Paul Industries provides pressure vessel fabrication in Florida, designing, fabricating, supplying, installing and repairing ASME Section VIII vessels for phosphate and fertilizer complexes, sugar mills, citrus and beverage plants, aerospace and gas users on the Space Coast, and pharmaceutical and medical device manufacturers. Florida’s state boiler program is written for fired boilers, so the rules a vessel must meet come from the Florida Building Code, county codes in Miami-Dade, federal OSHA, the plant’s insurer and the purchase specification. Paul Industries builds each vessel to that full set and delivers it with the records every one of those reviewers asks for.

Request a quote or call 201-450-8280

Headquarters 256 Shore Drive, Kilmarnock, Virginia
State boiler program Covers boilers only; unfired vessels are outside Chapter 554
Construction rule ASME Section VIII via the Florida Building Code, Mechanical, Chapter 10
Miami-Dade County certificate each year for vessels over 60 psi and 5 cubic feet
Workplace safety Federal OSHA; Florida has no state plan
Wind design Florida Building Code 8th edition (2023), ASCE 7-22
Reviewed November 2026

Florida pressure vessel regulations: who has jurisdiction over an unfired vessel?

Florida pressure vessel regulations sit with building officials, OSHA and the owner rather than with a state inspection office, because the Boiler Safety Act in Chapter 554 of the Florida Statutes covers boilers heated by fuel, electricity or solar energy and stops there. The Division of State Fire Marshal’s Boiler Safety Program therefore issues no certificate for an air receiver, a reactor, an autoclave or a steam-heated cooker. The National Board’s synopsis for Florida records the result plainly: vessels are designed and stamped to ASME Section VIII unless excepted, and enforcement falls under the Florida Building Code, Mechanical, Chapter 10.

That chapter requires pressure vessels to be built and stamped to the ASME Boiler and Pressure Vessel Code unless the building official approves otherwise, and installed to the manufacturer’s instructions. Miami-Dade County goes further than the rest of the state, and several federal rules apply everywhere. The table sets out who reviews what.

Who reviews a pressure vessel in Florida
AuthorityWhat it coversWhat it asks of the vessel
Boiler Safety Program, Division of State Fire MarshalFired boilers in public assembly locationsNothing for an unfired vessel; a fired unit is a boiler and follows Chapter 554
County or city building officialFlorida Building Code, Mechanical, Chapter 10, through the mechanical permitASME construction unless otherwise approved, installation to the manufacturer’s instructions, structural support and anchorage
Miami-Dade County building officialCounty Code Section 8-11A certificate of inspection, renewed at least every 12 months, for vessels above 60 psi and 5 cubic feet
Federal OSHAPrivate workplaces statewide; Florida has no state planASME construction for air receivers (1910.169); mechanical integrity in covered processes (1910.119)
Florida DEPCompression vessels over 110 gallons holding hazardous substances above reportable quantitiesRegistration under Rule 62-762.401: $50 per vessel, then $25 a year
Boiler and machinery insurerVessels on the policyInspections and repair standards written into the policy, usually the NBIC

Miami-Dade’s county certificate for unfired vessels

Miami-Dade County is the one part of Florida where an unfired vessel needs a recurring certificate: Section 8-11 of the county code requires a certificate of inspection from the building official for any unfired pressure vessel operating above 60 psi with a volume of more than 5 cubic feet, valid for no more than 12 months and posted where the operator can see it. The building official may shorten the period, rescind the certificate or order tests whenever safety is in question. Cities inside the county, including Doral and Sunny Isles Beach, administer the same requirement through their building departments, and Paul Industries plans the first certificate inspection into the startup of every vessel that crosses those thresholds.

Why a Florida vessel still carries a full ASME record

Every ASME pressure vessel Florida plants put into service carries the same nameplate and Form U-1 data report it would carry anywhere, because the building official, OSHA, the insurer and the next owner all read those documents. National Board registration is not a state requirement in Florida, yet owners commonly write it into the order so the data report can be retrieved later from a national file. Paul Industries hands over the data report, drawings, calculations, material test reports, weld maps, examination and hydrostatic test records with each vessel.

