Paul Industries designs, fabricates, installs and tests process piping in Ohio for refineries, chemical and polymer plants, pharmaceutical and biologics sites, food and beverage plants, steel mills and the semiconductor fab under construction in New Albany. The work runs from carbon steel hydrocarbon lines and alloy chemical service to orbital-welded stainless for biologics and ultra high purity gas lines, all built to ASME B31.3 or the code the service requires. Paul Industries plans each job around an operating plant’s production and turnaround calendar, so new lines tie in with the least possible downtime.

Request a quote or call 201-450-8280

Headquarters 256 Shore Drive, Kilmarnock, Virginia
Building codes 2024 Ohio Building, Mechanical and Plumbing Codes (2021 I-codes)
Boiler piping ASME B31.1, 2022 edition, adopted by Ohio rule
Before digging Ohio811 notice at least two working days ahead
Public work Prevailing wage above $250,000 new, $75,000 repair
Reviewed November 2026

Which systems count as process piping in Ohio plants?

Process piping in Ohio plants is the piping that carries raw materials, intermediates, products, utilities and wastes through a production process, as distinct from the plumbing and building heating systems that serve the people in the building. ASME B31.3 defines its scope the same way: piping typically found in petroleum refineries, chemical, pharmaceutical, textile, paper, semiconductor and cryogenic plants, food and beverage processing, and related processing plants and terminals.

The answer to what is process piping work on an Ohio site therefore covers more than the main product lines. Process piping examples include crude and product lines in a Toledo refinery, solvent and monomer lines in a Lima chemical plant, cell culture media and buffer lines in a Columbus biologics suite, carbon dioxide and glycol lines in a brewery, compressed air and nitrogen headers in a steel mill, and specialty gas lines in a semiconductor fab. Plant steam and condensate, cooling water and process vacuum usually count as well, because they serve the process directly.

What is process piping used for?

Process piping is used to move fluids between the equipment that makes a product: from storage to reactors, through heat exchangers and separators, to filling lines and back through recovery systems. It also carries the utilities those steps depend on, such as steam, cooling water, instrument air, nitrogen and clean utilities, and it carries waste streams to treatment. Every line is designed for its fluid, pressure, temperature and the consequence of a leak, which is why process piping and equipment are specified together.

Process piping types found in Ohio plants
ServiceTypical materialJoining methodWhere in Ohio
Hydrocarbon and refinery serviceCarbon steel, chrome-moly, stainlessButt-welded, flangedLima, Toledo and Canton refineries
Chemical and polymer serviceStainless, alloy, lined steel, plasticsWelded, flanged, fusedLima, Northeast Ohio, Ohio River valley
Biologics and pharmaceutical316L stainless to ASME BPEOrbital welded, sanitary clampColumbus, New Albany, Cincinnati
Semiconductor gases and chemicalsElectropolished 316L, PFA, double containmentOrbital welded, face seal, fusedNew Albany
Food, brewing and consumer products304L and 316L stainlessOrbital welded, sanitary clampColumbus, Lima, Southwest Ohio
Steam, condensate and utilitiesCarbon steel, stainlessWelded, threaded on small boreEvery plant and campus

Process piping vs plumbing under the 2024 Ohio codes

Process piping vs plumbing in Ohio is a question of what the piping serves: plumbing supplies potable water and removes sanitary waste for the occupants under the 2024 Ohio Plumbing Code, building heating and cooling piping falls under the 2024 Ohio Mechanical Code, and process piping serves production and is designed to ASME B31.3 or another B31 section. All three codes, based on the 2021 International codes, took effect on March 1, 2024, and projects submitted to the building department before that date stay under the previous edition.

The boundary matters at three points. Where process water connects to the potable supply, the plumbing code’s backflow protection applies. Where a building houses process equipment, the building code governs fire separation, hazardous material quantities and the structural support of piping racks. Where the piping carries steam from a boiler, the boiler external piping falls under ASME B31.1, which the Ohio boiler rules adopt in its 2022 edition. Paul Industries draws those boundaries on the drawings before the permit application, so the building official reviews the parts that belong to the building and the plant engineer controls the rest.

