Paul Industries provides pressure vessel fabrication in South Carolina, designing, building, testing, delivering and installing ASME Section VIII vessels for tire, automotive, aerospace, chemical, pharmaceutical and food plants across the state. South Carolina’s Boiler Safety Act exempts unfired pressure vessels, so a vessel’s safety case rests on the ASME Code, the National Board, the state mechanical code, SC OSHA and the plant’s insurer rather than on a state certificate. Paul Industries builds each vessel to that full set of requirements and hands over the records every one of them asks for.

Request a quote or call 201-450-8280

Headquarters 256 Shore Drive, Kilmarnock, Virginia
State vessel program Unfired pressure vessels exempt from the Boiler Safety Act, S.C. Code 41-14-60(C)
Construction rule SC Mechanical Code 1003.1: vessels built to the ASME Code unless otherwise approved
Workplace safety SC OSHA state plan, administered by LLR
Charleston Harbor 52 feet deep (SC Ports)
Reviewed November 2026

South Carolina pressure vessel regulations: what applies to an unfired vessel

South Carolina pressure vessel regulations start from one plain rule: Section 41-14-60(C) of the Boiler Safety Act exempts all pressure vessels from that chapter, so the state’s Boiler Safety Program registers and inspects boilers but issues no certificate for an air receiver, reactor, heat exchanger shell or accumulator. That exemption does not leave the vessel unregulated; it moves the requirements to four other places, each of which a well-built vessel satisfies at once.

The first is the South Carolina Mechanical Code, the state’s edition of the International Mechanical Code, which every municipality and county must enforce. Among its pressure vessel rules, Section 1003.1 requires pressure vessels, unless otherwise approved, to be built to the ASME Boiler and Pressure Vessel Code and installed to the manufacturer’s instructions, and Section 1003.3 sends welding on pressure vessels to Part 3 of the National Board Inspection Code. The second is SC OSHA, the state plan that the Department of Labor, Licensing and Regulation runs with standards identical to federal OSHA. The third is the plant’s boiler and machinery insurer, whose inspectors examine the vessels it covers. The fourth is the owner’s own mechanical integrity program, which chemical and refrigeration plants must keep under the process safety management standard.

The routes that govern an unfired pressure vessel in South Carolina
RouteWhat it requires of the vesselRecord the owner keeps
ASME Code and National BoardDesign, materials, welding, examination and pressure test to Section VIII; nameplate and data reportManufacturer’s Data Report, National Board registration, calculations, test record
South Carolina Mechanical Code, Section 1003Vessels built to the ASME Code unless otherwise approved; installed to manufacturer’s instructions; piping approved; welding per NBIC Part 3Mechanical permit and inspection from the city or county
SC OSHA (state plan)Air receivers to OSHA 1910.169; mechanical integrity under 1910.119 for covered processesInspection and test records, relief device records
Boiler and machinery insurerPeriodic inspection of covered vessels by the insurer’s commissioned inspectorsInsurer inspection reports and recommendations
Boiler Safety ActApplies to fired vessels that meet the boiler definition; unfired vessels exemptBoiler registration and inspection reports for fired equipment

Those routes explain why pressure vessel requirements by state can look so different on paper while the vessel itself barely changes. A vessel built for a state with full registration carries a state number as well; a vessel for a South Carolina plant carries the same nameplate, the same National Board registration and the same data report, and the owner files it with the insurer and the plant’s integrity records instead of a state office. The South Carolina overview explains how those records sit alongside the other evidence a regulated site keeps.

Is there a South Carolina pressure vessel code?

South Carolina has no separate state pressure vessel code; the South Carolina pressure vessel code in practice is the ASME Boiler and Pressure Vessel Code, Section VIII, called up through the state mechanical code, OSHA standards, insurers and purchase specifications. That gives South Carolina buyers a single, national technical standard to specify, which simplifies orders for plants that also run sites in states with their own programs.

Non-ASME pressure vessels sit awkwardly in that picture. The mechanical code allows another construction only where it is approved, OSHA requires air receivers to be ASME vessels, and insurers rarely accept equipment without a data report. In practice, Paul Industries builds every vessel for a South Carolina plant to Section VIII, Division 1 or Division 2, with the National Board registration that lets it move between owners, sites and states later in its life. Design details common to all of these orders are on the pressure vessel fabrication service page.

