Paul Industries designs, fabricates and installs process piping in Tennessee for chemical, battery, metals, food, distilling, pharmaceutical and power plants, to ASME B31.3 for process lines and B31.1 for steam and boiler piping. The work runs from line lists and stress checks through spool fabrication, installation, tie-ins during planned outages, examination, pressure testing and turnover records. Paul Industries is headquartered at 256 Shore Drive in Kilmarnock, Virginia, and takes piping work across Tennessee, from Memphis to the Tri-Cities.

Request a quote or call 201-450-8280

Headquarters 256 Shore Drive, Kilmarnock, Virginia
Boiler piping B31.1 to the first or second stop valve (Rule 0800-03-03-.03)
Contract license Required at $25,000 and up (Board for Licensing Contractors)
Building codes 2021 IMC and IPC adopted April 17, 2025
Air programs TDEC plus Davidson, Hamilton, Knox and Shelby counties
Reviewed November 2026

Where process piping in Tennessee runs today

Process piping in Tennessee runs through a broad industrial base: the state’s Department of Economic and Community Development counts more than 900 automotive companies employing over 144,700 Tennesseans, more than 520 chemical companies and more than 870 food and beverage companies. Those figures describe industrial plants in Tennessee that move solvents, slurries, steam, chilled water, compressed gases and food products through welded and flanged pipe every day. The plants and projects named here are market facts only.

Tennessee industries and the piping systems they run
Industry and regionTypical pipingGoverning code and focus
Chemicals, Kingsport and the Tri-CitiesProcess lines for intermediates and solvents, steam and condensate, cooling water, flare and vent headersB31.3 Normal and Category M service, B31.1 at the boilers; alloy selection and NDE extent
Battery cells and vehicles, Spring Hill, Middle Tennessee and ChattanoogaSolvent recovery, slurry, nitrogen, compressed air, process cooling, dry-room utilitiesCleanliness, leak tightness, moisture control; Ultium Cells is retooling Spring Hill for LMR cells through 2028
Metals processing, ClarksvilleAcid, slurry and process water lines for new nonferrous productionLined and alloy piping, abrasion allowances
Nuclear fuel and research, Oak RidgeProcess gas, cooling water and utility piping at private facilities such as the new fuel plants at the Horizon CenterTraceability and quality program flow-downs from the owner
Distilling, Lynchburg, Tullahoma and Middle TennesseeMash, beer, low and high wines, spirit transfer, steam to cookers and stills, CIPSanitary stainless for product, flammable liquid rules for high-proof spirit
Food and beverage, Memphis, Clarksville and statewideProduct, CIP, glycol, ammonia refrigeration, steam3-A and ASME BPE sanitary details, B31.5 refrigeration practice

What is process piping used for in a Tennessee plant?

Process piping is used for moving the materials a plant makes or consumes between its equipment: raw materials into reactors and tanks, intermediates between steps, finished product to packaging or storage, and the utilities that run the process, such as steam, chilled water, nitrogen and compressed air. ASME B31.3 covers that piping inside the plant boundary, from chemical plants to food and battery plants, while B31.1 covers power piping such as boiler steam and feedwater.

What is process piping installation at an operating plant?

Installation at an operating plant is a sequence, and Paul Industries starts from the process and instrument diagrams and line list, sets line classes for each fluid, checks flexibility and support loads, fabricates spools off site from isometric drawings, installs and supports them, makes the tie-ins, examines the welds, tests the system, cleans or flushes it, and hands over a turnover package. The national method is described on the process piping page; this page covers how that work fits Tennessee rules and plants.

How Tennessee’s 2021 codes separate plant piping from building systems

Tennessee’s building codes separate plant piping from building systems by scope: the State Fire Marshal’s Office adopted the 2021 International Mechanical, Plumbing and Fuel Gas Codes effective April 17, 2025, and those codes govern building services such as potable water, drainage, fuel gas and HVAC, while process piping inside a plant follows the ASME B31 codes the owner specifies. Large cities and counties, including Memphis, Nashville and Davidson County, Knoxville, Chattanooga, Clarksville, Kingsport, Murfreesboro, Jackson, Spring Hill and Oak Ridge, run their own plans review and adopt their own code editions.

