Paul Industries provides boiler repair in South Carolina for manufacturing plants, hospitals, campuses and commercial buildings, repairing firetube, watertube and cast iron boilers and returning each unit to service with the records the state Boiler Safety Act expects. South Carolina registers and inspects these units through the Department of Labor, Licensing and Regulation (LLR), with commissioned special inspectors making the inspections, so a repair often begins with an inspector’s written finding. Paul Industries diagnoses the fault, makes the repair, runs the tests and prepares the unit for the reinspection that closes the finding.

Request a quote or call 201-450-8280

Headquarters 256 Shore Drive, Kilmarnock, Virginia
State law Boiler Safety Act, S.C. Code 41-14-10 to 41-14-150
Administered by LLR Boiler Safety Program, chief boiler administrator
Power boilers Certificate inspection every year
Heating and hot water boilers Certificate inspection every two years
Filing fee $25 per boiler for each inspection report filed
Reviewed November 2026

What does boiler repair in South Carolina involve under the Boiler Safety Act?

Boiler repair in South Carolina covers tube and section leaks, refractory, burners and fuel trains, low-water cutoffs, safety valves, feedwater and condensate equipment, and welded repairs to pressure parts, all carried out on equipment that the Act of 2005 brings under state registration and periodic inspection. The Act, codified as Title 41, Chapter 14 of the South Carolina Code, has required each covered unit to be registered and inspected since 2006, and the South Carolina boiler regulations sit in Chapter 71, Article 9.

Those two documents, the South Carolina boiler law and rules, shape a repair in three practical ways: they decide which units file inspection reports with the state, they set what happens when an inspector finds one unsafe, and they spell out how it is tested and documented before it returns to service. The general repair methods, from retubing to burner tuning, are covered on the boiler repair service page. This page deals with what is particular to South Carolina, and the South Carolina overview explains how these certificates fit alongside the other records a regulated plant keeps.

South Carolina boiler law: which boilers are covered and what each owner files

The South Carolina boiler law applies to every covered vessel in the state unless the Act names an exception, and even most exceptions keep a duty to file an inspection report. Under the Act, a boiler is a closed vessel that heats water or another liquid, or makes or superheats steam, for use outside the vessel, using fuel, electricity, solar or nuclear energy. Section 41-14-60 then sorts them into three groups.

Several classes are exempt from the regulations provided a timely inspection report is filed: units at research facilities used solely for research, units that generate electricity, units that are part of a manufacturing process, units subject to OSHA standards, and units run by a public utility or the Public Service Authority, the state-owned utility known as Santee Cooper. Regulation 71-9100 says how they claim the exemption: by filing a special inspector’s report, or an insurer’s certification that identifies the unit and shows it was inspected at the right frequency. In practice, then, a South Carolina process plant still has an inspection on file for each unit; what it gains is relief from the detailed operating rules, not from inspection.

How South Carolina’s Boiler Safety Act treats each kind of boiler
Boiler or vesselStatus under S.C. Code 41-14-60What the owner keeps on file
Power boilers and heating boilers in commercial and public buildingsFully coveredRegistration, inspection reports at the required interval, $25 filing fee per boiler
Process, power generation, research, OSHA-subject and utility boilersExempt from the regulations if a timely inspection report is filedSpecial inspector’s report or insurer’s certification for each boiler
Boilers under federal control or 49 CFR Parts 192 and 193Outside the ActRecords under the federal owner’s own program
Hot water supply boilers within 200,000 Btu per hour, 210 F and 120 gallons, with ASME and National Board relief valvesOutside the ActManufacturer data and relief valve records
Farm boilers, and heating boilers in homes or apartment houses with fewer than six unitsExempt from the inspection and correction sectionsConstruction and installation records
Unfired pressure vessels (air receivers, tanks, heat exchangers)Exempt under 41-14-60(C)ASME data reports and the plant’s own inspection records

The last row matters on repair jobs because deaerators, blowdown tanks, condensate receivers and flash tanks sit right beside the firebox but fall outside the Act. They are still ASME vessels and still need sound repairs; the route for them is described on the pressure vessel fabrication in South Carolina page.

