Paul Industries engineers, builds, commissions and maintains data center cooling in Rhode Island, from the computer room air handlers and containment on the white floor to the chillers, cooling towers, dry coolers and economizer exchangers that carry the heat outdoors. Rhode Island hands a cooling plant three problems at once: muggy summer air that keeps the wet bulb high, salt-laden wind off Narragansett Bay and Block Island Sound, and electricity that costs about two thirds more than the national commercial average. From headquarters at 256 Shore Drive in Kilmarnock, Virginia, Paul Industries accepts cooling projects from Woonsocket to Westerly, in all 50 states and at sites abroad through its international projects.

Request a quote or call 201-450-8280

Headquarters 256 Shore Drive, Kilmarnock, Virginia
Providence design wet bulb 77.4 F exceeded 0.4% of hours (PVD, 2021-2025)
Humid hours About 1,200 hours a year with dew point at or above 65 F, statewide
Commercial power 23.68 cents/kWh in Rhode Island vs 14.04 US (EIA, Jan-Aug 2026)
Coastal wind design Up to 149 mph for Risk Category IV on Block Island (RISBC-1)
Reviewed November 2026

What sets data center cooling in Rhode Island apart?

Data center cooling in Rhode Island is set apart by moisture more than heat. Providence’s airport recorded a 0.4 percent design wet bulb of 77.4 F between 2021 and 2025, and every Rhode Island station logged roughly 1,200 hours a year with the dew point at or above 65 F, about twice the figure for Burlington, Vermont over the same years. A plant built for this state removes water as well as heat from the air for a large share of the summer.

Three more facts shape the design. Commercial power averaged 23.68 cents a kilowatt-hour across January to August 2026, so every fan, pump and compressor kilowatt costs about two thirds more than the national average. Narragansett Bay reaches all the way up to Providence, so outdoor coils and fasteners in the capital, as well as on the shore, face chloride exposure that inland plants never see. And the Rhode Island Building Code sets wind speeds town by town that reach 149 mph for essential facilities on Block Island, which governs how a dry cooler or tower is anchored to a roof.

How chillers, air handlers, aisle containment and economizers work in general is explained on the national data center cooling systems page. This page stays with Rhode Island: what five weather stations say, how humidity and salt change equipment choices, what the state’s wind table asks of rooftop heat rejection, what power costs, and how Paul Industries upgrades cooling in a room that keeps running.

Which Rhode Island buildings hold computer rooms today?

Computer rooms in Rhode Island today usually sit inside larger buildings rather than on stand-alone campuses: hospital and health system rooms in Providence, university research computing on College Hill and in Kingston, state agency rooms, insurance and finance operations along Route 95, and the server rooms of manufacturers at Quonset and in the Blackstone Valley. Research computing gives a sense of the density involved; Brown University’s Oscar cluster has more than 300 multi-core nodes and more than 800 NVIDIA GPUs, from Titan RTX cards up to B200 accelerators.

That pattern decides how cooling projects run. A computer room of that kind shares chilled water, condenser water, emergency power and roof space with the building around it, so a cooling upgrade is also a building project with tenants, occupied floors and a facilities team that answers to more than the IT group. Siting rules for new large facilities, the state bills on data center incentives and town zoning actions are explained on the data center mechanical contractors in Rhode Island page; this page deals with the cooling plant itself.

Providence, Smithfield, Westerly, Newport and Block Island: the design weather

Five Rhode Island airports, read hourly over 2021 through 2025, show how the design point moves between the Providence metro, the inland northwest, the South County shore, Aquidneck Island and Block Island. Each hourly wet bulb below was derived psychrometrically from the recorded dry bulb, dew point and barometric pressure.

Design weather at five Rhode Island airports (hourly records, 2021 to 2025)
StationDry bulb exceeded 0.4% of hoursWet bulb exceeded 0.4% of hoursHours per year at or above 90 FHours per year at or below 10 FColdest hour
Providence, T.F. Green in Warwick (PVD)90 F77.4 F4221-9 F
North Central State, Smithfield (SFZ)89 F78.1 F2455-11 F
Westerly (WST)85 F75.7 F229-6 F
Newport State, Middletown (UUU)84 F75.9 F314-7 F
Block Island (BID)82 F75.1 F06-5 F

The inland stations carry the hardest summer. Smithfield, which serves the Route 7 and Route 146 corridors toward Lincoln and Woonsocket, logged a 78.1 F design wet bulb, above every other station in the table, and Providence logged a hottest hour of 100 F. The shore stations rarely touch 90 F, yet their wet bulb still sits above 75 F because the sea air is so moist, so a cooling tower in Newport or Westerly is sized nearly as large as one in Cranston. Smithfield’s figures rest on about 4.6 years of usable hours.