Process piping vs plumbing at the connection points

The boundary between plant piping and building plumbing matters at every connection between the two. Potable water feeding a process skid passes through backflow prevention under the plumbing code before it becomes process water; fuel gas to a boiler burner follows the fuel gas code up to the equipment; and a process drain becomes building drainage at a defined point, often after neutralization. Paul Industries draws those boundaries on the drawings at the start, so plan reviewers, inspectors and the owner’s engineers agree on which code governs each line.

Boiler external piping: where B31.1 and the state boiler rules meet

Boiler external piping in Tennessee is governed by the Board of Boiler Rules as well as by ASME: Rule 0800-03-03-.03(4) places power piping from a power boiler to the first stop valve of a single boiler, or to the second stop valve in a battery of two or more boilers, under ASME Section I, with the valves and piping designed, fabricated, installed and tested to ASME B31.1. Welded piping in that zone carries ASME code certification, stamping and the data report forms that go to the owner and the Chief Inspector.

Beyond the second stop valve, steam headers and distribution follow B31.1 or B31.3 as the owner’s specification sets, and Tennessee’s rules add a relief valve on the low-pressure side of any reducing station whose downstream piping cannot withstand full boiler pressure, sized so a reducing valve stuck wide open, or an open bypass, cannot overpressure the low side, which also carries its own gauge (Rule .04(4)). Paul Industries designs steam and condensate systems to those boundaries and coordinates with boiler repair in Tennessee when piping and boiler work share an outage.

Piping for Tennessee battery cell and vehicle plants

Piping for battery cell plants differs from ordinary manufacturing utilities because moisture, particles and solvent leaks all affect cell quality and safety. Electrode coating lines commonly use a solvent that is recovered from dryer exhaust and returned through condensers, columns and storage tanks, so solvent recovery piping is a closed loop with tight joints, compatible gaskets and documented leak testing. Slurry lines carry abrasive, shear-sensitive mixtures and need smooth bores, long-radius turns and flushing connections. Dry rooms depend on dehumidification systems whose chilled water, glycol and regeneration heat piping runs around the clock, and formation and aging areas need process cooling with steady temperatures.

Tennessee’s economic development department reports more than $16.2 billion of capital investment in electric vehicles since 2017 and ranks the state first in the Southeast for EV manufacturing employment and investment, figures that explain the volume of utility and process piping in Middle Tennessee. Retooling an operating plant, as Ultium Cells is doing at Spring Hill, means new piping goes into buildings that already hold live systems. Paul Industries prefabricates spools to field measurements, tests them before they reach the plant, and installs them in phases so lines that keep running are never disturbed longer than their tie-in window.

Sanitary and high-purity piping in Tennessee food, distilling and life science plants

Sanitary and high-purity piping in Tennessee serves food, beverage and distilling plants, and a growing life science base: the state reports more than 2,900 healthcare and life sciences companies, and Nashville is home to a contract manufacturer of sterile injectable medicines that has been expanding its site. Product lines in those plants are stainless tubing with orbital welds, sanitary clamp or welded joints, sloped to drain, free of dead legs, and documented with weld logs and borescope records. Water for injection and purified water loops follow ASME BPE and the plant’s validation program.

Food and spirits plants work to 3-A sanitary practice and their own hygiene programs rather than pharmaceutical validation, so the specification sets finish, slope and cleanability without the full qualification package. Paul Industries builds both levels and matches the documentation to the plant’s regulator. Detailed sanitary scope for the state is on the sanitary process piping in Tennessee page.