Which codes do process piping contractors follow at Ohio plants?

Process piping contractors at Ohio plants build to ASME B31.3 for chemical, pharmaceutical, semiconductor, refinery and food process lines, to ASME B31.1 for boiler external piping and power plant steam, to ASME BPE for bioprocessing systems, and to owner specifications that often add requirements above the code. Welding procedures and welders are qualified under ASME Section IX in every case.

B31.3 sorts each line by fluid service. Normal fluid service covers most lines. Category D covers nonflammable, nontoxic fluids at modest pressure and temperature with lighter examination. Category M covers fluids so toxic that a single exposure could cause serious harm, with tighter design, examination and leak testing. High pressure and high purity services carry their own chapters. The chosen category sets the examination percentage, the leak test and the documentation, so it is fixed with the owner before fabrication starts.

B31.3 also assigns roles. The owner is responsible for classifying fluid services, for deciding whether a Category M or high pressure designation applies, and for appointing an owner’s inspector who verifies that examination, testing and records meet the code. The designer is responsible for the design calculations, flexibility analysis on hot lines and support design. The fabricator and erector are responsible for welding, examination and testing to the requirements. On a design-build job, Paul Industries carries the design, fabrication and erection roles and works directly with the owner’s inspector, giving one point of accountability for the code requirements from the first isometric to the final test record. Stress analysis on hot or long lines, pipe support design and nozzle load checks on pumps and vessels are included where the service calls for them.

Testing and examination by B31.3 fluid service
Fluid serviceTypical examplesExaminationLeak test
Category DCooling water, low pressure air, nontoxic utilitiesVisual examinationInitial service leak test permitted
NormalHydrocarbons, most chemicals, steam within B31.3Random radiography or ultrasonic examination of a set percentage of weldsHydrostatic at 1.5 times design, adjusted for temperature, or pneumatic at 1.1 times
Category MHighly toxic chemicals such as phosgene or hydrogen cyanideIncreased examination as the code requiresSensitive leak test added to the pressure test
High purityBioprocess and semiconductor linesVisual and borescope examination of orbital weldsPressure test plus helium leak testing where specified
High pressureHydraulic and high pressure gas linesFull examinationHydrostatic test to the high pressure chapter

Plants handling highly hazardous chemicals above OSHA’s threshold quantities run any piping change through management of change under 29 CFR 1910.119, with updated process safety information, a pre-startup safety review and training before the line enters service. Paul Industries prepares the piping documentation those reviews need: isometrics, material certifications, weld maps, examination records and test reports.

Process piping across Ohio’s industrial regions

Process piping across Ohio follows a broad industrial base, and each region brings a different mix of fluids, materials and outage patterns. The codes stay the same from Toledo to Cincinnati; the work they govern changes.

Central Ohio: New Albany and Columbus

Central Ohio is where the newest process piping is being built. Intel’s Ohio One site in New Albany is under construction, with the first fab’s construction now targeted for completion in 2030, and a fab of that kind runs miles of ultra high purity gas, chemical distribution, process vacuum and exhaust piping. Also in New Albany, Amgen is enlarging its biomanufacturing site under a $900 million plan made public in April 2025; in Columbus, Andelyn Biosciences began commercial gene therapy supply from its modular cGMP suites in 2026, and Hikma set aside $216 million in June 2026 for oral solid dose and nasal inhalation capacity. Biologics and pharmaceutical work here centers on orbital-welded stainless, which is detailed on sanitary process piping in Ohio, and on purified water loops covered by ultrapure water systems in Ohio.

Northwest Ohio: Toledo and Lima

Northwest Ohio holds three of the state’s four refineries, two in Toledo and one in Lima, along with chemical plants and consumer products manufacturing; Procter & Gamble opened a new manufacturing facility at its Lima plant in June 2026. Refinery and chemical piping here is carbon and alloy steel built for hydrocarbon, hydrogen and acid service, and most of the work is scheduled into turnarounds. Process piping, oil and gas handling and refining work in this region share the same B31.3 discipline and the same need for tight turnaround execution.

