Paul Industries provides industrial welding services in West Virginia for steel and aluminum mills, gas processing plants and compressor stations, Kanawha Valley and Ohio River chemical plants, power stations and manufacturers, welding pipe, structures, equipment and boilers to ASME and AWS codes. Each job comes with qualified procedures, welder records, examination reports and a weld map the owner keeps. Paul Industries is headquartered at 256 Shore Drive, Kilmarnock, Virginia, and takes welding work at plants across West Virginia as field welding, off-site fabrication or complete fabricate-and-install packages.

Request a quote or call 201-450-8280

Headquarters 256 Shore Drive, Kilmarnock, Virginia
New steel capacity Nucor Apple Grove sheet mill, up to 3 million tons a year, shipments expected early 2027
Pipeline compression Mountain Valley Pipeline compressor stations in Wetzel, Braxton and Fayette counties
Boiler repairs NBIC Part 3, adopted by 42 CSR 3 for steam boilers above 15 psi
Hot work State Fire Code built on NFPA 1, 2021 edition (87 CSR 1)
Reviewed November 2026

What do industrial welding services in West Virginia cover?

Industrial welding services in West Virginia cover code pipe welding on process, steam and gas lines; structural welding on platforms, pipe racks, crane runways and building steel; repair welding on mill equipment, chutes, conveyors and machinery bases; weld repairs on boilers and tanks under their inspection codes; and stainless and aluminum work where the product or the plant calls for it. A single outage at a West Virginia plant often needs several of these at once, under different codes, inspected by different people.

The general methods, processes and paperwork are set out on the industrial welding services page. This page covers what changes in West Virginia: the industries that generate the welding, the state rules that touch it, the materials those industries run, and how welding gets scheduled around mill downs, gas plant outages and chemical turnarounds.

Industrial welding, West Virginia industry by industry

Industrial welding in West Virginia follows five industries: steel and aluminum, natural gas, chemicals, electric power and consumer manufacturing. Each brings its own mix of codes, materials and outage patterns, set out in the table below.

Where welding demand sits in West Virginia and what it involves
IndustryWhere in West VirginiaTypical weldingCodes most often applied
Steel and aluminumMason County, Weirton, RavenswoodMill equipment repair, crane runways, structural steel, water and hydraulic pipingAWS D1.1, D1.2, D14.1, ASME B31.3
Gas processing and compressionDoddridge, Wetzel, Marshall, Braxton and Fayette countiesHigh-pressure gas and NGL piping, skids, compressor piping, pipe supportsASME B31.3 inside plants, ASME B31.8 and API 1104 on pipelines and stations
ChemicalsKanawha Valley, Ohio River from Moundsville to ParkersburgAlloy and carbon steel process pipe, vessel nozzles, tank repairsASME Section IX, B31.3, API 653
Electric powerOhio and Kanawha river stations, gas-fired plantsBoiler tube and header repairs, high-energy piping, ash and coal handlingASME Section I, B31.1, NBIC Part 3
Consumer and light manufacturingMartinsburg, Morgantown, Fairmont, HuntingtonStainless product lines, equipment frames, utility pipingASME B31.3, AWS D1.6, owner hygienic specifications

Steel and aluminum mills from Weirton to Ravenswood and Apple Grove

West Virginia’s metals industry is being rebuilt as much as repaired. Nucor is completing an electric arc furnace sheet mill at Apple Grove in Mason County, designed for up to 3 million tons of sheet steel a year, with commercial shipments expected in early 2027. In the Northern Panhandle, Cleveland-Cliffs indefinitely idled its Weirton tinplate operation in April 2024. On the Ohio River at Ravenswood, the rolling mill built by Kaiser Aluminum in 1957 has run under Constellium since 2011, producing aluminum plate including armor plate for military vehicles.

Mill welding is heavy, repetitive and tied to scheduled downs: roll stands, mill housings, scale pits, conveyors, cooling beds, crane runways and the water and hydraulic systems that serve them. Crane and runway work follows AWS D14.1 and D1.1, while process water, hydraulic and oxygen lines follow B31.3 with the cleanliness the service needs. Paul Industries plans mill work against the down schedule, with replacement parts fabricated and fit-checked before the line stops.