For a data center, Rhode Island summers also swing hard from year to year. Providence logged 84 hours at or above 90 F in 2022 and just 2 in 2023, so Paul Industries sizes heat rejection to the 0.4 percent design values and then tests each selection against a summer like 2022.

Why humidity sizes a Rhode Island cooling plant

Humidity sizes a Rhode Island cooling plant because outdoor air stays above the ASHRAE recommended dew point of 59 F for roughly 1,840 to 2,070 hours a year across the five stations, and every pound of that moisture that reaches the white floor has to be condensed out by a coil. Dew points at or above 70 F, the stickiest July and August nights, added another 460 to 520 hours a year in the record.

Moisture reaches a data room through outdoor air brought in for ventilation and pressurization, through doors to loading docks and corridors, and through leaky envelopes in older mill and office buildings. A plant that runs its chilled water warm for efficiency can lose its ability to dehumidify, because a coil fed with 60 F water barely reaches the dew point of the air it handles. Paul Industries solves that by treating ventilation air separately in a dedicated outdoor air unit with a deep, cold coil, keeping the room coils dry and warm, and sealing pipe penetrations and doors so the room holds a slight positive pressure without pulling in Bay air.

Condensation outside the room matters as much. Chilled water piping, valves and pump casings in Rhode Island mechanical rooms sweat for much of the summer unless they carry closed-cell insulation with sealed seams and vapor-tight fittings. Wet insulation corrodes carbon steel pipe from the outside and drips onto electrical gear, so Paul Industries insulates every new cold surface, seals joints and fittings, and checks for wet spots during the first humid week after startup.

How many economizer hours does a Rhode Island room earn?

Economizer hours in Rhode Island cover a little over half the year for a plant that wants 60 F chilled water and close to three quarters of it for a plant that accepts warmer water. Assuming a 7 degree cooling tower approach and a 3 degree plate exchanger approach, a 55 F wet bulb yields chilled water near 65 F, a temperature that keeps air-cooled servers inside the ASHRAE recommended inlet range once containment stops hot air from mixing back.

Economizer weather by station: percent of hours under each wet bulb limit
StationWet bulb at or below 50 FAt or below 55 FAt or below 60 FLongest unbroken run at or below 32 F
Providence (PVD)52.4%61.5%72.1%154 hours
Smithfield (SFZ)56.1%64.6%74.2%186 hours
Westerly (WST)53.2%62.2%72.4%169 hours
Newport (UUU)52.8%62.1%72.8%171 hours
Block Island (BID)52.3%61.3%72.3%116 hours

Two conclusions follow. Each 5 F step in the wet bulb an owner can accept adds roughly ten percentage points of economizer time, about 800 to 900 hours a year, so raising the chilled water setpoint pays more here than almost any equipment change. And the state’s freezing spells are short: the longest unbroken stretch at or below 32 F ran from 116 hours on Block Island to 186 hours in Smithfield, about a week at most. Freeze protection still matters, but a Rhode Island economizer spends its winters cycling around freezing rather than sitting deep below it, so controls that switch cleanly between modes earn more than heavy freeze margins.

Paul Industries writes the sequence that hands load from free cooling to blended operation to chillers so supply temperature holds steady, stages tower fans and plate exchanger bypass for those near-freezing nights, and raises setpoints a step at a time while watching rack inlet temperatures. Air-side economizers that bring outdoor air straight into the room are a harder sell in this state, because the same humid hours that limit waterside economizers would load the room with moisture and salt.

Salt air on condenser and dry cooler coils, from the Bay to Block Island

Salt air attacks the outdoor heat rejection of a Rhode Island data center first at the coil fins, where thin aluminum against copper tube forms a galvanic pair that chloride-laden moisture drives into corrosion. A bare-fin coil exposed to onshore wind loses fin contact and capacity well before its compressors or fans wear out, and the loss shows up as rising condensing pressure on the hottest afternoons, when the margin is smallest.

