Paul Industries provides pressure vessel fabrication in Tennessee, designing and building ASME Section VIII vessels, receivers, reactors, columns, separators and jacketed process vessels for chemical, battery, nuclear, food and pharmaceutical plants across the state. Each vessel is built to the ASME Code that Tennessee adopts, carries National Board registration and its Manufacturer’s Data Report, and arrives ready for its first state certificate inspection. Paul Industries is headquartered at 256 Shore Drive, Kilmarnock, Virginia, and takes vessel work across Tennessee and in all 50 states.

Request a quote or call 201-450-8280

Headquarters 256 Shore Drive, Kilmarnock, Virginia
Statute T.C.A. 68-122 counts unfired pressure vessels as boilers
Thresholds Over 5 cubic feet and over 15 psig design pressure
Inspection Corrosive service: internal and external every two years
Certificate Valid up to 26 months, $60 state fee
Reviewed November 2026

How Tennessee law shapes pressure vessel fabrication in Tennessee

Pressure vessel fabrication in Tennessee is shaped by a statute that treats unfired pressure vessels as boilers: T.C.A. 68-122-102 defines a boiler to include any vessel pressurized from an external source or by an indirect application of heat. Air receivers, steam-heated kettles, heat exchanger shells, reactors and gas storage vessels therefore fall under the Board of Boiler Rules and the Department of Labor and Workforce Development, with the same certificate system that governs a steam boiler.

Rule 0800-03-03-.03 states the construction requirement plainly: no boiler or unfired pressure vessel is installed for operation in Tennessee unless it is designed, constructed, inspected, stamped and installed for its pressure and temperature under the applicable section of the ASME Code. The vessel bears National Board stamping with the manufacturer’s National Board number, and a copy of the Manufacturer’s Data Report, signed by the manufacturer and the National Board commissioned inspector, goes to the Chief Inspector when the vessel is shipped into the state. The general method of designing and building vessels is described on the pressure vessel fabrication page; this page covers the Tennessee requirements that sit around it.

What is considered a pressure vessel in Tennessee?

A pressure vessel in Tennessee, for the purposes of state inspection, is an unfired vessel larger than 5 cubic feet and designed for more than 15 psig, outside the categories the statute leaves out (T.C.A. 68-122-105). Below either threshold the vessel is outside the Act, although it is still designed to the ASME Code when the owner’s specification, insurer or plant standards ask for it, which most industrial buyers do.

When does a tank become a pressure vessel? In Tennessee the answer is a design question as much as a size question: an atmospheric storage tank that never sees more than 15 psig sits outside the boiler law and under fire code and tank rules, while the same diameter built for a nitrogen blanket at 50 psig becomes a state-inspected vessel. Paul Industries settles the design pressure, vacuum rating and relief settings with the owner at the data sheet stage, because that one number decides which rulebook the vessel lives under for its whole life.

  • Outside the Act: any unfired vessel at or under 5 cubic feet in volume, any designed for no more than 15 psig, LPG containers, containers meeting interstate commerce shipping rules, compressed air tanks on vehicles or on railroad property, federally controlled equipment, and the pressure chamber inside a medical or dental autoclave as the statute defines one.
  • Exempt from inspection and certificates: vessels holding only water under pressure for domestic supply at or below 200 degrees Fahrenheit, including those with an air cushion.

The autoclave exclusion, added in 2023, is narrow. The statute’s autoclave sterilizes reusable medical or dental equipment for a health care licensee and is regulated by the FDA, so a production sterilizer or retort in a pharmaceutical or food plant should be planned as a state-inspected vessel unless the Chief Inspector confirms otherwise.

Tennessee pressure vessel regulations from design to first certificate

Tennessee pressure vessel regulations follow the vessel from its design calculations to its first posted certificate, and each step leaves a record the owner keeps for the life of the vessel. A vessel built outside Tennessee is inspected during construction by an inspector holding a National Board commission or an equivalent state certificate of competency (T.C.A. 68-122-110(e)), which is the Authorized Inspector who signs the data report.

