add the VA number to the plant’s equipment list. Paul Industries hands all of these over at completion as one turnover package, which makes later rerates, inspections and process safety reviews faster.

Are pressure vessels at a data center regulated in Virginia?

Data centers in Northern Virginia use air receivers, expansion tanks, chemical feed and filtration vessels on their cooling and fire systems, and any of these above the section 40.1-51.8 limits is regulated like a vessel in any other building. Water vessels with an air cushion within the Act’s 300 psi, 210 F and 120-gallon limits are exempt, so the vessel list for a data hall needs checking item by item.

Need a pressure vessel built or rerated in Virginia?

Send the data sheet or a sketch with contents, pressure, temperature, volume, material and nozzle list, plus the VA number for any vessel being replaced. Call 201-450-8280 or request a quote.