Northeast Ohio: Cleveland, Akron, Canton and Youngstown

Northeast Ohio’s polymer, specialty chemical, metals and refining plants call for alloy, lined and stainless piping, and the Canton refinery adds hydrocarbon work. Older plants in the region often replace piping in sections as corrosion surveys find thinning, with new spools built from the original isometrics corrected to field measurements.

Southwest Ohio and the Ohio River valley

Southwest Ohio combines consumer products, food, flavor and pharmaceutical plants around Cincinnati and Dayton, and Cleveland-Cliffs’ Middletown Works, which produces about 3 million tons of raw steel a year, announced a $1 billion blast furnace and process gas project in August 2026. Steel mill piping covers oxygen, nitrogen, fuel gas, cooling water and compressed air at large diameters. Chemical and power plants along the Ohio River add their own alloy and steam work.

Pipe welding in Ohio plants that keep running

Pipe welding in Ohio plants that keep running depends on isolation, hot work control and timing more than on the weld itself. Before any cut, the line is isolated, drained, purged and verified gas-free, energy sources are locked out, and the plant’s hot work permit sets the fire watch and gas monitoring. Where a line cannot be shut down, a hot tap with a fitting welded onto the live line and a tapping machine cutting through it lets a new branch be added under pressure, after the wall thickness and service have been checked for welding.

Process piping and welding are inseparable on stainless work. Bioprocess and semiconductor lines are joined by orbital welding with purged interiors, every weld is logged and inspected by borescope or visually as the specification requires, and the weld map ties each joint to its welder, procedure and inspection record. Carbon and alloy lines use manual or semi-automatic processes with preheat and postweld heat treatment where thickness or material requires. The welding side of this work is covered on industrial welding services in Ohio.

Off-site pipe fabrication: Ohio projects built as spools and modules

Off-site pipe fabrication, Ohio projects included, moves most welding into controlled conditions before the outage begins. Spools are cut, fitted, welded, examined and tested from isometric drawings, then shipped tagged for installation; larger scopes become pipe rack modules or skids with equipment, valves, instruments and wiring already in place. The field crew then makes the final tie-in welds and bolted connections inside a short window. Spool fabrication is described on the pipe fabrication page.

Materials and corrosion in Ohio process service

Materials and corrosion decide how long Ohio process piping lasts, and the selection starts from the fluid, its contaminants, temperature and the plant’s experience with similar lines. Carbon steel remains the default for hydrocarbons, steam, condensate and many dry chemicals, with a corrosion allowance added to the wall. Chrome-moly steels take over in hot hydrogen and high temperature refinery service. Austenitic stainless handles most aqueous chemicals and all sanitary work, duplex stainless resists chloride stress corrosion cracking where 316L fails, and nickel alloys cover hot acids and chlorides.

Ohio’s climate adds external corrosion to the internal picture. Insulated lines that cycle through freezing and thawing collect moisture under the jacketing, and corrosion under insulation is a recurring finding on older carbon steel racks around Lake Erie and along the Ohio River. Paul Industries specifies coatings beneath insulation on carbon steel that operates in the susceptible temperature range, seals jacketing at supports and penetrations, and places inspection ports at the low points where water gathers. Lined steel, PVDF, PFA and fiberglass lines fill the gaps where no economical metal resists the fluid, each with its own joining method and support spacing.

Compressed air, nitrogen and utility headers

Compressed air, nitrogen and other utility headers are process piping in the plants that depend on them, and their failures stop production as surely as a product line leak. Instrument air headers need dry, oil-free air delivered without pressure drop to the farthest user, so they are sized for future loads and looped where reliability matters. Nitrogen headers serve inerting, blanketing and purging, and their purity is protected by clean, leak-tight construction. Cooling water, chilled water, glycol and process vacuum headers round out the utility set.

Paul Industries builds utility headers in carbon steel, stainless, copper or aluminum systems as the service and the owner’s standard require, with isolation valves placed so sections can be shut down for tie-ins without starving the rest of the plant. Leak surveys on existing air systems often pay for header repairs quickly, because leaking compressed air wastes the electricity spent to make it.