Steps from purchase order to an operating vessel in Tennessee
StepWhat happensTennessee requirement
Data sheet and designDesign pressure and temperature, MDMT, corrosion allowance, nozzle loads, wind and seismic loads, relief casesLatest ASME Code edition adopted by Rule .02
Materials and weldingPlate, forgings and pipe to ASME Section II; procedures and welders qualified to Section IXCode construction under Rule .03(1)
Inspection during constructionAuthorized Inspector hold points, radiography or ultrasonic examination, hydrostatic or pneumatic testInspector with National Board commission (T.C.A. 68-122-110(e))
Stamping and registrationASME Certification Mark with designator, National Board number, Manufacturer’s Data ReportData report filed with the Chief Inspector on shipment into Tennessee (Rule .03(2))
InstallationSetting, anchoring, piping, relief devices, insulation that leaves the nameplate visible or its location recordedInstallation permit first for vessels stamped lethal service (Rule .04(1))
First certificate inspectionInspector checks the vessel, nameplate, relief devices and supports, and attaches the state registration tagCertificate valid up to 26 months, $60 fee

Most pressure vessel requirements in Tennessee therefore land on the manufacturer and the owner rather than on a state plan review: there is no state design approval for an ordinary ASME vessel, but the paperwork chain has to be complete before the first inspector arrives. Vessels stamped for lethal service are the exception, because they need a state installation permit, with layout drawings and the data report, before any installation work begins.

How often do pressure vessels need to be inspected in Tennessee?

How often do pressure vessels need to be inspected under Tennessee law? A vessel whose contents corrode it is inspected internally and externally every two years where its construction permits, and the Board of Boiler Rules may set longer periods (T.C.A. 68-122-110(a)(3)). A vessel holding contents known to be noncorrosive, or adequately treated with an inhibitor, is inspected externally at intervals the Board sets and needs no internal inspection, provided it was built to the Board’s rules or an equivalent standard.

The certificate issued after a satisfactory inspection is valid for up to 26 months and costs $60 under Rule 0800-03-03-.14. The inspection fee for an unfired vessel is $30 for a cross-sectional area of 50 square feet or less, plus $8 for each further 100 square feet, with no more than $100 per day of an inspector’s time on any one vessel. Vessels covered by boiler insurance are inspected by the insurer’s Special Inspector, and plants that run their own Owner-User Inspection Agency inspect their unfired vessels with their own commissioned inspectors, who are not authorized to inspect boilers.

What the owner prepares before an internal

The owner prepares a vessel for internal inspection to the extent the inspector asks, which typically means draining, cleaning, venting, blinding inlet and outlet lines, and testing the atmosphere for 19.5 to 23.5 percent oxygen before entry (Rule .05). If an inspector needs to see behind a lining, insulation or brickwork, the owner removes it (Rule .12(3)). Paul Industries designs inspection openings, davits and removable insulation panels into new vessels so those internals cost less every two years.

Tennessee Special and Tennessee Standard vessels

Tennessee Special and Tennessee Standard are the two routes in the Tennessee boiler and pressure vessel rules for vessels that differ from a normal ASME and National Board stamped unit (Rule 0800-03-03-.03). A Tennessee Special is a vessel of special design, or one that cannot bear ASME and National Board stamping; its details, including shop drawings, go to the Chief Inspector, and the Board approves construction and installation before any construction starts.

A Tennessee Standard vessel is built by an owner-user that the state authorizes as an Owner-User Inspection Agency and that holds a valid ASME Certificate of Authorization. The vessel meets every requirement of ASME Section VIII, Division 1, is inspected by the owner-user’s own inspector holding a Tennessee certificate of competency, and is used only by that owner-user, never resold. Buyers who need a vessel to move between sites or be sold later order a standard ASME and National Board vessel, which is the route Paul Industries builds to by default.