Gas processing plants and compressor stations

Natural gas brings welding at every stage from wellpad to transmission line. West Virginia ranked fifth among the states for marketed gas production in 2023, and the Mountain Valley Pipeline, placed in service on June 14, 2024, starts in Wetzel County and runs 303 miles to southern Virginia, with West Virginia compressor stations in Wetzel, Braxton and Fayette counties. Processing plants inside the fence are commonly welded to B31.3, while pipeline and station piping follow B31.8 and API 1104 under the federal pipeline safety rules. Pipe welding West Virginia gas plants specify often includes impact-tested procedures for lines that chill when liquids flash, and low-hydrogen practice on thick, high-strength fittings.

Welding, Charleston, WV and the Kanawha Valley

Welding Charleston, WV chemical plants schedule centers on turnarounds and maintenance at long-established sites in South Charleston, Institute and Belle. The work includes carbon steel, stainless and nickel alloy process pipe, vessel nozzle and support repairs, tank floor and shell repairs under API 653, and steel for new equipment. Most of these plants operate processes covered by OSHA process safety management, so welding is tied to hot work permits, management of change and the plant’s mechanical integrity records. Welders in Charleston, WV chemical plants qualify to the procedures the owner’s specification names, and the qualification records stay in the job file.

Power stations and Ohio River plants

Power generation brings boiler tube, header and high-energy piping work. West Virginia is the second-largest coal producer in the country after Wyoming, and coal-fired stations along the Ohio and Kanawha rivers run steam boilers far above the 15 psi line where the state boiler rule begins. Tube and header repairs follow ASME Section I and the National Board Inspection Code, and high-energy piping follows B31.1. Welding Huntington, WV and welding Parkersburg, WV plants schedule for Ohio River outages mixes this boiler work with chemical, metals and terminal repairs, often inside the same few weeks of spring and autumn.

Morgantown, Fairmont and the Eastern Panhandle

North central and eastern West Virginia bring lighter, cleaner welding. Welding Morgantown, WV research buildings and hospitals need tends toward laboratory gas and utility piping, steam and condensate in central plants, and structural steel for building additions. In Berkeley County, consumer products plants such as Procter and Gamble’s Tabler Station run stainless product and liquid raw material lines where weld quality is judged by cleanability as well as strength.

Which welding codes apply to West Virginia plant work?

Welding codes at West Virginia plants are set by the item being welded: ASME Section IX qualifies procedures and welders for pressure work under the B31 piping codes and the boiler and vessel codes, AWS D1.1, D1.2 and D1.6 govern structural welding in steel, aluminum and stainless, and API 1104 governs pipeline welding. On any given job, the owner’s specification, the construction code for the item and, for steam boilers, the state boiler rule decide which of these applies.

Welding codes, qualification and inspection by type of work in West Virginia
WorkConstruction codeQualificationWho reviews it
Process and utility pipe in plantsASME B31.3ASME Section IX WPS, PQR and welder qualificationOwner’s inspector under the plant’s integrity program
Boiler tubes, headers and external pipingASME Section I, B31.1, NBIC Part 3 for repairsASME Section IXAuthorized inspector, with the Division of Labor’s permit cycle
Gas pipelines and compressor station pipingASME B31.8, 49 CFR Part 192API 1104 or ASME Section IX as Part 192 allowsPipeline operator under federal pipeline safety rules
Building and platform steelAWS D1.1 under the 2018 IBC where enforcedAWS D1.1 prequalified or qualified proceduresSpecial inspector where the building official requires one
Aluminum structures and equipmentAWS D1.2AWS D1.2 procedure and welder testsOwner’s inspector
Mill cranes and runwaysAWS D14.1AWS D14.1 or D1.1Owner’s crane inspection program
Atmospheric storage tank repairsAPI 653, API 650ASME Section IXAuthorized tank inspector and the owner

Weld repairs on high-pressure steam boilers under 42 CSR 3

Weld repairs on West Virginia steam boilers above 15 psi follow the National Board Inspection Code, Part 3, which the Division of Labor’s rule 42 CSR 3 adopts by reference along with ASME Section I. The rule defines a repair as the work needed to restore a boiler to safe operating condition, as further defined in NBIC Part 3, and an inspection can include examining the boiler after repairs or alterations. In practice the inspector is consulted before a welded repair, accepts the method, and reviews the finished weld and its pressure test before the boiler returns to service. Paul Industries plans boiler repairs around that review and the permit cycle covered on the boiler repair in West Virginia page.