ASME pressure vessel requirements and exemptions that matter on a Florida order

ASME pressure vessel requirements under Section VIII Division 1 begin with scope: vessels with an operating pressure of 15 psi or less, and those with an inside diameter of 6 inches or less, have long been outside the Division, along with listed water and hot water supply cases. Those ASME pressure vessel exemptions have been under review at ASME in recent code cycles, so a Florida purchase order should name the edition the vessel is built to, and the scope decision should be made with that edition open.

Inside the scope, the code governs materials, design for internal and external pressure, openings and reinforcement, welding qualified under Section IX, examination, the hydrostatic or pneumatic test, the pressure relief device and the nameplate. The general pressure vessel requirements a Florida building official checks are simpler: that the vessel is code-built, supported and anchored for the site’s loads, piped to its relief device safely, and installed as the manufacturer intended.

Steps from data sheet to an operating vessel on a Florida site
StepWhat happensFlorida-specific point
1. Data sheetService, design pressure and temperature, volume, connections, materials, corrosion allowanceWind exposure, flood zone and whether the site is in Miami-Dade or Broward recorded at the start
2. Design and calculationsShell, heads, nozzles, supports, lifting lugs and anchor bolts calculatedOutdoor vessels and their supports checked for Florida Building Code wind loads
3. Drawings and approvalOwner reviews general arrangement and nozzle scheduleMechanical permit drawings prepared where the county or city requires them
4. MaterialsPlate, forgings and pipe purchased with mill test reportsAlloy chosen for coastal chlorides and the process chemistry
5. Fabrication and examinationForming, fit-up, qualified welding, radiography or ultrasonic examination as the code requiresRecords kept for the insurer and the county reviewer
6. Test and nameplateHydrostatic test, final inspection, nameplate and Form U-1Optional National Board registration noted on the order
7. Delivery and settingShipped by road or through a Florida port, set on its foundation and anchoredFlood-zone sites anchored against buoyancy
8. Startup and recordsRelief device installed, system tested, turnover package deliveredMiami-Dade certificate of inspection obtained before operation where the county code applies

What is considered a pressure vessel in Florida plants?

A pressure vessel in Florida practice is a container designed to hold internal or external pressure, which is how Rule 69A-51.005 defines the term, and in a plant that means air and nitrogen receivers, reactors, autoclaves, jacketed kettles, deaerators, flash tanks, filter housings, heat exchanger shells, vacuum vessels and cryogenic and compressed gas storage. A pressure vessel Tampa phosphate and fertilizer plants run looks very different from one in a Miami pharmaceutical suite, but the same code governs both.

Vacuum service matters more in Florida than many buyers expect. Sugar mills boil syrup in vacuum pans, citrus plants concentrate juice in evaporators that run below atmospheric pressure, and both are designed for external pressure. A vessel that collapses under vacuum fails by buckling, so its shell thickness and stiffening rings are set by the external-pressure rules of Section VIII rather than by the internal design pressure alone.

Vessels for phosphate, fertilizer and chemical plants around Polk County and Tampa Bay

Phosphate and fertilizer production around Polk, Hillsborough, Hardee and Manatee counties is a major vessel market: the Bone Valley district supplies more than 60 percent of United States phosphate production, and the plants that turn its rock into fertilizer make sulfuric acid, concentrate phosphoric acid and handle anhydrous ammonia. Those services need alloys and linings chosen for the acid, concentration and temperature, and careful attention to weld chemistry and post-weld heat treatment where the code calls for it.

Anhydrous ammonia storage above 10,000 pounds brings the process under OSHA’s process safety management standard, 29 CFR 1910.119, whose mechanical integrity element requires written procedures, inspection and testing for pressure vessels and storage tanks, and correction of deficiencies before further use. Paul Industries designs and fabricates replacement ammonia receivers, acid service vessels and heat exchanger shells for those plants, installs them during turnarounds, and supplies the documentation the mechanical integrity program needs.

Sugar, citrus and beverage vessels across the state

Florida produces about half of the country’s cane sugar, from mills around Lake Okeechobee, and its citrus and beverage industry runs juice, bottling and canning plants across the center of the state. Their vessels include vacuum pans and evaporator bodies, juice deaerators, pasteurizer and hot-fill tanks, carbon dioxide receivers, carbonators, clean-in-place tanks and air receivers. Sanitary designs follow 3-A and ASME BPE practice for surface finish and drainability, and the process tanks around them are covered on tank fabrication in Florida.

