Paul Industries designs, pipes, fills, tests and services data center liquid cooling in Maine, including coolant distribution units, cold plate loops, rear door heat exchangers, immersion tanks and the warm-water facility loops and dry coolers that carry their heat outdoors. Maine’s air stays cool enough for a warm-water loop to reject heat without a chiller for more than nine hours in ten, and the state’s long heating season gives that heat somewhere useful to go. From its headquarters at 256 Shore Drive in Kilmarnock, Virginia, Paul Industries takes liquid cooling work across Maine, New England and all 50 states.

Request a quote or call 201-450-8280

Headquarters 256 Shore Drive, Kilmarnock, Virginia
Dry cooler weather Air at or below 74.6 F for 93% of Portland hours (2021-2025)
Coldest hour -28 F at Caribou, -17 F at Bangor, -14 F at Portland (2021-2025)
Hydronic test 1.5 x design pressure, 100 psi minimum, 15 minutes (2021 IMC 1208.1)
Heating season Portland monthly mean below 41 F from November through March
Reviewed November 2026

Why data center liquid cooling in Maine favors warm water

Data center liquid cooling in Maine favors warm water because a facility loop supplied at about 80 to 90 degrees Fahrenheit can reject its heat through dry coolers for roughly 80 to 95 percent of the hours in a typical year, with no compressor running. Cold plates and immersion fluids accept far warmer coolant than air-cooled servers accept air, so the cold Maine climate turns into almost continuous free cooling once the loop temperature is set high enough.

The ASHRAE liquid cooling classes, explained with the hardware on the national data center liquid cooling page, name the upper limit of facility water supply a server accepts: W17 at about 63 degrees, W27 at about 81, W32 at about 90 and W40 at 104. In Maine the choice of class matters more than the choice of dry cooler, because it decides whether the room needs a chiller at all.

This page covers what changes in Maine: the dry cooler hours each class earns at Portland, Bangor and Caribou, freeze protection for loops that see minus 28 degree nights, condensation in a coastal summer, reuse of rack heat in a heating climate, and testing to the 2021 International Mechanical Code that Maine adopted.

Where does dense computing run in Maine?

Dense computing in Maine runs today in university, enterprise and research rooms rather than hyperscale halls, and at least one large proposal for new capacity, at Loring, is built around immersion cooling. The University of Maine System’s Penobscot high performance computing cluster, which includes an NVIDIA DGX A100 node with eight A100 accelerators, runs in the system’s main data center in Orono, and the system keeps backup storage at its Portland campus data center.

The new proposals point the same way. A developer announced in October 2025 a data center at the Loring Commerce Centre in Limestone that would immerse its servers in dielectric fluid, start at 5 to 6 megawatts with a stated ceiling of 50, and send recovered heat as hot water to other uses in the same building, such as crop dehydration; listings still show it as planned. The broader Maine market, including the redevelopment proposed at the former Androscoggin Mill in Jay, is covered on the data center cooling in Maine page.

For most Maine owners the practical question is smaller: how to bring a few racks of 30 to 100 kilowatts or more into a room built for air, inside a hospital, office, campus or plant. Those projects drive most liquid cooling work in the state, and they share the same climate advantages as the large proposals.

Dry cooler hours for each liquid cooling class in Maine

Dry cooler hours for a Maine liquid loop depend on the facility water class and on the approach the dry cooler is sized for, and with a 15 degree approach a W32 loop runs compressor-free for about 93 to 95 percent of the year at all three major airports. The table uses five years of hourly National Weather Service observations, 2021 through 2025.

Share of hours a dry cooler alone can meet each facility water class (15 F approach)
Class and upper supplyOutdoor air neededPortland (PWM)Bangor (BGR)Caribou (CAR)
W17, about 63 F48 F or lower49%51%56%
W27, about 81 F65.6 F or lower80%80%84%
W32, about 90 F74.6 F or lower93%93%95%
W40, 104 F89 F or lower99.8%99.8%99.9%

The hours a W32 loop cannot cover on dry air alone are few, about 584 a year at Portland, 617 at Bangor and 465 at Caribou, and they fall on summer afternoons. Owners cover them in one of three ways: an adiabatic dry cooler that wets its coils on those afternoons, a trim chiller or a tie to the building’s existing chilled water through a plate exchanger, or a slightly larger dry cooler with a closer approach. On a W40 loop, a Maine dry cooler carries the load essentially all year.

