Paul Industries provides chiller repair in Wisconsin, diagnosing and repairing centrifugal, screw, scroll and absorption chillers, water-cooled and air-cooled, at dairy and food plants, breweries, manufacturers, hospitals, universities and data centers across the state. Wisconsin registers and inspects large refrigeration systems under its own state code, and those rules reach repairs as well as new installations, so a repaired chiller comes back with a state paper trail as well as a service report. Paul Industries, headquartered at 256 Shore Drive in Kilmarnock, Virginia, repairs, overhauls, retrofits and replaces chillers in Wisconsin with those records built in.

Request a quote or call 201-450-8280

Headquarters 256 Shore Drive, Kilmarnock, Virginia
State registration A1 or B1 chillers of 50 tons or more (SPS 345.30)
After a repair Register 20 business days before reactivation (SPS 345.30)
Periodic inspection At least every 36 months for A1 or B1 systems (SPS 345.31)
Coldest design point -25 F in the northern counties (SPS Table 363.0302)
Reviewed November 2026

How does Wisconsin change a chiller repair?

Wisconsin changes a chiller repair in three ways: the state’s mechanical refrigeration chapter, SPS 345, applies to repairs, replacement parts and alterations on existing systems and requires registered systems to be registered again before they return to service; the state’s winters, with design temperatures from 10 to 25 below zero, cause freeze damage that warmer states rarely see; and the state’s industries, from cheese and brewing to plastics and paper, run process chillers that cannot wait for spring. A repair plan in Wisconsin accounts for all three.

The general picture of chiller faults, symptoms and repair methods sits on the national chiller repair page. This page covers the Wisconsin layer: the state registration and inspection steps, the vessel and relief valve rules, the refrigerant rules that apply to older machines, the winter faults, and how repair is planned around Wisconsin plants and buildings.

Chiller repair in Wisconsin under the state refrigeration code

Chiller repair in Wisconsin falls under SPS 345, which requires state registration of any mechanical refrigeration system charged with an A1 or B1 refrigerant and rated at 50 tons or more (or the equivalent 50 horsepower or 50,000 volt-amperes), and of systems using A2, B2, A3 or B3 refrigerants at 10 tons, and which names any alteration or repair of a registered system as something to be registered too. The registration form goes in at least 20 business days before a system is reactivated after an alteration, repair or replacement, and the department or its authorized agent inspects the work within 45 business days after it is completed.

The chapter also sets a standard for the repaired parts themselves. Under SPS 345.11, replacement parts and the repaired portions of a system must comply with the chapter as it reads on the date of the repair, while the untouched parts of an older system keep the rules they were built under. Wisconsin designs to ASHRAE 15 through this chapter instead of chapter 11 of the International Mechanical Code, so relief valve sizing and discharge, machinery room ventilation and refrigerant detection are checked against the state’s adopted edition when a repair touches them.

Wisconsin rules that apply when a chiller is repaired
SituationRuleWhat it means for the repair
Repair or alteration of a registered A1 or B1 chiller of 50 tons or moreSPS 345.30 (1) (d) and (3) (b)Registration filed at least 20 business days before the system is reactivated
Inspection after the repairSPS 345.31 (2)Department or authorized agent inspects within 45 business days of completion
Permit to operateSPS 345.32Issued after a compliance determination; lists maximum operating pressure; three years for A1 and B1 systems
Periodic inspectionSPS 345.31 (3)At least every 36 months for A1 and B1 systems of 50 tons or more; 12 months for A2, B2, A3 and B3 at 10 tons or more
Outdoor comfort-cooling chillersSPS 345.31 (3) (a) 2Exempt from periodic inspection when used only for human comfort, located outdoors, with relief discharge at least 20 feet from building openings
Welded repair to an evaporator or condenser shellSPS 345.40 (2) (c) and SPS 341.60 to 341.64Repair made to the National Board Inspection Code under a National Board R certificate of authorization
Relief valve repairSPS 341.64Repair under an ASME or National Board VR authorization, with a repair nameplate attached
Adding R-22 or R-123SPS 345.70Equipment inspected and repaired if a leak is found or suspected before refrigerant is added

In practice, Paul Industries files the registration as soon as a repair scope on a registered machine is defined, prepares the machine and its records for the state inspection, and keeps the permit to operate, the inspection report and the repair records together in the owner’s file. Where a cooling-critical repair cannot wait for the full lead time, the code’s own note encourages owners and contractors to contact the department, and Paul Industries does so with the owner before the machine is opened.

