Paul Industries provides tank fabrication in Vermont, designing, building and installing fuel storage tanks, stainless process tanks for dairy, brewing and food plants, and water and thermal storage tanks for hospitals, campuses and manufacturers. Vermont splits tank rules by contents and location: the Agency of Natural Resources regulates petroleum tanks above and below ground, and the Division of Fire Safety brings in NFPA 30, NFPA 31 and the building code’s snow loads. Paul Industries builds each tank to the rule that governs it and to the winter it will stand through.

Request a quote or call 201-450-8280

Headquarters 256 Shore Drive, Kilmarnock, Virginia
AST Rules ANR, effective August 1, 2024
UST Rules ANR, effective October 26, 2020
AST inspection By the fuel carrier, every 4 years at least
Existing AST upgrades Due by July 1, 2030
Roof snow load 40 psf minimum on low-slope roofs (2025 code)
Reviewed November 2026

What does tank fabrication in Vermont have to satisfy?

Tank fabrication in Vermont has to satisfy a construction standard chosen for the tank’s contents and pressure, and then the state program that covers its use. A steel tank for diesel or heating oil is built to a listing standard such as UL 142 above ground or UL 58 below ground and installed under the Agency of Natural Resources rules. A stainless tank for milk, ice cream mix, wort or maple syrup is built to sanitary design practice such as the 3-A Sanitary Standards and installed under the building and fire codes. A large field-erected storage tank follows API 650, or API 620 when it holds a small internal pressure, and a welded steel water tank follows AWWA D100.

Pressure draws the outer line. Section 7 of the 2025 Vermont Fire and Building Safety Code defines an unfired pressure vessel as a container with pressure from an external source above 15 psi, so a tank designed for more than that is a pressure vessel and goes through the commissioned inspection described on pressure vessel fabrication in Vermont. Every tank on this page sits at atmospheric pressure or close to it.

Which Vermont rules govern a tank, by contents and location
TankGoverning programTypical construction standardKey Vermont requirement
Aboveground heating oil, diesel, kerosene, gasoline or used oilANR Aboveground Storage Tank Rules, 2024UL 142 or NFPA 31 design for small tanks; API 650 for large field tanksConcrete pad, overfill alarm, metallic fill and vent, carrier inspections
Underground motor fuel or chemical tankANR Underground Storage Tank Rules, 2020, category oneUL 58 with STI-P3 or UL 1746; UL 1316 fiberglass; STI F841 double wallConstruction and operating permits, secondary containment
Underground heating oil tank over 1,100 gallons or at a public buildingANR UST Rules, category threeSame listing standardsRegistration with the Agency
Aboveground Class I fuel dispensing tankFire code, NFPA 30A as amendedFire resistant tank under NFPA 30A 4.3.4Separation distances from the NFPA 30A table
Stainless dairy, brewing or food tankBuilding and fire codes; food safety programs3-A Sanitary Standards, ASME BPE practiceSnow, wind and seismic design for outdoor silos
Fire protection or process water tankFire code, NFPA 22AWWA D100 welded steel; AWWA D120 or polyethylene for 13R systemsFoundation, freeze protection, outlet and vent design

What do the Vermont aboveground storage tank regulations require of a new tank?

The Vermont aboveground storage tank regulations require a new petroleum tank to use one of five approved designs, stand on a sized concrete pad, carry an overfill alarm, use metallic fill and vent piping and be inspected by the fuel carrier at set points in its life. The Agency of Natural Resources adopted the current Vermont AST Rules under 10 V.S.A. 1929a, effective August 1, 2024, replacing the 2017 rules. They cover tank systems storing gasoline, diesel, kerosene, used oil or heating oil, which takes in boiler fuel oil, generator diesel and fleet fuel at plants and institutions. Mobile and semi-mobile skid tanks are left out of the definition.

The approved designs for a new tank are a single-wall tank of at least 12-gauge steel throughout, built to section 7.2.7 of NFPA 31; a double-bottom steel tank with end-cover protection and interstitial monitoring; a double-wall tank with a plastic inner wall and a metallic outer wall; a double-wall non-metallic tank; or a single-wall non-metallic tank for indoor use. Installation follows NFPA 1, NFPA 30 and 31, or another method the Secretary approves in writing.