South Carolina boiler inspection intervals by boiler class

South Carolina boiler inspection intervals are set in Section 41-14-120 by class: power boilers and high-pressure, high-temperature water boilers are inspected every year, and low-pressure steam heating boilers, hot water heating boilers and hot water supply boilers every two years. A grace period of two months beyond the required interval is allowed between certificate inspections.

Plant engineers who ask how often should a boiler be inspected in this state usually want two answers: the certificate interval, and how often the boiler must be opened for an internal inspection. The table gives both. Where an inspector decides that a hydrostatic test is needed, the owner or user is responsible for making it, and Paul Industries prepares the unit and runs the test so the inspector can witness it.

Inspection intervals under S.C. Code 41-14-120 and Regulation 71, Article 9
Boiler classDefinition in the ActCertificate inspectionInternal inspection
Power boilerSteam or vapor above 15 psigEvery year, plus an external inspection under pressure where possibleEach year where construction permits; 36 months for fully attended boilers meeting the water treatment and records conditions
High-pressure, high-temperature water boilerWater above 160 psig or 250 FEvery yearEach year where construction permits
Low-pressure steam or vapor heating boilerSteam at 15 psig or lessEvery two yearsEvery four years where the installation permits
Hot water heating and hot water supply boilersWater to 160 psig and 250 FEvery two yearsAt the inspector’s discretion

The 36-month internal cycle for fully attended power boilers

The regulations let a fully attended power or high-temperature boiler stretch its internal inspection to 36 months when three conditions hold: continuous water treatment under the supervision of people trained in it, records showing every outage and daily water analysis, and controls and safety devices that are current, calibrated and in service under codes such as NFPA 85 and ASME CSD-1. The external inspection stays annual. For a plant that wants the longer cycle, the repair history matters, because a pattern of tube failures or scale suggests the water treatment is not controlling corrosion and deposits. Paul Industries backs that case with tube samples, deposit analysis and a boiler water treatment review when a repair turns up scale or oxygen pitting.

Special inspectors, insurers and the chief boiler administrator

South Carolina boiler inspections are made by special inspectors who hold a National Board commission or pass an equivalent examination, and who work for the boiler’s insurer or for a private inspection company, while the state itself keeps the records and enforces the Act through LLR. The state does not pay special inspectors; an inspector may examine units that the inspector’s own company covers or operates. A South Carolina boiler inspector also may not sell any service, article or device relating to boilers, which keeps the finding and the repair as two separate pieces of work.

At the head of the program sits the chief boiler administrator, who must have passed the same National Board style examination and who keeps the record of each unit: owner, location, type, dimensions, maximum allowable working pressure, age and last inspection. Owners and inspectors sometimes call this person the South Carolina chief boiler inspector, and the National Board lists the post that way. At first registration, the special inspector or insurer fixes a department-issued registration number to the unit in a place any inspector can see.

The South Carolina boiler safety program charges a filing fee of $25 per unit when an inspection report is filed. The boiler inspection cost charged by the inspecting company is separate from that fee, and so is the cost of preparation: draining, opening handholes and manways, cooling and cleaning the furnace, and isolating it from shared headers. Paul Industries carries out that preparation when a repair or a shutdown already has the unit open, so the inspection and the repair share one outage.

From an inspector’s finding to a boiler back on line

An unsafe finding by a special inspector in South Carolina starts a defined sequence: the inspector tells the owner what repairs or corrective measures are needed, and if they are not made promptly, the inspector notifies the chief boiler administrator, who may order it out of operation until a reinspection shows it is safe. Section 41-14-130 also lets LLR take a unit out of service where faulty installation or incorrect repair has made it hazardous, so the quality of the repair is part of the legal picture.