Tie-ins, testing and winter work at Ohio plants

Tie-ins, testing and winter work are where an Ohio piping schedule is won or lost. Each tie-in is listed with its isolation points, drain and vent locations, welding or bolting method, examination and test, and grouped into the shutdown windows the plant can offer. Lines are cleaned and flushed after installation, and pressure tested to the code: under B31.3 a hydrostatic leak test at not less than 1.5 times the design pressure, adjusted for temperature, or a pneumatic test at 1.1 times where water cannot be tolerated.

Ohio winters complicate hydrostatic testing outdoors. Test water in exposed lines freezes, so tests are scheduled for warmer days, run with heated water or glycol where the service allows, or drained immediately after the hold. Outdoor process lines carrying water, viscous products or condensing gases need heat tracing and insulation sized for the coldest conditions the site sees, covered on the heat tracing page. Paul Industries plans the test medium, its source and its disposal during design, so freezing weather changes the method rather than the date.

A tie-in plan for an operating Ohio plant
StepBefore the shutdownDuring the shutdown
SurveyField-verify each tie-in point, wall thickness and isolation valvesConfirm isolation and drain points match the survey
FabricationBuild spools with field-fit allowances; examine and test off siteCut in, fit up and make the closing welds
PermitsPrepare hot work, line break and confined space permits with the plantIssue permits shift by shift; maintain fire watch
ExaminationBook radiography or ultrasonic crews for the windowExamine closing welds before insulation or burial
TestingPlan test medium, test boundaries and disposalPressure test, or apply the code’s closure weld alternative where testing is impractical
TurnoverPrepare red-line isometrics and the records listRelease the line to operations with the records signed

Digging, permits and public work rules on Ohio piping projects

Digging, permits and public work rules add state requirements beyond the piping codes. Before any excavation for buried process lines, foundations or pipe rack footings, Ohio law requires notice to the utility protection service, known as Ohio811, at least two working days ahead, not counting the day of notice, and no more than 16 calendar days ahead, under Revised Code 3781.28 as amended effective June 9, 2026. Buried lines carrying petroleum from an underground tank follow the fire marshal’s rule requiring double-wall piping on new systems, with suction lines the exception, and tank connections are covered on tank fabrication in Ohio.

Piping that serves new combustion equipment is checked against Ohio EPA’s permit rules, which permanently exempt boilers and heaters at or below 10 million Btu per hour firing natural gas, distillate oil, biodiesel or liquefied petroleum gas. Piping work on a public improvement for a public authority in Ohio pays prevailing wages when the project exceeds $250,000 for new construction or $75,000 for alteration or repair, under Revised Code Chapter 4115. Steam piping that forms part of a boiler’s external piping is repaired under the boiler rules described on boiler repair in Ohio.

What sets the price of an Ohio piping project?

The price of an Ohio piping project is set by material, line size and length, fluid service category, joining method, examination and testing, access, and the number and timing of tie-ins. Stainless and alloy material cost several times what carbon steel does, and BPE or semiconductor finishes add orbital welding, borescope inspection and documentation. Category M service, full radiography or helium leak testing each add measurable cost. Work inside an operating plant adds isolation, hot work permits, scaffolding and premium-time tie-ins during shutdowns.

Paul Industries gives a budget range from line lists, P&IDs and comparable projects, then a firm price once isometrics, specifications and the tie-in plan are fixed. Owners comparing industrial piping contractors, Ohio refiners and fab builders among them, get the clearest comparison by asking each for the same scope: fabrication, installation, examination, testing, cleaning, documentation and tie-ins, priced as one package.

Who builds process piping in Ohio?

Paul Industries builds process piping in Ohio for refiners, chemical and polymer producers, pharmaceutical and biologics plants, food, brewing and consumer products manufacturers, steel mills and semiconductor projects, from Toledo, Lima and Cleveland to Columbus, Dayton, Cincinnati and the Ohio River valley. Headquartered at 256 Shore Drive in Kilmarnock, Virginia, and formerly based in northern New Jersey and then Pennsylvania, Paul Industries works across Ohio, the Midwest and all 50 states.

