Paul Industries provides tank fabrication in Florida, designing, fabricating, supplying and installing fuel and chemical storage tanks, generator day tanks, water tanks and stainless process tanks for terminals, utilities, hospitals, data centers and the sugar, citrus, beverage, phosphate and pharmaceutical plants across the state. Florida regulates petroleum and hazardous substance storage through the Department of Environmental Protection, under Chapter 62-762 for aboveground systems and Chapter 62-761 for underground ones, and a tank built without those rules in view can fail its first county inspection. Paul Industries builds each tank to the standard its service requires and installs it with the notices, tests and records the DEP rules expect.

Request a quote or call 201-450-8280

Headquarters 256 Shore Drive, Kilmarnock, Virginia
Aboveground rule DEP Chapter 62-762: tanks over 550 gallons of regulated substances
Underground rule DEP Chapter 62-761: tanks over 110 gallons
Notice before installing 30 to 45 days to the county inspector, then 48 to 72 hours
Registration fee $50 per tank, $25 each year after (Rule 62-762.401)
Wind design Florida Building Code 8th edition (2023), ASCE 7-22
Reviewed November 2026

Florida storage tank regulations: which DEP chapter applies to a new tank?

Florida storage tank regulations divide new tanks by location and contents: Chapter 62-762 of the Florida Administrative Code covers aboveground systems with individual capacities greater than 550 gallons that hold regulated substances such as petroleum products, and Chapter 62-761 covers underground systems greater than 110 gallons. Compression vessels and hazardous substance tanks over 110 gallons holding chemicals above the federal reportable quantities only need registration, and mineral acid tanks over 110 gallons follow a single rule, 62-762.891.

The exemption list in Rule 62-762.301 matters as much as the coverage. Heating oil storage under 30,000 gallons used on the premises, flow-through process vessels, systems entirely inside an industrial occupancy building, wastewater and stormwater systems including oil-water separators, LP gas, sodium hypochlorite, hydraulic and dielectric oil systems and anything mobile are all outside the chapter. Settling which side of the line a tank falls on is the first step of every Florida tank order, because it decides containment, overfill equipment, notices and fees.

How Florida’s DEP tank rules treat common plant tanks
TankRule that appliesWhat it means for the build
Aboveground diesel or gasoline storage over 550 gallonsChapter 62-762, full requirementsListed construction standard, secondary containment, overfill and spill equipment, registration, notices
Underground fuel storage over 110 gallonsChapter 62-761Double-walled construction, release detection, registration and start-up testing
Generator day tank over 550 gallonsChapter 62-762 (compliance date June 25, 2024)Treated as regulated aboveground storage
Generator day tank of 550 gallons or lessExempt under 62-762.301Built to UL 142 and NFPA 30; no DEP registration
Hazardous substance storage or compression vessel over 110 gallonsRule 62-762.401 onlyRegistration and fees; design to the chemical’s standard
Mineral acid storage over 110 gallonsRule 62-762.891 onlyThe mineral acid rule’s own requirements
Flow-through process vessel in a plantExempt under 62-762.301Built to the process standard: API, ASME BPE or 3-A as the duty requires
Storage entirely inside an industrial occupancy buildingExempt under 62-762.301Fire code and building code still govern

Tank fabrication in Florida, from data sheet to a working, registered tank

Tank fabrication in Florida runs through the same stages for a 1,000 gallon generator unit and a 2 million gallon terminal unit: define the service, choose the standard, design for the site, fabricate, deliver or erect, test, connect and hand over. What changes is how much of the work happens in a fabrication facility and how much on the site, and how many of Florida’s rules attach to the result.

The data sheet comes first: product, specific gravity and temperature, working and total capacity, design pressure and vacuum, connections, heating or cooling, mixing, venting and the site’s location, flood zone and wind exposure. The standard follows from the data: UL 142 or UL 2085 for shop-built fuel tanks, API 650 for large atmospheric storage, API 620 for low-pressure storage, AWWA D100 or D103 for water, and 3-A or ASME BPE practice for sanitary process tanks. Design then sets shell and bottom thickness, roof type, nozzles and manways, vents sized for normal and emergency venting, ladders and platforms, and the anchorage for wind and flood.

