Paul Industries designs, builds and services ultrapure water systems in New Jersey for pharmaceutical and biotech plants, research laboratories, electronics and photonics makers and power producers, from pretreatment and reverse osmosis through electrodeionization, polishing and the distribution loop. New Jersey feedwater brings its own design problems: chloraminated utility water with a seasonal switch to free chlorine, the country’s first state limits on PFAS in drinking water, and three very different source regions between the Highlands and the Coastal Plain. Formerly based in northern New Jersey and now headquartered at 256 Shore Drive in Kilmarnock, Virginia, Paul Industries builds and expands ultrapure plants across the state.

Request a quote or call 201-450-8280

Headquarters 256 Shore Drive, Kilmarnock, Virginia
Central Jersey feed Chloraminated, with a spring switch to free chlorine (NJ American Water)
State PFAS limits PFNA 13, PFOA 14, PFOS 13 ng/L (NJDEP MCLs)
Electronics grade 18.2 megohm-cm at 25 C, TOC near 1 ppb
Industrial power 11.93 cents/kWh, against a US average of 8.13 (EIA, 2024)
Reviewed November 2026

Where are ultrapure water systems in New Jersey used?

Ultrapure water systems in New Jersey serve four groups of users: pharmaceutical and biotech manufacturing, university and corporate research laboratories, electronics, photonics and specialty device makers, and power and industrial plants that need very pure boiler makeup or process water. The pharmaceutical industry in New Jersey accounts for many of these systems, with plants and laboratories concentrated in Middlesex, Somerset, Mercer, Morris and Union counties and along the Route 1 corridor between New Brunswick and Princeton.

Research demand is growing around the same corridor. Nokia Bell Labs is building a 10-story, roughly 370,000 square foot headquarters at the HELIX campus in New Brunswick, next to Rutgers, due to open in 2028 after more than 80 years in Murray Hill, and Rutgers, Princeton, NJIT, Rowan and Kean all run research programs that depend on reagent-grade water. The national definition of grades and treatment stages is set out on the ultrapure water systems page; the sections below cover what New Jersey water, rules and sites change.

Ultrapure water users in New Jersey and what each typically specifies
UserWhere in New JerseyTypical water quality basisSystem emphasis
Pharmaceutical and biotech manufacturingRoute 1 corridor, Somerset, Morris, Union and Mercer countiesUSP Purified Water and Water for Injection monographs, often with tighter internal limitsSanitary stainless loops, sanitization, validation records
University and corporate research labsNew Brunswick, Piscataway, Princeton, Newark, GlassboroASTM D1193 Type I at the point of use, 18.0 megohm-cm minimumCentral loop with point-of-use polishers, low TOC, bacteria control
Electronics, photonics and specialty devicesResearch parks and light industrial sites statewideSEMI F63 and ASTM D5127 guides, 18.2 megohm-cm and TOC near 1 ppbPolymer loops, degassing, particle and silica control
Power and industrial steamGenerating stations and large plants with high-pressure boilersBoiler maker and turbine chemistry limits for makeup waterLarge RO and EDI trains, silica and sodium control

How does New Jersey source water change the treatment train?

New Jersey source water changes the treatment train because the state draws on three distinct supplies, and each sends a different load to the pretreatment and reverse osmosis stages. Reservoir systems in and below the Highlands, including Wanaque, Newark’s Pequannock reservoirs, Jersey City’s system and the Raritan Basin, supply about half of New Jersey residents; central utilities also treat river water from the Raritan and Millstone; South Jersey draws on the Delaware River and on Coastal Plain aquifers.

Raritan River water quality and Delaware River water quality both swing with the seasons: storm runoff raises turbidity and organic matter, warm summer water carries more biological activity, and road salt has pushed chloride upward over decades, with a U.S. Geological Survey study finding rising road-salt chloride at all 28 long-term New Jersey stream sites it examined. A plant fed from New Jersey American Water’s Delaware River Regional plant in Delran, which serves Burlington, Camden and Gloucester counties, receives river water that the utility has upgraded with advanced oxidation to treat 1,4-dioxane. Groundwater in the unconfined Kirkwood-Cohansey aquifer of the Coastal Plain is corrosive, acidic, soft and low in alkalinity, according to the U.S. Geological Survey, so South Jersey well supplies need pH and corrosion control in the pretreatment as well as iron management where it occurs.

