Paul Industries provides industrial welding services in Illinois for refineries, heavy equipment manufacturers, corn and oilseed processors, pharmaceutical, food and chemical plants, utilities and commercial buildings, welding pipe, pressure equipment, structural steel and worn or cracked machinery to the code each job requires. Illinois adds its own layers to the national codes: the State Fire Marshal’s boiler and vessel repair rules, Chicago’s separate boiler program, grain-dust hot work rules in the state’s elevators and mills, and winters that put welding below freezing for months. Paul Industries plans each job around those conditions before the first arc.

Request a quote or call 201-450-8280

Headquarters 256 Shore Drive, Kilmarnock, Virginia
Pressure welding ASME Section IX, 2025 Edition, adopted April 13, 2026
Boiler and vessel welds Inspector authorization before work (41 Ill. Adm. Code 2120.1041)
Structural cold limit AWS D1.1: no welding below 0 F unless heated
Radiography Illinois Emergency Management Agency, 32 Ill. Adm. Code 350
Reviewed November 2026

What do industrial welding services in Illinois cover?

Industrial welding services in Illinois cover new construction and repair welding on process and power piping, boilers, pressure vessels and tanks, structural steel, platforms and supports, and the frames, buckets, shafts and housings of production machinery. A single plant may need all of them in one outage: a refinery replacing exchanger nozzles and a pipe rack, a Decatur wet mill rebuilding conveyors and steam lines, or a Quad Cities equipment plant repairing fixtures and building a new paint line.

The common thread is qualification. Every code weld is made with a written welding procedure specification, supported by a procedure qualification record, by a welder qualified on that procedure, and examined to the acceptance criteria of the governing code. Illinois boiler and vessel rules adopted the 2025 Edition of ASME Section IX effective April 13, 2026, so pressure-boundary welding in the state is now qualified to that edition.

What is industrial welding at an Illinois plant?

What is industrial welding, as distinct from fabrication welding in a factory? Industrial welding is welding done to plant equipment, piping and structures where they stand or are being installed, under the owner’s safety rules, isolation program and production schedule, and to the code that governs the system being welded. At an Illinois plant it ranges from orbital tube welds on a pharmaceutical skid to submerged arc hardfacing on a crusher roll, and from root passes on a 24 inch steam line to stud welding on a deck.

The processes follow the job. Gas tungsten arc welding (GTAW) gives clean, controlled roots on stainless and alloy pipe; shielded metal arc welding (SMAW) handles carbon steel pipe and structural work in wind and awkward positions; flux-cored and gas metal arc welding (FCAW, GMAW) speed up plate and structural joints; submerged arc welding (SAW) builds up and hardfaces large wear surfaces; and orbital GTAW makes repeatable sanitary tube welds. Paul Industries fixes the process in the written procedure before the job starts.

Which welding code governs which Illinois job
WorkGoverning codeQualificationTypical examination
Process piping in refineries, chemical and API plantsASME B31.3ASME Section IXVisual plus radiography or ultrasonic by fluid category
Steam, feedwater and condensateASME B31.1; Section I for boiler external pipingASME Section IXVisual, radiography or ultrasonic by size and temperature
Boiler and pressure vessel repairsNBIC Part 3 under 41 Ill. Adm. Code 2120ASME Section IXAs the inspector requires; NDE to prove defect removal
Structural steel, platforms and supportsAWS D1.1AWS D1.1 or prequalified proceduresVisual, ultrasonic or magnetic particle on critical joints
Stainless structural and food equipment framesAWS D1.6AWS D1.6Visual, liquid penetrant
Sanitary tube in food, dairy and pharmaceutical plantsASME BPE or AWS D18.1ASME Section IX, orbital proceduresVisual inside and out by borescope
Aboveground storage tank repairsAPI 653 with API 650ASME Section IXVisual, vacuum box, radiography on shell repairs
Pipelines into terminals and plantsAPI 1104API 1104Radiography or ultrasonic

Welding on Illinois boilers and pressure vessels

Welding on an Illinois boiler or pressure vessel is regulated as a repair or alteration from the moment it touches a pressure-retaining boundary. The Boiler and Pressure Vessel Repairer Regulation Act (225 ILCS 203), as written into 41 Ill. Adm. Code 2121, treats any organization performing such welding as a repairer, and Section 2120.1041 of the boiler rules bars starting a weld repair on a pressure vessel or high pressure boiler until the inspector has accepted the procedure, the welders and the method.