Shop-built units are welded, tested and coated or finished before they ship, then set on a prepared pad, anchored and tested again where the rules call for it, such as the interstitial test on a double-walled fuel tank. Field-erected structures are built on their foundations plate by plate, with the bottom, shell and roof welds examined as the standard requires and hydrostatically tested before entering service. Either way, the finished unit is connected with its piping, vents, gauges, overfill devices and monitoring, started up, and handed over with drawings, material records, test reports and, for regulated storage, everything the owner needs for the DEP registration and the county inspector’s file.

Florida aboveground storage tank regulations for a shop-built tank

Florida aboveground storage tank regulations for a shop-built tank, Rule 62-762.501, require it to be built to one of a set list of standards: UL 142, UL 2085, API 650, API Specification 12P, Steel Tank Institute F921, F001, F941 or F011, or PEI RP1400. Every regulated system needs secondary containment, either a double wall or a dike holding at least 110 percent of the largest tank in it, and a double-walled unit gets an interstitial integrity test after delivery and placement, before it holds product.

The above ground fuel storage tank regulations Florida applies also control filling: no tank may be filled beyond 95 percent, and each needs a visible gauge, an alarm at 90 percent, a flow cutoff at 95 percent or an impervious dike sized for overfill. The owner designates a primary overfill device, registers it and tests it every year. Spill containment goes on each fill connection outside a dike, fillbox covers are marked to API RP 1637 from June 25, 2024, and piping in contact with soil is secondarily contained and tested before service. Paul Industries fabricates or supplies the listed tank, builds the containment, fits the overfill and spill equipment and runs the start-up tests.

Field-erected tanks and the Florida tank farm

Field-erected tanks in Florida are built to API 650 or API 620 under Rule 62-762.502, inspected and tested at intervals set by API 653 with that record kept for the structure’s life, and protected from overfill under API Standard 2350. Dike fields hold 110 percent of the largest tank, release prevention barriers go under new tanks that use the alternative dike field system, and steel bottoms in contact with soil get cathodic protection designed by or under a corrosion professional.

Every Florida tank farm matters more than its size suggests, because Florida has no petroleum refineries and no major pipelines from the Gulf Coast refining centers. Terminals at Port Everglades supply South Florida, the Port of Tampa supplies much of the west coast and part of central Florida including Orlando, Port Canaveral supplies other parts of central Florida, and Jacksonville supplies the northeast, according to the U.S. Energy Information Administration. When ports closed ahead of Hurricane Irma in 2017, the flow of fuel into the state stopped. Storage capacity, and its condition, is the state’s buffer.

Paul Industries builds new field-erected tanks, replaces bottoms and shell courses, adds secondary bottoms and release prevention barriers, and repairs tanks found deficient at their API 653 inspection, with the work documented for the terminal’s DEP file.

Florida storage tank registration requirements, notices and placards

A new regulated tank in Florida carries a fixed sequence of paperwork: notice to the county inspector 30 to 45 days before installation and a confirmation 48 to 72 hours before work starts, registration through the DEP Storage Tank Facility Registration Form, financial responsibility in place, equipment drawn from DEP’s Equipment Approval and Registration List, and a registration placard displayed before fuel goes in. Florida DEP storage tank compliance inspections are carried out mostly by county and regional programs under contract to DEP, with DEP district offices covering the remaining counties, so that inspector is the person who sees the work.

Florida storage tank registration requirements and notices, in order
WhenStepRule
At designSelect the unit, containment, overfill and spill equipment from DEP’s approved and registered list62-762.851(2); 62-761.850(2)
At least 30 days before installation, new facilitySubmit the storage tank facility registration form62-762.401
30 to 45 days before installationNotify the county storage tank inspector62-762.411; 62-761.405
48 to 72 hours before workConfirm the installation date with the inspector62-762.411; 62-761.405
At installationInterstitial, containment and overfill operability tests62-762.501; 62-761.500
7 days before product, existing facilityRegister the new unit62-762.401
After fees are paidDisplay the registration placard in plain view62-762.401
By July 1 each yearPay the $25 annual renewal for each unit62-762.401

Florida storage tank registration costs $50 per tank or compression vessel at first, and Florida storage tank registration renewal is $25 a year for each one of 250,000 gallons or less, with annual caps of $5,000 per facility for regulated substance storage and $2,500 for compression vessels and hazardous substance tanks. Changes of owner, operator or service status are reported within 10 days. Florida storage tank financial responsibility, under Rules 62-762.421 and 62-761.420, is a separate obligation the owner demonstrates for its tanks, and Paul Industries schedules the installation so the owner’s paperwork is in place before the county inspector arrives.