Standard ASME, Tennessee Special and Tennessee Standard vessels compared
RouteWho approves before constructionMarkingLimits on use
Standard ASME vesselNo state design approval; Authorized Inspector accepts constructionASME Certification Mark and National Board numberAny owner, resale and relocation allowed with reinstall approval
Tennessee SpecialBoard of Boiler Rules, on details and shop drawings sent to the Chief InspectorAs the Board’s approval sets outBuilt for the approved installation; leaving the state needs Board approval to return
Tennessee StandardOwner-User Inspection Agency’s own inspector under its ASME certificateStamped “Tennessee Standard”Used only by that owner-user, never resold

The choice matters most for owners who move equipment between plants or plan to sell a line later, because only the standard route produces a vessel that any buyer and any jurisdiction will accept on its stamping alone. A Tennessee Standard vessel suits a large chemical or metals producer with its own inspection agency and a vessel that will never leave its site. A Tennessee Special suits the rare design the ASME Code does not cover. Paul Industries recommends the standard route unless the owner has a specific reason to choose another, and it prepares the drawings and calculations a Special submittal needs when one is chosen.

Designing vessels for Tennessee chemical, battery, nuclear and food plants

Vessels for Tennessee plants are designed around the processes that dominate each region, and the state’s own economic development department reports more than 520 chemical companies in Tennessee, with chemical industry employment 50 percent above the national average. Eastman has its headquarters and largest manufacturing site in Kingsport, and the department describes Korea Zinc’s more than $6.6 billion in Clarksville and Gordonsville as the largest single private corporate investment in state history. The companies here are named only as market facts.

Tennessee industries and the pressure vessels they typically order
Industry and regionTypical vesselsDesign points
Chemicals, Tri-Cities and KingsportReactors, columns, receivers, separators, heat exchanger shellsCorrosion allowance and alloy selection for the process; biennial internals for corrosive service
Battery cells, Spring Hill and Middle TennesseeSolvent and slurry vessels, nitrogen and compressed air receivers, chilled water expansion tanksLow-moisture service, cleanliness, inert gas blanketing; Ultium Cells is retooling Spring Hill for LMR prismatic cells through 2028
Nuclear fuel and research, Oak RidgeProcess and gas handling vessels at private facilities near the federal sitesDocumentation depth, material traceability, owner quality program flow-downs
Industrial gases, Bradley County and ChattanoogaStorage and buffer vessels, separators, receiversHigh design pressures, low MDMT, impact testing; Linde announced a Bradley County expansion in 2025
Metals processing, ClarksvilleProcess vessels for new nonferrous metals productionAbrasion and corrosion allowances, lined or clad construction
Food, beverage and distilling, Memphis, Lynchburg and statewideJacketed kettles, CIP and hot water vessels, air receiversSanitary finishes inside, ASME jackets outside, relief sized for steam supply

What are pressure vessels made of for Tennessee service?

What are pressure vessels made of in these plants? Carbon steel such as SA-516 Grade 70 plate covers most air, water, steam and hydrocarbon service; 304L and 316L stainless steels cover food, pharmaceutical and many chemical services; duplex grades and nickel alloys handle chloride and acid service; and clad plate puts a corrosion-resistant layer over a carbon steel backing when a thick vessel would be too costly in solid alloy. Paul Industries selects material against the process data, the corrosion allowance and the inspection interval the owner wants to live with.

How are pressure vessels manufactured for a Tennessee plant?

Pressure vessels for a Tennessee plant are manufactured in a sequence of design, material receipt, forming, welding, examination, testing and stamping, with the Authorized Inspector involved at each hold point. Plate is cut and rolled, heads are formed, longitudinal and circumferential seams are welded to qualified procedures, nozzles and reinforcing pads are fitted, and seams are examined by radiography or ultrasonic testing to the extent the joint efficiency in the design calls for. Postweld heat treatment follows where thickness, material or lethal service require it, then the hydrostatic test, normally at 1.3 times the MAWP for Division 1 vessels adjusted for temperature, before stamping and coating.

High pressure vessel fabrication, where wall thickness and design margins push a vessel toward ASME Section VIII, Division 2, adds design-by-analysis, tighter material testing and more examination, but it can shave weight and cost from thick vessels. Paul Industries compares Division 1 and Division 2 for heavy-wall vessels before quoting, and prefabricates vessel skids and piping off site so the installation window at the plant stays short.