Hot work rules before welding at a West Virginia plant

Hot work at West Virginia plants answers to two sets of rules: OSHA’s welding and cutting standard, 29 CFR 1910.252, which federal OSHA enforces at private workplaces across the state, and the West Virginia State Fire Code, rule 87 CSR 1, which is built on the 2021 edition of NFPA 1. NFPA 1 carries hot work requirements drawn from NFPA 51B: a written permit, combustibles moved or shielded, a trained fire watch during and after the work, and checks of the area before the permit is closed.

Chemical and gas plants add their own layers: gas testing before and during the work, isolation of drains and sewers, and limits on hot work near units that are running. Paul Industries works under the owner’s permit system and keeps the permit, gas test and fire watch records with the welding file.

Structural welding and special inspection in West Virginia

Structural welding on West Virginia building projects follows AWS D1.1 for steel, and where a county or municipality enforces the State Building Code, the 2018 International Building Code’s Chapter 17 calls for special inspection of structural welding. Rule 87 CSR 4 adopts the 2018 IBC for the state, and each jurisdiction that adopts the State Building Code is responsible for enforcing it. Inside plants, platforms, pipe racks and equipment supports are often governed by the owner’s structural specification, which usually points to D1.1 as well. Fabricated steel for these jobs is described on the structural steel fabrication page.

Cold weather and wind on West Virginia field welds

Cold, wet and windy conditions on West Virginia ridgetops and river valleys change how field welds are made from late autumn into spring. AWS D1.1 forbids structural welding when the ambient temperature is below 0 degrees Fahrenheit, or when surfaces are wet or exposed to rain, snow or high wind, unless the welder and the work are protected. Pressure piping codes and the owner’s procedures set preheat by material and thickness, and cold steel that would need no preheat in summer is warmed in winter to drive off moisture and slow the cooling rate.

Wind is the quieter problem. Gas metal arc and gas tungsten arc welding rely on a shielding gas that a breeze strips away, leaving porosity that shows up later on radiographs. On exposed gas plant pads and mill roofs, Paul Industries builds wind shelters and heated enclosures around the joint, uses heating blankets or induction for preheat and post-weld heat treatment, and keeps low-hydrogen electrodes in heated ovens until use. Those steps are written into the procedure and the job plan, so a January tie-in on a ridgetop meets the same acceptance standard as a weld made in a fabrication bay.

Steep terrain also shapes the work. Many gas plants and compressor stations sit on graded pads reached by narrow roads, so welding rigs, materials and examination equipment are staged to fit the access, and long spool runs are split where the route needs it.

Industrial vs commercial welding at a West Virginia plant

Industrial vs commercial welding differs mostly in what the weld has to prove. Commercial welding on building steel, stairs and handrails is accepted on visual inspection and the building code’s special inspection. Industrial welding on pressure piping, boilers, mill equipment and tanks carries qualified procedures, traceable materials, examination by volumetric or surface methods, and records that become part of the plant’s integrity program. A West Virginia plant usually needs both under one schedule, and one set of records is easier to keep than several.

Pipe welding West Virginia gas and chemical lines demand

Pipe welding on West Virginia gas and chemical lines covers carbon steel, low-temperature carbon steel, stainless steel and nickel alloys, each with its own procedure, filler and heat input limits. Natural gas liquids lines need procedures impact tested at the lowest temperature the line can reach, because liquids flashing through a valve chill the pipe well below ambient. Stainless and nickel alloy welds get an inert gas purge to protect the root, and chlorine and caustic lines at Ohio River plants follow the owner’s material rules, including stress relief where hot caustic service calls for it. Detail on the piping these welds go into is on the process piping in West Virginia page, and pickling and passivation after stainless welding on the passivation services in West Virginia page.