The Florida storage tank placard is the proof a delivery driver looks for: motor fuel may not be put into a tank required to be registered unless a valid placard is displayed, and the owner, the operator and the supplier are each responsible for that. A new generator tank with no placard therefore sits empty until the paperwork catches up, which is why Paul Industries puts the registration date on the project schedule.

Florida underground storage tank regulations

Florida underground storage tank regulations in Chapter 62-761 apply to underground systems greater than 110 gallons and require, as Rule 62-761.500 sets out, secondary containment for the vessel and its piping, spill containment and overfill protection, release detection that can find a new release from any part of the system, and start-up testing of containment and release detection devices. The same notice and registration sequence applies, and equipment must appear on DEP’s approved list.

For underground storage tanks Florida floodplain rules add one more: anything buried in a flood hazard area is anchored against flotation, collapse and lateral movement, with buoyancy calculated as if it were empty, which on Florida’s high water tables is the condition that lifts them out of the ground. Paul Industries supplies double-walled underground tanks, designs the hold-down slabs and anchors, installs the system with its piping and monitoring, and runs the start-up tests the county inspector witnesses.

Generator fuel under Florida fuel tank regulations: day tank vs storage tank

The day tank vs storage tank question in Florida turns on size: a day tank system of 550 gallons or less is exempt from Chapter 62-762, while a larger one became subject to the chapter, with compliance due by June 25, 2024. Base and belly units under generators, and bulk storage feeding several day tanks, count as aboveground storage when they exceed 550 gallons, and they carry the full containment, overfill and registration requirements.

Those rules meet hurricane planning at hospitals, data centers, water and wastewater plants and emergency operations centers, where fuel runtime is set by the facility’s own standards and its emergency plan. Paul Industries sizes bulk and day tanks with the facility, builds or supplies UL 142 and UL 2085 tanks, installs the transfer pumps, piping, overfill devices and monitoring, and leaves the system ready for registration and the annual overfill test.

Stainless process tanks for Florida citrus, beverage, pharmaceutical and device plants

Stainless process tanks in Florida plants are usually outside the DEP tank rules, because Rule 62-762.301 exempts flow-through process tanks and systems entirely within an industrial building, so their design is driven by the product: 3-A sanitary standards for juice and dairy, ASME BPE finishes and drainability for pharmaceutical and device water and product, and the plant’s own cleaning and validation needs. Citrus and beverage plants use juice and blend vessels, aseptic and hot-fill buffers, sugar syrup storage, CIP units and water storage.

Florida produces about half of the country’s cane sugar, and sugar mills and refiners add syrup, molasses and juice tanks in carbon and stainless steel. Paul Industries fabricates stainless tanks with the jackets, agitator mounts, spray devices, manways and instrument nozzles the process needs, polishes and passivates them, and installs them with the sanitary process piping in Florida and the CIP and SIP systems in Florida that serve them. Tanks that need to hold pressure above 15 psi are built as code vessels under pressure vessel fabrication in Florida.

Choosing a tank type for a Florida service
ServiceTypical constructionStandardFlorida consideration
Diesel for generatorsDouble-wall carbon steel, shop-builtUL 142 or UL 2085DEP registration over 550 gallons; flood anchorage
Terminal fuel storageField-erected carbon steel, welded bottomAPI 650API 653 inspections; release prevention barrier; hurricane wind
Juice, syrup and beverage productStainless 304L or 316L, sanitary finish3-A practiceExempt as process tanks; acid service in citrus
Pharmaceutical and device water316L, electropolished, drainableASME BPEValidation records; humid plant rooms
Acids and fertilizer liquidsAlloy, lined carbon steel or fiberglassMaterial standard for the chemicalMineral acid rule 62-762.891 where it applies
Potable water storageWelded or bolted steel, coatedAWWA D100 or D103Five-year inspection and cleaning under 62-555.350

Water storage tanks for Florida public water systems

Water storage tanks Florida public water systems use for finished drinking water fall under Rule 62-555.350(2), which requires a check at least once a year that hatches are closed and screens in place, and an inspection for structural and coating integrity at least once every five years under the responsible charge of a Florida professional engineer. The same rule calls for cleaning every five years to remove biogrowth, calcium, iron and manganese deposits and sludge, and the utility keeps records of the cleaning and inspection.