Relief protection Tennessee requires on every vessel

Every Tennessee pressure vessel carries relief devices sized so that pressure cannot rise more than 10 percent above the highest relief setting, with the lowest set at or below the vessel’s maximum allowable working pressure (Rule 0800-03-03-.12(4)). Where fire or another unexpected heat source adds a hazard, relief sizing follows ASME Section VIII, Division 1, UG-125, or Division 2, paragraph 9.2. The devices are installed so they cannot be made inoperative.

Vessels fed through a pressure-reducing valve need relief protection on the low-pressure side whenever downstream equipment cannot take the full upstream pressure, sized for the reducing valve failing open and for any manual bypass, with a pressure gauge on the low side (Rule .04(4)). Paul Industries sizes relief valves and rupture discs with the vessel, checks inlet and outlet piping losses, and routes discharges away from walkways and platforms.

Supports, clearances and platforms around a Tennessee vessel

Tennessee’s rules also reach the steel and space around a vessel. Each vessel stands on masonry or structural supports strong and rigid enough to carry it full, with no excessive vibration in the vessel or its connecting piping (Rule 0800-03-03-.04(10)). A vessel with a manhole keeps 5 feet of clear space between the manhole opening and any wall, ceiling or pipe that would stop a person from entering (Rule .08(4)), which often decides the orientation of a vertical vessel in a crowded building. Where platforms or runways are needed for safe access across the tops of adjacent vessels, the walkway has two remote means of exit. Paul Industries lays out skirts, legs, saddles, lugs, platforms and ladders with the vessel design, so the installation passes those checks at the first certificate inspection instead of being reworked on site.

Moving, reinstalling or buying a used vessel in Tennessee

When moving a pressure vessel into, within or back into Tennessee, the owner applies to the Chief Inspector with an Application for Permission to Reinstall, and a Deputy Inspector inspects the vessel once the application is approved (Rule 0800-03-03-.04(2)). A second-hand vessel is installed only after that approval. A standard vessel sent out of state for temporary use or repair comes back through the same application, while a nonstandard vessel that leaves the state needs additional Board approval to return.

A used vessel is only as good as its paperwork. Paul Industries checks the nameplate against the data report, measures wall thickness, reviews the corrosion history and relief devices, and, where the original records are gone, explains to the owner what the inspector will accept. Where a used vessel cannot be documented, a new one built to the current ASME edition is often the quicker path to a certificate.

Rerates, repairs and alterations on Tennessee vessels

A rerate in Tennessee is an alteration even when nothing is welded, because Rule 0800-03-03-.01 counts a non-physical increase in maximum allowable working pressure or design temperature, or a lower minimum design metal temperature, as an alteration. The MAWP of an existing standard vessel is never raised above its nameplate and data report without prior approval from the Chief Inspector (Rule .12(1)), and the alteration is documented on National Board Form R-2 after the in-service inspector accepts it.

Welded repairs and alterations follow Rule .07: the in-service inspector is consulted before work starts and accepts it afterward, the work follows the NBIC, and it is made under a National Board R Certificate of Authorization with the state license the rule cites. Tennessee accepts NBIC routine repairs under Board Case BC 12-18, but never for Section VIII, Division 2 or Division 3 vessels, and never with the nameplate and stamping requirements waived. When a vessel’s stamping becomes hard to read, restamping happens only with the Chief Inspector’s authorization and in an inspector’s presence, and only the original manufacturer reapplies the ASME mark.

What does pressure vessel fabrication in Tennessee cost?

The cost of pressure vessel fabrication in Tennessee is set mostly by material, thickness and examination, and much less by the state’s fees, which run to $60 for a certificate and $30 and up for an inspection. Material is usually the largest share, and alloy choice can multiply the price of the same shell several times over. Thickness drives welding hours, postweld heat treatment and examination; nozzle count and internals drive fitting hours; and impact testing for low MDMT, full radiography, lethal service and documentation packages add cost in steps.

