Paul Industries designs, fabricates, installs and tests process piping in Maine for pulp and paper mills, potato and seafood processors, breweries, diagnostics manufacturers and research campuses, from York County to Aroostook County. The work covers liquor and chemical lines at mills, product and refrigeration piping at food plants, purified water and clean utilities at life sciences sites, and the steam, condensate and compressed air that every plant runs on, built to ASME B31.3 or B31.1 and turned over with weld maps, examination reports and pressure test records. Paul Industries, headquartered at 256 Shore Drive, Kilmarnock, Virginia, offers supply-only spools, design-build packages and complete installation for Maine plants.

Request a quote or call 201-450-8280

Headquarters 256 Shore Drive, Kilmarnock, Virginia
Plumbing law Piping used exclusively for manufacturing or industrial processes is excluded (30-A M.R.S. 4201)
Fuel gas piping Fuel Board license required for gas and oil burning equipment work (32 M.R.S. 18102)
Building code MUBEC enforced in municipalities of more than 4,000 residents (10 M.R.S. 9724)
Public work Fair minimum wage on state-funded projects of $50,000 or more (26 M.R.S. 1304)
Reviewed November 2026

What does process piping in Maine carry?

Process piping in Maine carries a wider spread of fluids than the size of the state suggests: white and black liquor, chlorine dioxide and hot caustic at kraft pulp mills; potato slurry, frying oil, starch water and ammonia at Aroostook County processors; brine, seawater and wash water at coastal seafood plants; wort, beer, glycol and carbon dioxide in Greater Portland breweries; and purified water, clean steam and nitrogen at the diagnostics and laboratory buildings around Westbrook, Scarborough and Bar Harbor. Every one of those lines needs a code, a fluid service category, a material and a test chosen for its own conditions.

The general codes, materials and methods are set out on the national process piping page. This page works through what is particular to industrial piping Maine plants run: how the state’s plumbing law draws a line around process pipe, where fuel gas piping falls under the Maine Fuel Board, which building code reaches the room the pipe runs through, how air licenses and public funding change a schedule, and how a northern winter shapes testing and turnover.

What is industrial process piping, in Maine’s legal terms?

Industrial process piping is the pipe, valves and fittings that carry raw materials, intermediates, products, chemicals and utilities between the equipment of a manufacturing or industrial process. Maine writes that boundary into statute. The plumbing definition in 30-A M.R.S. section 4201 covers pipes, fixtures and apparatus that bring in potable water, remove wastewater and connect heating systems using water, and it excludes all piping, equipment or material used exclusively for manufacturing or industrial processes, except the initial connection to a potable water supply and the final connection that discharges indirectly into a public sewer or wastewater disposal system.

That exclusion is what separates a process line from plumbing in Maine. A reactor feed, a liquor header, a brewhouse transfer line or a purified water loop sits outside the plumbing definition because it serves the process alone. The domestic water branch that feeds the plant and the drain that leaves it sit inside, at the two connection points the statute names.

Process piping vs plumbing: where Maine’s plumbing law stops

Process piping vs plumbing in Maine comes down to use and to the two connection points. Under 32 M.R.S. section 3302 a license from the Plumbers’ Examining Board is required for anyone engaged in plumbing, and the same section ties that license to the permit requirement: no license is needed for an activity that needs no plumbing permit under 30-A M.R.S. section 4215, which requires a permit for the installation of plumbing into a building. The municipal plumbing inspector issues those permits and, by statute, issues none unless the applicant complies with the plumbing chapter.

On a plant project the split is drawn early, on the drawings. The backflow assembly and potable branch that supply a process skid, the hand sinks and safety showers in the process area, and the indirect waste receptor where process drains discharge are plumbing work with a permit. The process lines downstream of the backflow device, and the pretreatment piping upstream of the indirect connection, follow ASME B31.3 and the owner’s specification. Paul Industries marks both points on the isometrics and the plumbing riser so the permit, the inspection and the process records each cover their own pipe.