Pressure vessel vs boiler: where South Carolina’s law draws the line

The pressure vessel vs boiler distinction decides whether a piece of equipment falls under South Carolina’s Boiler Safety Act, and the Act’s test is whether the equipment itself generates heat, from burning fuel or from electric, solar or nuclear energy, to warm a liquid or raise or superheat steam that is used elsewhere. An unfired vessel that holds pressure from a compressor, a process reaction or steam made elsewhere is a pressure vessel and sits outside the Act. The National Board’s summary of the South Carolina program treats fired pressure vessels the other way, as equipment the boiler rules reach, and the mechanical code also sends directly fired vessels to its boiler section.

How common plant equipment is classed in South Carolina
EquipmentClassState boiler programConstruction code
Compressed air and nitrogen receiversUnfired pressure vesselExemptASME Section VIII; OSHA 1910.169 for air
Steam-heated autoclaves and sterilizersUnfired pressure vesselExemptASME Section VIII, quick-actuating closure rules
Deaerators, blowdown tanks, flash tanks and condensate receiversUnfired pressure vesselExemptASME Section VIII
Shell-and-tube heat exchangers and jacketed reactorsUnfired pressure vesselExemptASME Section VIII, TEMA for exchangers
Directly fired process heaters and fired vesselsFired pressure vesselWithin the boiler rulesASME Code; mechanical code boiler section
Steam boilers and hot water boilersBoilerRegistered and inspectedASME Section I or IV

The pressure vessel vs atmospheric tank line is the other boundary a buyer meets. A tank designed for atmospheric pressure, or the few pounds per square inch an API 650 or API 620 tank may carry, is built to tank standards, while design pressures above 15 psi bring the vessel under Section VIII. Tanks on the atmospheric side of that line are covered on the tank fabrication in South Carolina page, and boilers on the fired side on the boiler repair in South Carolina page.

Who inspects pressure vessels in South Carolina?

In South Carolina, the people who inspect pressure vessels in service are the commissioned inspectors of the plant’s insurer, the owner’s own inspection staff working under a mechanical integrity program, and SC OSHA compliance officers when a workplace inspection reaches the vessel; during construction, the ASME Code places an Authorized Inspector over the fabrication. For anyone asking who inspects pressure vessels in a state without a vessel program, the answer is that the inspection still happens, but the paperwork goes to the insurer and the plant rather than to a state office.

During fabrication, the Authorized Inspector reviews the design calculations, materials, welding procedures and examination records, witnesses the pressure test and signs the Manufacturer’s Data Report before the nameplate is applied. In service, plants that refine, process chemicals or store large quantities of ammonia apply API 510 or the NBIC to their inspection intervals, and OSHA’s process safety standard requires inspection and testing of pressure vessels in covered processes to recognized engineering practice. Paul Industries builds the vessel so that each of those inspectors finds what it needs: a complete data package, accessible nozzles and manways, and thickness monitoring locations marked on the drawings.

How pressure vessel fabrication in South Carolina runs from data sheet to startup

Pressure vessel fabrication in South Carolina follows the same ASME sequence on every order, from design conditions on a data sheet to a vessel set, piped and started at the plant, with records added at each step. The table sets out that sequence and what the owner receives.

From order to startup for a South Carolina pressure vessel
StageWhat happensOwner receives
Design basisDesign pressure and temperature, minimum design metal temperature, corrosion allowance, contents, nozzle schedule, wind and seismic loads for the siteData sheet for approval
Calculations and drawingsShell, heads, nozzles, supports and lifting lugs calculated to Section VIIICalculation package and general arrangement drawing
MaterialsPlate, forgings and pipe traced to mill test reportsMaterial test reports
Welding and examinationQualified procedures and welders to Section IX; radiography or ultrasonic examination as the joint efficiency requires; heat treatment where requiredWeld map, procedure and examination records
Pressure testHydrostatic test at no less than 1.3 times MAWP adjusted for stress ratio, or pneumatic at 1.1 times under Code limits, witnessed by the Authorized InspectorTest record
Nameplate and registrationData report signed, nameplate applied, National Board registration completedManufacturer’s Data Report and National Board number
Delivery and installationShipping, setting, anchoring, piping, relief device and instrument installationInstallation and startup records

A related question from plant engineers is how often do pressure vessels need to be tested once they are in service. The ASME Code calls for the hydrostatic or pneumatic test once, at construction; later tests follow repairs, alterations, insurer recommendations or the plant’s inspection program, and are often replaced by thickness surveys and visual inspection. Paul Industries carries out shop and field testing, described on the hydrostatic testing page, whenever a repair or rerate calls for one.

