Paul Industries provides boiler repair in West Virginia for chemical plants, hospitals, universities, manufacturers and public buildings, repairing firetube and watertube steam boilers, burners, controls and safety devices to the state’s steam boiler law and the National Board Inspection Code. West Virginia regulates every steam boiler carrying more than 15 psi through an annual permit to operate issued by the Division of Labor, so a repair is planned around the inspection that comes before it and the permit that follows it. Paul Industries diagnoses the fault, repairs or replaces the failed parts, runs the tests and hands over the records the inspector and the insurer expect.

Request a quote or call 201-450-8280

Headquarters 256 Shore Drive, Kilmarnock, Virginia
State law W. Va. Code 21-3-7: steam boilers above 15 psi
Legislative rule 42 CSR 3, effective June 9, 2021
Permit to operate Valid 12 months, posted under glass in the boiler room
New or temporary boiler Permit to install applied for at least 15 days ahead
Reviewed November 2026

What does the West Virginia boiler code require of a steam boiler?

The West Virginia boiler code is two documents: W. Va. Code 21-3-7, which requires a permit to operate for any steam boiler carrying more than 15 pounds per square inch, and the Division of Labor’s legislative rule 42 CSR 3, which sets out how boilers are installed, inspected, permitted and repaired. The rule took effect on June 9, 2021 and runs until June 9, 2031 unless the Legislature renews it. It covers high-pressure steam boilers and forced flow steam generators, the once-through units that turn water to steam in a single pass through a coil.

Rather than writing its own technical requirements, the rule adopts national ones by reference. New power boilers are built to ASME Boiler and Pressure Vessel Code Section I. Installation, inspection, repairs, alterations and pressure relief devices follow Parts 1 to 4 of the National Board Inspection Code (NBIC). Administrative matters, from inspection frequency to condemned and secondhand boilers, follow selected sections of the National Board’s recommended rules, NB-132, with the inspection interval set at one year. For a plant engineer, the practical meaning is that a repair accepted under the NBIC in another state is built to the same technical standard in West Virginia, while the permit, the serial number and the paperwork are West Virginia’s own.

The statute lists boilers that fall outside the permit system: railroad locomotive boilers under federal inspection, portable agricultural and automobile boilers, private residence boilers, sectional boilers, small portable boilers used at oil and gas wells, and boilers under federal jurisdiction. Low-pressure steam and hot water heating boilers sit outside the 15 psi threshold, and their repairs follow ASME Section IV, the NBIC and the insurer’s requirements. Paul Industries repairs boilers on both sides of that line and keeps the same records on each.

The West Virginia steam boiler permit cycle under 42 CSR 3
StepWhat the rule requiresWhat it means for a repair
Permit to installApplication to the Division at least 15 days before a new boiler is installed, including temporary unitsReplacement and rental boilers need the application filed before they are set, so it goes on the outage schedule first
Final inspection and WV numberThe Division assigns a West Virginia serial number, marked on the boiler where the ASME Code specifiesInsulation, lagging and casing repairs leave the number visible; covering it breaks the rule
Annual inspectionInternal and external inspection while the boiler is out of pressure, by a state inspector or an insurer’s special inspectorThe inspection outage is the natural repair window; findings become the repair list
Report to the DivisionInspection report on the National Board form, submitted within 10 daysRepairs ordered by the inspector are documented against that report
Permit to operateIssued after the report and the fee; states the maximum allowable pressure; valid 12 monthsA repair that changes pressure or capacity is an alteration and needs the permit updated
PostingPermit posted under glass in the engine or boiler roomThe posted permit is the first thing to check before any work starts

How boiler repair in West Virginia fits the Division of Labor permit cycle

Boiler repair in West Virginia usually starts at the annual inspection, because 42 CSR 3 requires every permitted steam boiler to be opened and examined inside and out each year, and the inspector’s findings decide what must be repaired before a new permit is issued. The owner prepares the unit: it is cooled, drained, opened at the manways and handholes, and cleaned enough to be examined. The rule lets an inspector decline to inspect a unit left unprepared, and the Division then holds the permit until it is ready and inspected.