Pipe racks, supports and routing inside existing Tennessee plants

Pipe racks and supports decide whether new piping fits into an existing Tennessee plant without overloading old steel or blocking maintenance access. Paul Industries surveys existing racks before routing new lines, checks the added load against the rack’s capacity, and designs new rack sections, trapeze supports, guides and anchors where the existing steel is full. Hot lines get guides and expansion loops sized from the flexibility analysis, and lines crossing roadways or crane paths get clearances agreed with the plant.

Older plants in the Tri-Cities, Chattanooga and Memphis often carry decades of abandoned lines on their racks. Removing dead piping during a project frees space for new lines and removes corrosion and leak risks, and Paul Industries prices that demolition alongside the new work so the owner can decide with both costs in view.

Steam and condensate systems beyond the boiler

Steam and condensate piping beyond the boiler’s stop valves is where many Tennessee plants lose energy and suffer water hammer. Distilleries, food plants and chemical plants run long steam mains to cookers, stills, jackets and heat exchangers, and each low point and change in elevation needs a drip leg and trap station so condensate never collects in front of a slug of steam. Condensate returns are sized for flash steam as well as liquid, pitched toward receivers, and routed to avoid lifts that trap water. Paul Industries designs steam mains with drip legs at regular intervals and at every rise, installs trap stations with isolation and test valves, and returns condensate to the boiler room so its heat and treated water are recovered rather than dumped to drain. Upgrading a neglected condensate system often pays back in fuel and water treatment savings before the next boiler inspection comes around.

Process piping requirements by fluid service

Process piping requirements under ASME B31.3 depend on the fluid service category, which the owner assigns from the fluid’s hazard, pressure and temperature, and which sets the examination, testing and design rules for each line. Paul Industries works through the line list with the owner’s engineers to confirm each category before fabrication, because a late change from Normal to Category M service changes the welding, examination and test plan.

B31.3 fluid service categories and what each means on a Tennessee job
Fluid serviceTypical Tennessee linesExamination and testing
Category DCooling water, low-pressure air and nonflammable, nontoxic utilities at or below 150 psig and 366 FVisual examination; initial service leak test permitted instead of hydrostatic
NormalMost process, solvent and utility lines in chemical, battery and food plantsRandom radiography or ultrasonic on 5 percent of circumferential welds; hydrostatic test at 1.5 times design pressure, adjusted for temperature
Category MHighly toxic chemicals where a small release is dangerousAdded examination, restrictions on joints and components, sensitive leak test
High PressureHydrogen, high-pressure gas and hydraulic service in the owner’s designated linesChapter IX rules, 100 percent volumetric examination
High PurityPharmaceutical, biotech and battery solvent lines specified to ASME BPEChapter X rules, orbital welding and borescope inspection, documented surface finish

Pneumatic testing at 1.1 times design pressure replaces hydrostatic testing only where water would damage the line or the process, and it calls for a written safety plan and exclusion zone. Stainless lines tested with water get low-chloride water and are drained and dried promptly to protect against pitting.

Contractor licensing and permits on Tennessee piping projects

Contractor licensing on Tennessee piping projects is set by the Board for Licensing Contractors, which requires a license before contracting, bidding or negotiating a price on any project of $25,000 or more, whether as prime contractor, as a mechanical or plumbing trade contractor whose portion reaches $25,000, or as a construction manager. The license carries a classification, such as industrial building (BC-C) or the mechanical classifications CMC, CMC-A for plumbing and CMC-C for HVAC, and a monetary limit for each project, calculated from the firm’s working capital and net worth with a 10 percent tolerance.

Owners asking about licensing in Tennessee are really asking which of those requirements reaches their job, and the answer depends on the contract value, the scope and whether the work includes building plumbing or HVAC. New process buildings and additions are permitted by whichever authority reviews plans at the site, either the state or one of the exempt municipal and county code departments. Paul Industries confirms permit and contract requirements during estimating, so the owner’s procurement team sees them before award.

Air permits and piping changes

Air permits reach piping when a change alters emissions: a new solvent line feeding a coating oven, a vent header tied to a new emission point, or a bypass around a control device. TDEC’s Division of Air Pollution Control issues construction and operating permits directly in 91 counties, while Davidson, Hamilton, Knox and Shelby counties run their own air pollution control programs. Paul Industries flags piping changes that touch permitted equipment during design, so the plant’s environmental staff can file before construction instead of after.