Where common Maine plant lines fall: process piping or plumbing
LineTypical Maine settingClassificationWhat follows from it
White liquor, black liquor and chemical feedKraft pulp millsProcess piping, excluded from the plumbing definitionB31.3 design, examination and test; owner’s mill specification
Potato slurry, starch water and fryer oilAroostook County processorsProcess pipingB31.3 or sanitary specification; cleanability and drainage built in
Domestic cold water supply to a process skidEvery plantPlumbing up to the initial connectionPlumbing permit and inspection; process piping begins downstream
Process drains to an indirect waste receptorFood, seafood and brewery floorsProcess piping up to the final indirect connectionReceptor and building drain under the plumbing permit
Natural gas or propane to a fryer, dryer or boiler burnerFood plants, mills, breweriesFuel gas piping under the Maine Fuel BoardNFPA 54 or NFPA 58 as adopted by Board rule
Steam from a power boiler to its stop valvesMills and large plantsBoiler external pipingASME Section I jurisdiction, built to B31.1, tied to the boiler inspection
Fire sprinkler mains and standpipesAll occupied buildingsExcluded from plumbing; fire protection workFire protection design and acceptance testing

Fuel gas lines to burners, dryers and fryers

Fuel gas piping to process equipment in Maine falls under the Maine Fuel Board, created under 32 M.R.S. Chapter 139. Section 18102 requires a person who installs or services oil, propane or natural gas burning equipment to hold a license under that chapter, and the Board’s Chapter 6 rule adopts NFPA 54, the National Fuel Gas Code, and NFPA 58, the Liquefied Petroleum Gas Code, with Maine exclusions and amendments. Gas trains on fryers, dryers, ovens, direct-fired air heaters and boiler burners are therefore built and tested to those standards, with the Board’s rules applied before the equipment is put into service.

Many Maine plants outside the areas served by natural gas mains run on delivered propane, from rural food processors to sugarhouses. A plant switching a dryer from propane to pipeline gas, or adding a vaporizer for a large propane load, changes pipe sizing, regulator stations and venting, and that work belongs in the same package as the process piping it serves. Burner and boiler work is covered on the boiler repair in Maine page.

Industrial plants in Maine and the piping they run

Industrial plants in Maine cluster in five settings: the mill towns along the Androscoggin, Kennebec, Penobscot and St. Croix rivers; potato country in Aroostook County; the coastal fishing ports from Portland to Washington County; Greater Portland’s mix of breweries, diagnostics manufacturers and food plants; and the research and shipbuilding centers of the midcoast and Downeast. The table below shows what each setting tends to put through its pipe and what shapes the job.

Maine plant settings and the process piping they generate
SettingPlant typesTypical linesWhat shapes the job
River mill towns: Rumford, Jay, Skowhegan, Baileyville, MadawaskaPulp and paper, biomass powerLiquor, chemical feed, stock, white water, steam, condensateAnnual outages, caustic and oxidizing chemicals, large bore pipe
Aroostook County and Presque IslePotato processing, starch, storageSlurry, wash water, fryer oil, ammonia, wastewaterHarvest-season peaks, deep cold, long freight distances for spools
Portland, South Portland and WestbrookBreweries, diagnostics, food, terminalsWort, beer, glycol, CO2, purified water, nitrogenOccupied buildings, tight urban sites, frequent expansions
Lewiston-Auburn, Augusta and WatervilleFood, textiles, light manufacturing, hospitalsSteam, hot water, compressed air, process waterOlder brick mill buildings converted to new uses
Midcoast, Downeast and Washington CountySeafood, aquaculture, marine ingredients, researchSeawater, brine, wash water, refrigeration, lab utilitiesSalt air corrosion, seasonal landings, remote sites
Brunswick, Bath and KitteryShipbuilding, defense, redeveloped basesCompressed air, steam, cooling water, hydraulic oilLarge industrial buildings, security and access controls

Liquor, bleach chemicals and caustic at Maine pulp mills

Kraft pulp mills give Maine its most demanding process lines. White liquor, a hot solution of sodium hydroxide and sodium sulfide, cooks wood chips in the digester; the spent black liquor goes through evaporators to the recovery boiler, where the chemicals are recovered and the organics burned for steam. Chlorine dioxide used in bleaching is strongly oxidizing and is commonly piped in fiberglass-reinforced plastic or titanium, while caustic and liquor lines run in carbon or stainless steel chosen against the mill’s temperature and concentration limits. Mill piping is replaced during planned outages, so spools are fabricated and tested ahead of the shutdown and staged by sequence. Related vessel and tank work is covered on the pressure vessel fabrication in Maine and tank fabrication in Maine pages.