New Jersey feedwater sources and the pretreatment each one calls for
SourceAreas servedCharacter for an ultrapure plantPretreatment emphasis
Highlands reservoirs (Wanaque, Newark’s Pequannock system, Jersey City)Much of North Jersey, Newark and Hudson CountySurface water with seasonal organics and algaeOrganics removal, TOC reduction ahead of RO, biofouling control
Raritan and Millstone river water (Raritan-Millstone and Canal Road plants)Essex, Hunterdon, Mercer, Middlesex, Morris, Somerset and Union countiesChloraminated, with a spring switch to free chlorine; winter chloride from road saltCatalytic carbon or reducing agent sized for chloramine, ORP monitoring, ammonia handling
Delaware River (Delran regional plant)Burlington, Camden and Gloucester countiesRiver water with seasonal turbidity and temperature swingsFiltration sized for storm events, antiscalant dosing reviewed seasonally, conservative RO recovery
Coastal Plain groundwater (Kirkwood-Cohansey and deeper aquifers)Much of South Jersey and the ShoreAcidic, soft, low alkalinity in the unconfined aquifer; iron in placespH adjustment, iron removal, carbon dioxide control ahead of EDI

Groundwater in the unconfined Coastal Plain aquifer is soft, while other supplies differ, so nj water hardness varies from town to town and season to season, and the design starts with the utility’s own data. Paul Industries asks for the latest New Jersey American Water quality report, or the report of whichever utility serves the site, together with a year of the plant’s own feedwater tests, and sizes softening, antiscalant dosing and RO recovery from those numbers rather than from a statewide average.

Chloramine and the spring free chlorine switch

Chloramine and the spring free chlorine switch are the New Jersey feedwater issue ultrapure plants feel most, because New Jersey American Water has disinfected with chloramines since the 1970s and switches its central and northern surface water plants to free chlorine for about ten weeks each year as routine distribution maintenance. In 2026 the switch ran from the week of February 9 to the week of April 20, when the Raritan-Millstone plant in Bridgewater resumed chloramine.

Both disinfectants must be removed before polyamide reverse osmosis membranes, which oxidize when exposed to chlorine, but they behave differently. Chloramine reacts slowly with activated carbon, so carbon beds need longer contact time or catalytic carbon to remove it, and the ammonia released passes partly through the RO as ammonium, adding load to the electrodeionization stage or mixed beds. Free chlorine is removed easily by carbon or sodium bisulfite, but its higher oxidizing strength gives less margin if a carbon bed is exhausted. A New Jersey train is therefore designed for both conditions: carbon sized for chloramine, a reducing agent backup, oxidation-reduction potential and total chlorine analyzers ahead of the RO, and an alarm plan for the weeks the utility switches over. Paul Industries also reviews carbon change-out and bisulfite dosing before each switch, so the plant enters the free chlorine period with fresh margin.

PFAS limits and New Jersey ultrapure water

PFAS limits matter to New Jersey ultrapure water because the state set the first drinking water limit for any PFAS in the United States, a 13 nanogram per liter limit for PFNA adopted in 2018, followed by limits of 14 nanograms per liter for PFOA and 13 for PFOS published in 2020. Utilities treat to those limits, but trace PFAS can still reach a plant, and pharmaceutical, laboratory and electronics users increasingly want to know where those compounds go inside their own systems.

Reverse osmosis is the main barrier: EPA describes high-pressure membranes such as reverse osmosis as extremely effective at removing PFAS, and polishing beds downstream take out much of what remains. The compounds rejected by the RO leave in the concentrate stream, so the reject flow carries them to the sewer or to reuse at a higher concentration than the incoming water. Paul Industries reviews that stream against the site’s sewer use permit and, where the owner wants it, adds granular activated carbon or ion exchange on the feed or on the reject, so PFAS are captured in a bed that can be changed out and disposed of under control.

What goes into an ultrapure water system in New Jersey?