Specification decides most of the outcome. For sites near the shore, from East Providence and Bristol down to Narragansett, Newport and Westerly, Paul Industries specifies factory-applied coil coatings rated for coastal exposure or coils with corrosion-resistant fin construction, stainless or coated fasteners and cabinet hardware, sealed electrical enclosures on fans and controls, and dielectric isolation wherever dissimilar metals meet on pipe supports and curbs. Units are set where buildings shield them from the prevailing onshore wind when the roof allows, and wider fin spacing is chosen where salt and pollen would load a tight coil.

Maintenance closes the loop. Coastal coils need a fresh-water rinse on a regular schedule, gentle enough to clean without bending fins, plus periodic checks of coating condition and fin bond. Paul Industries writes those tasks into the turnover maintenance plan for each Rhode Island cooling plant and performs them under service agreements, so coil capacity measured at startup is still there in year ten.

Wind design for rooftop heat rejection under the Rhode Island Building Code

Rooftop heat rejection on a Rhode Island data center is anchored to the wind speeds in the Rhode Island Building Code, which replaces the national wind maps with a table of basic wind speeds for every city and town at each risk category. The code took effect in its current form on December 1, 2025, built on the 2021 International Building Code, and flags a wind-borne debris region along the coast.

Basic wind speed and ground snow load for selected Rhode Island towns (RISBC-1)
TownRisk Category IIRisk Category IVGround snow loadCoastal debris flag
Woonsocket122 mph135 mph40 psfNone listed
Smithfield123 mph136 mph40 psfNone listed
Providence125 mph138 mph30 psfWithin a mile of the coastal high water line
Warwick127 mph139 mph30 psfWithin a mile of the coastal high water line
West Greenwich127 mph139 mph35 psfNone listed
North Kingstown129 mph141 mph30 psfDebris region at 140 mph and above
Newport131 mph144 mph30 psfDebris region at 140 mph and above
Westerly137 mph142 mph30 psfDebris region at 140 mph and above
New Shoreham (Block Island)134 mph149 mph25 psfDebris region at 140 mph and above

The risk category depends on what the building houses: an ordinary office or colocation building usually falls in Risk Category II, while a hospital or emergency operations room that must keep working after a storm is often placed in Risk Category IV, and the design professional of record sets the category. Paul Industries designs curbs, dunnage, tie-downs and equipment anchorage to the wind speed for that category and town, confirms the unit manufacturer’s rating for the resulting loads, and protects exposed controls and refrigerant lines where the debris region applies. Inland sites trade some wind for snow; Woonsocket, Smithfield and Lincoln carry 40 psf ground snow, which affects drift loads against tall dry coolers and the clearance needed under coil intakes.

What do Rhode Island kilowatt-hours add to a cooling plant’s running cost?

EIA data put the Rhode Island commercial average at 23.68 cents per kWh for the year to date through August 2026, compared with a US figure of 14.04 cents and a New England figure of 23.33. Industrial customers paid 21.57 cents, more than in any other New England state and about 2.4 times the national industrial average of 9.09 cents.

At those prices a 100 kW cooling load that never switches off burns 876,000 kWh a year, costing about $207,437 at the commercial average and about $188,953 at the industrial average, compared with about $122,990 at the national commercial price. Trimming plant efficiency by 0.1 kW per ton across a 300-ton average load removes 30 kW from the meter around the clock, about 262,800 kWh and $62,231 a year at the Rhode Island commercial price. Utility tariffs add demand charges on top of energy, so Paul Industries works every efficiency case from the owner’s own bills, interval data and rate class, and shows the payback beside the price.

Rhode Island Energy commercial rates, Pascoag and Block Island: who serves the meter

Rhode Island Energy serves most of the state; PPL completed its purchase of The Narragansett Electric Company on May 25, 2022, which answers a question owners still ask: is Rhode Island Energy the same as National Grid? It is the same wires company under new ownership and a new name. Two quasi-municipal districts serve their own territories: the Pascoag Utility District in the Pascoag and Harrisville villages of Burrillville, and the Block Island Utility District, whose island has drawn mainland power through a single undersea cable since May 2017 and falls back on diesel generation when that cable is out. Wholesale power and the regional transmission system are run by ISO New England across the six states.

The utility shapes a cooling design through its demand charges, the spare capacity behind the meter and its outage history. A large chiller or CDU addition often needs a service upgrade with a long lead time, and a site on Block Island designs for the day the cable trips. Paul Industries plans ride-through to suit: UPS power for pumps, fans and controls, quick-restart chillers, and stored chilled water where the outage record or demand charges justify it.

