Paul Industries provides pressure vessel fabrication in Pennsylvania for chemical, pharmaceutical, natural gas, food and power plants, designing and building ASME Section VIII vessels to Pennsylvania’s boiler and pressure vessel statute and the L&I regulations in Chapter 3a of Title 34. Paul Industries designs, fabricates, supplies, installs, tests and repairs receivers, separators, reactors, columns, heat exchanger shells and jacketed process vessels. Pennsylvania adds its own marking, inspection and installation rules to the ASME Code, and this page sets out what they mean for an owner ordering a vessel.

Request a quote or call 201-450-8280

Headquarters 256 Shore Drive, Kilmarnock, Virginia
Construction code ASME Section VIII or X for vessels installed in PA (34 Pa. Code 3a.71)
State marking Keystone serial number at least 5/16 in. high (3a.21)
Inspection cycle Every 36 months by a commissioned inspector (3a.111)
Gas production Pennsylvania ranks second in the US, after Texas (EIA)
Reviewed November 2026

What does the Pennsylvania pressure vessel code require before a vessel runs?

The Pennsylvania pressure vessel code, Chapter 3a of Title 34, requires that an unfired pressure vessel installed in the state be built to ASME Section VIII or, for fiber-reinforced plastic vessels, Section X, carry the ASME symbol, the manufacturer’s data and a National Board registration number, carry a Pennsylvania serial number made of the keystone symbol and figures, and pass an inspection by a commissioned inspector before it operates. A certificate of operation follows the inspector’s report.

The keystone number is the step owners outside the state most often miss. It is required on new boilers and unfired pressure vessels installed in Pennsylvania, in figures at least five sixteenths of an inch high, and like the ASME stamping it must stay exposed rather than painted or lagged over. Vessels built to a Pennsylvania special number under section 7(b) of the Act, rather than the ASME Code, are a narrow exception that the Department approves case by case.

The national pressure vessel fabrication page explains ASME design, materials, welding and testing. This page covers what Pennsylvania layers on top, how the state’s industries use vessels, and what an owner receives with a vessel destined for a Pennsylvania plant.

How the Pennsylvania rules fit together

Pennsylvania splits vessel regulation between the equipment rules and the building rules. The Pennsylvania Boiler and Unfired Pressure Vessel Law (35 P.S. 1331.1 to 1331.19) and Chapter 3a govern the vessel itself: construction code, marking, installation, inspection, repair and accidents. The Uniform Construction Code governs the building, and under 34 Pa. Code 403.48 no UCC permit is needed to install, repair or replace a vessel, though foundations, platforms and openings in the building still follow the UCC.

Pennsylvania requirements that shape a new pressure vessel
RequirementSourceWhat the owner needs from the fabrication
ASME Section VIII or X construction34 Pa. Code 3a.71Design calculations, drawings and a Manufacturer’s Data Report for the code used
ASME symbol and National Board number3a.21Nameplate data matching the data report, with the National Board number
Keystone serial number3a.21Space on the nameplate or shell for the Pennsylvania number, kept clear of insulation
Clearances of 18 in. at front, rear and sides, 30 in. at a manholeL&I Boiler DivisionA layout that meets them, or a variance petition prepared before delivery
Inspection before useChapter 3aAccess for the inspector, the data report on site and a nameplate that can be read
Periodic inspection every 36 months3a.111Manways, inspection openings and drains that make internal inspection practical
Relocation notice within 10 days3a.97Records kept with the vessel so a future move can be filed quickly

A vessel that meets the clearances can be set without asking the Boiler Division first, but it still may not operate until it has been inspected. Where a tight equipment room or mezzanine cannot give the clearances, the owner petitions the Industrial Board for a variance. Paul Industries checks the room against the clearance figures while the general arrangement drawing is still a sketch, so nozzle orientation and manway placement solve the problem rather than a petition.

Which PA unfired pressure vessel types are exempt?

A PA unfired pressure vessel is exempt from Boiler Division inspection when it falls in one of the categories the Department lists, which include vessels at or below 15 psi with approved safety devices, small vessels up to 5 cubic feet at 250 psi or 3 cubic feet at 350 psi, vessels of 6 inches inside diameter or less, water-containing vessels of 120 gallons or less, and water filters and softeners up to 120 gallons and 100 psi at ambient temperature. Air-conditioning heat exchangers up to 300 psi and 210 degrees Fahrenheit, vessels built and run under U.S. Department of Transportation rules, and vehicle air tanks are also outside the program.

