Paul Industries installs process piping in Wisconsin for dairies, cheese and whey plants, breweries, paper mills, food and chemical plants, data centers and campus utility plants, from B31.3 product and chemical lines to B31.1 steam, SPS 345 ammonia piping and utility headers. Paul designs, fabricates spools off site, installs, tests and hands over the lines with the Wisconsin registrations and inspections each system needs. The company is headquartered at 256 Shore Drive, Kilmarnock, Virginia, and pipes plants from the Lake Michigan shore to the Mississippi.

Request a quote or call 201-450-8280

Headquarters 256 Shore Drive, Kilmarnock, Virginia
Power piping B31.1 with registration and inspection under SPS 341
Ammonia piping Welded steel lines inspected before installation (SPS 345.31)
Notice to inspector At least 5 business days before construction starts
Mechanical code 2021 IMC in force since September 1, 2025
Reviewed November 2026

What is process piping in a Wisconsin plant?

Process piping in a Wisconsin plant is the piping that carries product, chemicals, gases and process utilities between tanks, vessels, pumps and equipment, as distinct from the building’s plumbing, fire protection and comfort heating. ASME B31.3 is the usual code for it, and the plant’s own specification decides how it is applied. What makes Wisconsin specific is that three neighboring piping systems in the same plant come under state rules with registrations and inspections of their own: power piping under chapter SPS 341, refrigeration piping under chapter SPS 345, and fuel and chemical piping tied to regulated tanks under chapter ATCP 93.

In a cheese plant, a single expansion can touch all of them. Product and CIP lines are sanitary process piping, steam to the pasteurizer and the whey evaporator may be power piping, the ammonia lines feeding the cooling system are refrigeration piping, and the caustic and acid supply from bulk tanks connects to regulated storage. Paul Industries scopes each line against the right rule before the first spool is drawn, so inspections and registrations are scheduled with the work instead of discovered at the end. Sanitary product piping is covered in depth on sanitary process piping in Wisconsin.

Which Wisconsin rule reaches each piping system in a plant
SystemDesign codeWisconsin stepRecord at turnover
Product, chemical and process gas linesASME B31.3 by owner specificationNo state registration; tank-connected work follows ATCP 93Weld map, examination records, pressure test record
Steam above 15 psig, hot water above 250 F, thermal fluid above 250 FASME B31.1 (SPS 341.46)Registration on SBD-5204-E; inspection after material delivery and before constructionSigned SBD-5204-E, test record
Boiler external pipingASME Section I and B31.1Inspected with the boiler installationSection I data reports, test records
Ammonia and other refrigerant pipingASME B31.5, IIAR 2, ASHRAE 15 (SPS 345)Welded steel piping inspected before installation; system registered on SBD-34Registration, inspection report, test records
Fuel oil and chemical lines from regulated tanksNFPA 30 and ATCP 93Plan review for new or underground piping; credentialed or engineer-supervised underground installationPlan approval, test and leak detection records
Compressed gas and cryogenic lines, including hydrogenASME B31.3 and NFPA 55 (SPS 341.42)Installed with the vessel and supply systemTest records, NFPA 55 layout
Chilled water, heating hot water, condenser water2021 IMC hydronic rules, B31.9 or B31.1 by owner choiceCommercial building code review with the projectTest records, flushing and treatment records

What is power piping and process piping under Wisconsin law?

Power piping under Wisconsin law is a defined term in SPS 341.04: steam piping beyond the scope of ASME Section I with a maximum allowable working pressure above 15 psig, hot water piping beyond Section I at temperatures above 250 F, and thermal fluid piping above 250 F. Those systems must be built to ASME B31.1, and the rule applies to new systems and to every replacement, modification and alteration of existing ones. Process piping has no equivalent state definition, so it follows the code the owner specifies, which is ASME B31.3 in nearly every plant.

The definitional line matters because power piping carries a state process. The installer registers the system with DSPS on form SBD-5204-E before it operates, and gives the department, the City of Milwaukee where it enforces, or an inspector at least five business days’ notice before construction so the inspection can be arranged. Exempt from both steps: lines of 2 inch nominal size and smaller, replacements and new work of 50 feet or less, and underground systems outside walk-in tunnels.