Vessels for South Carolina tire, automotive and battery plants

South Carolina’s tire and automotive plants use large numbers of pressure vessels, because tire curing and vehicle production both run on compressed gases, steam and process fluids held under pressure. The state hosts Michelin’s North American headquarters in Greenville and several Michelin plants, two Bridgestone tire plants in Aiken County, a Continental tire plant in Sumter and a Giti tire plant in Richburg; BMW builds vehicles in Spartanburg, and Scout Motors’ plant at Blythewood near Columbia is designed for up to 200,000 vehicles a year.

In a tire plant, each curing press shapes the green tire with low-pressure steam or nitrogen inside a bladder, heats it with high-pressure steam and holds it with high-pressure nitrogen, so the plant runs nitrogen receivers, steam accumulators, condensate flash tanks and blowdown vessels sized to dozens of presses cycling on common headers. Those vessels see frequent pressure swings, which puts fatigue, nozzle reinforcement and weld quality at the center of the design. Automotive assembly adds compressed air receivers, paint shop process vessels and heat recovery equipment, and battery and electric vehicle component projects add solvent recovery, inert gas and cooling duties.

Autoclaves for composite curing in the Charleston region

Aerospace work in North Charleston brought very large pressure vessels into the state: the 787 aft-body site cures composite fuselage sections in autoclaves, the original one 30 feet in diameter and 75 feet long, operating at about 195 psi and above 200 F, and a second unit weighing about one million pounds that was moved half a mile into place in 2015. Autoclaves combine a large-diameter shell with a quick-actuating door, so the closure, its interlocks and its pressure indication are designed under the Code’s specific rules for quick-actuating closures. Paul Industries builds and installs autoclaves for composite, sterilization and process duties, with installation detail on the autoclave installation page.

Where South Carolina plants use pressure vessels, by region
RegionTypical plantsVessels most often ordered
Greenville, Spartanburg and the UpstateTire, automotive, supplier and textile plantsAir and nitrogen receivers, steam accumulators, flash tanks
Columbia, Blythewood and the MidlandsVehicle assembly, food, pharmaceutical and campus plantsAir receivers, heat exchangers, hot water and expansion vessels
Charleston, North Charleston and Berkeley CountyAerospace, chemical, food and port-side plantsAutoclaves, reactors, separators, receivers
Aiken, Sumter and Chester CountyTire and industrial plantsCuring utility vessels, condensate and blowdown vessels
Florence and the Pee DeePaper, food and manufacturing plantsPressure filters, flash tanks, process vessels
Rock Hill and York CountyManufacturing and food processingReceivers, jacketed vessels, heat exchangers

Chemical, pharmaceutical and food vessels across the state

Chemical, pharmaceutical and food plants in South Carolina order the widest range of vessel designs, from carbon steel separators and jacketed reactors to polished stainless process vessels. Stainless vessels for pharmaceutical and food duty add surface finish, drainability and documentation requirements on top of Section VIII, and passivation before startup is often part of the order, as described on the passivation services in South Carolina page. Heat transfer equipment for those plants, from shell-and-tube exchangers to jacketed vessels, is covered on the heat exchangers page.

Plants that hold large quantities of ammonia or other highly hazardous chemicals fall under OSHA’s process safety management standard, which SC OSHA enforces. Its mechanical integrity element requires written procedures, inspection and testing of pressure vessels to recognized engineering practice, and correction of deficiencies, so the original data report, calculations and thickness baseline from fabrication become part of the plant’s compliance file.

Air receivers under OSHA 1910.169 and the SC OSHA state plan

Air receivers in South Carolina workplaces must meet OSHA 1910.169, which SC OSHA enforces through the state plan: the receiver is built to ASME Section VIII, fitted with a drain at its lowest point, an indicating pressure gauge and spring-loaded safety valves, and installed so the drain, manholes and handholes can be reached. Receivers sit on almost every plant floor and are often bought as commodity items, so the OSHA requirements are the floor a plant should hold every receiver to.