An ultrapure water system in New Jersey follows the same basic train as anywhere, pretreatment, reverse osmosis, electrodeionization, polishing and a recirculating loop, with each stage tuned to the feedwater and rules described above. The table follows a typical train for a laboratory or electronics loop and notes the New Jersey adjustment at each step.

Ultrapure treatment stages with the New Jersey adjustment at each step
StagePurposeNew Jersey adjustment
Multimedia or ultrafiltrationRemove suspended solids and colloidsSized for storm turbidity on river-fed supplies
Activated carbon or bisulfiteRemove disinfectant and some organicsCatalytic carbon or long contact time for chloramine; reducing agent backup for the free chlorine weeks
Softening or antiscalantProtect RO from scaleSet from the utility’s hardness and the site’s own tests; adjusted for winter chloride
Double-pass reverse osmosisRemove most dissolved ions, organics, bacteria and PFASRecovery and reject handling reviewed against sewer permits and PFAS concerns
Membrane degassingRemove carbon dioxide and dissolved oxygenImportant on acidic Coastal Plain groundwater with high free carbon dioxide
ElectrodeionizationContinuous polishing toward 16 to 18 megohm-cmFeed limits on ammonia and carbon dioxide checked against chloraminated supply
UV, polishing resin, final filtrationLower TOC, remove trace ions and particlesResin change-out planned with feed seasonality in mind
Storage and distribution loopDeliver water at quality to every point of useNitrogen blanket, constant velocity, sanitization access in occupied labs

Ultrapure water through a New Jersey year

Ultrapure water through a New Jersey year meets four distinct seasons of feedwater, and a plant designed for one of them can struggle in another. Winter brings the coldest feed, which lowers reverse osmosis flux and can leave a train short of capacity unless the membrane area or feed heating was sized for it. Late winter and spring bring the utility’s free chlorine weeks on chloraminated supplies, snowmelt runoff and elevated chloride from road salt on river-fed systems.

Summer brings the warmest water, which raises flux but also biological growth in carbon beds, storage tanks and any dead leg, so sanitization intervals and carbon bed hygiene matter most from June to September. Autumn leaf fall and storms lift organic matter and turbidity in reservoir and river supplies, which shows up as higher TOC ahead of the RO and faster fouling of pretreatment filters. Paul Industries sizes each train against the hardest season for that stage rather than the annual average: membranes for January feed, carbon for chloramine and the free chlorine weeks, sanitization for August and filtration for autumn storms. Seasonal service visits then follow the same calendar, so membranes are cleaned, carbon is checked and analyzers are calibrated ahead of the season that will test them.

Expanding an ultrapure plant at an operating New Jersey site

Expanding an ultrapure plant at an operating New Jersey site is a frequent project in the state, because pharmaceutical manufacturers in New Jersey and the research campuses around them tend to grow inside existing buildings rather than on new land. An expansion adds a generation train, a larger storage tank or new loop branches while the existing loop keeps supplying production or research.

Paul Industries plans those tie-ins around a short, scheduled outage or a hot connection at an existing valve, prefabricates new loop sections and skids in the shop, and tests, flushes and sanitizes each new section before it joins the live loop. For validated pharmaceutical systems the new section goes through installation and operational qualification and a sampling period before release, which is described on validation and commissioning in New Jersey. Purified water systems for cosmetics and personal care, which have their own preservative and batch-draw problems, are covered on high-purity water systems in New Jersey.

Loop materials and installation practice in New Jersey plants and labs

Loop materials and installation practice in New Jersey plants and labs follow the end use: electropolished 316L stainless steel with orbital welds for pharmaceutical loops that are hot-water or steam sanitized, and high-purity polymers such as PVDF for electronics and many laboratory loops where metal ions must stay at trace levels. Polymer loops are joined by fusion welding with smooth internal beads; stainless loops are welded to ASME BPE practice, borescoped and passivated before use.

Paul Industries installs both, with the weld logs, borescope records, pressure tests and cleaning records each owner needs, and passivates stainless systems as described on passivation services in New Jersey. Stainless distribution work in pharmaceutical buildings is covered in more depth on sanitary process piping in New Jersey, and the rooms that ultrapure water often feeds on cleanrooms in New Jersey.