Exemption from state inspection does not change how the vessel should be built. A 4-cubic-foot air receiver at 200 psi still needs an ASME design, a relief valve sized for its sources and a nameplate the maintenance team can read, and an exempt vessel can still fall under the UCC or the owner’s insurer. Paul Industries builds exempt vessels to the same ASME standard as inspected ones, which keeps the records consistent and the vessel saleable if the plant ever changes hands.

What is an unfired pressure vessel, and when does a tank become a pressure vessel?

An unfired pressure vessel is a closed container that holds a gas, vapor or liquid above atmospheric pressure from a source outside the vessel, such as a compressor, pump or steam supply, rather than from direct firing as in a boiler. Receivers, separators, reactors, filter housings, heat exchanger shells and autoclaves are all unfired pressure vessels, and Chapter 3a has its own sections for steam and hot water heat exchangers and for autoclaves and quick-opening vessels.

When does a tank become a pressure vessel? A tank becomes a pressure vessel when its design pressure exceeds the limits of the atmospheric or low-pressure tank standards and it falls within ASME Section VIII scope, which generally begins above 15 psi. A storage tank that is blanketed with nitrogen, pressurized for transfer or connected to a pressure source without adequate relief can cross that line in service, which is why the design pressure, the relief path and the code are settled together. Atmospheric tanks for Pennsylvania sites are covered under tank fabrication in Pennsylvania.

Pressure vessels in Pennsylvania’s process industries

Pressure vessels in Pennsylvania serve a wider spread of industries than in most states, because the Commonwealth combines a large pharmaceutical and biotech base in the southeast, a natural gas industry that ranks second in the nation after Texas according to the EIA, legacy chemical and metals plants in the west, and food and agricultural processing through the central counties. Each brings its own vessel types, materials and inspection habits.

Pressure vessel demand by Pennsylvania industry and region
Industry and regionTypical vesselsMaterials and design points
Natural gas and NGLs, western and northern tier, Delaware RiverInlet separators, slug catchers, filter separators, dehydration contactors, fractionation and splitter columns, NGL storage bulletsCarbon steel with impact testing for low temperatures, corrosion allowance for wet gas, Division 2 for large high-pressure units
Petrochemicals and plastics, Beaver County and the Ohio ValleyReactors, flash drums, knockout drums, purge and degassing vesselsCarbon and low-alloy steels, thick sections, PWHT where the code or service requires
Pharmaceutical and biotech, Philadelphia suburbs and the King of Prussia corridorJacketed reactors, bioprocess vessels, WFI and clean steam vessels, autoclave chambers316L stainless, polished and passivated surfaces, ASME BPE fittings, full vacuum rating
Specialty chemicals, Lehigh Valley and Pittsburgh regionReactors, receivers, condensers, scrubber vesselsStainless and higher alloys for corrosive service, clad plate for large shells
Food, dairy and beverage, Lancaster, York, Reading and HarrisburgCookers, retorts, CO2 and air receivers, hot water and steam heat exchangersStainless contact surfaces, jackets for steam or glycol, sanitary design where product touches
Utilities and power, statewideAir receivers, blowdown tanks, deaerator shells, feedwater heatersCarbon steel, relief sized for every source, inspection openings for the 36-month cycle

Natural gas liquids show the scale of the market. At Marcus Hook, on the Delaware River, a refinery site that dates to 1902 now operates as a natural gas liquids hub with an ethane and propane splitter, chilling and refrigerated storage, a fractionator and six tanks holding about 3 million barrels of propane, ethane and butane, supplied by pipeline from western Pennsylvania. In Beaver County, an ethane cracker in Potter Township began operating in November 2022. Facilities of that kind depend on columns, drums and separators built to Section VIII, along with the many smaller vessels that support them.

Pressure vessel fabrication, Pittsburgh to Philadelphia: how the build runs

Pressure vessel fabrication for a Pennsylvania site, from Pittsburgh to Philadelphia, runs through the same ASME sequence as anywhere else, with the state’s marking and inspection steps inserted where they belong. Paul Industries plans each step with the owner’s engineer and the receiving inspector in mind, so the vessel arrives with the records Pennsylvania asks for.