Paul Industries sizes receivers to the compressor and demand profile, orders them with the drain, gauge and relief connections in the right places, and installs them with drains piped to an accessible point. For receivers already in service, thickness readings at the bottom head and around the drain, where condensate collects, show whether a receiver is due for replacement.

Pressure vessel shipping to South Carolina sites

Pressure vessel shipping to a South Carolina site is planned around the vessel’s diameter, length and weight, and the state’s highway, rail and port routes give options that many inland states lack. Most vessels move by truck under oversize permits; very large or heavy vessels can move by water through Charleston, where SC Ports lists a 52-foot harbor, or by rail to the Upstate through Inland Port Greer, which SC Ports opened in 2013 with daily rail service 212 miles inland, and to the Pee Dee through Inland Port Dillon.

The route shapes the design. A vessel that must fit under highway clearances may be built in sections with a field seam, which then needs field welding, examination and a field pressure test under the Code; a vessel delivered by barge can stay in one piece. Paul Industries plans the route, the lifting lugs, the saddles and the rigging at the design stage, sets the vessel on its foundation and connects it, so the shipping plan and the installation plan are the same document. Field welding of vessel seams and connections is covered on the industrial welding services in South Carolina page, and the piping that ties a new vessel in on the process piping in South Carolina page.

Wind and seismic loads on Lowcountry vessels

Tall vessels and vessels on structures in coastal South Carolina are designed for both hurricane wind and seismic loads, and the 1886 Charleston earthquake is the reason the seismic side receives real attention there. The site’s design values come from the adopted building code for the project location, and Paul Industries uses them for the skirt, anchor bolts, saddles and support steel so the vessel and its foundation are checked together.

ASME pressure vessel fabricators: what South Carolina buyers should compare

When South Carolina buyers compare ASME pressure vessel fabricators, the points that decide the outcome are the completeness of the data package, the examination and test plan, the schedule against the plant’s shutdown, and whether delivery, setting and piping are inside the same contract. Price per ton of steel tells a buyer little; a vessel that arrives without calculations or with an incomplete data report costs far more in delays than it saved.

Paul Industries quotes South Carolina vessels with the design basis, materials, examination extent, test method, documentation list and installation scope stated line by line, so the comparison with other pressure vessel fabricators is clear. It offers the routes a buyer may need: supply of the vessel alone, design-build from a process requirement, and complete installation with piping, instruments and startup.

Repairs, alterations and rerates on South Carolina vessels

Repairs and alterations to pressure vessels already in South Carolina service follow the National Board Inspection Code, with the inspector consulted before work starts, because the state mechanical code points welding on pressure vessels to NBIC Part 3 and insurers expect the same. A rerate to a higher pressure or temperature is an alteration even when no welding is done, and it is documented on the NBIC alteration report with new calculations and a new nameplate.

Paul Industries assesses the vessel with thickness readings and inspection, decides with the owner whether a repair, rerate or replacement makes sense, carries out the work, tests it and updates the records. Since the state keeps no vessel file, those NBIC reports are the vessel’s legal history, and Paul Industries delivers them to the owner’s integrity program and insurer.

Pricing a custom vessel for a South Carolina plant

The price of a custom pressure vessel for a South Carolina plant is driven by its size, design pressure and temperature, material, wall thickness, number and size of nozzles, internals and jackets, examination extent, heat treatment, surface finish, and the delivery and installation scope. Stainless steel and alloy materials, full radiography, and polished or electropolished interiors add the most; a carbon steel receiver with standard nozzles is at the other end of the range.

Schedule matters as well, because many vessels in South Carolina plants are replaced during fixed annual shutdowns, and the material lead time sets the start date. Paul Industries gives a budget range from comparable vessels once the data sheet is known, then a firm price after the design basis is agreed, with delivery and installation shown separately so the owner can compare routes.

Who fabricates pressure vessels in South Carolina?

Paul Industries fabricates pressure vessels for South Carolina plants; the company is headquartered at 256 Shore Drive, Kilmarnock, Virginia, works as an East Coast contractor and was formerly based in northern New Jersey and then Pennsylvania. It designs, builds, tests, delivers and installs ASME vessels for plants across the state and along the East Coast, in all 50 states and at plants outside the United States. Its headquarters state page covers pressure vessel fabrication in Virginia, and owners with sites in neighboring states can compare the state programs on the North Carolina and Georgia pages.