Paul Industries plans that outage as a repair window rather than a paperwork visit. Before the outage, the plant’s last inspection report, water treatment logs, burner service records and any alarm history are reviewed, so that likely findings are anticipated and materials such as gaskets, tubes, refractory and relief valves are ordered in advance. When the inspector’s findings arrive, the repair proceeds without waiting on parts, and the unit is closed, tested and returned to the permit cycle.

The annual boiler inspection West Virginia law requires covers design, construction, installation, condition, appurtenances and operation. In practice an inspector looks at the waterside for scale, corrosion and pitting; the fireside for tube thinning, cracking, bulging and refractory damage; and the controls for working low-water cutoffs, pressure controls, flame safeguard and relief valves of the right capacity and set pressure. Each of those becomes a repair item if it falls short.

From inspection finding to finished repair on a West Virginia boiler

An inspection finding on a West Virginia boiler becomes a repair through three steps: classifying the work under the NBIC, carrying it out with the inspector involved where the code calls for it, and documenting it so the next permit can be issued. Classification matters most, because the NBIC treats a routine repair, a welded repair to a pressure part and an alteration very differently.

Routine maintenance items, such as replacing gaskets, cleaning tubes, repairing refractory that carries no pressure, and servicing burners and controls, restore the unit without touching pressure-retaining welds. A welded repair to a pressure part, such as replacing a cracked tube, welding a pitted area in a drum or rebuilding a tube sheet ligament, is made under the National Board R program, with an inspector consulted before the work and accepting it afterwards, and is recorded on an NBIC repair report. An alteration, which changes the design, such as its allowable pressure or heating surface, needs design calculations and the inspector’s acceptance before it starts.

How common boiler repairs are classified and documented in West Virginia
RepairNBIC treatmentInspector involvementRecords handed over
Retubing a firetube boilerRepair; tube ends expanded or welded to the code and original designConsulted before work; hydrostatic test witnessedNBIC repair report, test record, tube material records
Watertube tube replacementWelded repair under the R programConsulted before work; welds and test acceptedRepair report, welding procedure and welder records, examination results
Drum or shell weld repairWelded repair; method agreed in advanceRequired before and afterRepair report, examination results, test record
Rerate or added heating surfaceAlterationRequired; design reviewed before workAlteration report, calculations; the permit to operate updated
Relief valve repair or replacementRepair under NBIC Part 4; repaired valves carry the VR program nameplateConfirms set pressure and capacity at inspectionValve data, set pressure and capacity record
Refractory, burner and controlsMaintenance; no pressure-part weldingReviewed at the next inspectionService report, combustion analysis, safety device test sheet

Boiler repair welding is where most of the documentation sits. Pressure-part welds are made to qualified welding procedures with qualified welders, using material that matches or is accepted in place of the original, and are examined as the NBIC and the original construction code require before the hydrostatic test. The National Board’s 2024 synopsis lists West Virginia’s stamping requirements as the National Board NB, R and VR marks and the ASME power boiler marks S, A, E, M, PP and V, which is why the R program and the VR program appear on almost every repair file for a high-pressure steam boiler West Virginia permits. Paul Industries assembles that file as the work proceeds and hands it to the owner at the end.

Insurance company inspections and special inspectors in West Virginia

Most industrial steam boilers in West Virginia are inspected by an insurance company’s special inspector rather than a state inspector, because W. Va. Code 21-3-7 exempts a boiler carrying insurance from Division inspection in any 12-month period when the insurer’s own inspector has examined it. The special inspector holds a National Board commission and a West Virginia certificate of competency, renewed every year, and sends the inspection report to the Division, which invoices the owner and issues the permit.

Insurers also report to the Division. When an insurer changes or cancels coverage it notifies the Division, and when it refuses coverage after an inspection it sends the Division a list of the defects found. For an owner, that means a repair recommendation from the insurer’s inspector carries regulatory weight: a boiler without coverage falls back to state inspection, and the defect list stays on its record. Paul Industries works from the special inspector’s report, agrees the repair method with the inspector before welding starts, and schedules the acceptance inspection and hydrostatic test so that the insurer and the Division both receive what they need.