Paul Industries prices a vessel from the data sheet or process conditions: fluid, design pressure and temperature, volume or dimensions, material preference, nozzle schedule, code division, and any owner specifications. A budget range comes first from comparable vessels, followed by a firm price once the design calculations confirm thickness and weight. Supply-only, design-build and complete installation with piping and startup are all priced from the same package.

Who designs and builds ASME pressure vessels in Tennessee?

Paul Industries designs and builds ASME pressure vessels in Tennessee for chemical plants, battery and vehicle plants, industrial gas sites, nuclear and research facilities, food and beverage plants and pharmaceutical sites. The scope covers process design input, ASME calculations, material procurement, fabrication with Authorized Inspector hold points, testing, National Board registration paperwork, delivery and setting, piping, relief devices, insulation and the first certificate inspection. Paul Industries also handles rerates and alterations of vessels already in Tennessee service.

Formerly based in northern New Jersey, then Pennsylvania, Paul Industries now works as an East Coast contractor out of its Kilmarnock, Virginia headquarters, and in Virginia pressure vessel fabrication in Virginia is its headquarters-state service. Its vessel pages for North Carolina and Georgia cover those states’ rules, and its vessels go to owners nationwide and abroad through its international projects. Chemical clients will find the wider picture on the chemical manufacturing page.

Pressure vessels from Paul Industries for Tennessee owners

Paul Industries delivers ASME pressure vessels to Tennessee plants complete with the data report, nameplate, relief devices and test records the first state inspection checks, and installs them with the connecting process piping in Tennessee. Related work covers boiler repair in Tennessee, tank fabrication in Tennessee, industrial welding services in Tennessee, validation and commissioning in Tennessee and hydrostatic testing, with the state overview on the Tennessee page. Send a data sheet or process conditions to request a quote, or call 201-450-8280.

Standards referenced: Tennessee Code Annotated Title 68, Chapter 122 · Rules of the Tennessee Board of Boiler Rules, Chapter 0800-03-03 · ASME Boiler and Pressure Vessel Code, Section VIII, Divisions 1 and 2 · ASME Section II and Section IX · National Board Inspection Code (NBIC) · Board Case BC 12-18

Frequently asked questions

Who builds pressure vessels for chemical plants in Kingsport and the Tri-Cities?

Paul Industries builds ASME pressure vessels for chemical plants in Kingsport, Johnson City, Bristol and the rest of the Tri-Cities: reactors, columns, receivers and exchanger shells in carbon steel, stainless and nickel alloys. Corrosive-service vessels there face a biennial internal under Tennessee law, so Paul Industries details manways, internals and linings that keep those inspections short.

Does Paul Industries fabricate vessels for battery and vehicle plants around Spring Hill and Nashville?

Paul Industries fabricates solvent, slurry, nitrogen and compressed air vessels for battery cell and vehicle plants around Spring Hill, Nashville and Murfreesboro. Ultium Cells’ $1 billion retool of its Spring Hill plant, due for completion in 2028, is one sign of the process equipment demand there. Vessels for dry-room and solvent service get extra attention to cleanliness and moisture control.

Who supplies pressure vessels to Memphis, Chattanooga and Knoxville plants?

Paul Industries supplies pressure vessels to plants in Memphis, Shelby County, Chattanooga, Knoxville and Oak Ridge, from air receivers and jacketed kettles to gas storage vessels and process separators. Each vessel ships with its data report filed for Tennessee, and Paul Industries sets and pipes it at the plant when the order includes installation.

Is there a separate Tennessee boiler and pressure vessel code?

Tennessee writes no construction code of its own; the Board of Boiler Rules adopts the latest ASME Boiler and Pressure Vessel Code and the latest NBIC in Rule 0800-03-03-.02. The state’s own requirements cover scope, registration, inspection intervals, certificates, installation permits, the Tennessee Special and Tennessee Standard routes, and repair authorization.

Do air receivers need a Tennessee certificate?