The W17 row shows why rooms that tie liquid cooling to an old 45 degree chilled water plant gain little. At that temperature the loop behaves like an air-cooled room and needs mechanical cooling half the year, so Paul Industries plans new liquid-cooled rows around their own warm-water loop wherever the servers allow it.

Can liquid cooling freeze in a Maine winter?

Liquid cooling can freeze in a Maine winter wherever water or weak glycol sits in outdoor coils, exposed piping or an unheated room, because the 2021 to 2025 record includes hourly lows of minus 14 degrees at Portland, minus 17 at Bangor and minus 28 at Caribou. The rack-side loop indoors is safe while the building is heated; the risk lies in the facility loop that runs to the dry coolers and in any piping that crosses a cold space.

The usual Maine arrangement separates the two. Inside, the technology cooling loop runs treated water or a dilute glycol chosen for the cold plates and the CDU manufacturer’s chemistry. Outside, the facility loop carries propylene glycol at a strength set by the site’s coldest hour, and a plate exchanger in heated space keeps the two apart. Published tables put propylene glycol’s freezing point near 7 degrees at about 30 percent by volume, minus 8 at 40 percent and minus 29 at 50 percent.

Fluid choices for each loop in a Maine liquid cooling system
LoopTypical fluidMaine freeze exposureProtection
Technology cooling loop (rack to CDU)Treated water or dilute propylene glycol per the cold plate supplierNone while the room is heatedRoom heat, layup procedure if the room ever goes cold
Facility loop, indoor sectionWater, isolated by a plate exchangerMechanical rooms on outside walls, shaftsInsulation, heat tracing on any run through unheated space
Facility loop to dry coolers, southern and central MaineAbout 40% propylene glycolHourly lows near minus 14 to minus 17 FConcentration checked each autumn; low-limit control on leaving fluid
Facility loop to dry coolers, Aroostook CountyAbout 50% propylene glycolHourly lows near minus 28 FHigher pump head allowed for; equipment raised above drifting snow
Immersion tank fluidDielectric hydrocarbon or synthetic fluidViscosity rises sharply in cold storage or transportFluid delivered and stored warm; tanks filled inside heated space

Every increase in glycol strength costs heat transfer and adds pump head, which is why the outdoor loop is kept as short as practical and the indoor water loop does most of the distribution. Paul Industries sizes the plate exchanger, pumps and dry coolers on the actual glycol mix, checks concentration with a refractometer at fill, and sets a leaving-fluid low limit so a calm, cold night never drives the loop toward slush.

Condensation and dew point in a Maine summer

Condensation on cold plates and manifolds in Maine is a summer risk, since Portland’s July dew point averaged about 62 degrees in the 2021 to 2025 record and reached 65 degrees or higher for about 763 hours a year. Any liquid-cooled surface below the room’s dew point will sweat, and water on a server board is as damaging as a leak.

Warm-water classes avoid the problem by design: a W27 or W32 loop supplies coolant well above any Maine room dew point. The risk returns when a liquid row is fed from building chilled water at 45 to 55 degrees, or when a rear door heat exchanger runs cold to help the rest of the room. In those cases the CDU or the control system holds supply temperature a few degrees above the measured room dew point, and the room’s humidity is managed by the air system. Bangor and Caribou see fewer humid hours, about 625 and 379 a year at or above a 65 degree dew point, but the same control logic applies statewide.

Data center heat reuse in a Maine heating climate

Data center heat reuse suits Maine because a liquid-cooled room produces steady warm water all year in a state where buildings need heat for most of it, with Portland’s monthly mean temperature below 41 degrees from November through March. Almost all the electrical power a rack draws leaves as heat, and liquid cooling captures that heat in water at a usable temperature instead of spreading it through room air.