The rules then govern technique. A crack is removed completely and the removal proved by nondestructive examination before welding; a through-thickness defect is closed with a complete penetration weld; wasted areas are built up only where the inspector judges the strength unimpaired. Inside Chicago, boiler repairs follow the city’s own approval rules under the Department of Buildings. Paul Industries plans the weld, the examination and the paperwork together, and the repair side is set out on boiler repair in Illinois and pressure vessel fabrication in Illinois.

Heavy equipment and wear repair in Peoria, the Quad Cities and Decatur

Heavy equipment and wear repair welding is a large part of Illinois industrial work because the state builds and runs heavy machinery. Caterpillar reported more than 17,000 employees across Illinois in July 2026, with manufacturing including East Peoria, and Deere called workers back in September 2026 to its East Moline combine works and its Moline seeding and cylinder plants. Ingredient and grain plants in Decatur and across central Illinois run hammer mills, conveyors, elevators, screw presses and dryers that wear every season.

Repair welding on that equipment means crack repairs on frames, booms and housings with the crack located and mapped by magnetic particle or dye penetrant testing, drilled at the ends and gouged out before welding; rebuilds of shafts, bores and keyways by weld build-up and machining; and hardfacing of buckets, liners, flights and rolls with wear-resistant alloys matched to abrasion or impact. Preheat and interpass temperatures follow the base metal’s carbon equivalent and thickness, which matters on the quenched and tempered and high-strength steels common in equipment frames.

Hot work in grain, ingredient and refinery plants

Hot work in an Illinois grain, ingredient or refinery plant starts with a written permit, because combustible dust and flammable vapors turn a spark into a fire or an explosion. OSHA’s welding standard, 29 CFR 1910.252, and NFPA 51B set the general permit, fire watch and combustible-clearance rules, and OSHA’s grain handling standard, 29 CFR 1910.272, requires a hot work permit for welding in the facilities it covers: grain elevators, feed mills, flour mills, rice mills, dust pelletizing plants, dry corn mills and soybean flaking operations. Wet mills and other ingredient plants with dust hazards apply the same discipline through their own combustible dust programs.

Paul Industries works inside each plant’s hot work program: dust cleanup and wet-down before work, covering or isolating openings and conveyors, gas testing in vapor areas, spark containment with fire-resistant blankets and enclosures, a trained fire watch through the work and after it, and a closed permit at the end. Tank work adds its own steps; hot work that penetrates a regulated underground tank is scheduled with the State Fire Marshal under Part 175, and repairs to aboveground tanks are covered on tank fabrication in Illinois.

Pipe welding on Illinois steam, process and utility lines

Pipe welding on Illinois plant lines takes up a large part of the welding hours in a typical outage, because steam, condensate, process, compressed air and cooling water piping all age, corrode and get rerouted as plants change. Carbon steel steam and condensate lines are commonly welded with a GTAW root and SMAW fill and cap; chrome-moly lines in refinery and power service need preheat and post-weld heat treatment set by the material group and thickness; and stainless process lines take a purged GTAW root to keep the inside free of heavy oxide.

Condensate lines deserve special attention in Illinois plants. Carbonic acid in condensate thins carbon steel at the bottom of the pipe and at fittings, so a leak often signals a wider problem. Paul Industries measures thickness around a failed section before cutting, replaces the thinned run rather than the leaking fitting alone, and flags the treatment question for the plant’s water program. Butt welds are the default; socket welds are kept to small bore lines where the specification allows them, because crevices in socket welds can trap condensate and start corrosion.