That five-year cycle is the usual trigger for recoating, roof and hatch repairs, vent and overflow screen replacement, or a decision to replace the tank. Paul Industries repairs and replaces welded steel water tanks, and fabricates and installs new ones to AWWA D100, with hydropneumatic and process water tanks for industrial users built the same way.

Repairing and upgrading aging tanks in Florida’s climate

Aging tanks in Florida fail in predictable places: coatings and shell plates at the bottom course where rain and condensation collect, bottoms attacked from the soil side on wet sites, roof plates and rafters weakened by heat and humidity, anchor bolts and chairs corroded by salt air, and containment dikes cracked by settlement. A tank repaired in time costs a fraction of a replacement and keeps its registration history intact.

Repairs on regulated storage follow the inspection standard that applies: API 653 for field-erected construction and STI SP001 for shop-built units, with the repair records kept in the facility file. Paul Industries replaces bottoms and shell sections, installs secondary bottoms with interstitial monitoring, renews roofs and appurtenances, upgrades overfill and spill equipment to the current DEP rules, recoats interiors and exteriors for the exposure, and replaces corroded anchorage. When a tank is beyond repair, Paul Industries builds its replacement and plans the changeover so the facility keeps its storage capacity through the work.

Hurricane wind, flood and corrosion on Florida tank sites

Florida tank sites face three loads that inland sites rarely combine: hurricane wind on a shell that may be nearly empty, flood water that tries to float it, and constant warm, salty humidity that attacks coatings and anchors. Wind loads for an outdoor tank come from ASCE 7-22 through the 2023 (8th) edition of the Florida Building Code, whose High-Velocity Hurricane Zone rules apply in Miami-Dade and Broward; permit applications filed from December 31, 2026 fall under the 9th edition. An empty shell is the governing case for both wind and buoyancy, so anchorage is designed for the lowest liquid level, and plants with a storm procedure fill them with product or water before landfall where the product allows it.

How often should storage tanks be inspected on these sites? For regulated fuel storage, the answer comes from the construction standard: API 653 sets intervals for field-erected units, and STI SP001 sets periodic and formal inspections for shop-built ones, with owner checks in between. Coastal sites benefit from adding coating and anchor bolt checks to every inspection and after each storm. Paul Industries designs the anchorage, specifies coatings for the exposure, and repairs storm damage to shells, roofs, containment and piping.

What does a new tank cost at a Florida site?

The cost of a new tank at a Florida site is set by the tank’s capacity, material, construction (shop-built or field-erected), the standard it is built to, its containment and overfill equipment, foundations and anchorage, the piping and monitoring around it, and the access and schedule at the site. Regulated fuel storage adds DEP-listed equipment and start-up testing, stainless process work adds finish, jackets and agitation, and every outdoor installation carries the cost of Florida’s wind and flood design.

Shop-built tanks are limited by what can be shipped by road, so large-volume storage is field-erected and priced partly on the foundation and the weeks of site work. Paul Industries gives a budget range from the capacity, service and site, then a firm price once the design is fixed, and offers supply-only, design-build and complete installation routes.

Who builds and installs tanks for Florida plants and terminals?

Paul Industries builds and installs tanks for Florida plants and terminals, from generator day tanks at Miami-Dade hospitals to stainless juice vessels in Polk County and fuel storage at port terminals. Kilmarnock, Virginia, at 256 Shore Drive, is the company’s headquarters; northern New Jersey and then Pennsylvania were its earlier bases. Paul Industries works as an East Coast contractor across Florida, in all 50 states and at plants outside the United States. Owners comparing suppliers across the state get design, fabrication, delivery, installation, testing and the DEP paperwork sequence under one contract.

The headquarters-state page is tank fabrication in Virginia, the North Carolina page is tank fabrication in North Carolina, and the national standards detail sits on the tank fabrication page. Boiler condensate and feedwater tanks are covered alongside boiler repair in Florida, and the state’s wider picture is on the Florida page and the East Coast page.