Return water from a W32 or W40 loop typically comes back at roughly 100 to 120 degrees Fahrenheit, which is warm enough for some uses directly and needs a heat pump boost for others. The Loring proposal’s plan to send recovered heat to crop drying in the same building is one Maine example of direct use, and public comment submitted to the Maine Data Center Advisory Council has urged data center waste heat recovery for district heating and greenhouses.

Where heat from a Maine liquid-cooled room can go
DestinationWater temperature it needsFit with liquid cooling returnMaine notes
Ventilation air preheatAny temperature above outdoor airDirect, through a coil in the outdoor air streamUseful for months each year; glycol coil protects against freezing
Radiant floors and snow meltingRoughly 80 to 110 FDirect from W32 and W40 loopsLoading docks, entrances and walkways in snow season
Low-temperature space heat with fan coilsRoughly 100 to 120 FDirect on the warmest loops, boosted otherwiseWorks best in buildings designed or renovated for low supply temperatures
Crop drying and greenhousesVaries by processDirect or boostedProposed at Loring; suits agricultural regions of Aroostook County
District or campus heatingOften 140 F or higherHeat pump boost neededNeeds a heat customer and piping route; larger capital step

Two points of Maine law touch a heat recovery loop. The boiler and pressure vessel chapter, 32 M.R.S. Chapter 131, exempts hot water heating boilers except those in schoolhouses, and it exempts water-filled vessels with only an air cushion, such as expansion tanks, up to 300 psi design pressure and 210 degrees. A heat recovery system that adds a fired boiler for backup in a school, or a vessel outside those limits, falls under the chapter’s registration and inspection rules, so Paul Industries checks every vessel on the schedule against the exemptions before equipment is ordered.

Floor, power and piping for CDUs in Maine rooms

A coolant distribution unit in a Maine room needs floor capacity for a heavy, water-filled cabinet, two power feeds with pumps on UPS, connection to the facility loop through valves that let it be serviced without draining the row, and a route for pipe that avoids exterior walls and unheated spaces. Rooms in older Maine buildings often lack one of the four, so the survey checks all of them before a CDU model is chosen.

Inside the room, Paul Industries runs stainless or copper row headers overhead or under the floor, fits isolation and balancing valves at each rack manifold, installs filtration sized to the cold plate supplier’s requirement, and adds leak detection cable under every manifold and along every header joint. Pipe is pressure tested before it is insulated, flushed until filters stay clean, filled with the specified coolant and only then connected to racks. Rear door heat exchangers on existing racks follow the same sequence on a smaller scale. Every valve, sensor and manifold is tagged to match the drawings, so the owner’s staff can isolate a single rack in the middle of a night shift without guessing which handle to turn.

The welding and joining behind that work is described under industrial welding services in Maine, and the facility-side headers and plate exchangers follow process piping in Maine.

Immersion cooling in Maine rooms and warehouses

Immersion cooling places servers directly in tanks of dielectric fluid, which removes fans and rack-level air paths and returns heat to a facility loop through a heat exchanger on each tank or tank group. The Loring proposal in Limestone uses this approach, and smaller immersion deployments fit into Maine warehouse and industrial space where floor area is available and ceiling height is less important than for air-cooled halls.

Immersion brings its own building questions. Filled tanks are heavy and spread their load differently from racks, so slab capacity is checked. Fluid arrives in drums or totes and has to be stored and handled above its cold-weather viscosity limit, which in a Maine winter means heated receiving and storage. Tank exchangers connect to the same warm-water facility loop and dry coolers described above, and the loop usually runs warmer than a cold plate loop, which adds dry cooler hours and makes heat reuse easier. More detail on tank layouts is on the data center immersion cooling page.