Aluminum welding at West Virginia rolling and metals plants

Aluminum welding at West Virginia metals plants follows AWS D1.2 for structures and the owner’s specification for equipment. Aluminum conducts heat away from the joint quickly, forms a tough oxide film that has to be removed just before welding, and loses strength in the heat-affected zone of heat-treated alloys, so procedures control cleaning, preheat, filler alloy and torch speed closely. Gas metal arc welding with pulsed current handles most structural and equipment work, and gas tungsten arc welding handles thin sections and repairs.

How is welding done at an operating West Virginia plant?

Welding at an operating West Virginia plant is done either inside a planned outage, with the system isolated, drained and gas free, or on equipment that stays in service, under procedures written for that condition. Welding onto a pressurized gas or liquid line, for a hot tap or a sleeve, needs measured wall thickness, confirmed flow, and a procedure qualified for in-service welding, such as the in-service annex of API 1104 on pipelines. Paul Industries prefabricates sleeves, nozzles and replacement spools before the window opens, so outage time goes to fit-up, welding and examination.

Weld examination and the records a West Virginia owner keeps

Weld examination at West Virginia plants uses visual inspection on every weld and adds surface or volumetric methods as the code, the fluid service and the owner require. The choice of method in a running plant also depends on what else is happening in the unit, because radiography needs an exclusion zone around the work.

Weld examination methods and how they fit West Virginia plant work
MethodWhat it findsWhere it fitsRecord produced
Visual examinationSurface defects, profile, undercut, sizeEvery weld, before any other methodInspection report against the weld map
Liquid penetrantSurface cracks in any metalStainless, nickel alloy and aluminum weldsReport with procedure and acceptance
Magnetic particleSurface and near-surface cracks in carbon steelMill equipment, crane runways, structural weldsReport with technique and indications
RadiographyPorosity, slag, lack of fusion in the weld volumePipe in outages or shop fabrication with clear exclusion zonesFilm or digital images with interpretation
Ultrasonic and phased arrayLack of fusion and cracks in thick sectionsRunning plants where radiography would clear an area, heavy wall pipeScan files and report
Pressure testLeaks across the completed systemPipe, boilers and vessels before serviceSigned test record with gauge calibration

The welding file Paul Industries hands over holds the procedure specifications and qualification records, welder continuity logs, material certificates, the weld map, examination reports, heat treatment charts where stress relief was done, and pressure test records. Owners keep that file with the plant’s mechanical integrity records, and it is the first thing an inspector asks for after an incident.

What do industrial welding services in West Virginia cost?

Industrial welding services in West Virginia are priced on the code and examination level, the material, the access, the outage window and the number of shifts, more than on hours alone. Alloy and stainless welds with purge, preheat and stress relief cost several times carbon steel structural welds of the same size, and work inside a short mill down or gas plant outage carries premium shift patterns. Radiography or phased array examination, procedure qualification for an unusual material, and fire watch and gas testing time all add identifiable cost.

Winter work adds heated enclosures, preheat equipment and slower production on exposed sites, and remote gas pads add staging time for rigs and materials. Repair work that starts with an unknown, such as a cracked mill housing or a thinned boiler tube, is priced in two steps: an assessment with examination and a repair plan, then the repair itself once the extent of the damage is measured. That approach keeps the owner from paying a contingency for damage that turns out smaller than feared.

State law adds a threshold to watch: the West Virginia Contractor Licensing Act, W. Va. Code 30-42, applies to commercial construction, alteration and repair work costing $25,000 or more. Paul Industries offers a budget range from comparable scope at the start, then a firm price once drawings, materials and the outage plan are defined.

Who provides industrial welding services in West Virginia?

Paul Industries provides industrial welding services in West Virginia, covering code pipe, structural, mill, aluminum, stainless and boiler repair welding with the procedures, examination and records each job requires. Among welding companies in West Virginia, Paul Industries carries a job from fabrication through installation and testing under one contract, so pipe, steel and equipment welds share one schedule and one file. The company, headquartered in Kilmarnock, Virginia after earlier years in northern New Jersey and Pennsylvania, takes welding work throughout West Virginia, in all 50 states and abroad. The headquarters state is covered on the industrial welding services in Virginia page, with neighboring states on the Pennsylvania and Maryland pages and the region on the East Coast page.