The path from a South Carolina inspection finding to a closed record
StepWhat happensWhat Paul Industries doesRecord produced
1. FindingSpecial inspector notes the defect and the corrective measure requiredReads the finding, inspects the boiler and scopes the repairInspection report and repair scope
2. Repair planRepair method agreed; inspector consulted before any welding on pressure partsPrepares the repair procedure, materials and outage planWritten repair plan and material records
3. RepairWork carried out to the NBIC and the original code of constructionMakes the repair and keeps weld and inspection recordsNBIC repair report for welded work
4. TestPressure test where required, with safety valves removed or gagged with a testing clampFills, pressurizes and holds the test for the inspectorTest record
5. ReinspectionInspector confirms the boiler is safe; administrator notified; any cessation order rescindedRestores controls, fires the boiler and checks safeties under loadReinspection report filed with LLR

Where the defect involves riveted construction, the regulations draw one hard line: a lap seam crack along a longitudinal riveted joint takes the shell or drum out of use, and patching is prohibited. That rule rarely reaches modern plants, but it does reach historic and older heating boilers, and it turns a repair question into a replacement plan.

Code repairs, the NBIC and the pressure test in South Carolina

The South Carolina boiler code points to the ASME Boiler and Pressure Vessel Code for construction and to the National Board Inspection Code for repairs and alterations, and the regulations say that conditions they do not cover fall under the ASME Code, the NBIC or the API inspection code. A welded repair to a pressure part is made under the National Board R program with the inspector consulted before work starts, and is documented on an NBIC repair report that stays with the unit’s records.

The regulations add practical rules for the test that follows. A pressure test need not exceed the maximum allowable working pressure or the setting of the lowest safety valve, the pressure must stay under control so the test value is never exceeded, and safety valves are either removed or held shut with a testing clamp, never by screwing down the compression screw. Metal temperature during the test is suggested to be at least 70 F, and no more than 120 F during inspection. The owner prepares for the test on a date the inspector sets, at least seven days after notice, so Paul Industries builds that lead time into the repair schedule. Weld procedures and examination for pressure-part repairs are covered on the industrial welding services in South Carolina page.

Low-water cutoffs, safety valves and firing controls

Every automatically fired steam boiler in South Carolina must have an automatic low-water fuel cutoff set to stop the fuel when the water drops to the lowest safe waterline, and hot water heating boilers need a low-water fuel cutoff with a manual reset. Those devices, the safety valves and the flame safeguard are the parts most often replaced on a service call. The regulations bar anyone from working on a safety appliance while it is under pressure, require any appliance removed during an outage to be back in place and working before the unit returns to service, and forbid altering a safety or relief valve to hold a pressure above the figure on the inspection report. Paul Industries replaces cutoffs and valves like for like or to the current code, tests them by draining down or lifting under pressure as the device requires, and records settings and serial numbers for the next inspector.

After a boiler accident: reporting and the six-hour window

A boiler accident in South Carolina that injures anyone, or that forces an emergency shutdown, must be reported promptly to the chief boiler administrator with a detailed report, and an injury or explosion must be reported by telephone or accepted electronic means immediately. Nothing on the unit may be removed or disturbed until LLR gives permission, except to save life or limit further damage.

The regulations then give owners a way forward: if LLR cannot respond within six hours, the owner may proceed with repairs but must document the conditions as found. Paul Industries treats that documentation as the first task on the job, photographing and measuring the damage, preserving failed parts, recording control settings and alarm history, and noting water level and fuel valve positions before anything is moved. That record serves the state, the insurer and the root cause review, and it lets the repair begin without losing evidence. Injuries also bring in SC OSHA, the state plan that LLR runs for private employers and state, county and city government workplaces.

Replacing, renting or relocating a boiler in South Carolina

Any new boiler installed in the state must be built to the ASME Code or another nationally recognized code accepted by the state, carry the code marking and be registered with the National Board, and its installation goes forward under a mechanical permit from the city or county. The National Board synopsis for South Carolina adds that the National Board I-1 installation report and the manufacturer’s start-up sheets go to the owner’s file, where an inspector can review them. South Carolina’s contractor licensing law defines a Boiler Installation subclassification covering installation, repair and service of boilers, their piping, controls and auxiliary equipment, and requires a license for mechanical contracting above $10,000; a South Carolina boiler license, in that law, is a contractor classification rather than an operator credential.