Deionized water and other water purification systems in New Jersey plants

Deionized water and other water purification systems in New Jersey plants often share a building, a feedwater supply and an operations team with the ultrapure system, so they are best planned together. Rinse water for parts washing, makeup for low and medium pressure boilers, humidifier water and laboratory glassware washing rarely need 18 megohm-cm water; a single-pass RO with a mixed-bed or EDI polisher, or a two-bed deionizer, meets them at far lower cost. Supplying deionized water in New Jersey plants from its own header also protects the ultrapure loop, because high-volume, intermittent draws upset loop velocity and quality.

Paul Industries designs the split: which users stay on the ultrapure loop, which move to a deionized water header, and which can take softened or RO water directly. Equipment for the lower grades is described on industrial DI water systems, and filter housings and cartridge selection on high-purity water filtration. On sites with chloraminated feed, one shared carbon and dechlorination stage can serve every grade, which simplifies the spring free chlorine period to a single set of checks.

Monitoring and records New Jersey quality teams expect

Monitoring and records New Jersey quality teams expect from an ultrapure system start at the feed and end at the farthest point of use. Ahead of the reverse osmosis, oxidation-reduction potential and total chlorine analyzers prove the disinfectant is gone, which matters most during the utility’s free chlorine weeks. After the RO and EDI, conductivity and resistivity trend the ion removal. On the loop, resistivity, TOC and, for electronics users, particle counters and dissolved oxygen analyzers confirm quality where it is used, while flow and temperature at the loop return confirm velocity and sanitization conditions.

Pharmaceutical sites add sampling plans, alert and action limits and trending under their quality systems, and laboratories increasingly want the same discipline for Type I water feeding sensitive instruments. Paul Industries installs and calibrates the analyzers, ties them into the plant control system, and delivers calibration certificates, loop drawings and sampling point lists with the turnover, so the first audit after startup finds a complete record.

Checks before and during New Jersey’s free chlorine period on a chloraminated supply
WhenCheckWhy it matters
Two to four weeks before the utility’s switchCarbon bed condition, bisulfite stock and pump, analyzer calibrationFresh margin before a stronger oxidant arrives
First days of free chlorineTotal chlorine and ORP ahead of the RO, RO salt passageBreakthrough shows here first, before membranes are harmed
Through the free chlorine weeksTrend ORP alarms, carbon differential pressure, bisulfite consumptionConfirms the dechlorination stage is keeping pace
After chloramine returnsAmmonia and conductivity after the RO, EDI or mixed-bed loadingAmmonium passing the RO raises the polishing load again
AnnuallyReview of utility notices and the year’s feedwater dataKeeps pretreatment sizing matched to the real supply

Who installs ultrapure water systems in New Jersey?

Paul Industries installs ultrapure water systems in New Jersey, designing, supplying, building, starting up and maintaining complete trains and loops for plants and laboratories in Newark, Jersey City, Edison, New Brunswick, Piscataway, Princeton, Trenton, Camden and every other part of the state. Owners can buy a complete design-build system, have Paul Industries install skids they purchase, or order prefabricated skids and loop sections for their own installation. Whichever route the owner picks, Paul Industries carries the work through pressure testing, flushing, sanitization and startup, trains the operators who will run the plant, and stays on for membrane, resin and analyzer service so the system that passed its first quality check keeps passing year after year. Expansion space, spare tie-in valves and room for a future train are laid out during the first project, which makes the next phase in a growing New Jersey plant faster and cheaper.

Paul Industries also builds the full range of water treatment that sits beside an ultrapure plant on the East Coast, in all 50 states and at plants outside the United States through its international work; for the headquarters state, see ultrapure water systems in Virginia.

What sets ultrapure water system cost in New Jersey?

Ultrapure water system cost in New Jersey is set by capacity, the quality target, the feedwater, the loop length and material, redundancy, and the space available inside an existing building. A laboratory loop with point-of-use polishers is a different order of project from a double-pass RO and EDI plant feeding an electronics or biologics line, and stainless sanitary loops cost more per foot than polymer loops.