Potato processing in Aroostook County

Aroostook County is where Maine’s potato crop is grown and much of it is processed. McCain Foods has run the Easton plant since 1976, is the largest buyer of potatoes in the county, and processes roughly a third of the county’s crop there; in November 2025 it agreed to buy Penobscot McCrum, whose plant is in Washburn. Frozen potato plants of that kind run water flumes, peelers, blanchers, fryers, freezers and starch recovery, which means stainless product and water piping, oil piping held at frying temperature, ammonia refrigeration to IIAR 2, and wastewater lines carrying heavy solids. Plants of that kind are named here as a description of the market. Processing peaks after the harvest, so for process piping, Maine potato plants plan their changes for the summer months before the crop arrives.

Seafood, breweries and life sciences on the southern coast

Seafood plants from Portland to the Downeast ports run seawater intakes, brine chillers, cookers and wash-down systems in a salt atmosphere that attacks carbon steel and unprotected fasteners. Greater Portland breweries add hot liquor, wort, glycol and carbon dioxide piping as cellars expand. Diagnostics and research buildings need purified water, clean steam and sanitary piping that stands up to an audit. The sanitary side of that work is set out on the sanitary process piping in Maine page, and food plant work in general under food and beverage.

Industrial piping, Maine codes and the state rules around the job

ASME B31.3 Process Piping governs most process lines in Maine plants, ASME B31.1 governs boiler external piping and power plant steam, and five state rule sets sit around the work: the plumbing law, the Fuel Board rules, the boiler and pressure vessel law, the Maine Uniform Building and Energy Code, and Department of Environmental Protection air licensing. The owner, usually through its engineer of record, assigns the code and fluid service category to each line; the state rules decide which permits, inspections and records go with the job.

State rules that can sit around a process piping job in Maine
RuleAdministered byWhat it reachesEffect on the piping job
30-A M.R.S. 4201 and 4215; 32 M.R.S. Chapter 49Plumbers’ Examining Board and municipal plumbing inspectorsPotable water, wastewater and heating connectionsPermit for the initial and final connections; process lines excluded
32 M.R.S. Chapter 139; 02-658 CMR Chapter 6Maine Fuel BoardOil, propane and natural gas burning equipmentFuel gas trains built and tested to NFPA 54 or NFPA 58
32 M.R.S. Chapter 131Office of Professional and Occupational Regulation, Boiler and Pressure Vessel Safety ProgramBoilers and pressure vessels above the statutory exemptionsBoiler external piping and vessel connections tied to state inspection
10 M.R.S. 9724, MUBECMunicipal code officers where enforcedBuildings constructed or renovatedBuilding permit for structure, supports and building systems
06-096 CMR Chapter 115Maine DEP Bureau of Air QualityNew and modified emission sourcesLicense in place before construction on a new emission point begins
29 CFR 1910.119Federal OSHA, Augusta Area Office and BangorProcesses above threshold quantities of listed chemicalsManagement of change and pre-startup safety review

Steam lines and the Maine boiler law

Maine’s boiler and pressure vessel law, 32 M.R.S. Chapter 131, adopts the ASME Boiler and Pressure Vessel Code as its standard and reaches power boilers and pressure vessels above the exemptions in section 15102. Vessels operating at 15 psi or less are exempt, as are small vessels such as those of 6 inches inside diameter or less. For piping that means boiler external piping, from the boiler to its stop valves, falls under Section I jurisdiction and is built to B31.1, while process steam and condensate downstream follow the code the owner assigns. A new receiver, separator or blowdown tank tied into the piping may be a state-inspected vessel, so its data report and certificate are checked before tie-in.

MUBEC in the building around the pipe

The Maine Uniform Building and Energy Code must be enforced in every municipality with more than 4,000 residents under 10 M.R.S. section 9724, and smaller towns that choose to enforce a code must use MUBEC rather than any other. Process piping inside an industrial building answers to B31.3 and the owner’s engineering, but supports anchored to the structure, new pipe racks, roof penetrations and mezzanines touch the building code, so a plant in Portland, Bangor or Lewiston sees a code officer on those items, and in a smaller town the owner confirms whether the town has chosen to enforce MUBEC.

Air licenses and new emission points

A Maine DEP air emission license under Chapter 115 must be in place before construction of a new or modified emission source begins, and the Department’s 2024 guidance tells owners that a new source review license is generally needed before equipment is even ordered. Piping rarely emits by itself, but a new vent header, a dryer exhaust, a fuel line to a larger burner or a tank vent can change what a unit releases. Paul Industries schedules fabrication and field work around the license status the owner confirms, so pipe that sits outside the change covered by the license keeps moving while the license is pending.