Seasonal plants have a natural window for vessel replacement: the months between harvests. Paul Industries fabricates the replacement while the plant is still running, then removes the old vessel, sets the new one and ties it in during the off-season, with sanitary process piping in Florida and CIP and SIP systems in Florida completed under the same schedule.

Aerospace, gas storage and the Space Coast

The Space Coast around Cape Canaveral, Titusville and Melbourne runs a concentration of high-pressure gas and cryogenic storage: nitrogen, helium, oxygen and hydrogen for launch processing, test stands and manufacturing. As a market fact, the liquid hydrogen sphere NASA completed at Launch Complex 39B around 2022 holds about 1.25 million usable gallons. Aerospace and electronics plants also run nitrogen buffer vessels, vacuum chambers and air receivers built to the same Section VIII rules as any other vessel.

Transportable cylinders and tube trailers built to Department of Transportation specifications follow federal transport rules rather than Section VIII, so the line between a stationary vessel and a transport container is drawn at the start of each Space Coast order. Paul Industries designs and builds the stationary vessels, receivers and manifolds, and installs them with the process piping in Florida that connects them.

How pressure vessel fabrication in Florida fits a plant’s shutdown calendar

Pressure vessel fabrication in Florida is usually planned backward from a shutdown: a phosphate turnaround, the gap between sugar or citrus seasons, a hospital’s low-load winter months or a pharmaceutical plant’s annual maintenance week. The vessel is designed and built while the plant runs, so the shutdown is spent removing the old unit, setting the new one and connecting it, not waiting for steel.

Lead time is set mostly by materials and design approval. Heads, forgings, alloy plate and large flanges can take longer to arrive than the welding takes to complete, and an owner’s drawing review that runs for weeks moves the whole schedule. Paul Industries orders long-lead materials as soon as the design conditions are fixed, holds the drawing review to an agreed turnaround, and books the crane, the road permit and the receiving crew for the delivery date.

Large vessels for coastal plants can arrive by water through Port Tampa Bay, Port Canaveral, JAXPORT or Port Everglades, where road limits make a single-piece delivery by truck impractical. Where a vessel is too large to ship whole, it is built in sections and completed on the site with field welds examined and tested to the same code. Each route is decided at the design stage, because nozzle orientation, lifting lugs and shipping saddles all depend on how the vessel is shipped and lifted into place.

Testing is decided the same way. A shop hydrostatic test before shipping is the normal case; a field test after final assembly is planned when the vessel is completed on the site, with test water, a disposal route and temperature limits arranged in advance. The result is a vessel that arrives tested, documented and ready to connect, with the tie-in work sequenced so the plant restarts on its planned date.

Air receivers, relief devices and OSHA 1910.169 at Florida plants

Air receivers sit in almost every Florida plant, and OSHA 29 CFR 1910.169 governs them in every private workplace in the state because Florida has no state plan. The standard requires receivers to be built to ASME Section VIII, fitted with a drain pipe and valve at the bottom so oil and water can be blown off, an indicating pressure gauge, and spring-loaded safety valves sized so the receiver cannot be over-pressurized. In Florida’s humidity, compressed air carries a heavy load of water, and a receiver that is never drained corrodes from the bottom up.

Every Section VIII vessel needs overpressure protection, whether a relief valve, a rupture disk or a combination, set at or below the maximum allowable working pressure and discharging to a safe location. Paul Industries sizes the relief device for the worst credible case, including fire exposure on outdoor vessels and blocked outlets on process vessels, routes the discharge, and replaces corroded receivers with new code vessels fitted with automatic drains suited to the humid air.

Designing for Florida heat, salt air, wind and flood

Florida design conditions change four parts of a vessel order: material, coating, supports and anchorage. Coastal air carries chlorides that pit and crack austenitic stainless steel under stress and heat, insulated carbon steel suffers corrosion under insulation in constant humidity, and the Florida Building Code, 8th edition (2023), sets wind loads from ASCE 7-22 for every outdoor vessel and its supports, with the High-Velocity Hurricane Zone provisions in Miami-Dade and Broward.