  1. Data sheet review. Design pressure and temperature, minimum design metal temperature, contents, corrosion allowance, nozzle schedule, supports and any Section VIII Division 2 or BPE requirements are confirmed in writing.
  2. Design and drawings. Shell and head thickness, nozzle reinforcement, wind and seismic loads for outdoor vessels, and lifting lugs are calculated. The nameplate location and the space for the keystone number are shown on the drawing.
  3. Material receipt. Plate, pipe and forgings are checked against their mill test reports and ASME Section II specifications, and impact tests are arranged for low-temperature service.
  4. Welding and examination. Procedures and welders are qualified under ASME Section IX; radiography or ultrasonic examination follows the joint category and efficiency used in the design.
  5. Heat treatment and testing. Post-weld heat treatment where the code or the service demands it, then the hydrostatic or pneumatic test witnessed by the authorized inspector.
  6. Finishing. Pickling and passivation of stainless vessels, surface finish checks for product-contact surfaces, coating of carbon steel and protection of nozzles for shipping.
  7. Turnover. The Manufacturer’s Data Report, nameplate rubbing or photo, material and examination records, test charts and relief valve data are handed over for the Pennsylvania inspection.

Stainless vessels for pharmaceutical and food plants often need finishing work that continues into the field, and passivation services in Pennsylvania cover the treatment of vessel interiors and connected piping after installation. Welding of nozzles, supports and connecting spools at the site is described under industrial welding services in Pennsylvania.

PA pressure vessel inspection after installation

PA pressure vessel inspection starts with the inspection before first use and continues every 36 months under 34 Pa. Code 3a.111, with an internal inspection whenever the inspector requires one because of age or condition. A Pennsylvania pressure vessel inspection is made by a holder of a current Pennsylvania Inspector Commission, who works for an insurance company authorized to insure boilers in Pennsylvania, an owner-user authorized to inspect its own equipment, or the Commonwealth. The certificate of operation follows the inspector’s report and payment of the certificate and inspection fees.

Design choices made at fabrication decide how painful those inspections are. A vessel with a manway, inspection openings at the bottom head, a drain at the true low point and a nameplate on a standoff clear of the insulation can be opened, cleaned and examined in a normal outage. A vessel without those features may need insulation removed, scaffolding built or ultrasonic thickness readings taken from outside at many points. Paul Industries designs for the 36-month cycle the vessel will live with.

Vessels in a process covered by OSHA’s process safety management standard also fall under its mechanical integrity element, which expects written inspection and testing procedures for pressure vessels and documented results. The fabrication records Paul Industries supplies become the baseline those programs measure against.

Repairs, rerates and relocated vessels under the PA pressure vessel code

The PA pressure vessel code treats a repair on an existing vessel the same way it treats a boiler repair: the owner consults an inspector before any repair that affects working pressure or safety, the work follows the National Board Inspection Code, and welded repairs and alterations are made by an organization holding a National Board R stamp and documented on a National Board R-1 report or the Department’s own welded repair record. A rerate to a higher pressure or temperature is an alteration and needs new calculations and, usually, a new pressure test.

Relocated vessels have their own rule. Under 3a.97, the owner notifies the Department of the new location within 10 days and the vessel may not enter service until a Department inspection passes it. A used vessel bought at auction or moved from another plant needs its original data report, a check of its thickness against the design minimums and a relief review for its new service. Paul Industries assesses used and existing vessels, repairs and rerates them, and fabricates a replacement when the numbers favor new.

Stainless bioprocess vessels for southeastern Pennsylvania plants

Stainless bioprocess vessels for southeastern Pennsylvania plants combine two rulebooks: ASME Section VIII for the pressure boundary and ASME BPE for the surfaces, welds and fittings that touch product. A buffer hold vessel or media preparation tank in a Montgomery or Chester County facility is usually rated for full vacuum as well as positive pressure, because steam sterilization followed by cooling pulls a vacuum that an unrated shell cannot survive.