Foundation, fill, vent and valve details in the Vermont AST Rules

The Vermont above ground storage tank rules spell out installation details that go into the fabrication drawings. A new tank sits on a single continuous concrete pad, or bolted concrete slabs, at least 4 inches deep and 10 percent longer and wider than the tank. A tank that receives pressurized deliveries carries an overfill vent alarm or whistle, with the vent ending no more than 12 feet from the fill and visible from it. A new bottom-fed tank has a shutoff valve within 12 inches of the outlet. New tanks carry a fuel gauge and legs no longer than 14 inches, and tanks installed since August 15, 2017 carry a permanent tag showing the installation date.

Storage tank venting requirements in Vermont follow the NFPA minimum vent diameters, and fill and vent pipes are at least 1 1/4 inches inside diameter, made of metal, ending outside the building, with a liquid-tight fill cap and a weatherproof, insect-proof vent cap. PVC and other non-metallic fill and vent pipe is prohibited. Fill and vent piping on new tanks follows NFPA 31, with threaded ends or press-connect fittings listed to UL 180, and a system with several tanks gives each tank its own fill, gauge, vent and alarm. Buried fuel lines are coated and run in a continuous non-corroding sleeve, with no fittings underground.

Vermont AST Rules requirements and what the fabricated tank delivers
RequirementRuleHow the tank and installation meet it
Tank designOne of five designs; steel single-wall at least 12-gauge per NFPA 31Design and gauge selected for contents, location and indoor or outdoor service
FoundationConcrete pad at least 4 in deep, 10 percent larger than the tankPad drawn with the tank; anchors cast in where flood rules apply
OverfillVent alarm or whistle; vent within 12 ft of the fill and visible from itVent and fill located together on the tank layout
Fill and ventAt least 1 1/4 in, metallic, PVC prohibited; NFPA 31 pipingSteel fill and vent with threaded or UL 180 press-connect ends
Shutoff and gaugeValve within 12 in of a bottom outlet; gauge on new tanksValve and gauge fitted before delivery
Snow and iceGable end or away from the building, containment, or a roofed shelterLocation and shelter shown on the site plan
Legs and date tagLegs no longer than 14 in; installation date tagSaddles or short legs; permanent tag applied at installation

Existing fuel tanks and the July 1, 2030 deadline

Existing fuel tanks in Vermont face a firm upgrade date: by July 1, 2030, every aboveground system covered by the 2024 rules must meet the new foundation, fill and vent pipe, buried line, leg length and outdoor snow and ice protection requirements, and tanks in flood prone areas and at marinas must meet their added rules. Older generator and heating oil tanks set on gravel, standing on long legs or vented with plastic pipe get upgraded or replaced before that date.

Replacement can cost less than rework once the pad, legs, fill and vent all need changes. Paul Industries surveys existing tanks against the 2030 list, prices upgrade and replacement side by side, and fabricates and installs new tanks that meet the rules from the first delivery. Vermont oil tank regulations also tie in to the fuel supply: the carrier inspects a new tank after installation and before the first delivery, again right after the first delivery, before the first delivery whenever the owner changes carriers, and at least every four years, an interval the 2024 rules extended from three years.

Fuel tanks in Vermont flood hazard areas

Fuel tanks in Vermont flood hazard areas, as 10 V.S.A. 752 defines them, need protection against floating and releases on top of the standard installation rules. A new tank inside a building gets a vent pipe long enough to rise above the projected flood level, and the tank is anchored to its pad by foot flanges bolted to the slab, concrete anchors cast in with hold-down straps, earth augers under an undersized pad with straps, or another method the tank maker or installer recommends. Straps carry turnbuckles and sit over the anchor points without blocking openings. New outdoor tanks in a flood hazard area meet the same anchoring and vent rules unless the Secretary grants an exemption.

Sites along the Winooski, Lamoille, Otter Creek and Connecticut River valleys start with the flood maps before setting any fuel tank. Paul Industries designs the anchoring with the tank and pad, sizes straps and anchors for buoyancy at the flood depth, and routes the vent to clear the projected flood level.

Vermont underground storage tank regulations for buried tanks

Vermont underground storage tank regulations sort buried tanks into three categories, and the category decides the paperwork. The Vermont UST Rules, in effect since October 26, 2020 under a program that began in 1985, cover tanks holding liquid petroleum or hazardous substances; propane is excluded. Category one is any underground tank of any size except heating oil tanks used for on-premises heat and farm or residential motor fuel tanks. Category two covers farm or residential motor fuel tanks over 1,100 gallons. Category three covers heating oil tanks over 1,100 gallons, or any heating oil tank at a public building.