Tank work from Paul Industries across Florida

Storage, fuel, water and process tanks are designed, fabricated, supplied, installed, repaired and replaced by Paul Industries across Florida, from Miami-Dade, Broward and Palm Beach to Tampa Bay, Lakeland, Orlando, the Space Coast, Jacksonville, Tallahassee, Pensacola and Fort Myers. Each tank is built to its standard, set and anchored for Florida wind and flood, connected with process piping in Florida, and handed over with its tests and records. Send the capacity, product and site through request a quote, or call 201-450-8280.

Standards referenced: Florida DEP Chapter 62-762, Aboveground Storage Tank Systems · Florida DEP Chapter 62-761, Underground Storage Tank Systems · Florida DEP Rule 62-555.350, drinking water system operation and maintenance · API 650 · API 620 · API 653 · API 2350 · UL 142 · UL 2085 · STI SP001 · NFPA 30 · Florida Building Code, 8th edition (2023) · ASCE 7-22 · AWWA D100 and D103

Frequently asked questions

Who builds tanks for plants around Port Everglades, Fort Lauderdale and Broward?

Paul Industries builds and installs fuel, chemical, water and process tanks for terminals, hospitals, data centers and plants around Port Everglades, Fort Lauderdale and the rest of Broward County. Broward sits in the High-Velocity Hurricane Zone, so outdoor tanks and their supports are designed for its wind provisions, and regulated fuel tanks follow Chapter 62-762. Paul Industries handles the design, installation and start-up tests.

Does Paul Industries fabricate tanks for Tampa Bay and Lakeland plants?

Paul Industries fabricates tanks for plants around Tampa Bay, Lakeland and Polk County: fertilizer liquid and acid tanks, beverage and juice tanks, fuel storage, water tanks and generator fuel systems. Each tank is built to the standard its contents require and anchored for the site. Paul Industries installs the tank with its piping and leaves the DEP registration steps lined up for the owner.

Who supplies process tanks to Orlando and Central Florida beverage and food plants?

Paul Industries supplies and installs stainless process tanks for beverage, juice, dairy and food plants around Orlando, Winter Haven, Ocala and Central Florida: blend and holding tanks, hot-fill and aseptic buffer tanks, syrup tanks and CIP tanks, with sanitary finishes, jackets and spray devices. Paul Industries connects them with sanitary piping and starts them up.

Does stainless steel rust in Florida?

Stainless steel can rust in Florida when chlorides from coastal air, pool chemicals or process water sit on the surface, or when carbon steel particles from fabrication are left embedded in it. Grade 316L resists chlorides better than 304L, and proper cleaning and passivation after welding restore the protective layer. Paul Industries specifies the grade for the exposure and passivates every stainless tank.

Do generator day tanks in Florida need DEP registration?

Generator day tank systems of 550 gallons or less are exempt from Chapter 62-762, while larger day tanks have been subject to the chapter since its June 25, 2024 compliance date and need registration, containment and overfill protection. Base tanks and bulk tanks feeding the generator over 550 gallons are regulated aboveground tanks in their own right.

When is a Florida storage tank placard required?

A Florida storage tank placard is issued after registration fees are paid and must be displayed in plain view at the facility. Motor fuel may not be deposited into a tank required to be registered unless a valid placard is displayed, and the owner, operator and fuel supplier are each responsible. New tanks are therefore registered before the first delivery is scheduled.

When does a Florida facility submit the storage tank facility registration form?

A new facility submits the storage tank facility registration form to Florida DEP at least 30 days before installation, either through the online business portal or on the form itself. A facility that already has registered tanks registers a new one at least 7 days before product goes in. Changes in owner, operator or service status are reported within 10 days.

Do process tanks inside a Florida plant fall under the DEP tank rules?

Flow-through process tanks are exempt from Chapter 62-762, and for industrial and manufacturing facilities the regulated integral piping ends at the forwarding pump or valve feeding process points of use. Systems entirely within an industrial occupancy building are also exempt. Building and fire codes still apply, and Paul Industries designs the tank to the process standard.

What overfill protection does a new Florida aboveground tank need?