Product-contact details drive the work: interior surface roughness specified as a maximum Ra and often electropolished, orbital welds on nozzles and ports with borescope records, sloped bottoms and drainable nozzles so the vessel empties completely, spray devices sized for full coverage during cleaning, and sanitary clamp or BPE flange connections. Each detail adds documentation that the validation team will later rely on. Paul Industries builds those vessels with the weld maps, surface finish readings and material certificates in one turnover package, and builds the cleaning and sterilizing connections that serve them as part of the same scope.

Outdoor vessels and low design temperatures in Pennsylvania

Outdoor vessels in Pennsylvania need a minimum design metal temperature that reflects the coldest conditions at the site, plus any colder temperature the process can create, such as autorefrigeration when liquefied gas flashes during depressurization. The minimum design metal temperature decides whether carbon steel parts need impact testing under the ASME Section VIII rules or can rely on the exemption curves for their material and thickness.

Northern tier gas sites, Erie and the higher ground of the Alleghenies see colder winters than the southeastern counties, so a design copied from a Philadelphia project may not suit a Susquehanna or Tioga County separator. Paul Industries sets the design temperature with the owner from site data and process upsets, then selects plate, forgings and bolting to match, so the nameplate rating holds on the coldest morning of the year.

Delivery and setting at Pennsylvania sites

Delivery and setting at Pennsylvania sites is planned at the drawing stage, because diameter, length and weight decide the shipping route, the crane and the way the vessel enters the building. Large shells may be shipped in sections and joined in the field, which then needs field welding, examination and a field pressure test witnessed by the inspector. Vessels set inside operating plants need rigging paths, floor loading checks and openings that the building team can approve under the UCC.

Paul Industries plans the lift, the setting and the anchor bolts with the foundation design, then aligns, levels and grouts the vessel and connects it to the plant. The receiving inspection, insulation, nameplate standoffs and the inspector’s visit are scheduled before startup rather than after it.

How much does pressure vessel fabrication in Pennsylvania cost?

The cost of pressure vessel fabrication in Pennsylvania is driven by weight and material, design pressure and temperature, the code division, the number and size of nozzles, examination and heat treatment requirements, internal finish, jackets and internals, and the delivery and setting plan for the site. A carbon steel air receiver and a polished 316L jacketed reactor of the same volume can differ in price by several times, because the reactor adds alloy, jacket fabrication, finishing and documentation.

What moves the price of a Pennsylvania pressure vessel
DriverLower costHigher cost
MaterialCarbon steel, standard plate316L, duplex or nickel alloys; clad plate; impact-tested steels
Code and examinationDivision 1 with spot radiographyFull radiography, Division 2 design, PWHT
Surface and finishMill finish, painted exteriorMechanically polished and electropolished interiors, passivation records
AttachmentsFew nozzles, simple saddlesJackets, agitator mounts, internals, skirts with access openings
Site settingGround-level pad with crane accessSetting inside a building, through a wall opening or onto a structure in an operating plant

Paul Industries prices from the data sheet: a budget figure from comparable vessels when the data sheet is preliminary, and a firm price once design conditions, materials, nozzles and finish are fixed. Pressure vessel fabricators PA owners compare should be measured on the same data sheet, and Paul Industries quotes against the owner’s sheet line by line so the comparison is clean.

Who provides pressure vessel fabrication in Pennsylvania?

Paul Industries provides pressure vessel fabrication in Pennsylvania for chemical, pharmaceutical, natural gas, petrochemical, food and utility owners statewide. Headquartered at 256 Shore Drive in Kilmarnock, Virginia, and formerly based in Pennsylvania, Paul Industries now delivers vessels and vessel repairs across the Commonwealth, in all 50 states and to plants abroad through its international work.

Vessels rarely arrive alone, and the connected scope stays under the same contract. Paul Industries installs the connecting lines described under process piping in Pennsylvania, repairs the boilers that feed steam-heated vessels through boiler repair in Pennsylvania, and documents installation and operation for regulated plants under validation and commissioning in Pennsylvania. Outside the Commonwealth, the same work is described for the headquarters state as pressure vessel fabrication in Virginia and for New Jersey as pressure vessel fabrication in New Jersey. Paul Industries works for chemical manufacturing and oil and gas owners nationwide.