The 9th edition of the Florida Building Code takes effect on December 31, 2026, and the edition that governs a project is generally the one in force when its permit application is filed, so a vessel order placed this year may be designed under one edition and permitted under the next. In flood hazard areas, Florida floodplain ordinances require tanks and vessels to be anchored against flotation, collapse and lateral movement, with an underground tank’s buoyancy calculated empty. Paul Industries designs saddles, legs, skirts and anchor bolts to those loads and states the design basis on the drawings.

Florida industries and the vessels they order
Industry and regionTypical vesselsMaterial and design notes
Phosphate and fertilizer, Polk County and Tampa BayAmmonia receivers, acid service vessels, exchanger shells, flash tanksAlloy or lining for acid service; PSM documentation for ammonia
Sugar mills, Palm Beach and Hendry countiesVacuum pans, evaporator bodies, juice heaters, air receiversExternal-pressure design; erosion and scale allowances
Citrus and beverage, Central FloridaDeaerators, hot-fill and pasteurizer tanks, CO2 receivers, carbonatorsStainless with sanitary finishes; drainable nozzles
Aerospace, Space CoastNitrogen and helium storage, vacuum chambers, manifoldsHigh design pressures; cleanliness for oxygen service
Pharmaceutical and medical device, Miami-Dade, Broward and Tampa BayJacketed reactors, autoclaves, clean steam separators, WFI vesselsASME BPE finishes; validation documentation
Hospitals, data centers and campuses statewideExpansion tanks, air separators, air receivers, water heater storageSeismic and wind anchorage; Miami-Dade certificate where above the county thresholds

Jacketed, clad and lined vessels for corrosive Florida services

Jacketed, clad and lined vessels solve the two problems Florida process plants face most often: heating or cooling a product through the wall, and holding a chemical that would attack plain carbon steel. A conventional jacket, a half-pipe coil or a dimple jacket each brings its own pressure rating, flow pattern and cleaning limits, and the jacket is a pressure chamber in its own right, designed and tested under Section VIII alongside the inner vessel.

For acid and chloride services, solid alloy is one route and carbon steel with a metallurgically joined alloy cladding or a rubber, glass or polymer lining is another; the choice turns on temperature, concentration, abrasion, the cost of the alloy and how the vessel will be inspected in service. Clad vessels need weld procedures that keep the corrosion-resistant layer intact at every seam and nozzle, and lined vessels need nozzle and manway designs the lining can follow without stress points. Paul Industries designs the jacket or lining with the process data, fabricates the vessel and tests the jacket and the shell separately before it ships.

Repairs, alterations and rerates on vessels in Florida service

Repairs and alterations to vessels in Florida service follow the National Board Inspection Code, Part 3, because no state rule substitutes another method and the insurer, the county reviewer in Miami-Dade and the plant’s own mechanical integrity program all recognize it. Welded repairs are made under the National Board R program with the inspector consulted, and the R-1 or R-2 report goes into the vessel’s file and to the insurer.

Rerating a vessel to a higher pressure or temperature is an alteration, needing calculations against the original data report, an inspection of current thickness and a test. Paul Industries assesses the vessel, prepares the repair or rerate plan for the inspector, makes the repair or fabricates a replacement when repair is uneconomic, and returns the vessel to service with its records updated.

What drives the price of a vessel built for a Florida plant?

The price of a vessel built for a Florida plant is driven by its size, design pressure and temperature, material, wall thickness, number and size of nozzles, jackets and internals, the examination and heat treatment the code requires, sanitary finish, and the delivery, rigging and setting at the site. Florida conditions add wind and flood design for outdoor supports, coatings or alloys for coastal air, and, in Miami-Dade, the county certificate before startup.

A small carbon steel air receiver and a large alloy reactor differ by orders of magnitude in cost, so Paul Industries gives a budget range from the data sheet and comparable scopes, then a firm price once design conditions, materials and connections are fixed. Supply-only, design-build and complete installation are all offered, and the quote states which route it covers.

Who fabricates pressure vessels for Florida plants?