Adding the first liquid-cooled row while a Maine room stays live

Adding the first liquid-cooled row to an operating Maine room works best as a sequence of short, reversible steps, each finished and tested before the next one touches live equipment. The sequence below is the one Paul Industries follows in rooms that must stay online throughout.

The survey comes first: floor loading, power capacity for the CDU, available chilled water or a route to the roof, and the room’s current temperature and dew point trends. Facility piping and the dry cooler connection are then built and tested up to isolation valves at the edge of the room, so most of the welding, pressure testing and flushing happens away from running servers. Inside the room, the CDU is set and its row headers installed during planned windows, with hot work under the owner’s permit system and leak detection installed before any coolant arrives.

Racks are connected one at a time, each on its own manifold valves, with flow and temperature checked against the server supplier’s requirements before the next rack goes live. Later rows reuse the CDU capacity and facility connections sized for growth on the first phase, which is why the first row carries most of the infrastructure cost. In Maine, outdoor work on dry cooler pads and roof penetrations is scheduled for frost-free months, while indoor phases continue through the winter.

Testing a Maine liquid loop to the 2021 IMC

Testing a Maine liquid loop starts with the 2021 International Mechanical Code, adopted into Maine’s uniform building and energy code effective April 7, 2025, which requires hydronic piping to be tested hydrostatically at one and one-half times its maximum design pressure, never less than 100 psi, for at least 15 minutes. That rule applies to the facility piping and headers; rack manifolds, quick disconnects and CDU internals carry the manufacturer’s own pressure limits and are isolated or tested to those limits.

Maine weather adds a practical constraint. A hydrostatic test in an unheated shell or on a roof in January can freeze, so tests on outdoor and unconditioned sections are scheduled for warm weather, run with temporary heat, or drained immediately after acceptance. Flushing follows the test, with water circulated through temporary bypasses until strainer and filter checks stay clean, before any server connects. Startup, sequence testing and turnover records are covered on the data center commissioning in Maine page.

Liquid cooling energy on Maine power prices

Liquid cooling saves energy in Maine mainly by removing compressor hours and shrinking fan power, and with Maine commercial power averaging 22.83 cents per kilowatt-hour in 2026, every 10 kilowatts of continuous load removed saves about 87,600 kilowatt-hours and roughly $20,000 a year. The national average over the same months was 14.04 cents (EIA, January through August 2026), so the same savings are worth about 63 percent more here.

On a warm-water loop the remaining cooling energy is CDU pumps and dry cooler fans, and both scale with flow and speed. Variable speed drives on both, a facility loop sized for low pressure drop, and controls that let dry cooler fans slow down through the long Maine winter keep that energy low. Paul Industries estimates the yearly cooling energy on the site’s own tariff before the loop temperature and equipment are fixed.

What does data center liquid cooling in Maine cost?

The cost of data center liquid cooling in Maine is driven by the number and density of liquid-cooled racks, the choice of cold plates, rear doors or immersion, the CDU capacity and redundancy, the length of facility piping to the heat rejection, and the winter and heat reuse features the site needs. A first rack row in an existing room costs more per rack than later rows, because the CDU, facility connections and dry coolers are sized for growth.

Owners can estimate running cost with the energy figures above; installed cost is priced from the scope. To price a project, send rack counts and densities, server cooling specifications with the facility water class, floor plans and structural data, existing chilled water details, the route to the roof or pad, and any heat reuse ideas. Paul Industries returns a priced scope with equipment, piping, testing and fluid shown separately.

Who installs data center liquid cooling in Maine?

Paul Industries installs data center liquid cooling in Maine, designing, supplying, piping, filling, testing and maintaining CDUs, cold plate loops, rear door heat exchangers, immersion tank connections, facility loops and dry coolers for university, enterprise, colocation and industrial rooms across the state. Paul Industries is headquartered at 256 Shore Drive, Kilmarnock, Virginia, and its data center liquid cooling in Virginia page covers the headquarters state.