A boiler changeout with a used unit needs more steps. Before a secondhand unit is shipped for installation in South Carolina, an inspector holding a National Board commission inspects it, the data goes to the chief boiler administrator and the building official, and the chief’s permission is obtained before installation; the fittings and appurtenances must then meet the rules for new installations. A standard unit sent out of state for repair needs permission to be reinstalled, and a nonstandard one that leaves the state may not come back. A rental unit arrives with its National Board registration and latest inspection report, and is inspected and tagged by the agency that normally inspects at that location.

Paul Industries supplies replacement units, installs owner-furnished ones and handles the whole changeout: removal, rigging, piping, fuel train, controls, deaerator and feedwater tie-ins, startup and the installation paperwork. Steam and condensate lines tied to the new unit are covered on the process piping in South Carolina page.

Burner work, fuel changes and SC DES air permits

Burner and fuel work on a South Carolina boiler can trigger an air permit question with the South Carolina Department of Environmental Services (SC DES), which took over the environmental programs of the former DHEC on July 1, 2024. Under Regulation 61-62.1, boilers and space heaters under 10 million Btu per hour that burn only virgin gas fuels need no construction permit, and the cutoff for units burning only virgin liquid or solid fuels is 1.5 million Btu per hour, in both cases unless another state or federal requirement applies.

A like-for-like burner repair stays within the existing permit. A change of fuel, a larger replacement or a switch from gas to dual fuel can move a unit past those thresholds, and the permit work then belongs at the front of the schedule. Package boilers of 100 million Btu per hour or less on natural gas or virgin oil that match a prototype a professional engineer has already designed or approved are spared the engineer’s seal on the application. Federal rules sit alongside: oil, coal and biomass units at area sources carry tune-up duties under 40 CFR Part 63, Subpart JJJJJJ, while gas-fired units fall outside that subpart. Paul Industries records combustion analysis before and after burner work so the plant’s permit file shows the unit’s emissions condition.

What industries use steam boilers in South Carolina?

Tire plants, textile finishing, food and beverage processing, pharmaceuticals, paper, chemicals, hospitals and universities are the South Carolina industries that use steam boilers most heavily, and each one brings its own repair pattern. Tire manufacturing is the clearest example: South Carolina is home to Michelin’s North American headquarters in Greenville and Michelin plants across the state, two Bridgestone plants in Aiken County, Continental in Sumter and Giti in Richburg. Curing presses there shape and vulcanize each tire with steam and nitrogen inside a bladder, so high-pressure steam from the powerhouse is tied directly to output.

That steady, high-pressure demand wears on steam generators in predictable ways: tube erosion and overheating where firing rates stay high, condensate return problems that raise makeup water and scale, and cycling damage where presses open and close many times an hour. Steam distribution faults, such as failed traps flooding headers, often show up first as trouble in the powerhouse; the steam trap page covers that side.

South Carolina regions, the boilers they run and the repair work that follows
RegionTypical boiler usersCommon repair work
Greenville, Spartanburg and the UpstateTire, automotive supplier, textile and food plantsWatertube repairs, burner tuning, low-water cutoff and control upgrades
Columbia and the MidlandsState buildings, university and hospital central plants, manufacturingFiretube retubes, refractory, deaerator and feedwater work
Charleston, North Charleston, Summerville and Berkeley CountyAerospace and port-side industry, hospitals, food and beverage plantsCorrosion repairs on outdoor equipment, condensate systems, replacements
Florence and the Pee DeePaper, food processing and manufacturing plantsHigh-duty steam boiler overhauls, tube work, safety valve programs
Aiken and the Savannah River areaTire and industrial plants; federal installations under their own programsProcess boiler repairs with inspection reports filed for the exemption
Rock Hill, York County, Myrtle Beach and BeaufortManufacturing, hotels, hospitals and military-adjacent facilitiesHeating boiler sections, hot water boilers, burner and control repairs

Boiler repair, Charleston, SC: Lowcountry plants and hospitals

Plants in Charleston, North Charleston and Summerville sit in salt air and heavy humidity, which attack outdoor stacks, breechings, fuel train components and electrical enclosures long before the pressure parts show wear. Paul Industries checks those exposed parts on every repair visit there and plans replacements of corroded burner and control components before they cause a trip.