Which heat rejection fits a Rhode Island site?

Heat rejection for a Rhode Island site is chosen by load, roof space, water use and salt exposure, and each common option has a clear place in the state.

Heat rejection options for Rhode Island computer rooms
OptionWhere it fits in Rhode IslandRhode Island watch points
Water-cooled chillers with open cooling towersLarger plants in Providence, Warwick and Cranston buildings that already run condenser waterDesign wet bulb of 77 F to 78 F inland; makeup water, treatment and Legionella control; winter basin heat for near-freezing cycling
Air-cooled chillers with integral free coolingMid-size rooms with roof space and no tower waterCoastal coil coating; wind anchorage to the town’s speed; condensing pressure on 90 F afternoons
Dry coolers on a glycol loopWarm-water and liquid-cooled rooms; sites that want no makeup waterLimited summer capacity in muggy, warm hours; glycol strength for single-digit nights; salt exposure
Adiabatic or hybrid coolersOwners who want little water use but extra capacity on the worst afternoonsHigh wet bulb limits the boost; water quality on pads or sprays near the shore
Closed-circuit fluid coolersPlants that need tower performance with a sealed process loopSpray water treatment; casing and coil materials for chloride exposure

Two Rhode Island Mechanical Code amendments narrow the field. Section 1101.4.1 prohibits using potable water as an open-loop, single-pass heat exchange fluid for the refrigeration cycle of HVAC equipment, so a city-water once-through backup for a computer room unit is off the table and emergency cooling has to come from a closed loop, a second chiller or storage. Section 1105.3 requires a refrigerant detector in every machinery room, with an audible and visual alarm set no higher than the refrigerant’s TLV-TWA value, which applies whenever new chillers go into an enclosed plant room. Paul Industries designs to both from the first layout.

Cooling upgrades inside occupied Providence and Warwick buildings

Upgrading cooling in a Rhode Island room that stays live starts with proving that the remaining equipment can carry the load while one unit is out, then moving one piece at a time. Paul Industries surveys the existing chillers, air handlers, pumps and controls, logs a week of rack inlet and loop temperatures, and writes a step-by-step method of procedure that the owner signs before any valve moves.

The season helps. Because the wet bulb stays at 50 F or lower for over half the year, a waterside economizer or temporary cooling can carry most rooms from November through April while a chiller is replaced, and that is when Paul Industries schedules the heaviest work. New branches join live mains through hot taps and line stops, spools built ahead of time keep each shutdown short, and every new unit runs on test before it carries the room. In older mill buildings from Pawtucket to the Blackstone Valley, Paul Industries checks floor loading, freight elevator size and rigging paths before equipment is ordered, because a chiller that cannot reach the roof is the most expensive mistake on a retrofit.

Related work often rides along: chiller repair in Rhode Island for machines kept in service, data center cooling towers for condenser water plants, and data center liquid cooling in Rhode Island when new racks outgrow air. Testing and turnover follow the plan described under data center commissioning in Rhode Island.

How much does data center cooling in Rhode Island cost?

The cost of data center cooling in Rhode Island depends on IT load, redundancy, heat rejection type, roof and rigging access, coastal specification, wind anchorage and the share of work done beside running servers. Paul Industries prices each room from those drivers, since they move installed cost more than equipment price does.

The site conditions that drive a Rhode Island estimate are the design wet bulb and dew point for the site’s station, the redundancy level, the supply air or water temperature the IT equipment accepts, the town’s wind speed and snow load, salt exposure, and the outage windows the room can give. Operating cost is easier to pin down: at the 2026 commercial average, each 100 kilowatts of continuous load costs about $207,437 a year in electricity, so a design that cuts fan, pump and compressor power by a fifth is often worth more over ten years than the whole equipment budget. Owners receive a budget figure drawn from similar rooms early on, then a fixed price when drawings, load data and shutdown windows are agreed.

Who installs data center cooling in Rhode Island?

Paul Industries installs data center cooling in Rhode Island, carrying design, equipment supply, installation, piping, controls, testing, startup and service under one contract for hospitals, universities, insurers, state agencies, manufacturers and colocation operators. Owners choose design-build, complete installation to their engineer’s drawings, or supply-only delivery of chillers, dry coolers, pump skids and fill packages.