Process piping specification: what a Tennessee owner should define

A process piping specification is the document that fixes, for each line class, the material, pressure rating, wall thickness, joints, valves, gaskets, bolting, examination, testing and cleaning, and it is the single most useful thing an owner can hand a piping contractor. Paul Industries works to the owner’s specification where one exists and writes one with the owner where it does not.

What a piping specification should settle before fabrication
ItemDecisionWhy it matters in Tennessee plants
MaterialCarbon steel, 304L or 316L stainless, duplex, nickel alloy, lined steel, thermoplasticChemical, metals and battery services vary widely in corrosion behavior
Rating and wallFlange class and schedule from design pressure, temperature and corrosion allowanceSets cost and weight of every spool
JointsButt weld, socket weld, flanged, threaded, sanitary clamp, orbital weldCategory M and high-purity lines restrict some joint types
ExaminationVisual, radiography or ultrasonic percentage, borescope for orbital weldsDrives schedule and turnover records
TestingHydrostatic, pneumatic or initial service leak test; test medium and chloride limitWinter testing in East Tennessee needs freeze protection
CleaningFlushing, blowing, chemical cleaning, passivationBattery, pharmaceutical and food lines need documented cleanliness

Process piping inspection and testing before a Tennessee startup

Inspection and testing before startup in Tennessee follow B31.3’s division of roles: the contractor examines its own work, by visual examination of every weld and by radiography or ultrasonic testing at the extent the fluid service requires, and the owner’s inspector verifies that the examination, testing and records meet the code and the specification. Paul Industries keeps a weld map that ties every weld to its welder, procedure, material heat numbers and examination result, so the owner’s inspector can trace any joint.

Testing follows examination. Systems are tested in sections where that shortens the critical path, with blinds, vents and drains planned so test water reaches every high point and leaves every low point. Instruments and equipment that cannot see the test pressure are isolated or removed. After testing, lines are flushed or blown to the cleanliness the process needs, and the test records, weld map, material certificates and as-built isometrics go into the turnover package with validation and commissioning in Tennessee where the owner’s quality system calls for it.

Tie-ins during planned outages

Tie-ins to live systems are the part of a piping job that most affects production, so Paul Industries plans them first. Field measurements of existing flanges and stubs feed the spool drawings, spools are fabricated and examined off site, and each tie-in has a written procedure listing isolation points, draining and purging, the work sequence, the test and the restart. Where a header cannot be shut down, a hot tap with a line stop places new branches on a pressurized line after a thickness survey confirms the wall. Distilleries and food plants schedule tie-ins between production campaigns, and chemical plants into turnarounds.

What sets the cost of a Tennessee piping project?

The cost of a Tennessee piping project is set mainly by material, pipe size, the number of welds, the examination extent and the access conditions at the plant. Alloy lines cost several times carbon steel, small-bore stainless with orbital welding and borescope inspection takes more hours per foot than large-bore carbon steel, and Category M or high-pressure service adds examination. Work inside an operating unit, at height, or within confined pipe racks adds labor, and outage-only tie-ins add premium time.

Paul Industries prices piping from the line list, P&IDs or isometrics where they exist, or from a site walk and a written scope where they do not. A budget range comes first from comparable work, then a firm price once the line classes, quantities and outage windows are agreed. Supply-only fabricated spools, design-build packages and complete installation with testing and turnover are all offered.

Owners can lower the price without lowering the quality by fixing line classes early, grouping tie-ins into fewer outages, accepting prefabricated spools in place of field-built runs, and giving clear access routes for material deliveries. Changes after spool fabrication starts are the most expensive kind, because finished spools must be cut, rewelded and reexamined, so Paul Industries holds a design review with the plant before releasing drawings to fabrication and records every agreed change in writing.