As an industrial piping contractor, Paul Industries covers design and isometrics, material supply, off-site spool and module fabrication, installation, welding, examination, testing, cleaning and documentation, under supply-only, design-build or complete installation routes. Plants that want process piping specialists for one discipline, such as orbital-welded bioprocess lines or alloy refinery work, get the same team carrying the job through startup. The headquarters state’s approach is on process piping in Virginia, and a contrasting program on process piping in New York. The national service is on process piping, and the state overview on the Ohio page.

Process piping work from Paul Industries for Ohio plants

Paul Industries carries Ohio piping from the line list to a tested, documented system: code and fluid service set with the owner, spools fabricated off site, tie-ins planned into the plant’s windows, welds examined and logged, lines tested and cleaned, and turnover records ready for the plant’s mechanical integrity or qualification program. To start, send the P&IDs or line list, material specifications, the tie-in locations and the shutdown windows available, and request a quote.

Standards referenced: ASME B31.3 Process Piping · ASME B31.1 Power Piping, 2022 edition (adopted in OAC 4101:4-3-01) · ASME BPE · ASME BPVC Section IX · 2024 Ohio Building Code · 2024 Ohio Mechanical Code · 2024 Ohio Plumbing Code · Ohio Revised Code 3781.28 (underground utility notification) · Ohio Revised Code Chapter 4115 (prevailing wage) · OAC Chapter 1301:7-9 (underground storage tank piping) · OSHA 29 CFR 1910.119 · SEMI F57

Frequently asked questions

Which stainless steel process piping contractors build for biologics sites in New Albany and Columbus?

Paul Industries builds orbital-welded 316L stainless process piping for biologics, gene therapy and pharmaceutical sites in New Albany, Columbus and Licking County. The work follows ASME BPE for surface finish, slope, dead legs and weld acceptance, with a weld map, borescope records and passivation reports in the turnover package the site’s qualification team uses.

What should a plant ask industrial process piping contractors before an Ohio project?

A plant should ask industrial process piping contractors how they will classify each line under B31.3, what examination and leak tests they have priced, how tie-ins will fit the plant’s shutdown windows, what portion will be fabricated off site, and what records will be delivered. Paul Industries answers each point in its proposal and prices the scope as one package.

Does Paul Industries pipe refinery turnarounds in Toledo and Lima?

Paul Industries installs carbon steel, chrome-moly, stainless and alloy piping at refineries and chemical plants in Toledo, Lima and Northwest Ohio. Most of that work is timed to turnarounds, so Paul Industries fabricates spools ahead of the shutdown, stages them by tie-in, and completes examination, testing and documentation before the unit restarts.

Does Paul Industries take process piping work in Cleveland, Akron and Youngstown?

Paul Industries takes process piping work at polymer, chemical, metals and refining plants in Cleveland, Akron, Canton, Youngstown and the rest of Northeast Ohio. Replacement work there often follows corrosion surveys, with new spools fabricated from corrected isometrics and installed section by section to keep the plant running.

Who handles process piping for plants in Cincinnati and Dayton?

Paul Industries handles stainless, carbon steel and utility piping for consumer products, food, flavor, pharmaceutical and aerospace plants in Cincinnati, Dayton, Hamilton and the Miami Valley. Food and consumer products lines are often sanitary stainless with clean-in-place circuits, and Paul Industries schedules tie-ins between production campaigns.

What does a process piping company deliver at the end of an Ohio job?

A process piping company delivers a tested system and the records behind it: as-built isometrics, material test reports and heat numbers, weld maps with welder and procedure identification, examination and test reports, cleaning and flushing records, and for bioprocess lines borescope, slope and passivation records. Paul Industries assembles those into the turnover package the plant’s integrity or qualification program needs.

Does a process piping change at an Ohio plant need a building permit?

Process piping inside an industrial plant is usually governed by the owner’s engineering and the B31 codes, while the building, mechanical and plumbing codes govern the building, its potable water, heating and fire protection. Changes that touch structure, fire separation, hazardous material quantities or plumbing connections go to the building official. Paul Industries identifies those items during design and prepares the permit drawings.