Operating cost deserves the same attention. Power for pumps and EDI stacks costs New Jersey industry an average 11.93 cents per kilowatt-hour (EIA, 2024), well above the 8.13 cent national figure, which raises the value of energy-efficient RO pumps: every 10 kilowatts of pump and EDI load running around the clock costs about $10,450 a year at that price, so variable speed drives, right-sized pumps and low-pressure membranes earn their keep quickly. The same price favors energy recovery on large trains and recovery of RO reject for cooling towers or other uses. Sewer charges on reject water, carbon and resin change-outs timed to the chloramine season, and any PFAS capture media also belong in the lifetime cost. Paul Industries prices a system from the owner’s flow, quality and feedwater data, with a budget range early and a firm price once the design is fixed.

Ultrapure water from Paul Industries in New Jersey

Paul Industries designs, fabricates, installs, starts up, validates and services ultrapure water systems across New Jersey, from pretreatment built for chloraminated and PFAS-regulated feed to polishing loops for pharmaceutical, laboratory and electronics use. Send the required flow, the water quality target, a year of feedwater data and the site layout, and Paul Industries returns a scope and budget. Call 201-450-8280 or request a quote, and see the New Jersey overview for sanitary piping, cleanroom and plant utility work in the state.

Standards referenced: SEMI F63 · ASTM D5127 · ASTM D1193 · USP Purified Water and Water for Injection monographs · New Jersey PFAS maximum contaminant levels (N.J.A.C. 7:10) · New Jersey Uniform Construction Code, N.J.A.C. 5:23 · ASME BPE · ISPE Baseline Guide: Water and Steam Systems

Frequently asked questions

Which contractor builds ultrapure water systems for labs in New Brunswick, Piscataway and Princeton?

Paul Industries builds ultrapure water systems for research labs and pilot plants in New Brunswick, Piscataway, Princeton and the rest of the Route 1 corridor. Those sites are usually fed by chloraminated Raritan-Millstone water, so the pretreatment is sized for chloramine removal and the spring switch to free chlorine, and the loop is built with point-of-use polishers where individual labs need Type I water.

Does Paul Industries build ultrapure water systems in Newark, Jersey City and the rest of North Jersey?

Yes. Paul Industries builds and expands ultrapure plants in Newark, Jersey City, Paterson, Elizabeth and the Meadowlands, where most supplies come from Highlands reservoir systems. Reservoir water brings seasonal organics and algae, so the design focuses on TOC reduction and biofouling control ahead of reverse osmosis, and on fitting equipment into older multistory buildings.

Who installs ultrapure water systems in South Jersey, from Camden and Trenton to Vineland?

Paul Industries installs ultrapure water systems throughout South Jersey and the Delaware Valley. Sites on Delaware River supply see seasonal turbidity and temperature changes, while sites on Coastal Plain wells deal with acidic, soft, low-alkalinity water and occasional iron. Each calls for different pretreatment, so Paul Industries designs from the site’s own water tests and the serving utility’s annual report.

Is New Jersey water hard enough to matter for reverse osmosis?

Is New Jersey water hard? The answer depends on the supply. USGS describes unconfined Coastal Plain groundwater as soft, while reservoir, river and deeper well supplies each carry their own hardness that shifts by season, and even moderate hardness scales RO membranes at high recovery. Paul Industries reads the utility’s water quality report and the plant’s own tests, then sets softening or antiscalant dosing and RO recovery to suit.

Where do semiconductor companies in New Jersey need ultrapure water?

Semiconductor companies in New Jersey center on specialty devices, photonics and research, and the state’s CHIPS strategy has focused on small runs of specialized chips and on research at Rutgers, Princeton, NJIT, Rowan and Kean. Those users need 18.2 megohm-cm water with very low TOC in compact systems, which Paul Industries designs and installs to SEMI F63 and ASTM D5127 guidance.

What does the semiconductor industry New Jersey hosts need from a water system?

The semiconductor industry New Jersey hosts runs at research and pilot scale more than at high-volume production, so its ultrapure systems are measured in gallons per minute rather than thousands. The quality targets stay the same: 18.2 megohm-cm, TOC near 1 ppb, tight particle, silica and dissolved oxygen limits. Compact double-pass RO, EDI, polishing and a PVDF loop usually meet them.

How does the chloramine to free chlorine switch affect an ultrapure plant in Central Jersey?