Pressure vessel work from Paul Industries in Pennsylvania

Paul Industries designs, fabricates, supplies, installs, tests, repairs and rerates ASME pressure vessels for Pennsylvania plants, with the keystone marking space, inspection access and turnover records the Pennsylvania rules expect. Send the data sheet or a sketch with contents, design pressure and temperature, volume, nozzle list, material and finish, and the site conditions for delivery and setting. Call 201-450-8280 or request a quote. For the wider range of process, water and utility work in the state, see the Pennsylvania overview.

Standards referenced: Pennsylvania Boiler and Unfired Pressure Vessel Law (35 P.S. 1331.1-1331.19) · 34 Pa. Code Chapter 3a · Pennsylvania Uniform Construction Code (34 Pa. Code 403.48) · ASME Boiler and Pressure Vessel Code Section VIII Division 1 and 2 · ASME Section X · ASME Section IX · ASME Section II · National Board Inspection Code (ANSI/NB-23) · ASME BPE · OSHA 29 CFR 1910.119

Frequently asked questions

Who handles pressure vessel fabrication, Pittsburgh and southwest Pennsylvania plants included?

Paul Industries designs and fabricates pressure vessels for plants in Pittsburgh, Allegheny, Beaver, Washington and Westmoreland counties, including chemical, metals, plastics and natural gas sites. Many vessels in the region serve gas processing and petrochemical units, where low-temperature impact testing, thick sections and post-weld heat treatment are common. Send the data sheet and site conditions to get a price.

Does Paul Industries build vessels for Philadelphia, Marcus Hook and the southeastern counties?

Yes. Paul Industries builds pressure vessels for pharmaceutical, biotech, chemical and energy sites in Philadelphia, Delaware County, Montgomery County, Chester County and Bucks County. Southeastern projects range from polished stainless bioprocess vessels in the suburbs to carbon steel drums and separators along the Delaware River. Each vessel is laid out for Pennsylvania clearances and the 36-month inspection cycle from the first drawing.

Who builds process vessels for the Lehigh Valley, Lancaster and Harrisburg?

Paul Industries builds reactors, receivers, cookers, heat exchanger shells and jacketed vessels for plants in Allentown, Bethlehem, Easton, Reading, Lancaster, York and Harrisburg. Food and beverage plants there often need sanitary stainless interiors with steam or glycol jackets, while chemical plants need corrosion-resistant alloys. Paul Industries sizes the design and finish to the product the vessel will hold.

How do pressure vessel manufacturers, Pennsylvania-built or out of state, get a vessel accepted here?

Any vessel installed in Pennsylvania needs ASME construction under Section VIII or X, the ASME symbol and National Board number, a keystone serial number, and an inspection before use. Where the vessel came from does not change those steps. The Department may accept another state’s registration number when a National Board inspector inspected the vessel during construction, so the data report matters as much as the nameplate.

Does every pressure vessel PA plants install need a certificate of operation?

Every vessel within the state program needs one, issued after the inspector’s report and the fees are paid. Vessels in the Department’s exempt categories, such as small air receivers within the volume and pressure limits, vessels of 6 inches inside diameter or less, and water-containing vessels of 120 gallons or less, fall outside the certificate requirement but should still be built to ASME and fitted with proper relief.

Does an ASME pressure vessel Pennsylvania plants buy need a keystone number as well as a U stamp?

Yes. A new vessel installed in Pennsylvania carries the ASME symbol, the manufacturer’s data and the National Board number, plus a Pennsylvania serial number that pairs the keystone symbol with figures no smaller than 5/16 inch. Both markings must stay visible, so nameplates on insulated vessels go on standoff brackets. Paul Industries leaves room for the keystone number on every Pennsylvania nameplate drawing.

Which inspectors can sign off a pressure vessel in Pennsylvania?

Inspections for the state program are made by people holding a current Pennsylvania Inspector Commission, which requires a National Board commission, a state examination and employment with an insurance company authorized to insure boilers in the state, an owner-user authorized to inspect its own vessels, or the Commonwealth. Commissions are renewed each calendar year. Where the plant’s insurer employs a commissioned inspector, the owner arranges the inspection through the insurer; otherwise the L&I Boiler Division inspects.

Can a pressure vessel be installed in Pennsylvania without asking the Boiler Division first?