Pipe fabrication: Maine spools, modules and freight

Pipe fabrication for Maine plants moves welding, examination and hydrotesting off site, so a mill or food plant sees bolt-up and final welds instead of weeks of hot work inside its fence. Paul Industries cuts, fits, welds, examines and tests spools under controlled conditions, labels them to the isometrics and ships them in the order the field team will set them. For pipe fabrication Maine projects need in Aroostook County or Washington County, spool sizes are set with the freight route in mind, and the spring road postings that limit truck weights on many Maine roads after the thaw are part of the delivery plan. Rack modules with steel, pipe, cable tray and insulation fitted together suit mill outages, where a few days of access have to carry a large scope.

How does a Maine winter change testing and tie-ins?

A Maine winter changes testing because water left in a pipe freezes and splits it, and much of the state spends long stretches well below freezing. The National Weather Service counts about eight nights below zero in an average January at Bangor and about fifteen at Caribou. A hydrostatic test at 1.5 times design pressure is the B31.3 default, so Paul Industries heats test water, isolates outdoor runs, drains low points and blows lines dry promptly after the hold. Where water would harm the service, as in fryer oil, refrigerant or instrument air, a pneumatic test at 1.1 times design pressure runs under a written plan with exclusion zones and staged pressure holds.

Tie-ins at a running Maine plant are made during a planned outage, with isolation, draining and purging under the plant’s procedures, or hot, by welding a fitting onto a pressurized line and cutting into it with a hot tap machine. Mills plan their large tie-ins for the annual outage; potato processors plan theirs for the gap before harvest; breweries and food plants use weekend or changeover windows. At plants covered by process safety management, the change runs through management of change before work and a pre-startup safety review before chemicals are introduced. Maine’s OSHA state plan covers public employers, so federal OSHA enforces those rules at private plants through its Augusta Area Office and Bangor office. Weld procedure and welder records for that work are covered on the industrial welding services in Maine page.

How often should pipes be inspected at a Maine plant?

Pipes at a Maine plant should be inspected on intervals set by fluid service, corrosion rate and consequence, rather than on one calendar for the whole site. API 570 sets the framework many owners follow for in-service process piping: external visual inspection and thickness measurement at condition monitoring locations, with intervals tightened for lines in severe or toxic service and relaxed for benign utilities. Caustic and liquor lines at mills, seawater and brine lines on the coast, and buried or insulated lines where water can collect under jacketing in freeze and thaw cycles deserve the shortest intervals. Paul Industries replaces the sections that inspection condemns, records new baseline thicknesses and updates the line list so the next inspection starts from accurate data.

How much does process piping in Maine cost?

Process piping in Maine is priced on fluid service, material, pipe size, weld count, examination level, access and outage constraints more than on footage. A titanium chlorine dioxide line with full examination at a mill costs far more per foot than a compressed air header of the same size, and a tie-in made in a two-day mill outage costs more than the same welds made in a fabrication bay. Distance to the site and winter conditions affect freight, heating and enclosure costs, and fuel gas work adds the testing and documentation the Fuel Board rules require.

Public money adds a defined cost item. Maine’s fair minimum wage law, 26 M.R.S. sections 1304 to 1306, applies to public works funded in whole or in part by state funds where the contract amounts to $50,000 or more, at wage and benefit rates set by the Director of the Bureau of Labor Standards. Paul Industries prices from a line list or P&IDs, gives a budget range from comparable scope early, and fixes the price once the specification, tie-in points and outage dates are defined.

Who installs process piping in Maine?

Paul Industries installs process piping in Maine, carrying each job from design and material procurement through fabrication, installation, examination, testing and turnover under one contract. The company is headquartered at 256 Shore Drive in Kilmarnock, Virginia, was formerly based in northern New Jersey, then Pennsylvania, and builds plant piping throughout Maine, across all 50 states and at plants outside the United States. Owners with sites in several states find the same approach on the process piping in Virginia page for the headquarters state, on the process piping in Massachusetts page, and across the region on the New England page.

Among the mechanical contractors in Maine and the piping contractors Maine owners compare, the useful test is the record set handed over at the end: weld maps tied to welder identities, procedure qualifications under ASME Section IX, examination reports, material certificates, pressure test records and the plumbing, fuel gas and boiler paperwork each connection needs. Paul Industries hands that set over for every line, and qualification of finished systems for regulated plants is covered on the validation and commissioning in Maine page.