How often is a boiler inspected in this system? Once a year, whichever inspector does it, because the rule replaces the National Board’s model three-year interval with one year. Forced flow steam generators are the exception: their permit runs for the inspection schedule the inspector sets, up to 24 months.

What happens when a West Virginia boiler is condemned?

A West Virginia boiler is condemned when an inspector or special inspector finds it unsafe to operate, and the inspector then stamps the condemnation mark, written as WXXXW, over the boiler’s West Virginia serial number. The owner has five days from notice to file a written appeal with the Commissioner, and the boiler stays out of service while the appeal is heard. A boiler condemned in any other state is barred from operating in West Virginia.

Condemnation is rare, but suspension is a related and more common risk: the Commissioner or an inspector suspends or revokes a permit to operate when the boiler is out of compliance with the Act or the rule, and the suspension continues until an inspector confirms the boiler is back in compliance and the Commissioner reinstates the permit. Operating a steam boiler without a permit is a misdemeanor carrying a fine of $100 to $500, with each day counted as a separate offense. When a boiler is condemned or its permit is suspended, Paul Industries assesses whether a repair can bring it back to the code, sets out the repair and test plan the inspector needs to see, and prices replacement alongside it so the owner decides with both numbers in hand.

Replacing, moving or adding a steam boiler in West Virginia

Replacing, moving or adding a steam boiler in West Virginia starts with paperwork at two agencies: the Division of Labor for the permit to install, and the Department of Environmental Protection’s Division of Air Quality for any air permit the new unit needs. The permit to install is applied for at least 15 days before the boiler is set, and the same lead time applies to a boiler brought in for temporary use. When a boiler already in service is moved from one location to another, the owner notifies the Division with the West Virginia serial number and both locations.

Air permitting depends on size, fuel and the plant’s existing permit. West Virginia’s construction and modification permit rule, 45 CSR 13, applies to new and modified stationary sources, with a table of de minimis units, and 45 CSR 2 limits particulate matter from fuel burning in indirect heat exchangers. At the federal level, 40 CFR 60 Subpart Dc applies to steam generating units with a maximum design heat input of 10 to 100 million Btu per hour built or modified after June 9, 1989, and boilers at major sources of hazardous air pollutants fall under 40 CFR 63 Subpart DDDDD. Gas-fired boilers are excluded from the area source boiler rule, 40 CFR 63 Subpart JJJJJJ, which is one reason fuel choice shapes the paperwork for an industrial boiler West Virginia plants install. Paul Industries sizes, supplies and installs replacement boilers and assembles the equipment data the plant’s environmental staff need for the air permit file.

Coal boiler repair and conversions in West Virginia

Coal boiler repair still matters in West Virginia, where coal-fired plants supplied 86 percent of the state’s electricity generation in 2023 according to the U.S. Energy Information Administration, and where some institutional and industrial boilers were built to burn solid fuel. Coal-fired and stoker-fired units wear in ways that gas-fired units rarely do: grate and stoker components erode, ash and slag build up on tubes and refractory, and soot blowing and ash handling equipment need regular repair.

Repairs on these units focus on erosion and corrosion at tube surfaces that see ash-laden gas, refractory around the stoker and furnace openings, and the fuel feed and ash removal systems. Where an owner converts a solid-fuel unit to natural gas, the burner, controls and flame safeguard change, and the conversion is reviewed for the permit to operate and the plant’s air permit. Paul Industries repairs coal and stoker units, carries out fuel conversions, and replaces equipment that is past economic repair.

Boiler repair priorities by West Virginia region
RegionTypical boiler ownersRepair emphasis
Charleston and the Kanawha ValleyChemical and specialty chemical plants, hospitals, state government buildingsProcess steam reliability, watertube repairs, coordination with plant turnarounds
Huntington and the Tri-StateManufacturers, hospitals, university buildingsFiretube retubing, burner and controls upgrades, summer outage work
Parkersburg and the Mid-Ohio ValleyChemical and polymer manufacturers, industrial parks along the Ohio RiverProcess steam boilers, deaerators and feedwater systems
Boiler repair, Morgantown, WV and the I-79 corridor to Fairmont and ClarksburgUniversity and hospital central plants, energy sector facilitiesCentral plant boiler overhauls, steam distribution, condensate return
Wheeling, Weirton and the Northern PanhandleSteel and metals plants, manufacturers, hospitalsHeavy-duty industrial boilers, waste heat and process steam
Martinsburg and the Eastern PanhandleManufacturing, distribution and federal facilitiesHeating plants, replacement boilers and permit-to-install planning
Beckley, Bluefield and the southern countiesHospitals, schools, institutional heating plantsOlder boilers, solid-fuel history, conversions and replacements