Boiler repair, Columbia, SC and the Midlands

Columbia hosts large heating plants serving government buildings, campuses and hospitals, where firetube boilers run long winter seasons and stand in reserve through summer. Retubes, refractory work and section replacement are planned for the warm months, when one boiler can come offline without risking heat or hot water.

Boiler repair, Greenville, SC and the Upstate

Upstate plants run process steam around the clock, so repairs follow production calendars and annual shutdowns. Paul Industries pairs the repair with the certificate inspection where the timing allows, so the boiler is opened, repaired, tested and inspected in a single outage.

Repair or replace an older South Carolina boiler

An older South Carolina unit is worth repairing when the pressure parts are sound, the burner and controls can be brought to current safety standards, and the unit still matches the load; it is worth replacing when tube failures repeat, the shell shows thinning, or the load has changed so much that it cycles constantly. The state rules add their own weight: riveted construction with a lap seam crack must come out of service, a condemned unit is stamped XXX beside its South Carolina number, and a replacement triggers the installation requirements for new units, the permit and possibly an air permit review.

Paul Industries prices both paths together, so the owner sees the repair cost, the expected remaining life and the full replacement scope side by side. For campuses and hospitals, the comparison also covers how the plant keeps heat and hot water during a changeout, which may mean a rental unit with its own inspection and tag.

Boiler repair in South Carolina: what sets the price

The price of boiler repair in South Carolina is set by the type and size of the unit, the extent of the damage found once it is opened, the materials and parts needed, whether welded pressure-part work and an inspector’s acceptance are involved, the testing required, and how much of the work must fit into a fixed outage. Access matters too: an equipment room with a clear path for tubes and a removable wall costs less to retube than one where the tubes must be cut and fed through a narrow door.

State costs are small and predictable. LLR charges $25 per unit when the inspection report is filed, and the penalties are the real exposure: up to $5,000 per violation and up to $100 a day for failing to comply after written notice. South Carolina has no state prevailing wage law, so public owners price labor without a state wage schedule unless federal funding brings one. Paul Industries gives a budget range from comparable work once the nameplate data and the finding are in hand, then a firm price after inspection of the opened unit.

Who repairs boilers in South Carolina?

Paul Industries repairs boilers in South Carolina, working at plants, hospitals, campuses and commercial buildings across the state as an East Coast contractor headquartered at 256 Shore Drive, Kilmarnock, Virginia. Formerly based in northern New Jersey and then Pennsylvania, the company takes work throughout the Southeast and in all 50 states, including boiler repair in Virginia, its headquarters state, and work under the separate state programs described on the North Carolina and Georgia pages.

For South Carolina owners, Paul Industries offers each route the job needs: repair of the existing unit, supply of parts or a complete replacement, design-build of a new boiler room, and complete installation with startup. Paul Industries also repairs the chilled water side of a central plant, covered on the chiller repair in South Carolina page, and on the fuel and water tanks around it, covered on the tank fabrication in South Carolina page.

Boiler work from Paul Industries across South Carolina

Paul Industries diagnoses, repairs, retubes, rebuilds, tests, replaces and services steam and hot water plants for South Carolina owners, from Upstate tire plants to Lowcountry hospitals, and leaves each job with the repair reports, test records and settings a special inspector needs to close a finding. To start, send the make, model, National Board and South Carolina numbers, its pressure and fuel, the latest inspection report and any finding, and request a quote or call 201-450-8280.