Owners comparing welding contractors West Virginia plants use often weigh the paperwork as heavily as the welding. Paul Industries welds to the owner’s specification, qualifies procedures and welders to the code named, and documents every weld so the integrity program receives complete records. Related work on vessels and tanks is on the pressure vessel fabrication in West Virginia and tank fabrication in West Virginia pages, and on generating stations under power generation.

Industrial welding from Paul Industries across West Virginia

Paul Industries delivers welding services West Virginia plants depend on, from mill repairs at Apple Grove and Ravenswood to gas plant tie-ins in the north central counties, chemical turnarounds in the Kanawha Valley and stainless work in the Eastern Panhandle. Industrial welding WV owners order comes as field welding, off-site fabrication or complete fabricate-and-install packages, with the welding file delivered at turnover. Welding West Virginia plants schedule is planned around their outages, and more on the state sits on the West Virginia page. Send drawings, materials and dates, call 201-450-8280 or request a quote.

Standards referenced: ASME Boiler and Pressure Vessel Code Section IX · ASME B31.3 Process Piping · ASME B31.1 Power Piping · ASME B31.8 · National Board Inspection Code Part 3 · AWS D1.1 Structural Welding Code, Steel · AWS D1.2 Structural Welding Code, Aluminum · AWS D1.6 Structural Welding Code, Stainless Steel · AWS D14.1 · API 1104 · API 653 · NFPA 1 Fire Code (2021) and NFPA 51B · OSHA 29 CFR 1910.252 · W. Va. Code 21-3-7 and 42 CSR 3 · 87 CSR 1 (West Virginia State Fire Code) · 87 CSR 4 (West Virginia State Building Code) · W. Va. Code 30-42 (West Virginia Contractor Licensing Act)

Frequently asked questions

Who handles custom welding Charleston, WV plants order, such as platforms, guards and equipment frames?

Paul Industries fabricates and installs platforms, stairs, guards, equipment frames, pipe supports and chutes for Charleston area plants, measured on site and welded to AWS D1.1 or the owner’s specification. Assemblies are built off site where possible, galvanized or coated as specified, and fitted during planned stops so hot work inside the plant stays short.

Does Paul Industries take mill and plant welding in Hancock and Brooke counties around Weirton?

Yes. Paul Industries takes welding work at metals, chemical and manufacturing plants in Hancock, Brooke, Ohio and Marshall counties, including mill equipment repair, crane runway work, structural steel and process piping. Work is planned against the plant’s down schedule, with replacement parts fabricated and fit-checked beforehand.

Who welds at Ohio River plants around Parkersburg, Ravenswood and Huntington?

Paul Industries welds at chemical, aluminum, power and terminal sites along the Ohio River from Parkersburg and Ravenswood down to Huntington, covering alloy process pipe, boiler tube and header repairs, aluminum structures and tank repairs. Outage welding in this corridor often clusters in spring and autumn, so Paul Industries plans procedures, materials and examination early.

Does Paul Industries handle welding Morgantown, WV research buildings and hospitals need?

Yes. Paul Industries welds laboratory gas and utility piping, central plant steam and condensate lines, chilled water headers and structural steel for additions in Morgantown, Fairmont and Clarksburg. Work in occupied buildings runs under hot work permits, fire watch and infection control or laboratory safety rules, with welding fumes and sparks controlled at the work area.

How do welding companies in West Virginia document a welder's qualification?

For pressure work, a welder is qualified by testing to a welding procedure under ASME Section IX, and the record lists the process, positions, materials and thickness range covered. Qualification stays current while the welder uses the process at least once every six months, and a continuity log records that use between tests. Structural welders qualify under AWS D1.1 or D1.2, and pipeline welders under API 1104.

How does the Contractor Licensing Act treat welding contractors West Virginia plants use?

Under W. Va. Code 30-42, the state’s Contractor Licensing Act, whether a job counts as contracting depends on the cost of the undertaking, $25,000 or more for commercial work, and sets out trade classifications such as piping contractor. Welding that forms part of construction, alteration or repair at a plant is measured against those definitions, and Paul Industries scopes each job with the classification in view.