Owners choose supply-only equipment packages, design-build of the whole liquid cooling system, or complete installation to their engineer’s design. Related Maine work is grouped under data center mechanical contractors in Maine and the state overview at Maine; regional context is on the New England page and on data center liquid cooling in Massachusetts. Research rooms are a frequent fit, and research labs and universities covers that sector.

Paul Industries on Maine liquid-cooled rows

Paul Industries builds Maine liquid cooling around the climate: warm-water loops that run on dry coolers for nearly the whole year, glycol strength matched to the site’s coldest hour, dew point control for coastal summers, tested and flushed piping, and a plan for the heat. Send rack densities, server specifications and drawings, and request a quote or call 201-450-8280.

Standards referenced: ASHRAE TC 9.9 liquid cooling (W) classes · Maine Uniform Building and Energy Code (2021 IMC) · 2021 International Mechanical Code Section 1208.1 · 32 M.R.S. Chapter 131 (Maine boiler and pressure vessel law), Section 15102 · ASCE 7-16

Frequently asked questions

Who provides liquid cooling for data centers in Orono and Bangor?

Paul Industries provides liquid cooling for computing rooms in Orono, Bangor and the Penobscot Valley, from rear door heat exchangers on existing racks to cold plate rows with their own CDUs and dry coolers. Bangor’s airport averaged about 57 hours a year at or below zero across 2021 to 2025, so facility loops carry propylene glycol near 40 percent and outdoor piping is kept short.

Can Paul Industries add liquid-cooled racks to a data room in Portland or South Portland?

Paul Industries adds liquid-cooled racks to rooms in Portland, South Portland and the rest of Greater Portland, including rooms inside offices, hospitals and campus buildings. The work usually starts with a CDU and a warm-water loop for a first row, with dry coolers on the roof and a plate exchanger tie to existing chilled water for the summer afternoons a W32 loop cannot cover on dry air alone.

Who handles immersion or cold plate cooling in Aroostook County?

Paul Industries handles immersion and cold plate cooling projects in Presque Isle, Caribou, Limestone and the rest of Aroostook County. Caribou’s record low of about minus 28 degrees calls for facility loops near 50 percent propylene glycol, heated storage for immersion fluid in winter and equipment raised above drifting snow. The payoff is the state’s longest dry cooler season, about 95 percent of hours for a W32 loop.

Who installs liquid-cooled racks for Midcoast employers around Brunswick and Bath?

Paul Industries pipes liquid cooling in Brunswick, Bath and Midcoast towns for enterprise, industrial and institutional computing rooms. Coastal sites add salt air, so dry cooler coils are specified with protective coatings and outdoor piping supports are corrosion resistant. Brunswick adopted a 180-day moratorium in June 2026 on data centers with a demand of 1 megawatt or more, so Paul Industries reviews the town’s current rules with the owner before design starts.

Can liquid cooling freeze in a Maine room that loses heat during an outage?

A rack-side loop of plain treated water can freeze if a Maine room loses heat for long enough in a deep cold spell, although running servers keep the room warm while they have power. Owners protect against that case with generator-backed heat for the room, a layup procedure that drains or protects idle loops, or a dilute glycol in the technology loop where the cold plate supplier allows it.

Which liquid cooling class should a new Maine room target?

A new Maine room should target W32 or warmer where the servers allow it, because a dry cooler alone meets a W32 loop for about 93 to 95 percent of hours at Portland, Bangor and Caribou. W27 drops that to about 80 to 84 percent. W17 loops behave like chilled water rooms and need mechanical cooling for about half the year, so they make sense only where the hardware requires them.

Does a Maine liquid-cooled room need a chiller at all?

A Maine room on a W32 or W40 loop can often run without a dedicated chiller, covering the few hundred hot hours a year with adiabatic dry coolers, an oversized dry cooler or a plate exchanger tie to existing building chilled water. Rooms on W17 or W27 loops, or rooms that keep many air-cooled racks, still need mechanical cooling for part of the year, and the plant design follows that mix.

Can data center waste heat recovery heat a Maine building?