Pressure vessels from Paul Industries for South Carolina owners

Paul Industries designs, fabricates, examines, tests, registers with the National Board, delivers, sets, pipes and starts up pressure vessels for South Carolina plants, and repairs, alters and rerates vessels already in service, with a complete data package for the owner, the insurer and the plant’s integrity program. Send the data sheet or process conditions and request a quote, or call 201-450-8280.

Standards referenced: ASME Boiler and Pressure Vessel Code, Section VIII, Divisions 1 and 2 · ASME Section IX · National Board Inspection Code (NBIC) · South Carolina Boiler Safety Act, S.C. Code 41-14 · South Carolina Mechanical Code (International Mechanical Code with state modifications) · OSHA 29 CFR 1910.169 · OSHA 29 CFR 1910.119 · API 510

Frequently asked questions

Who builds pressure vessels for plants in Greenville, Spartanburg and along I-85?

Paul Industries builds pressure vessels for tire, automotive, supplier and textile plants in Greenville, Spartanburg, Greer, Duncan and the rest of the Upstate. Typical orders are compressed air and nitrogen receivers, steam accumulators, condensate flash tanks and blowdown vessels, all to ASME Section VIII with National Board registration. Paul Industries delivers, sets and pipes the vessel as well, so one contract covers the order from data sheet to startup.

Does Paul Industries fabricate vessels for North Charleston, Summerville and Berkeley County plants?

Yes. Paul Industries fabricates pressure vessels for aerospace, chemical, food and port-side plants in North Charleston, Summerville, Goose Creek and Berkeley County, from receivers and separators to autoclaves and jacketed reactors. Coastal sites add salt air corrosion and wind and seismic loads to the design, which are handled in the coatings, the material choice and the supports.

Who supplies pressure vessels to plants in Columbia, Blythewood and the Midlands?

Paul Industries supplies and installs pressure vessels for vehicle assembly, food, pharmaceutical and campus plants in Columbia, Blythewood, Lexington and the Midlands. Vessels range from air receivers and hot water expansion vessels to shell-and-tube heat exchangers and stainless process vessels, each with its data report and National Board number. Paul Industries can set and connect the vessel during a planned shutdown.

Does Paul Industries build vessels for Aiken, Graniteville and the Savannah River area?

Paul Industries builds vessels for tire and industrial plants in Aiken, Graniteville and the surrounding area, where curing presses depend on steam and nitrogen vessels sized for many presses cycling at once. Those vessels are designed for frequent pressure swings, with attention to nozzle reinforcement and weld quality. Delivery, setting and piping can be part of the same order.

Does South Carolina register or inspect unfired pressure vessels?

The South Carolina Boiler Safety Act exempts all pressure vessels from its chapter, so the state Boiler Safety Program registers and inspects boilers but issues no certificate for unfired vessels. Vessels are still built to the ASME Code under the state mechanical code, inspected by the plant’s insurer, covered by SC OSHA standards and, in process plants, by mechanical integrity programs. Paul Industries supplies the records each of those reviews needs.

Who approves standards for pressure vessels in the United States?

The ASME Boiler and Pressure Vessel Code sets construction rules, and the National Board of Boiler and Pressure Vessel Inspectors publishes the National Board Inspection Code for repairs, alterations and in-service inspection. States, cities and agencies then adopt those standards by law, as South Carolina’s mechanical code does for pressure vessels. Paul Industries builds to Section VIII and documents repairs to the NBIC.

Which agency enforces pressure vessel safety at South Carolina workplaces?

SC OSHA, the state plan run by the Department of Labor, Licensing and Regulation, enforces occupational safety standards at private workplaces and at state, county and city government workplaces in South Carolina. Its standards are identical to federal OSHA’s, including 1910.169 for air receivers and 1910.119 for process safety management. Vessels from Paul Industries arrive with the construction records those standards rely on.

When does a fired heater count as a boiler in South Carolina?