Keeping steam available while a West Virginia boiler is down

Keeping steam available while a West Virginia boiler is down takes either a second permitted boiler with spare capacity or a temporary boiler, and the temporary route has a state step that catches owners out: a boiler brought in for temporary use needs its own permit to install, applied for at least 15 days in advance. A rental unit that arrives the day the outage begins has no legal footing to make steam.

For a planned repair, Paul Industries confirms the steam load during the outage, checks the spare capacity of the remaining units, and where it falls short, arranges the temporary unit, its permit application, its connections to the steam header, feedwater and fuel, and its removal afterwards. For a repair that will run past the permit’s expiry date, the rule allows the Commissioner to grant an extension of up to 60 days for good cause, and a second extension to a maximum of 120 days in a year, supported by statements from the inspector and the insurer. Planning the repair inside the permit year avoids relying on either.

Steam distribution often decides how long an outage lasts. Valves that leak through when closed, failed steam traps and leaking condensate returns all slow the shutdown and the restart, so the outage plan includes them. The water side matters too: a repaired unit returned to poor water will scale and corrode again, which is why the repair scope often includes the boiler water treatment program and the deaerator.

What does boiler repair cost in West Virginia?

Boiler repair cost in West Virginia depends on the boiler type and size, the extent of the damage, how much pressure-part welding is involved, whether a hydrostatic test and inspector visits are needed, access in the boiler room, and whether a temporary boiler must carry the load. A gasket and controls repair on a small firetube unit and a tube replacement on a large watertube unit sit at opposite ends of that range, so a useful boiler repair estimate starts from the inspection report and the boiler data rather than a rule of thumb.

The state’s own charges are small and fixed. Under 42 CSR 3, a Division inspection costs $100 for a boiler with less than 100 square feet of heating surface, $150 for 101 to 500 square feet and $175 above 500 square feet or for a forced flow steam generator; processing an insurer’s inspection report costs $35; the permit to operate costs $35; and reviewing a permit to install or a permit extension costs $70. West Virginia repealed its state prevailing wage law in 2016, so public owners such as counties and school systems price boiler work without a state wage schedule, although federally funded projects follow federal wage rules.

How much is boiler maintenance compared with repair? Scheduled maintenance, covering the annual inspection outage, burner tuning and combustion analysis, safety device testing and water treatment review, costs far less than the repairs it prevents, and it keeps the unit inside its permit year. Paul Industries prices maintenance as a fixed annual program and repairs from the inspection findings, with parts, labor, testing and any temporary steam shown as separate lines.

Who repairs boilers in West Virginia?

Paul Industries repairs boilers in West Virginia, working at plants, hospitals, universities and public buildings across the state from its headquarters at 256 Shore Drive in Kilmarnock, Virginia. The company, formerly based in northern New Jersey and then Pennsylvania, is an East Coast contractor that takes work across West Virginia, the Mid-Atlantic and all 50 states.

For commercial boiler repair West Virginia owners need, from a hospital heating plant to a county courthouse, and for industrial steam plants serving chemical and manufacturing processes, Paul Industries diagnoses faults, retubes firetube boilers, replaces watertube tubes, repairs drums and headers under the R program with the inspector involved, rebuilds burners and controls, tests safety devices, and supplies and installs replacement boilers. The national picture of boiler faults and repair methods is on the boiler repair page, and the headquarters state’s rules are covered under boiler repair in Virginia. Plants with sites across the border compare West Virginia’s permit cycle with boiler repair in Pennsylvania, where the inspection system and operator rules differ.

The work rarely stops at the boiler itself. Paul Industries also provides process piping in West Virginia for steam headers and condensate systems, industrial welding services in West Virginia for pressure-part and structural repairs, pressure vessel fabrication in West Virginia for blowdown tanks, flash tanks and receivers, and tank fabrication in West Virginia for condensate and fuel storage.