Return water from a W32 or W40 cold plate loop is warm enough for ventilation air preheat, radiant floors, snow melting and some low-temperature heating systems directly. Conventional heating systems designed for 160 to 180 degree water need a heat pump boost. Paul Industries matches the loop’s return temperature to the building’s heating design and shows the heat recovered month by month against Maine’s heating season.

Does Maine's boiler law apply to a data center heat recovery loop?

Most heat recovery loops sit outside Maine’s boiler and pressure vessel chapter, because 32 M.R.S. Section 15102 exempts hot water heating boilers outside schoolhouses and water-filled vessels with an air cushion up to 300 psi and 210 degrees. A backup boiler in a school, or a vessel beyond those limits, must be registered and inspected under the chapter, so every vessel on the project is checked before it is ordered.

How is a new liquid cooling loop pressure tested in Maine?

Facility piping for a liquid cooling loop in Maine is tested under the 2021 International Mechanical Code at one and one-half times the maximum design pressure, at least 100 psi, held for at least 15 minutes. Rack manifolds, hoses and quick disconnects are tested to their manufacturer’s limits and isolated from the higher test. In winter, outdoor sections are tested with temporary heat or drained immediately after acceptance.

Can rear door heat exchangers run on a Maine building's existing chilled water?

Rear door heat exchangers can run on existing chilled water through a CDU or a mixing station that holds the door supply above the room dew point, which in a Portland July often sits in the low to mid 60s. Running doors directly on 45 degree water risks condensation. Paul Industries checks the plant’s spare capacity, adds the CDU and controls, and sets the supply temperature from measured dew point.

What does data center liquid cooling cost to run on Maine power?

On a warm-water loop the running cost is mainly CDU pumps and dry cooler fans, priced at Maine’s 2026 commercial average of 22.83 cents per kilowatt-hour. Every 10 kilowatts of continuous pump and fan load costs about $20,000 a year, so variable speed drives, low pressure drop piping and fan control through the winter are worth designing in from the start. Compressor energy is avoided for most of the year.

Who provides liquid cooling for data centers across Maine?

Paul Industries provides liquid cooling for data centers across Maine, from York County to Aroostook County, covering design, equipment supply, piping, filling, testing and maintenance of CDUs, cold plate loops, rear doors, immersion tank connections and dry coolers. The company is headquartered at 256 Shore Drive, Kilmarnock, Virginia. Call 201-450-8280 or request a quote.

Can a Maine data center run liquid cooling without water use at the cooling plant?

A Maine liquid-cooled room can run with no continuous water use by pairing a closed facility loop with dry coolers, which the climate supports for most of the year. Data center cooling without water still needs the first fill and occasional top-ups of glycol mix, and adiabatic units add water only on the hottest afternoons. That design suits towns where water use is part of the approval discussion.

How should a Maine liquid loop be laid up if a room sits idle in winter?

A Maine liquid loop in a room that will sit unheated should be drained and blown down, or filled with propylene glycol at a strength that protects against the site’s coldest hour, before heat is cut. CDU manufacturer instructions govern the rack-side loop. On restart the loop is refilled, vented, checked for leaks and run on filtration before servers connect again.

Which contract routes cover liquid cooling equipment in Maine?

Paul Industries offers supply-only packages of CDUs, manifolds, rear doors and dry coolers with submittals and startup; design-build of the full liquid cooling system, from loop temperature selection to turnover; and complete installation to an owner’s engineered design. Maintenance after turnover covers coolant testing, filter changes, glycol checks each autumn and leak detection checks.

What should a Maine owner gather before asking for a liquid cooling price?

Gather rack counts and densities, server cooling specifications including the facility water class, floor plans and structural data, existing chilled water plant details, the route and distance to the roof or pad, power available for CDUs, and any heat reuse ideas. Photos of the room and roof help. Paul Industries uses the package to scope the loop and price equipment, piping and testing separately.

Bringing liquid-cooled racks into a Maine data room?

Send rack densities, server cooling specifications, floor plans and roof details. Call 201-450-8280 or request a quote.