Paul Industries fabricates pressure vessels for Florida plants, and designs, supplies, installs, tests and repairs them. The company’s headquarters is 256 Shore Drive, Kilmarnock, Virginia; it was formerly based in northern New Jersey, then Pennsylvania. As an East Coast contractor, Paul Industries builds vessels for sites throughout Florida and every other state, and for plants abroad through its international work. Owners comparing pressure vessel manufacturers Florida-wide should weigh design, fabrication, delivery, installation and documentation under one contract, which is how Paul Industries delivers every order.

The headquarters-state version of this page is pressure vessel fabrication in Virginia, and the North Carolina version is pressure vessel fabrication in North Carolina. The national code detail is on the pressure vessel fabrication page, the boiler side of Florida law on boiler repair in Florida, and the state’s wider picture on the Florida page and the Gulf Coast page.

Pressure vessels from Paul Industries for Florida owners

Paul Industries designs, fabricates, supplies, installs and repairs ASME Section VIII vessels for Florida plants from Miami-Dade and Palm Beach to Tampa Bay, Polk County, Orlando, the Space Coast, Jacksonville and the Panhandle. Each vessel is built for its service and site, delivered with a complete record, set and anchored for Florida wind and flood loads, and tied in with the piping and welding around it, including stainless work finished under passivation services in Florida. Send the data sheet or a sketch through request a quote, or call 201-450-8280.

Standards referenced: ASME Boiler and Pressure Vessel Code, Section VIII, Division 1 · National Board Inspection Code (NBIC), Part 3 · Florida Building Code, Mechanical, Chapter 10 · Florida Building Code, 8th edition (2023) · ASCE 7-22 · Miami-Dade County Code Section 8-11 · Florida DEP Rule 62-762.401, storage tank registration · OSHA 29 CFR 1910.169, air receivers · OSHA 29 CFR 1910.119, process safety management · OSHA 29 CFR 1904.39 · API 510 · API 650 and API 620

Frequently asked questions

Who builds pressure vessels for plants around Lakeland and Polk County?

Paul Industries builds pressure vessels for phosphate, fertilizer, chemical and food plants around Lakeland, Bartow, Mulberry and the rest of Polk County, and for plants along Tampa Bay. Typical orders are ammonia receivers, acid service vessels, exchanger shells and air receivers, designed for the process chemistry and fabricated with the records a process safety program needs. Paul Industries also sets and connects them during turnarounds.

Does Paul Industries fabricate vessels for Jacksonville and Northeast Florida plants?

Paul Industries fabricates vessels for chemical, paper, food and beverage, pharmaceutical and port-related plants around Jacksonville and Northeast Florida, and for hospitals and campuses there. Each vessel is designed to ASME Section VIII, built for coastal exposure and wind loads at its site, and delivered with its data report and test records. Paul Industries installs it and connects the piping.

Who supplies pressure vessels to Miami-Dade and Broward facilities?

Paul Industries supplies and installs pressure vessels for pharmaceutical, medical device, food, hospital and building plants in Miami-Dade and Broward. Both counties sit in the High-Velocity Hurricane Zone, which governs outdoor supports and anchorage, and Miami-Dade requires a county certificate of inspection, renewed at least yearly, for vessels above 60 psi and 5 cubic feet. Paul Industries designs for both.

What is considered a pressure vessel in Florida?

Florida’s rules define a pressure vessel as a container for internal or external pressure from an outside source, from heat or both. ASME Section VIII governs construction, with scope limits at 15 psi and small diameters, and the Florida Building Code requires ASME construction unless otherwise approved. Miami-Dade counts vessels above 60 psi and 5 cubic feet for its certificate.

How often do pressure vessels need to be inspected in Florida?

Florida law sets no statewide interval. Miami-Dade requires a certificate of inspection at least every 12 months above its thresholds, and elsewhere the interval comes from the insurer, OSHA’s mechanical integrity rule for covered processes and the owner’s program, often built on API 510. Paul Industries prepares vessels for inspection and repairs what the inspector finds.

Does Florida's Boiler Safety Program inspect pressure vessels?

Florida’s Boiler Safety Program inspects boilers in public assembly locations, and its statute, Chapter 554, defines a boiler as a vessel heated by fuel, electricity or solar energy. Unfired vessels such as air receivers, reactors and autoclaves are outside it. Their construction is governed by ASME Section VIII through the Florida Building Code, and their in-service care by the insurer, OSHA and county codes.