Pressure vessel and relief valve repairs on a Wisconsin chiller

Pressure vessel and relief valve repairs on a Wisconsin chiller follow the state’s boiler and pressure vessel chapter, SPS 341, because a chiller’s evaporator and condenser shells are pressure vessels. The chapter’s scope note says that only its repairs and alterations subchapter applies to a pressure vessel in a mechanical refrigeration system, so the chiller’s shells are not on the state’s boiler and pressure vessel inspection cycle, but any welded repair to them follows the National Board Inspection Code and is made under a National Board R certificate of authorization for that scope.

Relief valves get their own rule. SPS 341.64 requires a safety or relief valve repair to be done under an ASME V, HV or UV code symbol stamp or a National Board VR stamp, and a metal repair nameplate is attached to the valve. Many owners replace relief valves rather than repair them, which avoids the repair nameplate and resets the valve’s service life; on low-pressure centrifugal machines, rupture disks and relief valves are often replaced together. Tube plugging and retubing are mechanical repairs rather than welded ones, but the same file records them. Vessel fabrication in the state is described on pressure vessel fabrication in Wisconsin.

Refrigerant rules for older Wisconsin chillers

Refrigerant rules for older Wisconsin chillers come from the state and from the EPA. Wisconsin’s SPS 345.70 applies to ozone-depleting refrigerants, which include R-22 and R-123: the refrigerant may not be used for cleaning, it is transferred to storage only with recovery equipment the department accepts, it may not be knowingly or negligently released, and before more of it is added the equipment has to be inspected and repaired if a leak is found or suspected, judged against the EPA’s yearly leak rate.

The federal rules set the supply. Production and import of R-22 ended on January 1, 2020, and existing machines run on reclaimed refrigerant; import allowances for R-123 end in 2030, after which existing low-pressure centrifugal machines rely on reclaimed and previously produced supply. For HFC machines such as R-134a and R-410A chillers, the EPA’s leak repair rule has applied since January 1, 2026 to appliances holding 15 pounds or more, with a 10 percent annual leak rate threshold for comfort cooling, 20 percent for commercial refrigeration and 30 percent for industrial process refrigeration, a 30-day deadline to fix a leak above the threshold, stretched to 120 days when the fix requires shutting down an industrial process, and verification tests after the fix. New comfort-cooling chillers have used refrigerants with a global warming potential below 700 since January 1, 2025.

Replacement refrigerants bring a Wisconsin-specific question. Some lower-GWP chiller refrigerants, such as R-1233zd(E) and R-513A, are in safety group A1, while others, such as R-1234ze(E) and R-454B, are A2L, a lower-flammability class. Because SPS 345 registers flammable groups at 10 tons and inspects them every 12 months, the refrigerant chosen for a retrofit or replacement decides which registration and inspection cycle the owner works under, and Paul Industries reviews that with the owner before a machine is selected.

Winter damage: the chiller faults Wisconsin’s cold produces

Wisconsin’s cold produces a set of chiller faults that owners in milder states rarely see: frozen and split evaporator tubes, burst condenser tubes in machines left wet in unheated rooms, failed low-ambient controls on air-cooled machines, frozen tower basins and makeup lines that starve a water-cooled chiller on its first spring start, and waterside economizer exchangers that freeze when a control valve sticks. State design temperatures range from 10 below on the Lake Michigan shore to 25 below in the north, and a single night at those temperatures finds every unprotected section of water.