Standards referenced: South Carolina Boiler Safety Act, S.C. Code 41-14 · S.C. Regulation 71, Article 9 (Boiler Safety Program) · ASME Boiler and Pressure Vessel Code, Sections I and IV · National Board Inspection Code (NBIC) · ASME CSD-1 · NFPA 85 · SC DES Regulation 61-62.1 · 40 CFR 63 Subpart JJJJJJ

Frequently asked questions

Who handles boiler repair for plants in Greenville, Spartanburg and Anderson?

Paul Industries handles boiler repair for plants in Greenville, Spartanburg, Anderson and the rest of the Upstate, from tire and automotive supplier plants to textile and food processors. Upstate process boilers usually run continuously, so repairs are planned into annual shutdowns and paired with the certificate inspection where the timing works. Send the boiler data, the last inspection report and any finding, and Paul Industries scopes the repair and the outage.

Does Paul Industries repair boilers in North Charleston, Summerville and Berkeley County?

Yes. Paul Industries repairs boilers in North Charleston, Summerville, Goose Creek, Moncks Corner and the rest of Berkeley and Dorchester counties, at aerospace, food and beverage, chemical and hospital sites. Salt air near the harbor shortens the life of stacks, breechings, fuel trains and control enclosures, so those parts are inspected on every visit along with the pressure parts.

Who repairs boilers for plants in Florence, Darlington and the Pee Dee?

Paul Industries repairs boilers for paper, food processing and manufacturing plants in Florence, Darlington, Hartsville and the wider Pee Dee. High-duty steam boilers in the region need tube work, refractory repairs and regular safety valve programs, and the repair plan follows the plant’s production calendar. Paul Industries prepares the boiler for the special inspector’s visit so the repair and the inspection share one outage.

Does South Carolina require a boiler operator license?

The South Carolina Boiler Safety Act regulates boilers and the special inspectors who examine them, and it contains no provision for a South Carolina boiler operator license. What the Act does require is registration, periodic inspection and a filed report for each covered boiler. Plants still keep operator training and logs, because water treatment records and attended operation decide whether a power boiler qualifies for the longer 36-month internal inspection cycle.

Is there a South Carolina boiler lookup for registration records?

LLR keeps a record for each registered boiler showing the owner, location, type, dimensions, maximum allowable working pressure, age and last inspection, and each boiler carries a department-issued registration number fixed to it at initial registration. Alongside that number, the National Board number on the nameplate traces the boiler’s construction data report. When Paul Industries scopes a repair, it records both numbers so the repair report and the next inspection report match the state’s file.

Are boilers at the Savannah River Site and other federal installations covered by the South Carolina Act?

Boilers under federal control sit outside the South Carolina Boiler Safety Act under Section 41-14-60, so they follow the federal owner’s own inspection program. Privately owned plants in the Aiken area, such as tire and industrial plants, remain under the Act or its report-filing exemptions. Paul Industries confirms which program governs each boiler before planning the repair, so the records go to the right authority.

Can a manufacturing plant's process boiler skip the state boiler program?

A boiler that is part of a manufacturing process is exempt from the detailed regulations only if a timely inspection report is filed, either a special inspector’s report or an insurer’s certification showing inspection at the right frequency. The plant therefore still has each process boiler inspected on schedule. What it avoids is the operating rule set that applies to boilers in commercial and public buildings. Paul Industries repairs process boilers to the same NBIC methods either way.

What happens if a South Carolina boiler's certificate inspection runs late?

The Act allows a grace period of two months beyond the annual or biennial interval. After that, the boiler is out of compliance, and LLR can impose a civil penalty of up to $5,000 per violation and up to $100 a day for failing to comply after written notice. When a repair outage falls near the due date, Paul Industries opens and prepares the boiler so the inspector can complete the certificate inspection in the same shutdown.

What does the $25 South Carolina boiler filing fee pay for?