Who designs and installs plant process piping in Tennessee?

Paul Industries designs and installs plant process piping in Tennessee: B31.3 process lines in carbon steel, stainless and alloys, B31.1 steam, condensate and boiler piping, sanitary and high-purity tubing, chilled water and glycol, compressed air and nitrogen, and the pipe racks and supports that carry them. The scope covers design and stress checks, spool fabrication, installation, tie-ins, examination, testing, cleaning and turnover under one contract.

Once based in northern New Jersey, then Pennsylvania, Paul Industries is an East Coast contractor whose headquarters stand at 256 Shore Drive in Kilmarnock, Virginia. Process piping in Virginia is its headquarters-state service; its North Carolina and Georgia piping pages describe those states’ plants and codes; and it builds piping for owners in all 50 states and at plants abroad through its international work.

Process piping from Paul Industries across Tennessee

Paul Industries builds Tennessee piping from the line list to the turnover package, and ties it into the equipment it supplies: pressure vessel fabrication in Tennessee, tank fabrication in Tennessee and sanitary process piping in Tennessee, with welding under industrial welding services in Tennessee and spools from pipe fabrication. The state overview is on the Tennessee page. Send the line list, drawings or a scope description to request a quote, or call 201-450-8280.

Standards referenced: ASME B31.3 Process Piping · ASME B31.1 Power Piping · ASME Boiler and Pressure Vessel Code, Section I and Section IX · ASME BPE · Rules of the Tennessee Board of Boiler Rules, Chapter 0800-03-03 · 2021 International Mechanical, Plumbing and Fuel Gas Codes as adopted in Tennessee · Tennessee Contractors Licensing Act, T.C.A. Title 62, Chapter 6 · TDEC Air Pollution Control regulations

Frequently asked questions

Which industrial plants in Tennessee run the most process piping?

Chemical plants, battery and vehicle plants, metals processors, food and beverage plants and distilleries run the most process piping in Tennessee, along with power, nuclear fuel and pharmaceutical sites. The state counts more than 520 chemical and 870 food and beverage companies. Paul Industries designs and installs piping for each of those plant types.

Who installs chemical process piping in Kingsport and the Tri-Cities?

Paul Industries installs chemical process piping in Kingsport, Johnson City, Bristol and the Tri-Cities, in carbon steel, stainless and alloy, to B31.3 Normal and Category M service and B31.1 at the boilers. Work inside operating units is planned with the plant’s permit-to-work system and scheduled into turnarounds where tie-ins need the unit down.

Does Paul Industries pipe battery and vehicle plants in Spring Hill, Middle Tennessee and Chattanooga?

Paul Industries pipes solvent recovery, slurry, nitrogen, compressed air and process cooling systems for battery and vehicle plants around Spring Hill, Murfreesboro and Chattanooga. Lines in dry-room and solvent service get documented cleaning and leak testing, and work is phased to match line startups and retooling schedules.

Who builds process piping for plants in Memphis, Jackson and West Tennessee?

Paul Industries builds process piping for food, chemical and manufacturing plants in Memphis, Shelby County, Jackson and the rest of West Tennessee, including product, CIP, steam, glycol and compressed air systems. Memphis and Shelby County run their own building permits and Shelby County its own air program, which Paul Industries accounts for in planning.

Can Paul Industries install spirit and steam piping for a Lynchburg or Tullahoma distillery?

Paul Industries installs mash, beer, low wines, high wines and spirit transfer piping, along with steam to cookers and stills and CIP returns, for distilleries in Lynchburg, Tullahoma and across Middle Tennessee. Product lines are sanitary stainless; spirit lines are grounded, with jumpers across flanges, for flammable liquid service; and tie-ins are scheduled between production campaigns.

Does process piping inside a Tennessee plant need a building permit?

Process piping installed with new buildings, additions or building service changes is covered by the building permit, issued by state plan review or by the exempt municipality. Whether work confined to process lines inside an existing plant needs its own permit is the plan reviewer’s call, so Paul Industries checks with the jurisdiction during design.