An air receiver larger than 5 cubic feet with a design pressure above 15 psig is an unfired pressure vessel under Tennessee law and needs a certificate after inspection, unless it is mounted on a vehicle or railroad right-of-way. Receivers hold noncorrosive contents in most cases, so they get external inspections at the Board’s intervals, but condensate draining still decides how long they last.

What does the state registration tag on a Tennessee vessel mean?

The registration tag is a Board-approved, Department-supplied tag the inspector fastens near the code stamping when a new vessel is installed or an existing one gets its first certificate inspection. It carries the state number used on every later inspection report and certificate. The ASME and National Board stamping stays exposed, or its location is recorded so it can be uncovered.

Can a plant's own inspectors inspect its pressure vessels in Tennessee?

A company the state accepts as an Owner-User Inspection Agency employs Special Inspectors with Tennessee certificates of competency to inspect the unfired vessels it operates, and its owners then pay no state inspection fees on those vessels. Those inspectors are not authorized to inspect boilers, and their reports go to the Chief Inspector within 30 days like any other.

What hydrostatic test does Tennessee allow on a vessel already in service?

A pressure test on a vessel in service is never more than 1.5 times its maximum allowable working pressure, and stays within what the original ASME construction code allows. When the contents rule out water, another test medium is used under the NBIC’s precautions. Paul Industries plans the test medium, blinds and relief valve gags with the inspector beforehand.

Does a vessel built in another state need anything extra to run in Tennessee?

A vessel built in another state is inspected during construction by an inspector with a National Board commission, carries ASME and National Board stamping, and has its Manufacturer’s Data Report filed with Tennessee’s Chief Inspector when it ships into the state. It then gets its first certificate inspection and state tag once installed.

Who approves a vessel that cannot carry ASME stamping in Tennessee?

The Board of Boiler Rules approves it as a Tennessee Special after the Chief Inspector receives the construction details and shop drawings, and approval comes before construction starts. Paul Industries prepares the calculations and drawings for that submittal when an owner’s design truly falls outside the Code, though a standard ASME vessel is usually faster.

How is a jacketed kettle treated under Tennessee rules?

A steam jacket over 15 psig and 5 cubic feet makes a kettle an unfired pressure vessel under Tennessee law, while directly fired jacketed kettles have their own rule, 0800-03-03-.09. Paul Industries builds the jacket to ASME Section VIII with its own relief valve and keeps the product side to sanitary finishes.

Do vessels at Oak Ridge fall under the state program?

Vessels under federal control are outside the Tennessee Act, so equipment operated by the federal government follows federal programs. Privately owned plants in Oak Ridge, including the new fuel and research facilities at the Horizon Center, fall under the state program like any other Tennessee owner. Paul Industries confirms the governing program at the start of each order.

Do nameplates have to stay visible under insulation in Tennessee?

Code stamping is kept exposed rather than hidden by lagging or paint, unless the owner keeps a record of where it sits so it can be uncovered when the inspector asks (Rule 0800-03-03-.04(7)). Paul Industries fits removable insulation panels or stand-off nameplate brackets on insulated vessels.

How long does a custom ASME vessel take to reach a Tennessee plant?

Lead time depends mostly on material availability, design review and examination: carbon steel receivers move faster than alloy reactors with forged nozzles and full radiography. Paul Industries gives a schedule with the quote, lists the material and inspection milestones, and updates it as approvals come back.

Which delivery routes does Paul Industries offer Tennessee vessel buyers?

Paul Industries offers all three routes for Tennessee buyers: supply-only vessels delivered with their documents, design-build from process conditions, and complete installation with setting, piping, relief devices, insulation and startup support. The route changes the price and schedule, so the request should say which is wanted.

What should go into a pressure vessel quote request for a Tennessee plant?

Include the process fluid, design pressure and temperature, MDMT, volume or dimensions, material preference, nozzle list, orientation and supports, code division, relief requirements, any owner specifications, the delivery site and the date needed. With those, Paul Industries returns a budget range first and a firm price after the calculations confirm the design.

Need an ASME pressure vessel for a Tennessee plant?

Send the data sheet or process conditions, the code division and the delivery date you are working to. Call 201-450-8280 or request a quote.