During the switch, the disinfectant reaching the plant changes from chloramine to free chlorine for about ten weeks, which is stronger but easier for carbon to remove. Plants built only for chloramine can see chlorine breakthrough if carbon is near exhaustion, risking RO membrane damage. Fresh carbon or bisulfite backup, and oxidation-reduction potential alarms ahead of the RO, protect the train through the change.

Do New Jersey's PFAS drinking water limits apply to an ultrapure water plant?

The limits apply to public water systems, which treat the water delivered to the plant. Inside the plant, the concern shifts to where trace PFAS go: reverse osmosis concentrates them in the reject stream. Paul Industries reviews that stream against the sewer use permit and adds carbon or ion exchange capture where the owner wants PFAS held in a bed rather than discharged.

Can RO reject water be reused at a New Jersey site?

Often, yes. Reject from the first RO pass is usually suitable for cooling tower makeup, and second-pass reject can return to the first-pass feed. At New Jersey water and sewer rates, recovering reject cuts two bills at once. Paul Industries checks the reject’s hardness, silica and any PFAS content against the receiving use before piping the reuse line.

Should a New Jersey pharmaceutical plant make ultrapure water and USP water from one pretreatment train?

Sharing pretreatment saves space and capital, and many plants do it, but the USP system then depends on a train that also serves non-GMP users, which affects change control and qualification. Paul Industries lays out both options with their validation implications, so pharmaceutical companies in New Jersey can weigh shared pretreatment against separate trains with full knowledge of the quality system impact.

What does ultrapure water system cost in New Jersey depend on most?

Flow and quality target come first, then feedwater, loop length and material, redundancy and the space available in an existing building. Operating cost follows electricity at 11.93 cents per kilowatt-hour, sewer charges on reject, and media replacement. Paul Industries prepares a budget range from comparable systems once flow and quality are known, then a firm price once the layout and equipment are fixed.

How long does it take to add a loop branch to a running New Jersey ultrapure system?

Most of the work happens before the outage: the branch is prefabricated, pressure tested and cleaned in the shop, and the tie-in is made in a short scheduled window or through a valve installed earlier. After connection the branch is flushed and sampled until it meets the loop’s quality. Validated pharmaceutical loops add a qualification and sampling period before release.

Which loop material should a New Jersey lab choose for 18.2 megohm-cm water?

PVDF is the usual choice for laboratory and electronics loops at that quality, because it leaches very little and joins by fusion welding with smooth internal beads. Electropolished stainless steel suits loops that need hot-water or steam sanitization, such as pharmaceutical systems. Paul Industries selects the material from the end use and sanitization method, and installs either one.

Can an older New Jersey purified water system be upgraded to ultrapure quality?

In many cases, yes, by adding a second RO pass or EDI, membrane degassing, UV for TOC reduction, polishing resin and final filtration, and by replacing loop sections whose material or dead legs limit quality. Paul Industries surveys the existing system, tests its output and proposes an upgrade path staged to keep the plant supplied while work proceeds.

How do New Jersey winters affect an ultrapure water plant?

Cold feedwater lowers RO flux, so trains designed on summer temperatures can fall short of capacity in January and February unless they have feed heating or extra membrane area. Road salt also raises chloride in surface supplies in winter and spring. Paul Industries sizes membranes for the coldest expected feed and sets antiscalant dosing for the seasonal chloride rise.

What should a New Jersey site send to get an ultrapure water system priced?

Send the required flow and peak draw, the quality target and standard, a year of feedwater data or the utility’s annual report, the loop route and points of use, space limits, and whether the system is validated. Paul Industries uses that information to size the train and loop and to return a budget range, followed by a firm proposal once the design is agreed.

How does Paul Industries keep an ultrapure system in service after startup?

Paul Industries offers service covering membrane cleaning and replacement, EDI and resin checks, carbon and filter change-outs timed to the chloramine season, analyzer calibration, loop sanitization and trend review of resistivity, TOC and particle data. Service records are organized for quality audits, and recurring problems are traced to their root in the pretreatment or the loop.

Planning an ultrapure water system or expansion in New Jersey?

Share the flow, the quality target, a year of feedwater data and where the loop must reach. Call 201-450-8280 or request a quote.