A new shop-built aboveground tank in Florida may never be filled beyond 95 percent and needs at least one of a visible level gauge, an alarm at 90 percent, a flow cutoff at 95 percent or an impervious dike designed for overfill. The owner registers a primary overfill device and tests it every year; field-erected tanks follow API 2350.

How are mineral acid tanks treated under Florida's tank rules?

Owners of mineral acid storage tanks over 110 gallons, and facilities whose only regulated tanks hold mineral acids, comply only with Rule 62-762.891 rather than the full aboveground chapter. A previously unregistered mineral acid tank is registered within 10 days of its discovery. Paul Industries builds acid tanks in alloy, lined steel or fiberglass to suit the acid.

What does Florida require when a shop-built tank is moved to a new spot?

A relocated shop-built aboveground tank in Florida is reinstalled to the manufacturer’s specifications and inspected under STI SP001, and a field-erected tank that is moved is re-registered and reinstalled to API 653. The new location also needs containment, overfill equipment and registration updates. Paul Industries plans the move, the inspection and the reinstallation.

Should a Florida tank be anchored for flood as well as wind?

A tank in a Florida flood hazard area is anchored against flotation, collapse and lateral movement as well as wind, because floodplain ordinances require it and an empty tank in rising water floats. Underground tanks are checked for buoyancy as if empty. Paul Industries designs hold-downs, slabs and anchor bolts for both loads.

Why does Florida depend so heavily on fuel terminal storage?

Florida has no petroleum refineries and no major pipelines from the Gulf Coast, so gasoline, diesel and jet fuel arrive by tanker and barge into terminals at Port Everglades, Tampa, Port Canaveral and Jacksonville, according to the U.S. Energy Information Administration. When ports close ahead of a hurricane, terminal tanks are the supply. Paul Industries builds and repairs terminal tanks to API 650 and API 653.

How often are public drinking water storage tanks inspected and cleaned in Florida?

Rule 62-555.350(2) requires public water systems to check finished drinking water tanks at least annually for closed hatches and intact screens, to inspect them for structural and coating integrity at least every five years under a Florida professional engineer’s responsible charge, and to clean them every five years. Paul Industries repairs and replaces tanks after those inspections.

Do the above ground fuel storage tank regulations Florida enforces cover generator base tanks?

Generator base tanks, sometimes called belly or sub-base tanks, are aboveground storage tanks under Chapter 62-762 when they hold more than 550 gallons of diesel, so they need a listed tank standard such as UL 142 or UL 2085, secondary containment, overfill protection, registration and a placard. Smaller base tanks are outside the chapter but still follow NFPA 30 and the building code.

How should owners compare tank manufacturers in Florida?

Owners comparing tank manufacturers in Florida should look at whether one contract covers design to the right standard, fabrication, delivery, anchorage for Florida wind and flood, installation, start-up testing and the records the DEP registration and county inspector need. Paul Industries delivers that whole scope for fuel, water, chemical and stainless process tanks.

What is the difference between a storage tank and a pressure vessel in Florida?

Storage tanks in Florida are built to atmospheric or low-pressure standards such as UL 142, API 650 and API 620, which reaches 15 psig, and fall under DEP rules by contents. A container designed for more than 15 psi is a pressure vessel built to ASME Section VIII. Paul Industries builds both and sets the standard from the design pressure.

Which county inspects a new storage tank installation in Florida?

Florida DEP contracts most storage tank compliance inspections to county, regional and health department programs, and its district offices cover the rest, so the inspector for a new installation is the program serving the county where the tank will stand, listed in DEP’s storage tank compliance contact list. That inspector receives the 30 to 45 day notice and witnesses start-up tests. Paul Industries schedules the start-up tests with that inspector.

What details does Paul Industries need to quote a Florida tank?

Send the product stored, capacity, aboveground or underground location, indoor or outdoor setting, the site’s county and flood zone, any process connections, jackets or agitation, and the date the tank is needed. For replacements, include photos and the existing tank’s nameplate. From that, Paul Industries prepares a budget figure and a delivery date, and fixes the price when the drawings are agreed.

Planning a new, replacement or relocated tank in Florida?

Send the product, capacity, site location and whether the tank is aboveground, underground or inside a process area. Call 201-450-8280 or request a quote.