A category one system needs a construction permit from the Secretary before construction, installation or replacement begins, valid for up to one year, and an operating permit valid for up to five years, displayed at the facility, with the fee paid every year. Categories two and three go through Vermont underground storage tank registration instead. The Vermont underground storage tank program also requires 30 days’ notice before a tank switches to fuel with more than 10 percent ethanol or 20 percent biodiesel, with every component shown to be compatible.

Construction and containment under the Vermont underground storage tank rules

The Vermont underground storage tank rules set construction standards in line with national underground fuel tank regulations. A new steel tank meets UL 58 or its Canadian equivalent and a corrosion protection standard such as STI-P3 or UL 1746; a fiberglass tank meets UL 1316; a composite tank meets UL 58 with UL 1746 or the STI ACT-100 specifications. Every new category one and category two tank carries secondary containment, and a double-walled tank must be designed so a leak through the inner wall is readily detected, with steel outer walls built to STI F841. Installation and substantial alteration follow PEI RP100, 2017 edition.

Many owners now replace buried tanks with aboveground tanks they can see and inspect. Paul Industries prices both routes, removes the old tank, and supplies and installs the replacement under the rule that will govern it.

Fire code rules for fuel, propane and water storage tanks

The fire code adds its own rules on top of the Agency’s. The 2025 Vermont Fire and Building Safety Code requires no fire code permit for an underground tank the Agency regulates, but tanks at public buildings, aboveground flammable and combustible liquid tanks, and propane tanks larger than 2,000 gallons or installations over 4,000 gallons in aggregate need a Division of Fire Safety permit. Above ground fuel tank regulations in the 2021 edition of NFPA 30A, as Vermont amends it, require any aboveground tank storing Class I liquids such as gasoline for fuel dispensing to be a fire resistant tank, located by the NFPA 30A separation table, with other liquids allowed at half those distances.

Water tanks for fire protection follow NFPA 22, and Vermont’s amendment allows polyethylene tanks or tanks built to AWWA D120 as the water supply for NFPA 13R sprinkler systems. Paul Industries prepares the permit drawings for the Division and fabricates fire water tanks with the outlets, vents, heating and level instruments the sprinkler design needs.

Stainless process tanks for Vermont dairy, brewing and food plants

Stainless process tanks carry most of Vermont’s food production, from milk silos and cheese vats to brite tanks and syrup storage. Agri-Mark makes Cabot cheese at plants in Cabot and Middlebury, Ben & Jerry’s runs ice cream factories in St. Albans and Waterbury, and The Alchemist brews in Waterbury and at its Stowe brewery and visitor center. Plants of those kinds buy raw milk silos, balance and surge tanks, mix and blend tanks, culture and whey tanks, fermenters, brite tanks, hot liquor and cold liquor tanks, and clean-in-place supply and return tanks.

Sanitary tanks are built for cleaning as much as for holding product: crevice-free welds ground and polished to the specified finish, sloped bottoms that drain completely, spray devices sized to reach every wetted surface, sanitary outlets and manways, and passivation after fabrication. Paul Industries fabricates and installs those tanks, ties them into process piping in Vermont, and restores the passive layer on new or repaired stainless through passivation services in Vermont.

Designing outdoor tanks for Vermont snow, ice and cold

Outdoor tanks in Vermont are designed for snow loads that change from town to town and for months of freezing weather. The 2025 code sets ground snow loads from its map of Vermont towns and cities, with values above 2,500 feet of elevation approved by the authority having jurisdiction, and requires a minimum roof snow load of 40 pounds per square foot on building roofs sloped at 5 degrees or less. A tank roof, platform or shelter is checked against the site’s ground snow load with drifting from adjacent buildings, and a cone roof on a silo or storage tank is designed for that load along with wind and seismic forces.

Cold shapes the rest of the design. Fuel oil and biodiesel thicken in winter; water, wort and cleaning solutions freeze in exposed nozzles and lines; and frost lifts poorly drained pads. Paul Industries specifies insulation, heat tracing, heated enclosures and frost-protected foundations to match the contents and the site, and places outdoor fuel tanks where sliding snow and ice from a roof will miss them, which the AST Rules require.