Winter chiller faults in Wisconsin and how they are repaired and prevented
FaultTypical causeRepairPrevention
Split evaporator tubesWater left in an idle machine; low flow during a cold snapLeak test, plug or retube, dry and evacuate the refrigerant circuit, new chargeDrain or glycol-protect idle machines; flow and low-temperature safeties tested each fall
Water in the refrigerant circuitA failed tube on a water-cooled machineRefrigerant recovery, oil change, dehydration, filter-drier and component replacementEddy current testing to find thin tubes before they fail
Air-cooled chiller will not start or trips on low pressureLow ambient controls, fan staging, failed heatersControl repair, fan speed control, crankcase and enclosure heater replacementLow-ambient checks before winter
Frozen economizer plate exchangerStuck valve, glycol too weak, sensor faultPressure test, plate pack repair or replacementGlycol strength set from the county design temperature; valve and sensor checks
Spring start failure on a water-cooled chillerTower basin or makeup line frozen; condenser water strainers blockedTower and strainer repair, condenser flow restored, chiller restarted under loadBasin heaters, traced makeup lines, spring startup checklist

A frozen evaporator is the most expensive winter fault because water enters the refrigerant side, which turns a tube repair into a dehydration, oil and component job. Paul Industries finds the failed tubes by pressure and leak testing, plugs or retubes the bundle, recovers and replaces the contaminated refrigerant and oil, evacuates the circuit, and records each step for the state registration that follows. Tower-side faults lead into cooling tower repair.

Industrial chiller repair in Wisconsin plants

Industrial chiller repair in Wisconsin plants follows the production calendar of the state’s process industries: dairy and cheese plants cooling milk, whey and brine; breweries and beverage plants chilling wort, fermenters and packaging water; meat and food plants holding product temperatures; plastics molders and machine shops cooling molds, hydraulics and spindles; and paper mills, foundries and printers with process loads that run around the clock. A chiller fault in those plants stops product, so repairs are planned into shutdowns where possible and carried out quickly with parts on hand when not.

Process chillers in Wisconsin often run glycol through winter as well as summer, because the load is internal and constant. That gives them high annual run hours, which bring compressor, bearing and oil intervals around faster than a comfort machine’s, and it puts the glycol side, its strength, inhibitors and strainers, into every repair visit. Paul Industries pairs chiller refrigeration repair with the glycol and piping work around it, so a plant gets the machine and its loop back in service together. Single-line machines are covered on the process chillers page, and the plant’s piping on process piping in Wisconsin.

Commercial chiller repair in Wisconsin hospitals, universities and offices

Commercial chiller repair in Wisconsin hospitals, universities and office buildings is easier to schedule than in warmer states, because a long heating season leaves comfort chillers idle or lightly loaded for months, and most major repairs and overhauls are done between October and April. HVAC chiller repair in hospitals still needs care in winter: surgical suites, imaging rooms, pharmacies and data rooms carry cooling loads year round, and the remaining capacity, often an air-cooled machine or a waterside economizer, is checked before the main chiller is isolated.

University and campus plants in Madison, Milwaukee and the UW system’s other cities run central chilled water loops with several machines, and rebuilds are staged one machine at a time through the cold months. Office buildings and government facilities take larger repairs in winter and smaller ones on weekends in summer. Where a building’s heating plant shares the mechanical room, boiler repair in Wisconsin covers the hot side of the same plant.

Deciding between repair and replacement for a Wisconsin chiller

The decision between repair and replacement for a Wisconsin chiller rests on the refrigerant, the condition of the compressor and tubes, the leak history, the machine’s efficiency against a new one at Wisconsin power prices, and the registration and inspection path each option creates. A machine with a repairable fault on a current refrigerant usually earns its repair; an R-22 machine with frozen tubes and a history of leaks usually does not.

Repair or replace signals for a Wisconsin chiller
QuestionAnswer that favors repairAnswer that favors a new machine
Which refrigerant is in it?An HFC such as R-134a, or one of the newer low-GWP fluidsR-22 bought as reclaimed refrigerant, or R-123 with no supply plan beyond 2030
TubesFew plugged tubes; eddy current shows limited wall lossFreeze damage across the bundle; plugging near the design limit
CompressorFault limited to a bearing, seal, vane actuator or controlRepeat failures, rotor or impeller damage, a motor already rewound
Leak historyOne leak found, repaired and verifiedRepeated leak rate exceedances or repeated SPS 345.70 inspections before charging
EfficiencyMeasured performance close to ratingLarge gap to a new machine across the plant’s run hours
Registration pathRepair re-registered and inspected on the existing permitNew machine registered from the start, possibly in a different refrigerant group

Energy is part of the comparison even in a cool state. As an illustration with stated assumptions, a 400-ton chiller that improves by 0.20 kilowatts per ton after replacement and runs the equivalent of 2,000 full-load hours a year saves 160,000 kilowatt-hours, about $20,000 at Wisconsin’s 2024 average commercial price of 12.63 cents per kilowatt-hour (EIA). Process machines with longer hours save proportionally more. Paul Industries runs the calculation on the owner’s own logs and tariff before recommending either path.