Structural welding for platforms, mezzanines and equipment supports

Structural welding in Illinois plants covers access platforms, stairs and ladders, mezzanines, pipe racks, equipment supports, crane runway repairs and reinforcement of existing steel for new loads, all welded to AWS D1.1 for carbon steel or AWS D1.6 for stainless. Prequalified joint details in D1.1 let much of that work proceed without separate procedure testing, while unusual joints, steels or positions need qualified procedures.

Existing Illinois plants often carry steel decades old, sometimes of unknown grade, and welding new members to it calls for checking weldability first: a carbon equivalent from a chemical test of a sample, or preheat set conservatively when the grade is unknown. Paul Industries reviews the structural design for the new load, confirms the existing steel, fabricates new members off site where possible and field-welds the connections with the inspection the engineer of record specifies.

Welder and procedure qualification for Illinois code work

Welder and procedure qualification is what lets an inspector accept a code weld in Illinois, and the paperwork follows a fixed structure under ASME Section IX and AWS D1.1. The procedure qualification record proves the procedure produces sound welds with the required mechanical properties; the welding procedure specification tells the welder the ranges to use; and each welder’s performance qualification and continuity record proves that person can make the weld and has kept the skill current.

Qualification records an Illinois inspector reviews
RecordWhat it provesCode basisWhen the inspector asks for it
Procedure qualification record (PQR)The procedure produced a sound test weld with the required strength and toughnessASME Section IX, AWS D1.1Before a pressure repair is authorized
Welding procedure specification (WPS)The ranges of process, filler, preheat, position and heat treatment the welder must followASME Section IX, AWS D1.1At authorization and during the work
Welder performance qualification (WPQ)The welder passed a test weld within the WPS rangesASME Section IX, AWS D1.1Before the welder starts
Continuity logThe welder has used the process within the code’s time limitASME Section IX (six months), AWS D1.1On review of welder files
Weld map and examination reportsEach weld is traceable to a welder, procedure and inspection resultOwner specification and codeAt acceptance and turnover
National Board R-1 or R-2The boiler or vessel repair or alteration was made and acceptedNBIC Part 3; 41 Ill. Adm. Code 2120.40(v)On completion of pressure work

Choosing an industrial welding service for a single repair

A plant buying an industrial welding service for one repair needs the same evidence on a smaller scale: the procedure for the material, a qualified welder, and an examination record. Paul Industries provides those for single repairs as it does for outage packages, so a one-day job leaves the same trail as a turnaround. The repair is scoped from photographs or a site look, the material is identified from drawings, nameplates or a field test, and the examination is chosen to match the code and the consequence of a failure, whether that is a visual check on a guard or volumetric testing on a steam line.

Cold weather welding through an Illinois winter

Cold weather welding is a planning issue in Illinois from November to March, when outdoor steel, pipe racks and tank shells sit below freezing for weeks and the codes respond with preheat and enclosure rules. AWS D1.1 bars structural welding when the ambient temperature is below 0 F unless the welding area is heated, and it requires base metal below 32 F to be warmed before welding; moisture, wind and cold steel also raise the risk of hydrogen cracking and porosity on pipe and pressure welds.

Paul Industries builds heated, windproof enclosures around outdoor joints, preheats with induction or resistance equipment that holds and records temperature, stores low-hydrogen electrodes in heated ovens, and schedules post-weld heat treatment so the joint cools under control. On outdoor stainless and sanitary piping, enclosures also hold the purge gas steady, which keeps the root bright through cold, gusty days.