When does Ohio require an Ohio811 call before piping work?

Ohio requires notice to Ohio811 before any excavation, including trenches for buried process lines, pipe rack footings and equipment foundations. Under Revised Code 3781.28, effective June 9, 2026, notice is given at least two working days ahead, excluding the day of notice, and no more than 16 calendar days ahead. Private plant lines that the utilities do not own are located separately from the plant’s drawings.

Is prevailing wage owed on piping work at an Ohio public university or hospital?

Ohio prevailing wage applies to public improvements by public authorities, including institutions supported in whole or part by public funds, when the project exceeds $250,000 for new construction or $75,000 for alteration or repair under Revised Code 4115.03. Privately funded plant work falls outside the chapter. Paul Industries confirms the owner’s status and prices the work at prevailing rates where they apply.

What piping does a semiconductor fab need besides ultrapure water?

A semiconductor fab needs bulk and specialty gas piping in electropolished stainless, chemical distribution in PFA and double-contained lines, process vacuum, exhaust and abatement ducting, process cooling water, and clean dry air. Gas lines are orbital welded, purged, particle and moisture tested and helium leak tested to the owner’s specification, and polymer chemical distribution components are commonly specified to SEMI F57.

Can new branches be added to live process lines at an Ohio plant?

New branches are added to live lines at Ohio plants by hot tapping when the line’s service, pressure, temperature and wall thickness allow welding on it in service. A fitting is welded to the pipe, a valve is mounted, and a tapping machine cuts through the wall under pressure. Paul Industries evaluates each hot tap with the plant’s engineers and follows the plant’s hot work and isolation procedures.

How are Ohio piping systems cleaned before startup?

Ohio piping systems are cleaned before startup by flushing, blowing or chemical cleaning matched to the service: water flushes for most process lines, steam blows for turbine steam supply, degreasing for oxygen service, and chemical cleaning and passivation for stainless bioprocess lines. Paul Industries plans temporary connections, strainers and disposal routes for the cleaning medium and records the results.

Which material suits chlorinated solvents, acids and caustic lines at an Ohio chemical plant?

Material for chlorinated solvents, acids and caustics depends on concentration, temperature and moisture: carbon steel handles many dry solvents and caustic below set temperatures, stainless and nickel alloys serve hotter or wetter services, and lined steel or thermoplastics cover acids no economical metal resists. Paul Industries confirms the owner’s material selection data before ordering.

Does Paul Industries supply fabricated spools without installing them?

Paul Industries supplies fabricated spools, pipe rack modules and skids to Ohio plants that install with their own maintenance teams, as well as delivering complete installations. Supply-only spools ship tagged to the isometrics, with weld maps, examination records and test reports, so the plant’s records stay complete whoever bolts them in.

How long does a process piping project take at an Ohio plant?

A process piping project at an Ohio plant takes from a few weeks for a small tie-in package to many months for a new unit or building, with material lead time, off-site fabrication and the plant’s shutdown windows setting the schedule. Paul Industries fabricates ahead of each window, so the field time inside the outage is mostly fit-up, final welds and testing.

Who builds steam and condensate piping for Ohio campuses and hospitals?

Paul Industries builds and replaces steam, condensate, chilled water and hot water piping for universities, hospitals and government campuses across Ohio. Boiler external piping follows ASME B31.1 under the Ohio boiler rules, and campus distribution follows B31.1 or B31.9 by size and pressure, with outages planned around heating and cooling seasons.

Which documents let Paul Industries price process piping for an Ohio plant?

Paul Industries prices Ohio process piping from P&IDs or a line list with sizes, materials, design conditions and fluid service, piping specifications, plot plans or a site walk, tie-in locations and the shutdown windows available. Isometrics, if they exist, sharpen the number. A budget range comes first, then a firm price once the isometrics and tie-in plan are fixed.

Adding or rerouting process lines at an Ohio plant?

Send the P&IDs or line list, material specifications, tie-in locations and shutdown windows. Call 201-450-8280 or request a quote.