How often should chiller tubes be cleaned in Wisconsin plants?

Chiller condenser tubes on open cooling tower systems in Wisconsin are usually cleaned once a year, before the cooling season, and more often where water quality or process loads foul them faster; evaporator tubes on closed loops need cleaning far less often. Machines that run all year on process loads often need a mid-year cleaning as well, scheduled into a plant shutdown.

The short tower season in much of Wisconsin is no reason to skip cleaning, because scale and biological fouling left in the tubes over winter harden and are harder to remove in spring. Paul Industries cleans tubes mechanically with rotating brushes or chemically where scale requires it, tests a sample or all tubes by eddy current, and records approach temperatures before and after so the owner sees what the cleaning recovered. Chiller service life depends heavily on that tube care, since a bundle that fails by pitting or freezing usually decides whether the machine is repaired or replaced.

Chiller maintenance requirements across a Wisconsin year

Chiller maintenance requirements across a Wisconsin year come from the manufacturer’s schedule, the state’s periodic inspection under SPS 345, the EPA’s leak rate and recordkeeping rules, and the seasonal work that keeps a machine safe through winter and ready for summer. The calendar below fits most comfort and process plants in the state.

A chiller service calendar for a Wisconsin plant
WhenTaskWhy it matters in Wisconsin
Each refrigerant additionLeak rate calculation; leak inspection before adding R-22 or R-123EPA rule for HFC systems; SPS 345.70 for ozone-depleting refrigerants
AutumnDrain or glycol-protect idle machines; test flow switches, freeze safeties and heatersPrevents split tubes when design temperatures reach 10 to 25 below
WinterOverhauls, eddy current testing, compressor inspections on comfort machinesLow load gives the longest outage windows of the year
SpringTube cleaning, tower startup, refill and pressure check, startup under loadFinds freeze damage before the first hot week
AnnuallyOil and refrigerant analysis, vibration readings, starter and motor checksHigh process run hours bring wear forward
At least every 36 monthsState periodic inspection for registered A1 and B1 systems; permit to operate kept currentRequired by SPS 345.31 for systems of 50 tons or more

Paul Industries offers that calendar as chiller service in Wisconsin under service contracts, with the state inspection dates, EPA records and seasonal tasks kept in one schedule.

What does chiller repair cost in Wisconsin?

Chiller repair cost in Wisconsin depends on what failed and which parts it takes, the tonnage and compressor type, the refrigerant and how much has to be recovered and replaced, access and rigging, whether temporary cooling is needed, and the season. A control or sensor repair costs a fraction of a compressor rebuild, and a frozen evaporator with water in the refrigerant circuit costs far more than a clean tube leak because of the dehydration, oil and component work that follows.

Owners also ask how much to replace a chiller. Replacement adds the new machine, rigging, piping and electrical changes, refrigerant recovery from the old unit, controls integration, and a new SPS 345 registration and inspection for the new system; tonnage, refrigerant and access move the total more than anything else. Paul Industries diagnoses first and then prices the repair with refrigerant, parts and labor as separate lines, adding a replacement budget next to any large repair so the two can be weighed.

Who provides chiller service and repair in Wisconsin?

Paul Industries provides chiller service and repair in Wisconsin, from diagnosis, leak repair, tube work and compressor overhauls to retrofits and complete replacements, at plants and buildings in Milwaukee, Racine and Kenosha, Madison, Green Bay, Appleton and Oshkosh, Sheboygan and Manitowoc, Wausau, Eau Claire and La Crosse, and in all 50 states. Machines of every major make are covered, among them Trane chiller repair, York chiller repair and Carrier chiller repair, and supplies and installs replacement machines where repair no longer pays.