Yes, when it meets the clearances of 18 inches at the front, rear and sides and 30 inches in front of a manhole. The vessel must still be inspected before it is used. A vessel that cannot meet those clearances needs a variance petition to the Industrial Board. Paul Industries checks clearances during layout so most vessels go in without one.

Can an existing vessel in a Pennsylvania plant be rerated?

Yes, as an alteration under the National Board Inspection Code. The rerate needs new calculations against the current thickness and material, inspector involvement before work starts, welding under the National Board R program, a pressure test and new nameplate data. Thickness surveys come first, because corrosion since construction sets what the vessel can carry. Paul Industries runs the survey, the calculations and the physical work.

What happens when a pressure vessel is moved between Pennsylvania plants?

The owner reports the new location to L&I within 10 days and keeps the vessel out of service until a Department inspector has examined it at its new site, and any fittings added during the move must comply with Chapter 3a. Paul Industries checks the vessel’s data report, thickness and relief protection against its new duty before the move, then installs, tests and prepares it for the inspector.

How long does a new ASME vessel take to fabricate for a Pennsylvania plant?

Lead time depends mostly on material availability, design complexity and finish. A carbon steel receiver from stock plate moves faster than a 316L jacketed reactor with polished interior and forged nozzles, and plate for low-temperature or alloy service can set the schedule by itself. Paul Industries gives a schedule with the quote, showing drawing approval, material receipt, fabrication, testing and delivery as separate milestones.

Do pressure vessels in a PSM-covered Pennsylvania process need extra records?

Processes covered by OSHA’s process safety management standard must keep mechanical integrity records for pressure vessels, including written inspection and test procedures and documented results. The fabrication package, with design calculations, material reports, examination and test records and the data report, is the starting point for that file. Paul Industries supplies it in an order the plant’s integrity program can use directly.

What materials suit pressure vessels for Marcellus gas service?

Wet gas and produced liquids call for carbon steel with a corrosion allowance, and low-temperature service, such as downstream of chilling or expansion, needs steels with impact testing at the minimum design metal temperature. Sour or high-chloride streams can push toward stainless or clad construction. Paul Industries sets the material from the gas analysis, the temperature range and the expected life.

Are autoclaves and quick-opening vessels covered differently in Pennsylvania?

Chapter 3a has a section dedicated to autoclaves and quick-opening vessels, alongside sections for steam and hot water heat exchangers, because their closures and interlocks create risks a bolted vessel does not have. Quick-opening closures need interlocks that prevent opening under pressure. Paul Industries designs and installs sterilizer and autoclave vessels with the closure and safety features those rules expect.

Which pressure vessel scope can Paul Industries supply for a Pennsylvania project?

Paul Industries offers supply only, where the vessel ships to the owner’s installer, design-build, where Paul Industries designs from process data and builds to suit, and complete installation, covering setting, piping, insulation, testing and turnover for the Pennsylvania inspection. Owners pick the route that fits their project, and the documentation package is the same in each.

What should a quote request for a Pennsylvania pressure vessel include?

Include the contents, design pressure and temperature, minimum design metal temperature, volume or dimensions, nozzle sizes and ratings, material and corrosion allowance, internal finish, jacket or internals, supports, and the delivery and setting conditions at the site. Add whether the vessel sits in a PSM-covered process. Paul Industries returns a price, a schedule and the drawing approval steps.

Who supplies vacuum-rated stainless vessels for King of Prussia and Malvern biotech sites?

Paul Industries supplies and installs vacuum-rated 316L stainless vessels for biotech and pharmaceutical facilities in King of Prussia, Malvern, Exton, West Chester and the wider Great Valley. Vessels are designed for full vacuum and steam sterilization, finished to the specified interior Ra, and delivered with weld maps and material records that support commissioning and validation at the site.

What design temperature should a separator for northern tier gas service use?

The design temperature should come from the coldest site conditions plus any colder process condition, such as gas expansion or liquid flashing during blowdown. That minimum design metal temperature sets whether carbon steel parts need impact testing. Paul Industries agrees the value with the owner from site and process data before materials are ordered, because changing it later means new plate.

Need a pressure vessel built or rerated for a Pennsylvania plant?

Send the data sheet or sketch, contents, design conditions, nozzle list and site setting details. Call 201-450-8280 or request a quote.