Equipment that heats water or another liquid, or makes steam, for use outside the vessel by burning fuel or using electricity, solar or nuclear energy meets the Boiler Safety Act’s boiler definition, and the National Board’s summary of the South Carolina program places fired pressure vessels within the boiler rules. The mechanical code likewise sends directly fired vessels to its boiler section. Paul Industries classifies the unit at the design stage so it is registered correctly.

Can a used pressure vessel be installed at a South Carolina plant?

A used vessel can be installed when its data report and National Board registration are available, its condition is confirmed by inspection and thickness readings, and its rating fits the new service. Without a data report, the mechanical code accepts a vessel only as an approved alternative, and insurers look for the data report before covering it. Paul Industries inspects used vessels, rerates them under the NBIC where needed and installs them with updated records.

What periodic testing do insurers and SC OSHA expect on South Carolina pressure vessels?

The ASME pressure test is made once, at construction. After that, testing follows the plant’s inspection program, the insurer’s recommendations and OSHA’s mechanical integrity rule for covered processes, which calls for inspection and testing to recognized engineering practice such as API 510 or the NBIC. Most programs rely on thickness surveys and visual inspection, with a pressure test after repairs or rerates.

How are autoclaves with quick-opening doors built for South Carolina plants?

Autoclaves are built to ASME Section VIII with the Code’s specific rules for quick-actuating closures, which require the door to be held closed until pressure is fully released and to show pressure in the vessel at the closure. Interlocks, pressure indication and the door mechanism are designed and tested as part of the vessel. Paul Industries builds and installs autoclaves for composite curing, sterilization and process work.

Do wind and seismic loads change a vessel design in the Lowcountry?

Yes. Tall vessels and vessels on structures near Charleston, Summerville and Beaufort are checked for hurricane wind and for seismic loads from the building code values for the site, which reflect the region’s history since the 1886 Charleston earthquake. Those loads size the skirt, anchor bolts, saddles and supporting steel. Paul Industries designs the vessel and its supports together.

Can a vessel built for a South Carolina plant later be moved to another state?

A vessel with an ASME data report and National Board registration can be moved, because states with their own programs accept registered vessels, subject to their installation permits and inspections. That portability is a reason to build every South Carolina vessel to Section VIII even though the state has no vessel program. Paul Industries supplies the records a new jurisdiction asks for.

What sets the delivery date of a code vessel for a South Carolina shutdown?

Material lead time usually sets the delivery date, followed by design approval, welding and examination, heat treatment where required and the pressure test. Stainless and alloy plate, forgings and special nozzles can take longer to obtain than the fabrication itself. Paul Industries works back from the shutdown date to set the approval and material dates, and plans delivery and setting into the outage.

What moves the price of a custom vessel built for a South Carolina plant?

Size, design pressure and temperature, material, wall thickness, nozzle count, internals, jackets, examination extent, heat treatment, surface finish and the installation scope move the price most. Delivery method matters for very large vessels, and field seams add field welding and testing. Paul Industries prices the vessel and its delivery and installation separately, so the owner can choose supply only or a complete installed vessel.

Can Paul Industries set and pipe a vessel as well as build it?

Yes. Paul Industries offers supply of the vessel alone, design-build from process requirements, and complete installation, including rigging, setting, anchoring, piping, relief devices, instruments, insulation and startup. Keeping fabrication and installation under one contract means nozzle orientations, supports and lifting points are designed around the way the vessel will be set and connected at the South Carolina site.

Why do tire plant vessels need fatigue checks?

Tire curing presses cycle steam and nitrogen many times an hour, so the receivers, accumulators and headers that feed them see repeated pressure swings rather than steady pressure. Repeated cycling can start cracks at nozzles and weld toes over time, so the design checks fatigue where the Code requires it, and weld profiles and examination are chosen to suit. Paul Industries designs these vessels for the press cycle the plant actually runs.

What should a South Carolina plant send to start a vessel order?

Send the process data sheet or design conditions: contents, design pressure and temperature, minimum design metal temperature, volume or dimensions, material preference, corrosion allowance, nozzle list, supports, site location for wind and seismic loads, and the target date. Photos and drawings of the existing vessel help for replacements. Paul Industries returns a budget range, then a firm price after the design basis is agreed.

Ordering a pressure vessel for a South Carolina plant?

Send the design conditions, contents, size, nozzle list and target date. Call 201-450-8280 or request a quote.