Plant welding, Chicago, IL to the Metro East: what each area asks for
AreaTypical plantsWelding most requested
Chicago and Cook CountyFood and beverage, hospitals, high-rise buildings, metalworkingSteam and hot water piping, sanitary tube, structural supports, boiler repairs under the city program
North Shore and Lake CountyPharmaceutical and API plantsOrbital stainless tube, B31.3 solvent piping, documented welds for qualification
Elk Grove Village and the northwest suburbsData centers, plastics, metal fabricationChilled water and fuel piping, equipment supports, roof and platform steel
Joliet, Will County and LemontRefineries, chemical plants, distribution centersTurnaround piping, exchanger and vessel repairs, tank repairs
Aurora, the Fox Valley and RockfordMachinery, aerospace, food and packagingMachine repair, compressed air piping, structural mezzanines
Peoria and the Quad CitiesHeavy equipment and farm machinery plantsCrack repair, fixture and frame welding, hardfacing, plant utilities
Decatur, Springfield and Champaign-UrbanaCorn and soybean processing, state and campus plantsConveyor and elevator repair, steam and syrup piping, campus steam mains
Metro East and Wood RiverRefinery, chemical and terminal operationsB31.3 piping, tank and vessel repairs, pipeline tie-ins

Stainless and sanitary welding for Illinois food and pharmaceutical plants

Stainless and sanitary welding for Illinois food, dairy, beverage and pharmaceutical plants is judged by the inside of the tube, where product touches the weld. Orbital GTAW with an argon purge produces full-penetration welds with smooth, low-oxide roots; weld coupons are made at the start of each shift or setup and examined before production welds proceed; and a sample or all of the production welds are inspected by borescope, as ASME BPE or AWS D18.1 and the owner’s specification require.

Paul Industries logs each sanitary weld on a weld map with welder, machine, heat numbers and inspection result, and passivates the system before it is cleaned and put into product. Plants with allergen or residue problems can follow the cleaning and passivation side on passivation services in Illinois, and the piping layout itself on process piping in Illinois.

How are welds examined in a running Illinois plant?

Welds in a running Illinois plant are examined by the method the code calls for, chosen so the examination can proceed safely beside operating equipment. Visual examination comes first on every weld; liquid penetrant and magnetic particle testing find surface cracks; and volumetric examination by radiography or ultrasonic testing, including phased array, finds internal defects in pipe and pressure welds.

Radiography in Illinois is governed by the Illinois Emergency Management Agency’s rules for industrial radiographic operations in 32 Ill. Adm. Code 350, and it requires roped-off radiation areas that can clear a pipe rack or a production floor. Ultrasonic and phased array testing avoid the exclusion zone and are often accepted in place of radiography under B31.3 and B31.1, so Paul Industries plans the examination method with the owner’s inspector before the job is scheduled, to keep production running beside the work.

How do welding companies in Chicago, Illinois and downstate compare on records?

Welding companies in Chicago, Illinois and downstate should be compared on the records they hand over, because a code weld without its paperwork is a weld the inspector cannot accept. Buyers sorting Chicago welding companies, or Illinois welding companies anywhere in the state, should expect the welding procedure specifications and qualification records, each welder’s continuity log, material test reports, the weld map, examination reports and, for pressure work, the National Board R-1 or R-2 report and the inspector’s acceptance.

Paul Industries delivers that set with every code job, sorted by system and weld number. Industrial maintenance welding, Chicago and statewide, gets the same discipline in lighter form: a work order, the procedure used, the welder and the inspection result, so the plant’s maintenance history shows what was welded and how.

What do industrial welding services in Illinois cost?

The cost of industrial welding services in Illinois is set by the material and thickness, the code and its examination level, access and position, preheat and heat treatment, the plant’s safety and permit requirements, and whether the work happens during production or in a planned outage. Stainless, alloy and sanitary welding take more time per joint than carbon steel; radiography and heat treatment add crews and schedule; and winter work adds enclosures and heat. Welding on Illinois public works is priced at the county rates the Department of Labor sets under the Prevailing Wage Act.

Paul Industries prices an Illinois welding job from drawings or photographs, the material and code, joint counts or wear areas, the access and outage window, and the examination required, with a budget range from comparable work and then a firm price once the scope is fixed. Owners can buy an industrial welding service on its own, a design-build repair that includes engineering, or complete fabrication and installation of the equipment being welded.

Who provides industrial welding services in Illinois?