The $25 fee is charged per boiler when the inspection report is filed with the LLR Boiler Safety Program, and LLR invoices the owner for it. It covers registering the report with the state, not the inspection itself, which is charged by the insurer or inspection company, and not the cost of preparing the boiler. Repair and preparation work from Paul Industries is priced separately and shown line by line.

Can a boiler keep running while a South Carolina repair waits for a planned shutdown?

That depends on the finding. Where a filed report shows noncompliance, LLR may set a date by which corrections must be made, while a finding that the boiler is unsafe must be corrected promptly, or the inspector notifies the chief boiler administrator, who may order the boiler out of operation. Paul Industries reviews the finding, proposes interim measures where they are safe, and schedules the permanent repair to close the record quickly.

What does South Carolina require when a boiler safety valve is pulled for repair?

The regulations bar work on a safety appliance while it is under pressure, and any safety valve or other appliance removed during an outage must be reinstalled and working before the boiler returns to service. A valve may never be altered to hold a pressure above the figure on the inspection report. Paul Industries replaces or repairs the valve, confirms the set pressure against the boiler’s rating and records the details for the inspector.

Can a cracked riveted boiler be patched in South Carolina?

A crack found along a longitudinal riveted lap seam takes the shell or drum out of use immediately, and South Carolina’s regulations prohibit patching it. Other defects in riveted boilers can often be repaired under the NBIC with the inspector’s agreement. For a historic or older heating boiler with a lap seam crack, Paul Industries prices a replacement boiler and the installation work that comes with it.

Does a rental boiler need its own South Carolina inspection?

Yes. A rental boiler needs the chief’s permission to enter the state, arrives with its National Board registration and its latest inspection report, and is inspected and tagged by the agency that normally inspects boilers at the site, which produces its certificate. Paul Industries connects rental boilers for repairs and changeouts, including steam and feedwater tie-ins, so the plant keeps steam while its own boiler is down.

Does a gas-fired boiler replacement need an SC DES air permit?

A boiler under 10 million Btu per hour burning only natural gas or other virgin gas fuel needs no construction permit under Regulation 61-62.1, unless another state or federal requirement applies. Larger units, oil or solid fuel units above 1.5 million Btu per hour, and fuel changes can need one, which affects the schedule. Paul Industries confirms the rating and fuel early in the replacement plan.

What does a South Carolina plant need for a 36-month internal inspection cycle on a power boiler?

The boiler must be fully attended, with continuous water treatment supervised by trained people, records of every outage and daily water analysis, and controls and safety devices that are current, calibrated and in service under codes such as NFPA 85 and ASME CSD-1. The external inspection stays annual. Paul Industries backs the case with tube condition data from repairs and with control upgrades where the existing devices fall short.

Who services boilers in South Carolina hospitals, hotels and campuses?

Paul Industries services boilers at hospitals, hotels, universities and office buildings in Columbia, Charleston, Greenville, Myrtle Beach and Rock Hill, covering seasonal startups, combustion tuning, low-water cutoff and safety valve testing, and repairs found along the way. Heating boilers in these buildings fall under the Act’s two-year inspection cycle, and service records help the inspector confirm the controls are working.

When a repair is no longer worth it, who installs boilers for South Carolina owners?

Paul Industries installs the replacement as well, supplying the new boiler or setting an owner-furnished one, with removal of the old unit, rigging, piping, fuel train, controls, startup and the National Board I-1 installation report and start-up sheets for the owner’s file. Keeping the repair diagnosis and the replacement under one contractor means the findings that justified replacement shape the new installation.

What should a South Carolina facility send to price a boiler repair?

Send the boiler make, model and type, the National Board and South Carolina numbers, the design pressure and fuel, the latest inspection report and any finding, recent alarm and trip history, water treatment logs and photos of the damage or nameplate. Paul Industries uses that to plan the diagnostic visit and returns a scope with parts, labor, testing and any welded pressure-part work shown separately.

Have a boiler finding to close in South Carolina?

Send the boiler data, its National Board and South Carolina numbers, the inspector’s finding and recent logs. Call 201-450-8280 or request a quote.