Shop-built or field-erected tanks for Vermont sites

Shop-built and field-erected tanks split at the size a truck can carry on Vermont roads. With a legal width of 102 inches and a legal height of 13 feet 6 inches, larger diameters move under oversize permits on routes chosen for bridges, grades and turns, and a very tall or wide tank is fabricated in sections or erected on site. Field-erected tanks, built to API 650 or AWWA D100, rise on a prepared foundation with shell courses welded in place, then go through the standard’s examination and hydrostatic test before service.

Paul Industries chooses the route that fits the tank and the site: full shop fabrication for most process tanks and fuel tanks, shop-built shell sections with field closure welds where access is tight, and field erection for large storage. Field welding runs with industrial welding services in Vermont.

How often should storage tanks be inspected in Vermont?

Storage tanks in Vermont are inspected on schedules set by the program that covers them. A petroleum AST gets the fuel carrier’s inspection after installation, after the first delivery, when carriers change and every four years at least. A category one UST follows the operation and maintenance rules in the UST Rules, with release detection, periodic inspections and testing of spill and overfill equipment. Large field-erected storage tanks are commonly inspected under API 653, and food and water tanks follow the plant’s own sanitation and maintenance programs. Paul Industries repairs findings from any of these inspections and replaces tanks that have reached the end of their service.

Owners who manage sites in several states find that above ground storage tank regulations differ most in who inspects and how often. Vermont gives the routine aboveground inspection to the fuel carrier at each delivery milestone, and a failed inspection stops the fuel. The inspector fixes a red “Do Not Fill” tag to the tank and its fill port, and enters the result in the state’s tracking database within five business days. The 2024 rules added a conditional yellow tag for a short list of lesser defects, but only on tanks serving residential property, so a tank at a plant, school or hospital that fails is red tagged and receives no deliveries until it is corrected. Paul Industries treats a red tag as a repair order and returns the tank to compliance so deliveries resume.

Who inspects a Vermont tank, and on what schedule
Tank typeInspected byScheduleCommon repair findings
Aboveground petroleum tankThe fuel carrier, under the AST RulesAfter installation, after the first delivery, on a change of carrier, at least every four years, at removalPad settlement, missing alarm, plastic vents, unsleeved buried lines, long legs
Category one underground tankOwner and operator under the UST Rules, with Agency compliance inspectionsRelease detection, periodic inspections and spill and overfill equipment testing as the rules setSump leaks, failed spill buckets, overfill device faults, corrosion protection readings
Large field-erected storage tankAn API 653 inspector, by owner practiceExternal and internal intervals set from corrosion ratesBottom and shell thinning, roof and seal damage, settlement
Stainless process tankThe plant’s sanitation and maintenance programSet by the plant’s food safety plan and auditsWeld and finish defects, spray device coverage, gasket and vent wear
Fire protection water tankInspection under NFPA 25 as the fire code adopts itPeriodic visual and interior inspectionsCoating failure, heater faults, level and valve problems

What does tank fabrication cost in Vermont?

The cost of tank fabrication in Vermont depends on the tank’s volume, material, wall design, finish, nozzles and accessories, plus the foundation, shelter, anchoring and permits the site needs. A double-wall steel generator tank with alarms and a containment pad, a polished stainless brite tank, and a field-erected water tank sit in very different price ranges. Upgrading or replacing existing fuel tanks before the 2030 deadline, removing old buried tanks, and winter installation also move the total. Paul Industries prices from the tank’s data, the site plan and the governing rule, gives a budget range from comparable work, and confirms a firm price once the design is set.

Who fabricates tanks in Vermont?

Paul Industries fabricates tanks for Vermont plants, hospitals, campuses, public owners and fuel users across the state, from Burlington, Essex Junction and St. Albans to Montpelier, Rutland and Brattleboro, with fuel, process and water tanks designed, built, delivered and installed under one contract. Based today at 256 Shore Drive, Kilmarnock, Virginia, after earlier years in northern New Jersey and then Pennsylvania, Paul Industries works as an East Coast contractor across Vermont, the rest of New England and all 50 states.

Owners take supply-only delivery of a listed or code-built tank, design-build where Paul Industries develops the tank and site design together, or complete installation with pad, piping, alarms, permits and startup. Boiler fuel systems connect with boiler repair in Vermont. Neighboring rules are covered on tank fabrication in Massachusetts, and the headquarters state’s program on tank fabrication in Virginia. The national scope is on the tank fabrication service page, and the state overview is on the Vermont page.