Boiler repair from Paul Industries for West Virginia plants

Paul Industries repairs, overhauls, converts and replaces steam and hot water boilers at West Virginia facilities, and plans each job around the permit to operate, the annual inspection and the National Board records the inspector and insurer expect. Owners choose the route that fits: repair of the existing boiler, supply of a replacement boiler with startup, or design-build of a complete boiler plant with its piping, feedwater, fuel train and controls. The West Virginia page sets out the wider range of process work Paul Industries delivers in the state. To plan a repair, send the boiler data and the last inspection report and request a quote.

Standards referenced: W. Va. Code 21-3-7, Regulation of operation of steam boilers · 42 CSR 3, High-Pressure Steam Boiler and Forced Flow Steam Generator Requirements · ASME Boiler and Pressure Vessel Code Section I · ASME Boiler and Pressure Vessel Code Section IV · National Board Inspection Code (NBIC) Parts 1 to 4 · National Board NB-132 Recommended Administrative Rules · 45 CSR 13, WV DEP air permits for stationary sources · 45 CSR 2, particulate matter from fuel burning units · 40 CFR 60 Subpart Dc · 40 CFR 63 Subparts DDDDD and JJJJJJ

Frequently asked questions

Who provides boiler repair Charleston, WV hospitals and Kanawha Valley plants depend on?

Paul Industries repairs steam and hot water boilers in Charleston and along the Kanawha Valley, from hospital and government heating plants to process steam boilers at chemical plants along the Kanawha River. Repairs at chemical plants are usually scheduled into the plant’s turnaround so the boiler outage and the process outage overlap. Each repair is documented for the inspector and insurer. Call 201-450-8280 to plan the work.

Does Paul Industries repair boilers in Wheeling, Weirton and the Northern Panhandle?

Yes. Paul Industries repairs and replaces industrial and institutional boilers in Wheeling, Weirton and the rest of the Northern Panhandle, including heavy-duty process boilers at metals and manufacturing plants and heating plants at hospitals and schools. The work follows the same West Virginia permit cycle as anywhere in the state, with the inspection outage used as the repair window.

Who repairs boilers in Huntington, Parkersburg and the Ohio Valley?

Paul Industries repairs boilers in Huntington, Parkersburg and the plants along the Ohio River between them, including process steam boilers at chemical and polymer manufacturers and heating boilers at hospitals and campuses. Plants with sister sites across the river in Ohio get the same repair approach on both sides, with each state’s permit and inspection paperwork kept separately.

What is a WV serial number on a boiler?

The WV serial number is the identifying number the Division of Labor assigns to a steam boiler after its final inspection, written in the form W, then the number, then W. An inspector marks it on the boiler where the ASME Code places identification, and the owner keeps it visible at all times. Insulation and casing repairs are arranged so the number stays uncovered.

Does a WV boiler permit need to be renewed after a repair?

A routine repair leaves the current permit in place, and the next annual inspection renews it as usual. A repair that changes the boiler’s design, such as a rerate to a different allowable pressure, is an alteration, and the permit to operate is updated because it states the maximum pressure. A boiler that was condemned or had its permit suspended runs again only after an inspector confirms compliance and the Commissioner reinstates the permit.

Can a West Virginia boiler run while its permit extension is pending?

An owner who cannot complete inspection and repair before the permit expires applies in writing for an extension of up to 60 days, supported by statements from the inspector or special inspector and the insurer. The Commissioner decides each request for good cause, and the total of extensions is capped at 120 days a year. Paul Industries schedules repairs inside the permit year so an extension is a fallback rather than the plan.

Who inspects a boiler after a repair in West Virginia?

The inspector who covers the boiler: a Division of Labor inspector when the boiler has no insurance coverage, or the insurance company’s special inspector when it does. For a welded pressure-part repair the inspector is consulted before the work and accepts it afterwards, usually by witnessing the hydrostatic test. Paul Industries arranges that sequence and provides the repair report, weld records and test results.

What happens if an insurer refuses coverage on a West Virginia boiler after inspection?