Paul Industries, formerly based in northern New Jersey and then Pennsylvania, now runs its work from Kilmarnock, Virginia, and the Northeast has stayed a steady part of it. Owners with rooms in more than one state can compare this page with data center cooling in Virginia, the headquarters state, and with data center cooling in Massachusetts and Connecticut next door. The Rhode Island hub lists the other systems Paul Industries builds in the state, and the New England page sets the six states side by side.

Rhode Island cooling projects with Paul Industries

Paul Industries engineers, builds and maintains cooling plants for Rhode Island computer rooms: chillers and towers sized to a 78 F wet bulb, dehumidification that keeps Bay moisture off the white floor, coastal-grade coils, rooftop anchorage to the town’s wind speed, and controls that bank every economizer hour the climate offers. Share the room’s load, redundancy, town and utility to start a scope and budget. Call 201-450-8280 or request a quote.

Standards referenced: ASHRAE TC 9.9 Thermal Guidelines for Data Processing Environments · ASHRAE 90.4 · Rhode Island Building Code (RISBC-1, 2021 IBC with Rhode Island amendments) · Rhode Island Mechanical Code (RISBC-4, 2021 IMC with Rhode Island amendments) · Rhode Island Energy Conservation Code (RISBC-8, 2024 IECC) · ASCE 7 · NFPA 90A

Frequently asked questions

Who cools hospital and university computer rooms in Providence?

Paul Industries provides data center cooling in Providence, from hospital and university computer rooms on College Hill to office and agency rooms downtown. Work covers chillers, towers, CRAH units, containment, dehumidification and controls, planned around Providence’s 77.4 F design wet bulb and 125 mph Risk Category II wind speed. Paul Industries surveys the room, proposes the upgrade path and installs it while the room stays live.

Does Paul Industries take cooling work in Warwick, Cranston and Kent County?

Paul Industries takes cooling work in Warwick, Cranston, West Warwick, East Greenwich and across Kent County, including rooms near T.F. Green and the Route 95 office corridor. Warwick’s code wind speed is 127 mph for Risk Category II and 139 mph for Risk Category IV, and much of the city lies within the coastal debris area, so rooftop units are anchored and protected to match. Paul Industries designs each plant, installs it, brings it online and keeps it running.

Who handles server room cooling at Quonset and in North Kingstown?

Paul Industries handles server room and process computer room cooling for manufacturers and tenants at the Quonset Business Park and across North Kingstown. Those sites sit on the water, so outdoor coils get coastal-grade coatings and stainless or coated hardware, and rooftop equipment is anchored for North Kingstown’s 129 mph Risk Category II wind speed. Paul Industries installs the cooling, writes the coil care plan and services it under agreement.

Which cooling suits a room in Smithfield, Lincoln or Woonsocket?

Rooms in Smithfield, Lincoln and Woonsocket face the hottest wet bulb in the state, 78.1 F at the Smithfield airport, along with the most single-digit nights and a 40 psf ground snow load. Water-cooled or air-cooled chillers sized to that wet bulb, with a waterside economizer for the cold months, suit most of them. Paul Industries checks drift clearance around dry coolers and sizes glycol for the inland lows.

Does Paul Industries cool computer rooms in Newport, Middletown and on Aquidneck Island?

Paul Industries cools computer rooms in Newport, Middletown and Portsmouth, where salt exposure and a 131 mph Risk Category II wind speed in Newport shape every outdoor unit. Summer heat is milder there, with the Newport airport reaching 90 F for only about 3 hours in a typical year, but the wet bulb still reaches 75.9 F. Paul Industries specifies coastal coils, sealed controls and wind-rated anchorage and maintains them after startup.

Can a data room in Westerly or South County run on dry coolers?

Dry coolers can carry a Westerly or South County data room through most months, especially one built around warm-water liquid cooling, because temperatures at the Westerly airport topped 90 F for about 2 hours a year. Muggy summer hours still limit a dry cooler’s capacity, so a trim chiller or an adiabatic stage usually backs them up. Paul Industries sizes the split from the station data and installs the full loop.

What coil protection does an RI data center near Narragansett Bay need?

An RI data center near Narragansett Bay or the South County shore needs outdoor coils with a factory coating rated for coastal exposure or corrosion-resistant fin construction, stainless or coated fasteners, sealed fan and control enclosures, and dielectric breaks where dissimilar metals meet. Coils also need a scheduled fresh-water rinse. Paul Industries specifies those details at purchase, installs the units and writes the rinse and inspection tasks into the service plan.