Tank fabrication and installation from Paul Industries for Vermont sites

Paul Industries builds and installs Vermont tanks from the first sketch to the first delivery or the first batch: design, materials, welding, finishing, testing, delivery, foundation, anchoring, piping, alarms, insulation and the records each program expects. For tank fabrication, Vermont owners send the contents, volume, location, indoor or outdoor setting and any existing tank details, then request a quote.

Standards referenced: Vermont Aboveground Storage Tank Rules (ANR, effective August 1, 2024) · Vermont Underground Storage Tank Rules (ANR, effective October 26, 2020) · 10 V.S.A. Chapter 59 · 2025 Vermont Fire and Building Safety Code (NFPA 1 and NFPA 101, 2021; IBC 2021) · NFPA 30, NFPA 30A (2021) and NFPA 31 · NFPA 22 · PEI RP100 (2017) and PEI RP 1000 · UL 58, UL 142, UL 1316, UL 1746 and UL 180 · STI-P3, STI F841 and STI ACT-100 · API 650 and API 620 · AWWA D100 and AWWA D120 · 3-A Sanitary Standards

Frequently asked questions

Which stainless tanks does Paul Industries build for creameries around St. Albans and Swanton?

Paul Industries builds and installs stainless milk silos, balance tanks, mix tanks and clean-in-place tanks for dairy, ice cream and food plants in St. Albans, Swanton and Franklin County. Each tank is finished, drained and fitted for full cleaning coverage, and installation is staged around milk receiving so the plant keeps running. Paul Industries ties the new tank into the plant’s process and cleaning piping.

Does Paul Industries fabricate fermenters and brite tanks for breweries in Waterbury, Stowe and Burlington?

Paul Industries fabricates and installs fermenters, brite tanks, hot and cold liquor tanks and clean-in-place tanks for breweries, cideries and distilleries in Waterbury, Stowe, Burlington and across Vermont. Tanks are sized to the cellar’s ceiling, door and floor limits, with glycol jackets, cleaning devices and sanitary fittings. A tank built for more than 15 psi becomes a pressure vessel under Vermont’s code, which the design accounts for.

Can Paul Industries build generator and heating oil tanks for hospitals and state buildings in Montpelier and Barre?

Paul Industries builds and installs generator diesel and heating oil tanks for hospitals, state buildings, schools and offices in Montpelier, Barre and central Vermont. Each tank meets the 2024 AST Rules, with the concrete pad, overfill alarm, metallic fill and vent and snow protection they require, and Paul Industries prepares the Division of Fire Safety permit drawings for public buildings.

Who supplies fuel and process tanks to plants in Rutland, Springfield and Brattleboro?

Paul Industries supplies and installs fuel, process and water tanks for manufacturers, hospitals and public buildings in Rutland, Springfield, Brattleboro and Bennington. Sites in river valleys check flood hazard maps first, since tanks there need anchoring and raised vents. Paul Industries surveys existing tanks against the July 1, 2030 upgrade list and prices replacement where it is the better value.

What are the Vermont fuel tank regulations for a new generator tank at a manufacturing plant?

Vermont fuel tank regulations for an aboveground generator tank come from the Agency of Natural Resources AST Rules: an approved tank design, a concrete pad at least 4 inches deep and 10 percent larger than the tank, an overfill alarm, metallic fill and vent pipe, a shutoff valve and gauge, and snow protection outdoors. Fire code permits apply to aboveground flammable and combustible liquid tanks. Paul Industries builds and installs the tank to both.

Which above ground fuel tank regulations apply to a gasoline dispensing tank at a Vermont facility?

An aboveground gasoline tank for fuel dispensing at a Vermont facility falls under the AST Rules and under NFPA 30A as the 2025 fire code amends it. The amendment requires any aboveground tank storing Class I liquids for dispensing to be a fire resistant tank, located by the NFPA 30A separation table. Paul Industries supplies the listed tank, prepares the permit drawings and installs the dispensing system.

Who performs a Vermont fuel tank inspection, and when?