Under 42 CSR 3 the insurance company notifies the Division of Labor immediately and sends a list of the defects its special inspector found. The boiler then needs those defects repaired and accepted before coverage or a state inspection lets it keep its permit. Paul Industries works from the defect list, agrees each repair method with the inspector, and documents the work so the boiler returns to the permit cycle.

How do boiler inspection requirements by state compare for a company with sites in West Virginia and Ohio?

Each state sets its own permit, inspection interval and fees, while the technical standards for repairs, the NBIC and the ASME Code, are shared. West Virginia issues a 12-month permit to operate for steam boilers above 15 psi and inspects them yearly; neighboring states differ in which boilers they cover and how often. Paul Industries keeps each site’s records in the format its jurisdiction expects.

What should a plant send Paul Industries to get a boiler repair priced in West Virginia?

Send the boiler make, model, type and National Board or WV serial number, the steam pressure and capacity, the fuel, the last inspection report and any insurer recommendations, recent water treatment results and a description of the fault or alarm history. Photos of the nameplate, the posted permit and any visible damage help. Paul Industries uses that information to plan the diagnostic visit and price the repair line by line.

How long does a firetube retube take at a West Virginia plant?

A firetube retube runs from several days to a few weeks of outage, depending on the boiler size, the number of tubes, whether the tubes are rolled or welded, and how much tube sheet repair is found once the old tubes are out. Tubes are ordered before the outage starts, and the hydrostatic test and inspector acceptance are booked in advance. Paul Industries sets the outage plan so steam is restored as soon as the boiler passes its test.

Can a used boiler from another state be installed in West Virginia?

A used boiler is installed under the same permit to install process as a new one, applied for at least 15 days before it is set, and the rule adopts the National Board provisions on secondhand and reinstalled boilers. Condemnation elsewhere carries over, so the history is checked first. Paul Industries reviews the unit’s data report, inspection history and condition before purchase, then installs, tests and prepares it for its first inspection in the state.

Does a burner replacement on a West Virginia boiler need an air permit change?

Sometimes. A like-for-like burner replacement on a gas-fired boiler often fits within the existing air permit, while a change of fuel, a larger firing rate or a new unit is reviewed under West Virginia’s 45 CSR 13 permit rule and, for larger units, federal rules such as 40 CFR 60 Subpart Dc. Paul Industries provides the burner data, emissions guarantees and firing rate the plant needs for that review before the burner is ordered.

What does a low-water cutoff test involve during a West Virginia inspection?

The inspector checks that the low-water cutoff stops the burner when the water level falls to the cutoff point, usually by an evaporation or blowdown test with the boiler firing, and confirms the float chamber and connections are clear of sludge. A cutoff that fails is repaired or replaced before the boiler returns to service. Paul Industries tests every safety device after a repair and records the results for the inspector.

Is a hot water heating boiler in a West Virginia school covered by the state boiler permit?

The state permit applies to steam boilers carrying more than 15 psi and forced flow steam generators, so a hot water heating boiler in a school sits outside it. Its repairs still follow ASME Section IV and the NBIC, and the insurer’s requirements. Paul Industries repairs and replaces school heating boilers to the same standard and with the same records as permitted steam boilers.

How are boiler repairs scheduled at a West Virginia chemical plant turnaround?

The boiler outage is aligned with the plant turnaround so the annual inspection, the repairs and any work on steam users happen in one window. Inspection findings from the previous year, insurer recommendations and water treatment data set the expected scope, and tubes, refractory and relief valves are on site before the boiler comes down. Paul Industries plans the boiler work as one package inside the turnaround schedule.

What records should a West Virginia facility keep after a boiler repair?

Keep the NBIC repair or alteration report, the welding procedure and welder records, nondestructive examination results, the hydrostatic test record signed by the inspector, relief valve data, the combustion and safety device test sheets, and the current permit to operate. Those records support the next inspection, the insurer’s file and any future repair. Paul Industries hands them over as one package at the end of the job.

Boiler down, or an inspection finding to clear in West Virginia?

Send the boiler type, size and serial number, the last inspection report, the fuel and a description of the fault. Call 201-450-8280 or request a quote.