Who approves a welded repair on a high-pressure steam boiler in West Virginia?

The boiler’s inspector, an inspector of the Division of Labor or a special inspector of the insurer, reviews welded repairs under NBIC Part 3, which rule 42 CSR 3 adopts. The inspector accepts the repair method before work, examines the completed repair and witnesses the pressure test, and the repair report goes into the boiler’s records.

What hot work permit does a West Virginia plant need before welding?

The plant issues its own written hot work permit under OSHA 29 CFR 1910.252 and the State Fire Code’s NFPA 1 requirements, naming the location, the work, the precautions taken and the fire watch. Chemical and gas plants add gas testing and isolation of drains and openings. Paul Industries works under the owner’s permit and files each permit with the welding records.

When does structural welding on a West Virginia building need special inspection?

Where a county or municipality enforces the State Building Code, the 2018 International Building Code requires special inspection of structural steel welding as set out in its Chapter 17, with the inspector reporting to the building official. Projects in jurisdictions without enforcement still follow AWS D1.1 and the owner’s inspection plan.

How are welding procedures qualified for cold NGL lines at a gas processing plant?

Under ASME B31.3, a procedure for low-temperature service is qualified with impact tests on the weld metal and heat-affected zone at or below the minimum design temperature. Heat input is then held within the qualified range during production welding, and the filler metal is chosen for toughness at that temperature. The records go into the line’s turnover package.

How is stainless pipe welded in a running Eastern Panhandle consumer products plant?

Stainless lines are cut and prefabricated off site, then installed during planned line stops with hot work permits and the production area protected. Root passes are made with an inert gas purge, often by orbital welding on tube, and welds are inspected inside where the owner requires it. Pickling or passivation follows where the hygienic specification calls for it.

How is aluminum welded at a West Virginia rolling mill?

Aluminum is cleaned of oil and oxide just before welding, often preheated on thick sections, and welded by pulsed gas metal arc or gas tungsten arc with a filler alloy matched to the base metal and service. Heat input is limited to protect the strength of heat-treated alloys. Structural welds follow AWS D1.2.

How is welding scheduled around a steel mill down?

The scope is fixed weeks before the down, replacement parts are fabricated and fit-checked, and procedures and welders are qualified in advance. During the down, welding runs on continuous shifts with examination close behind, so defects are found while the area is still open. Paul Industries closes out with the welding file before the mill restarts.

What does welding at a West Virginia compressor station involve?

Compressor station piping is welded to ASME B31.8 and 49 CFR Part 192, the federal pipeline safety regulation, with each procedure and welder qualified under API 1104 or ASME Section IX. Nondestructive testing covers a share of welds set by the regulations, and tie-ins to operating lines are planned with the operator’s blowdown and purge procedures.

Which welded assemblies does Paul Industries fabricate off site for West Virginia plants?

Paul Industries fabricates pipe spools, pipe rack modules, skids, platforms, stairs, equipment frames, chutes, hoppers, wear liners and replacement mill components off site, examined and documented before delivery. Plants take them as supply-only items for their maintenance teams or as part of a complete installation.

Which documents close out a welding job at a West Virginia plant?

The close-out file holds welding procedure specifications and their qualification records, welder qualifications and continuity logs, material certificates, a weld map, examination reports, any heat treatment charts and pressure test records. Boiler repairs add the repair report accepted by the inspector, and tank repairs add the API 653 records.

Does a weld repair on a West Virginia storage tank change its inspection records?

Yes. A weld repair on a tank built to API 650 is made and documented under API 653, with the repair recorded in the tank’s inspection history, and tanks regulated under the state’s Aboveground Storage Tank Act carry their own records with the Department of Environmental Protection. Paul Industries provides the repair records for both.

Which details does Paul Industries need to price welding at a West Virginia plant?

Send drawings or photos, materials and thicknesses, the applicable code and examination requirements, the plant’s hot work and access rules, and the outage or down dates. For repairs, add the inspection finding or failure history. Paul Industries replies with a budget range, then fixes the price when the scope is settled.

Planning welding work at a West Virginia plant or mill?

Send drawings or photos, the materials and code, the examination level and the down or outage window. Call 201-450-8280 or request a quote.