Is ASME mandatory for a pressure vessel in Florida?

Chapter 10 of the Florida Building Code, Mechanical requires pressure vessels to be built and stamped to the ASME Boiler and Pressure Vessel Code unless the building official approves otherwise, and OSHA 29 CFR 1910.169 requires air receivers to be built to Section VIII. Insurers and Miami-Dade expect the same. Paul Industries builds every vessel within the code’s scope to Section VIII.

When does a tank become a pressure vessel?

A tank becomes a pressure vessel when its design pressure rises above the limits of the tank standards: API 650 covers atmospheric tanks, with an annex allowing up to 2.5 psig, and API 620 covers large low-pressure tanks up to 15 psig. Above 15 psi, ASME Section VIII applies. Paul Industries sets the design pressure with the process data and builds to the right standard.

Do compression vessels need Florida DEP registration?

Compression vessels larger than 110 gallons that hold hazardous substances above the federal reportable quantities in 40 CFR 302.4 must be registered with Florida DEP under Rule 62-762.401, at $50 per vessel initially and $25 a year after that, with a facility cap of $2,500 a year. LP gas tanks are exempt. Paul Industries flags registration needs on the data sheet.

Are non-ASME pressure vessels allowed in Florida?

Non-ASME pressure vessels can be used in Florida only where they fall outside Section VIII’s scope or the building official approves them under the Florida Building Code, and air receivers must be ASME-built under OSHA 1910.169. Insurers rarely accept them. Paul Industries replaces non-code vessels with Section VIII vessels sized for the same duty.

How much does a pressure vessel cost for a Florida plant?

How much a pressure vessel costs depends on size, design pressure and temperature, material, nozzles, jackets, internals, examination, finish and installation, so a small carbon steel receiver and a large alloy reactor sit at opposite ends of a very wide range. Paul Industries gives a budget range from the data sheet, then a firm price once the design conditions are fixed.

How should an outdoor vessel be anchored for a Florida hurricane?

An outdoor vessel in Florida is anchored for the wind loads the Florida Building Code sets from ASCE 7-22 for its site, with stricter High-Velocity Hurricane Zone provisions in Miami-Dade and Broward, and in a flood zone also against buoyancy and lateral movement. Paul Industries designs the supports and anchor bolts and states the loads on the drawings.

What happens after a pressure vessel incident at a Florida plant?

After a pressure vessel incident, the employer reports any fatality to OSHA within 8 hours and any inpatient hospitalization, amputation or eye loss within 24 hours, and notifies the insurer. The vessel stays out of service until its damage is assessed. Paul Industries inspects it and repairs it under the NBIC or replaces it, with the cause documented.

Can a vessel built for another state be moved to a Florida plant?

A vessel from another state can be moved to a Florida plant when its nameplate and data report are intact and an inspection shows its condition supports the intended pressure. Florida has no state vessel number to transfer, but Miami-Dade issues its own certificate. Paul Industries inspects, repairs or rerates the vessel, then installs it.

Does salt air affect stainless pressure vessels on the Florida coast?

Salt air deposits chlorides on stainless steel, and on warm vessel surfaces under stress those chlorides cause pitting and stress corrosion cracking, especially under insulation. Paul Industries specifies alloys, coatings, insulation jacketing and sealed seams for the exposure, and passivates welded stainless surfaces so the vessel holds up in coastal service.

How often do pressure vessels need to be tested after a repair in Florida?

The NBIC and the inspector set the answer rather than a Florida statute: a welded repair or alteration is normally followed by a pressure test or approved alternative examination, and routine inservice programs use thickness readings and inspections instead of repeated hydrostatic tests. Paul Industries runs the test the inspector specifies.

What details let Paul Industries price a Florida vessel?

Send the service, design pressure and temperature, volume or dimensions, material, connections and nozzle sizes, jacket or internals, the site’s location and whether the vessel stands outdoors, and the date it is needed. A sketch or an existing nameplate is enough to start. Paul Industries returns a budget range and schedule, then a firm price once the design is fixed.

Need a code vessel built or replaced at a Florida plant?

Send the data sheet, a sketch or the nameplate of the vessel being replaced, with the site location and the date you need it. Call 201-450-8280 or request a quote.