The fuel carrier performs the Vermont fuel tank inspection on aboveground petroleum tanks: after installation before the first delivery, right after the first delivery, before the first delivery after a change of carrier, at least every four years, and at removal. Used oil tanks are excluded from carrier inspections. Paul Industries corrects the deficiencies a carrier inspection finds, from pads and vents to alarms and lines.

What do double wall fuel tank regulations require for a new buried tank in Vermont?

Vermont’s UST Rules require secondary containment on every new category one and category two underground tank, and a double-walled tank must be designed so a leak through the inner wall is readily detected. Steel double-walled tanks follow STI F841, steel tanks carry UL 58 construction with an approved corrosion protection system, and installation follows PEI RP100. Paul Industries supplies and installs the tank under the construction permit.

Does a buried heating oil tank at a Vermont public building need to be registered?

A buried heating oil tank at a Vermont public building is a category three tank under the UST Rules and must be registered with the Agency of Natural Resources, as must any on-premises heating oil tank over 1,100 gallons. Smaller heating oil tanks at private sites stay outside registration. Paul Industries replaces such tanks with registered underground systems or with aboveground tanks that meet the AST Rules.

How long does a Vermont UST construction permit last?

A Vermont construction permit for a category one underground tank system is valid for up to one year from issuance, and the Secretary may allow the system to operate for up to 30 days after installation under it. The operating permit that follows lasts up to five years, with the fee paid each year. Paul Industries plans installation inside the construction permit’s term.

How must a fuel tank be anchored in a Vermont flood hazard area?

A new fuel tank in a Vermont flood hazard area is anchored to its pad by bolted foot flanges, cast-in concrete anchors with hold-down straps, earth augers with straps, or another method the tank maker or installer recommends, and its vent pipe rises above the projected flood level. Straps carry turnbuckles and sit over the anchor points. Paul Industries designs anchoring for buoyancy at the flood depth.

Can PVC vent pipe stay on an existing Vermont oil tank?

PVC vent pipe on an existing Vermont oil tank must be replaced, because the 2024 AST Rules require metallic fill and vent pipes on all aboveground systems and prohibit PVC and other non-metallic materials. Existing systems have until July 1, 2030 to meet the new fill and vent construction rules. Paul Industries replaces fill and vent piping with steel, threaded or UL 180 press-connect, and adds the overfill alarm where missing.

What snow and ice protection do outdoor fuel tanks need in Vermont?

Outdoor fuel tanks in Vermont must be protected from snow and ice falling from buildings by placing them on a gable end or away from the structure, inside a secondary containment structure, under a roofed shelter or enclosure, or by another method the Secretary approves. Existing tanks have until July 1, 2030 to comply. Paul Industries designs the tank location and any shelter with the building’s roof lines in view.

How often should storage tanks be inspected at a Vermont dairy or brewery?

Fuel tanks at a Vermont dairy or brewery follow the AST Rules carrier inspections, at least every four years, while stainless process tanks are inspected under the plant’s sanitation and maintenance program, with welds, finishes, spray devices, gaskets and vents checked on a set schedule. Cleaning coverage is worth rechecking after any change to a spray device or flow rate. Paul Industries repairs welds and finishes and passivates repaired stainless.

When does a Vermont tank become a pressure vessel?

A Vermont tank becomes a pressure vessel when it holds pressure from an external source above 15 psi, the line Section 7 of the 2025 Vermont Fire and Building Safety Code draws. Above that line, the tank is built to the ASME code and inspected by a commissioned inspector before service. Paul Industries designs each tank for its true operating and relief pressure and builds it to the matching code.

Which records come with a new tank from Paul Industries in Vermont?

A new Vermont tank from Paul Industries comes with its listing or code data, material and weld records, test results, drawings, finish and passivation records for stainless, the installation date tag on petroleum tanks, and the permit or registration documents its program requires. Food plants also receive the surface finish and cleaning coverage records their audits expect. Paul Industries keeps the set consistent so later inspections start from a complete file.

What should a Vermont owner gather before a tank is priced?

A Vermont owner pricing a tank should gather the contents, volume, operating temperature and pressure, indoor or outdoor location, a site plan or photos, flood map status, any existing tank data and the program it falls under. Process tanks add finish, cleaning and jacket requirements. Paul Industries uses that set to give a budget range and then a firm price once the design is fixed.

Planning a new, upgraded or replacement tank in Vermont?

Send the contents, volume, site photos and any existing tank data. Call 201-450-8280 or request a quote.