Owners comparing practice across states can read chiller repair in Pennsylvania or the headquarters state page, chiller repair in Virginia. Chillers serving data halls are covered with their plant on data center cooling in Wisconsin.

Wisconsin chiller repair, overhaul and replacement from Paul Industries

From its Kilmarnock, Virginia headquarters, and with roots first in northern New Jersey and later in Pennsylvania, Paul Industries is an East Coast contractor that repairs, overhauls, maintains, supplies and installs chillers for plants, hospitals, campuses, offices and data centers across Wisconsin and in every other state. Each repair is handed back with the service report, refrigerant records and the state registration and inspection file in one place. To start, share the nameplate data, the refrigerant and its charge, recent alarms and logs, and the machine’s state registration status. Call 201-450-8280 or request a quote; for other services in the state see the Wisconsin page, which covers the rest of the work Paul Industries delivers in the state, and the Midwest page covers the neighboring states.

Standards referenced: ch. SPS 345 Mechanical Refrigeration (registration, inspection, permit to operate, ozone-depleting refrigerants) · ANSI/ASHRAE 15-2007 as adopted in SPS 345.40 · ch. SPS 341 subchapter VI and the National Board Inspection Code · SPS Table 363.0302 exterior design conditions · EPA Emissions Reduction and Reclamation rule, 40 CFR 84.106 · EPA Technology Transitions rule · Clean Air Act Section 608 · ASHRAE 34 refrigerant safety groups · AHRI 740 refrigerant recovery equipment

Frequently asked questions

Who handles chiller repair in Milwaukee, Racine and Kenosha?

Paul Industries handles chiller repair in Milwaukee, Racine, Kenosha and Waukesha for plants, hospitals, campuses and office buildings. Lakeshore counties carry the state’s warmest design summer, 89 degrees with a 77 degree wet bulb, and a 10-below winter design point, so condenser fouling in summer and freeze damage in idle machines in winter are both common repairs there. Send the make, model, refrigerant and alarm history to start.

Does Paul Industries provide chiller repair in Madison and Dane County?

Paul Industries provides chiller repair in Madison and Dane County for university and hospital central plants, laboratories, offices and food plants. Campus plants with several machines are rebuilt one machine at a time in the cold months, and research buildings with year-round loads are checked against the remaining capacity before any machine is isolated.

Who repairs chillers in Green Bay, Appleton and the Fox Valley?

Paul Industries carries out chiller repair in Green Bay, Appleton, Oshkosh, Neenah and Kaukauna, where paper mills, dairy and food plants, printers and manufacturers run process chillers year round. Those counties design to 15 below zero, so glycol strength, freeze safeties and low-ambient controls get checked at every winter visit.

Is chiller repair available in Wausau, Eau Claire and La Crosse?

Paul Industries takes chiller repair in Wausau, Stevens Point, Eau Claire, Chippewa Falls and La Crosse. With winter design points of minus 20 and minus 25, freeze protection comes first for idle and outdoor machines, and process chillers at food, dairy and manufacturing plants in central and western Wisconsin often run glycol year round.

Does a repaired chiller have to be registered with the state of Wisconsin again?

Under SPS 345.30, any alteration or repair of a currently registered mechanical refrigeration system is itself registered, with the form filed at least 20 business days before the system is reactivated. The department or its authorized agent then inspects the work within 45 business days of completion. Paul Industries files the registration once the repair scope is known and prepares the records for the inspection.

Which Wisconsin chillers must be registered and inspected?

The state registers machines holding A1 or B1 refrigerants once they reach a 50-ton rating, and machines using A2, B2, A3 or B3 refrigerants at 10 tons or more, through the Department of Safety and Professional Services. A1 and B1 systems are inspected at least every 36 months and the others every 12 months, with an exemption from periodic inspection for outdoor comfort-cooling systems whose relief valves discharge at least 20 feet from openings.

Can an evaporator shell be welded during a Wisconsin chiller repair?

A welded repair to an evaporator or condenser shell is a pressure vessel repair under SPS 341, which requires it to follow the National Board Inspection Code and to be made under a National Board R certificate of authorization for that scope. Tube plugging and retubing are mechanical repairs. Paul Industries records either kind of work in the file that goes with the SPS 345 registration.