Paul Industries provides industrial welding services in Illinois at refineries, equipment plants, ingredient processors, pharmaceutical and food plants, utilities and buildings, from Chicago and its suburbs to Rockford, Peoria, Decatur, Springfield, the Quad Cities and the Metro East. From its headquarters at 256 Shore Drive in Kilmarnock, Virginia, Paul Industries, an East Coast contractor, accepts welding work across Illinois and the Midwest, in every state and at plants abroad through its international program.

Industrial welding from Paul Industries for Illinois plants

Paul Industries welds pipe, pressure equipment, tanks, structural steel and machinery, qualifies the procedures and welders, examines and documents every code weld, and repairs and rebuilds worn and cracked equipment, with fabrication of new steel and spools under the same contract through structural steel fabrication. The national scope is on the industrial welding services page. Readers comparing states can see industrial welding services in Virginia, the headquarters state, and industrial welding services in Pennsylvania; every Illinois service is on the Illinois hub. Send drawings or photographs, the material and the code and request a quote.

Standards referenced: ASME Boiler and Pressure Vessel Code Section IX (2025 Edition, adopted in 41 Ill. Adm. Code 2120.20) · National Board Inspection Code (NBIC) Part 3 · Boiler and Pressure Vessel Repairer Regulation Act, 225 ILCS 203 · ASME B31.3 · ASME B31.1 · AWS D1.1 Structural Welding Code, Steel · AWS D1.6 Structural Welding Code, Stainless Steel · AWS D18.1 · ASME BPE · API 653 · API 1104 · OSHA 29 CFR 1910.252 · OSHA 29 CFR 1910.272 · NFPA 51B · 32 Ill. Adm. Code 350 (industrial radiography)

Frequently asked questions

Who provides welding services, Chicago plants and buildings included?

Paul Industries provides welding services for Chicago plants, hospitals, universities and commercial buildings, covering steam and process piping, sanitary tube, structural supports, platforms and boiler and vessel repairs. Inside the city, boiler repairs follow the Department of Buildings program; elsewhere in Cook County, the State Fire Marshal’s rules apply. Send drawings or photographs and the code to start.

Who repairs heavy equipment frames and buckets in Peoria and the Quad Cities?

Paul Industries repairs cracked frames, booms, housings and buckets and hardfaces wear parts for plants and fleets in Peoria, East Peoria, Moline, East Moline and Rock Island. Cracks are mapped by magnetic particle or dye penetrant testing, removed and rewelded with preheat matched to the steel, then examined again. Paul Industries also builds fixtures and repairs plant structures at those sites.

Who handles welding during turnarounds at Joliet, Lemont and Wood River refineries?

Paul Industries handles B31.3 piping, exchanger and vessel repairs, tank repairs and structural welding during turnarounds at the Joliet, Lemont and Wood River refineries and at Metro East chemical sites. Procedures and welders are qualified to ASME Section IX before the window opens, and examination is planned with the owner’s inspector so radiography or ultrasonic testing does not hold up the schedule.

Does welding in an Illinois grain elevator or mill need a special permit?

OSHA’s grain handling standard, 29 CFR 1910.272, requires a hot work permit for welding in grain elevators, feed mills, flour mills, dry corn mills and soybean flaking operations, on top of the general welding rules in 29 CFR 1910.252. The permit covers dust cleanup, isolation of openings, a fire watch and checks after the work. Paul Industries works under the plant’s permit system at Illinois grain and ingredient facilities.

Can welding be done outdoors in an Illinois winter?

Welding can be done outdoors in an Illinois winter with the right controls. AWS D1.1 bars structural welding below 0 F ambient unless the welding area is heated and requires base metal below 32 F to be warmed first, while pipe and pressure procedures set their own preheat. Paul Industries uses heated enclosures, recorded preheat and low-hydrogen practice to keep winter welds sound.

Who can weld on an Illinois boiler or pressure vessel?

Illinois treats any organization welding on a boiler or pressure vessel’s pressure-retaining boundary as a repairer under 225 ILCS 203, and the boiler rules require the inspector to accept the welding procedure, the welders and the method before a repair starts. Owners authorized to repair their own equipment follow their own approved program. Paul Industries plans such repairs with the inspector and files the National Board report afterward.