Process piping from Paul Industries across Maine

Paul Industries designs, fabricates, supplies, installs, tests, starts up, services and repairs process piping in Maine for pulp and paper mills, potato and seafood processors, breweries, diagnostics and research buildings and shipyard support facilities, from Kittery and Portland to Bangor, the river mill towns and Aroostook County. More on the state sits on the Maine page. Send a line list, the piping specification and your outage dates, call 201-450-8280 or request a quote.

Standards referenced: ASME B31.3 Process Piping · ASME B31.1 Power Piping · ASME Boiler and Pressure Vessel Code Section I and Section IX · NFPA 54 National Fuel Gas Code · NFPA 58 Liquefied Petroleum Gas Code · IIAR 2 · API 570 · OSHA 29 CFR 1910.119 process safety management · 30-A M.R.S. 4201 and 4215 (Maine plumbing definition and permits) · 32 M.R.S. Chapter 49 (Plumbers' Examining Board) · 32 M.R.S. Chapter 139 and 02-658 CMR Chapter 6 (Maine Fuel Board) · 32 M.R.S. Chapter 131 (Maine boilers and pressure vessels) · 10 M.R.S. 9724 (Maine Uniform Building and Energy Code) · 06-096 CMR Chapter 115 (Maine DEP air emission licenses) · 26 M.R.S. 1304 to 1306 (fair minimum wage on public works)

Frequently asked questions

Who installs process piping at potato plants in Aroostook County and Presque Isle?

Paul Industries installs product, water, fryer oil, ammonia and wastewater piping at potato processors across Aroostook County, from Presque Isle and Caribou to Easton and Washburn. Work is planned for the months before harvest, spools are fabricated and tested ahead of delivery with the freight route in mind, and stainless product lines are built to drain fully so wash-down and sanitation hold up through the processing season.

Does Paul Industries take mill piping work in Rumford, Jay, Skowhegan and the western mountains?

Yes. Paul Industries builds liquor, chemical feed, stock, steam and condensate piping at pulp, paper and biomass plants in the river mill towns, including Rumford and the western mountains, Jay, Skowhegan and the Kennebec Valley. Outage scopes are fabricated in advance, sequenced to the mill’s shutdown plan and tested before the outage window opens, so the mill restarts on schedule with a complete record set.

Which mechanical contractors in Portland, Maine handle brewery and lab piping?

Paul Industries is among the mechanical contractors Portland, Maine breweries, diagnostics makers and laboratory buildings bring piping work to, including South Portland and Westbrook. Brewery work covers hot liquor, wort, beer, glycol and carbon dioxide lines; laboratory and diagnostics work covers purified water, clean steam, nitrogen and process drains, built inside occupied buildings with dust, noise and hot work controlled to the owner’s rules.

Do mechanical contractors in Bangor, Maine take on plant piping for hospitals and food processors?

Paul Industries takes the piping work that mechanical contractors Bangor, Maine owners call on for: steam and condensate in hospital plants, process and refrigeration lines at food processors, and compressed air and water systems in manufacturing buildings across the Penobscot region. Projects in occupied hospitals are phased around patient care areas, with isolation and restoration of each system planned before the first valve is closed.

What should a plant compare when choosing among mechanical contractors Maine offers for process piping?

Compare the record set and the scope under one contract. Ask for sample weld maps, procedure and welder qualification records, examination reports and test packages from a comparable job, and check that design, fabrication, installation, testing and turnover sit with one firm. Paul Industries provides all of that for process piping in Maine, from a single spool to a complete plant expansion, with one schedule and one point of contact.

Who are the piping contractors Maine seafood plants Downeast and Bar Harbor research buildings call on?

Paul Industries builds seawater, brine, wash water and refrigeration piping for seafood plants Downeast and in Washington County, and laboratory utilities for research buildings around Bar Harbor and Ellsworth. Coastal lines are specified for salt air and seawater, with stainless grades, nonmetallic pipe or coatings chosen for each service, and supports and fasteners selected so the installation holds up season after season in salt air.

What is a piping contractor, and what should one hand a Maine plant at the end of a job?

A piping contractor designs, fabricates, installs and tests the pipe, valves, fittings and supports that carry a plant’s fluids, and answers for the code compliance of every weld and joint. At turnover a Maine plant should receive as-built isometrics, the line list, material certificates, weld procedure and welder qualification records, examination reports and pressure test records, plus any plumbing, fuel gas or boiler paperwork the connections required.

What do Maine plumbing license requirements mean for process piping inside a plant?