What does Wisconsin require before R-22 is added to a leaking chiller?

SPS 345.70 requires equipment holding an ozone-depleting refrigerant, such as R-22 or R-123, to be inspected and repaired if a leak is found or suspected before more refrigerant is added, using the EPA’s yearly leak rate to judge whether repair is needed. The rule also forbids knowing or negligent release and requires recovery into storage with accepted equipment. Paul Industries finds and repairs the leak before charging.

Does the refrigerant in a new Wisconsin chiller change its inspection cycle?

The refrigerant’s safety group sets the SPS 345 thresholds. Lower-GWP refrigerants such as R-1233zd(E) and R-513A are group A1, while R-1234ze(E) and R-454B are A2L, a lower-flammability class, and Wisconsin registers flammable groups at 10 tons and inspects them every 12 months. Paul Industries reviews the refrigerant and its registration path with the owner before a replacement machine is chosen.

What happens when a chiller evaporator freezes in a Wisconsin plant?

Split tubes let water into the refrigerant circuit, so the repair goes beyond the tubes: refrigerant and oil are recovered and replaced, the circuit is dehydrated and evacuated, filter-driers and contaminated components are replaced, and the bundle is plugged or retubed. Because the system is opened and repaired, the SPS 345 registration and inspection apply before it returns to service.

When should Wisconsin chillers be overhauled?

October through April suits overhauls on most comfort chillers in Wisconsin, since cooling loads are low and outages can run longer. Process chillers are overhauled during planned plant shutdowns, and hospital and data center machines one at a time with redundancy confirmed. Paul Industries books state inspection dates and registration lead times into the overhaul plan.

How should a Wisconsin chiller be laid up for winter?

A machine that will sit idle has its evaporator and any exposed piping drained or protected with glycol, its control power left on for crankcase and oil heaters where the manufacturer calls for it, and its flow switches and freeze safeties tested. Air-cooled machines get their low-ambient controls and heaters checked. In spring Paul Industries refills, pressure checks and starts the machine under load before the first warm week.

Does Paul Industries repair process chillers at Wisconsin dairy and brewing plants?

Paul Industries repairs process chillers at Wisconsin dairy, cheese, brewing, beverage and food plants, including glycol chillers serving fermenters, brine systems and product cooling. Repairs are planned into production shutdowns where possible, and the glycol loop’s strength, inhibitors and strainers are checked at the same visit so the machine and its loop return together.

How much does a summer chiller failure cost a Wisconsin manufacturer?

The cost of a summer failure is mostly lost production and product at risk, plus emergency rental cooling, refrigerant and expedited parts, so it varies widely by plant. A frozen-tube failure discovered on the first hot week is a common and avoidable case. Paul Industries reduces that risk with autumn layup, spring startup checks, tube testing and a parts plan for critical machines.

Can a hospital chiller in Wisconsin be repaired without losing cooling to critical rooms?

Hospital chiller repairs are planned around backup capacity: remaining machines, waterside economizers or temporary chillers are checked against the load expected during the outage, critical rooms are confirmed on reduced plant, and work follows the hospital’s outage procedures. Winter repairs have the most margin. Paul Industries plans the outage with the facility team and tests the repaired machine under load before it rejoins the plant.

What records should a Wisconsin plant keep for each chiller?

Keep the SPS 345 registration and permit to operate, state inspection reports, refrigerant addition and leak rate records, leak inspection records for R-22 and R-123 machines, eddy current and tube records, any welded repair documentation under SPS 341, and the service history. Paul Industries hands back each repair with these records updated.

Which details let Paul Industries price a Wisconsin chiller repair quickly?

Useful details are the nameplate photo with model and serial, the refrigerant and how much it holds, recent alarms, a week of operating logs, the last service report, records of refrigerant added, and the state registration and permit to operate if the machine has one. Photos of the nameplate and machine room help. Paul Industries plans the diagnostic visit from that and prices the repair with parts, refrigerant and labor shown separately.

Have a chiller to repair somewhere in Wisconsin?

Send the make, model and serial number, refrigerant, alarm history and state registration if any. Call 201-450-8280 or request a quote.