What welding records should an Illinois plant keep?

An Illinois plant should keep the welding procedure specifications and procedure qualification records, welder qualifications and continuity logs, weld maps, material test reports, examination reports and, for pressure equipment, the National Board R-1 or R-2 reports and inspector acceptances. Boiler owners must also keep maintenance records for at least 3 years under the state rules. Paul Industries hands over those records by system.

Is radiography or ultrasonic testing better inside an operating Illinois plant?

Ultrasonic and phased array testing avoid the radiation exclusion zone that radiography needs under the Illinois Emergency Management Agency’s industrial radiography rules, so they suit work beside operating equipment and occupied areas. Radiography still gives a permanent image many owners prefer. B31.3 and B31.1 accept either in many cases, and Paul Industries agrees the method with the owner’s inspector before work.

Who performs orbital sanitary welding for North Shore pharmaceutical plants?

Paul Industries performs orbital GTAW sanitary welding for pharmaceutical, API and biologics plants on the North Shore and in Lake County, with daily weld coupons, borescope inspection, weld maps and passivation before service. Records are organized to feed installation qualification. Send the P&IDs, the BPE or owner specification and the schedule to start.

How is a crack in a machine frame repaired so it does not return?

A lasting crack repair starts by finding why the crack formed, whether fatigue, overload, a poor original weld or a stress raiser, and then mapping its full length by magnetic particle or dye penetrant testing. The crack ends are drilled, the crack is gouged out to sound metal, preheat is applied for the steel grade, and the joint is rewelded and examined. Paul Industries adds reinforcement where the design caused the crack.

What is hardfacing and when do Illinois plants use it?

Hardfacing is welding a wear-resistant alloy onto a part’s working surface so it resists abrasion, impact or both. Illinois ingredient, grain and equipment plants use it on hammer mill parts, conveyor flights, crusher rolls, buckets and liners, choosing chromium carbide alloys for abrasion and manganese or tough alloys for impact. Paul Industries hardfaces new and worn parts and rebuilds the base metal first where needed.

Does Illinois require special inspection for structural welding?

Structural welding on buildings in Illinois follows AWS D1.1 and the special inspection program of the building code adopted by the city or county where the building stands, since Illinois leaves most building code adoption to cities and counties. Plant structures follow the owner’s engineer and specification. Paul Industries welds to the specified code and provides visual and nondestructive examination records for the inspector.

Can tanks be welded while they still hold product in Illinois?

Welding on a tank that holds or held flammable product needs cleaning, gas freeing and testing to safe levels first, or a hot tap procedure designed for the shell and contents. OSFM schedules inspections for hot work on regulated underground tanks under Part 175. Paul Industries plans tank welding with cleaning, atmospheric testing and isolation so the work proceeds safely.

Who performs industrial maintenance welding, Chicago and suburban plants included?

Paul Industries performs industrial maintenance welding for Chicago and suburban plants on a scheduled or call-out basis: worn conveyor and machine parts, cracked guards and frames, leaking utility piping, damaged platforms and supports. Each job is logged with the procedure, the welder and the inspection result, so the plant’s maintenance history shows what was welded. Service agreements can cover recurring outage work.

What does Paul Industries need to quote an Illinois welding job?

To quote an Illinois welding job, Paul Industries needs drawings or photographs of the work, the material and thickness, the governing code, the number of joints or the wear area, access and position, the outage or production window, and the examination required. With that, Paul Industries gives a budget range from comparable jobs and then a firm price once the scope is confirmed.

Who welds stainless food equipment and platforms in Chicago-area food plants?

Paul Industries welds stainless platforms, equipment frames, guards and supports for Chicago-area food, beverage and dairy plants to AWS D1.6, with continuous, ground and passivated welds where the area is washed down. Hygienic design keeps crevices and horizontal ledges out of product zones. Paul Industries fabricates the steel off site and installs it during sanitation windows.

Need code welding or a machinery repair at an Illinois plant?

Send drawings or photographs, the material and thickness, the governing code and the outage window. Call 201-450-8280 or request a quote.