Which edition of the mechanical and plumbing codes applies in Tennessee in 2026?

Since April 17, 2025, state plan review has applied the 2021 International Mechanical, Plumbing and Fuel Gas Codes, with plans submitted under the previous codes accepted until August 15, 2025. Exempt jurisdictions adopt their own editions, which must be within seven years of the newest published edition.

Which code governs steam piping at a boiler in Tennessee?

Steam piping from a power boiler to the first stop valve, or to the second stop valve where two or more boilers are connected, falls under ASME Section I and is designed, built, installed and tested to B31.1 under Rule 0800-03-03-.03(4). Welded piping in that zone carries code certification and data reports filed with the Chief Inspector.

Does a piping change at a Tennessee plant need an air permit revision?

A piping change needs an air permit review when it adds or changes an emission point, increases throughput of a permitted unit, or bypasses a control device. TDEC handles permits in 91 counties, while Davidson, Hamilton, Knox and Shelby counties run their own programs. Paul Industries identifies those changes in design so the plant can file in time.

How is process piping protected through an East Tennessee winter?

Water-filled lines in unheated areas get heat tracing and insulation, low-point drains and, where lines idle, glycol or blow-down procedures. Hydrostatic tests in cold weather use heated water or glycol mixes compatible with the process, and test sections are drained before nightfall. Paul Industries plans freeze protection into the test procedure for winter work in the mountains.

What is a hot tap, and when is it used at a Tennessee plant?

A hot tap connects a new branch to a pressurized line without shutting it down, by welding a fitting onto the live pipe and cutting through with a tapping machine, often paired with a line stop to isolate a downstream section. It suits headers that feed several units. Paul Industries confirms wall thickness, metallurgy and flow conditions before approving one.

What records does a Tennessee plant receive at the end of a piping job?

A Tennessee plant receives the weld map, welder and procedure qualifications, material certificates with heat numbers, examination reports, pressure test records, cleaning and flushing records, as-built isometrics and a punch list closeout. For B31.1 boiler external piping, the data reports go to the Chief Inspector as well. Paul Industries indexes the package by line number.

How much does process piping cost at a Tennessee plant?

Cost depends on material, diameter, weld count, fluid service, examination extent, access and outage constraints, so prices per foot vary several times between small-bore stainless and large-bore carbon steel. Paul Industries gives a budget range from comparable work once it has the line list or a site walk, then a firm price after scope and outages are agreed.

Can Paul Industries supply fabricated spools to a Tennessee plant as a supply-only order?

Paul Industries supplies fabricated, examined and tested spools to Tennessee plants as supply-only orders, built from the plant’s isometrics or from field measurements, tagged by line and spool number, and shipped with material certificates and weld records. The same spools are installed by Paul Industries when the order includes installation.

What does a process piping license mean for a Tennessee contract?

The Board for Licensing Contractors requires a license for contracting, bidding or negotiating a price on projects of $25,000 or more as prime contractor or construction manager, and for mechanical, plumbing or HVAC trade contracts whose portion reaches $25,000. Licenses from other states are not valid in Tennessee. Owners should confirm the requirement during procurement.

How long does a typical tie-in outage take at a Tennessee plant?

A planned tie-in outage lasts as long as isolation, draining, purging, the connection and the test take, which for prefabricated spools on a single header is often one shift. Complex unit tie-ins during turnarounds run longer. Paul Industries writes a tie-in procedure with durations for each step so the plant can plan production around a known window.

What should a Tennessee plant send to get process piping quoted?

Send the P&IDs and line list or a written scope, any isometrics or layout drawings, the owner’s piping specification, fluid service categories, required tie-in points and outage windows, testing and cleaning requirements, and the site address. Paul Industries returns a budget range first and a firm price once the details are confirmed.

Planning process piping work at a Tennessee plant?

Send the line list, drawings or a scope description and the outage windows the plant can give. Call 201-450-8280 or request a quote.