Is Rhode Island Energy the same as National Grid for a cooling project?

Rhode Island Energy is the former Narragansett Electric Company, which National Grid owned until PPL completed its purchase on May 25, 2022. For a cooling project the change matters chiefly in who reviews service upgrades and which tariffs apply. Paul Industries gathers a year of bills and interval data, checks service capacity before adding chiller or CDU load, and coordinates the utility application with the project schedule.

How warm can chilled water run in a humid Rhode Island data hall?

Most Rhode Island data halls with good containment run well on chilled water between 55 F and 65 F, well above the 42 F to 45 F that older Rhode Island plants often still deliver. Warmer water adds economizer hours, about ten percentage points of the year for each 5 F of wet bulb accepted, but it weakens dehumidification, so ventilation air is dried separately. Paul Industries lifts the setpoint gradually while logging rack inlet temperature and room dew point.

How much summer moisture does a Rhode Island computer room have to remove?

A computer room on the Rhode Island grid faces outdoor dew points above 59 F, the ASHRAE recommended ceiling, for about 1,840 to 2,070 hours a year, with roughly 460 to 520 hours above 70 F. The moisture load depends on how much outdoor air the room takes in and how tight its envelope is. Paul Industries measures infiltration and ventilation rates, then sizes a dedicated outdoor air unit or reheat coil to hold the room dew point.

How much electricity money does cooling burn in a Rhode Island computer room each year?

A continuous 100 kW cooling load runs about $207,437 a year at Rhode Island’s January to August 2026 commercial average of 23.68 cents per kWh, and about $188,953 at the industrial average of 21.57 cents, based on EIA data. Real bills add demand charges, so Paul Industries builds the figure from the site’s own Rhode Island Energy or district utility bills before comparing upgrade options.

How does the Rhode Island wind table affect a rooftop dry cooler?

The Rhode Island Building Code assigns each town a basic wind speed by risk category, from 122 mph in Woonsocket to 137 mph in Westerly for Risk Category II, and up to 149 mph on Block Island for Risk Category IV. Those speeds set the uplift and overturning loads on a rooftop dry cooler, its curb and its tie-downs. Paul Industries designs the anchorage to the right speed and confirms the unit’s rating.

Can city water be used as emergency cooling for a computer room in Rhode Island?

Rhode Island’s Mechanical Code prohibits using potable water as an open-loop, single-pass heat exchange fluid for the refrigeration cycle of HVAC equipment, so city-water once-through backup for a computer room unit is ruled out. Emergency cooling comes from a second chiller, a closed glycol loop, chilled water storage or a connection for a temporary chiller. Paul Industries designs and installs the backup path that fits the room.

How should a Rhode Island cooling plant ride through a hurricane or nor'easter outage?

A Rhode Island cooling plant rides through a storm outage when pumps, fans and controls stay on UPS, chillers restart quickly once generators pick up, and enough thermal mass or stored chilled water carries the room through the gap. Rooftop units must also survive the wind, which the town’s code speed governs. Paul Industries designs the ride-through sequence, anchors the equipment and proves the transfer before turnover.

Should a Rhode Island computer room reject heat with towers or dry coolers?

Towers win on large Rhode Island plants where summer condenser water has to stay as cold as possible against inland design wet bulbs of 77 F to 78 F. Dry coolers suit warm-water and liquid-cooled rooms and sites that want no makeup water, yet muggy summer hours limit their capacity. Many plants combine both or add an adiabatic stage. Paul Industries compares the options on the site’s own weather, water cost and roof.

How can a Rhode Island owner contract cooling work with Paul Industries?

Rhode Island owners can buy design-build, where one Paul Industries contract covers engineering, equipment, installation, startup and handover; complete installation to the owner’s engineered drawings; and supply-only delivery of equipment such as chillers, coolers and prepiped pump packages. Each route is priced separately so owners can compare them, and service agreements carry the plant after startup.

Which data center cooling requirements belong in a Rhode Island pricing request?

A useful Rhode Island pricing request lists today’s IT load and the five-year forecast, the redundancy target, the town and utility, drawings or photos of the room, roof and plant spaces, nameplate data for the current plant, a year of utility bills and the outage windows the room can give. Paul Industries returns a defined scope, a budget range and the energy savings worked on the site’s rate.

Planning cooling for a Rhode Island computer room?

Send the room’s IT load, redundancy level, town and electric utility, plus any plans on hand. Call 201-450-8280 or request a quote.