Maine plumbing license requirements follow the plumbing definition in 30-A M.R.S. section 4201, which excludes piping used exclusively for manufacturing or industrial processes. The Plumbers’ Examining Board license and the municipal plumbing permit therefore apply to the potable water supply connection, fixtures, safety showers and the final indirect waste connection, while the process lines between those points follow B31.3 and the plant’s own specification.

Is a domestic water line feeding a CIP skid plumbing or process piping in Maine?

The supply up to and including the initial connection to the potable water system is plumbing under the statute, with a permit and the backflow protection the plumbing code requires. Downstream of that connection, the CIP supply and return piping serves the process alone, so it is designed and tested as process piping. Paul Industries draws that break at the backflow assembly on the drawings.

Does fuel gas piping to a fryer or dryer fall under the Maine Fuel Board?

Yes. Under 32 M.R.S. section 18102, installing or servicing oil, propane or natural gas burning equipment requires a license under the Fuel Board chapter, and the Board’s Chapter 6 rule adopts NFPA 54 and NFPA 58 with Maine amendments. Gas trains, regulators, vents and the piping that feeds them are sized, installed and tested to those standards before the burner is fired.

Does a steam separator or blowdown tank added to a piping job need a Maine pressure vessel certificate?

It depends on size and pressure. Maine’s boiler law covers pressure vessels above the exemptions in 32 M.R.S. section 15102, which excludes, among others, vessels operating at 15 psi or less and vessels of 6 inches inside diameter or less. A larger vessel in steam service carries an ASME data report and is registered for state inspection before it goes into service, so its paperwork is checked before tie-in.

Does a piping change at a Maine plant need a DEP air emission license amendment?

A piping change needs a license or amendment under Chapter 115 when it is part of a new or modified emission source, such as a larger burner, a new dryer exhaust or a new process vent. The license must be in place before construction on that source begins. Paul Industries supplies the equipment and piping details the owner’s permit engineer needs and sequences the related field work to the license.

Do state-funded piping projects in Maine pay the fair minimum wage?

Yes, when the project is a public work funded in whole or in part by state funds and the contract is $50,000 or more, under 26 M.R.S. section 1304. The public authority obtains the fair minimum wage and benefit rates from the Director of the Bureau of Labor Standards before bidding, and Paul Industries prices the labor to the rates in the bid documents.

How are outdoor process lines hydrotested in a Maine January?

Outdoor lines are tested with heated water inside temporary enclosures where needed, with low points drained and lines blown dry with air or nitrogen as soon as the hold is complete. Where water would harm the service, a pneumatic test at 1.1 times design pressure is run under a written safety plan. Heat tracing and insulation are completed and checked before the line is left full.

What materials suit chlorine dioxide, caustic and liquor piping at a Maine mill?

Chlorine dioxide solution is strongly oxidizing and is commonly carried in fiberglass-reinforced plastic or titanium. White liquor and caustic run in carbon steel within the mill’s temperature and concentration limits, or in stainless steel above them, and black liquor lines are chosen against temperature and solids. Paul Industries works to the mill’s piping specification and flags any line whose service has changed since it was written.

How is ammonia refrigeration piping handled at a Maine food plant?

Ammonia refrigeration piping is designed and installed to IIAR 2, with carbon steel or stainless pipe, relief piping routed to a safe discharge, and labels and valve tags that match the system diagrams. Systems above the federal threshold quantity are covered by process safety management, so the change runs through management of change and a pre-startup review before the system is charged.

Which delivery routes does Paul Industries offer for process piping in Maine?

Paul Industries offers supply-only fabricated spools and rack modules, examined, tested and labeled to the isometrics; design-build packages that start from a process description and finish with issued drawings and a tested system; and complete installation from survey through turnover. Many Maine mills use spools for outage work and complete installation for expansions and new lines.

How does Paul Industries plan piping deliveries during Maine's spring road postings?

Many Maine roads are posted with reduced weight limits during the spring thaw, so deliveries to sites on posted roads are timed before or after the posting period, split into lighter loads, or routed over unposted highways. Spool and module sizes are set at design stage with that in mind, so the fabrication schedule and the delivery schedule match.

What should a Maine plant send to get process piping priced?

Send P&IDs or a line list, the piping specification and fluid service categories, tie-in locations with photos, outage or harvest-season dates, site rules for hot work and access, and whether state funds, an air license or fuel gas work are involved. Paul Industries returns a budget range first and a firm price once the scope is fixed.

Adding or replacing process lines at a Maine plant?

Send a line list or P&IDs, the piping specification, tie-in locations and your outage or harvest dates. Call 201-450-8280 or request a quote.