Two Wisconsin rules shape how B31.1 work is built. Slip-on flanges are limited to Class 300 primary service and are installed with double fillet welds, and the power piping inspection happens after the material reaches the site and before construction starts, with the inspector signing SBD-5204-E to accept the design and installation. The system may not be insulated or placed in service until that signature is on the form. Prefabricated power piping spools are inspected where they are fabricated, by DSPS, an authorized agent, a credentialed inspector or, for out-of-state fabricators, an active National Board commissioned inspector, and the signed form or report goes to the site with them.

Ammonia and refrigeration piping under SPS 345

Ammonia and refrigeration piping in Wisconsin falls under chapter SPS 345, which adopts ASHRAE 15-2007 and IIAR 2-2008 and points refrigerant piping to ASME B31.5-2006. Closed-circuit ammonia systems may be designed, built, installed and tested to IIAR 2 with Wisconsin’s changes, together with the ASHRAE 15 sections on machinery rooms and testing. Dairies, cheese plants, breweries, meat plants and cold storage warehouses across the state run these systems.

The Wisconsin step that most affects a piping contractor is in SPS 345.31: all refrigerant steel piping that will be welded is inspected by DSPS or its authorized agent after the material is delivered to the job site and before it is installed, with at least five business days’ notice before construction. Registration on form SBD-34, due 20 business days ahead of first operation, covers Group A1 and B1 systems from 50 tons and Group B2 systems, ammonia among them, from 10 tons; a registered system is registered again before it restarts after an alteration, repair or replacement. The state then inspects within 45 business days of completion.

Paul Industries builds ammonia piping to those rules, from engine room headers to evaporator feeds, relief headers and the machinery room ventilation connections, and schedules the material inspection and registration into the project plan. The national scope is described under ammonia refrigeration, and receivers and recirculators on pressure vessel fabrication in Wisconsin.

Process piping vs plumbing under the Wisconsin codes

Plumbing in Wisconsin is governed by the Wisconsin Plumbing Code, chapters SPS 381 to 387, which covers drainage, venting, storm and clearwater systems and water supply for buildings, while process piping carries product, chemicals and utilities to equipment under the code the owner specifies. The two meet wherever a potable water line feeds a process: a CIP make-up connection, a chemical dilution panel, a boiler feed, a cooling tower fill or a hose station in a production room.

At that point the plumbing code’s cross-connection rules in SPS 382.41 take over. The water supply connection to each piece of equipment and each nonpotable piping system must be designed, installed and maintained to prevent contamination, using a method, device or assembly from the code’s table chosen by whether the hazard is high or low and whether the pressure is continuous. Paul Industries designs process tie-ins with that boundary marked on the drawings, so the backflow protection, its registration and its test access are settled before installation.

Hydronic heating and cooling piping sits under the mechanical code. Wisconsin adopted the 2021 International Mechanical Code, with the 2021 building, fuel gas and energy codes, effective September 1, 2025, and the IMC carries the hydronic piping requirements the boiler code points to. Fuel gas systems for heating appliances and engines fall under chapter SPS 340 rather than the boiler code.

Where process piping work concentrates in Wisconsin

Process piping work in Wisconsin concentrates in food and dairy, paper, metals and machinery, chemicals and, more recently, data centers. The state makes a quarter of the nation’s cheese, and every new vat line, whey dryer or membrane system brings product, CIP, steam, glycol and ammonia piping with it. Paper mills in the Fox Valley and central Wisconsin run steam, condensate, chemical and stock piping, breweries and distilleries in Milwaukee and beyond run wort, beer, CO2 and spirit lines, and data center construction, led by the Mount Pleasant campus Microsoft unveiled in September 2025, adds large chilled water and condenser water headers.

Piping materials Paul Industries installs for common Wisconsin services
ServiceUsual materialJoiningWisconsin notes
Milk, whey, beer and CIP304L or 316L sanitary tubeOrbital welds, sanitary clamps at equipmentSlope and drainability; caustic and acid CIP chemistry
Plant steam and condensateCarbon steel, Schedule 40 or 80Butt welds, socket welds at small boreB31.1 registration above 15 psig beyond the exemptions
Ammonia refrigerationCarbon steel suited to low temperatureWelded, flanged at equipmentInspection before installation; SBD-34 registration
Glycol and chilled waterCarbon steel, stainless or copper by sizeWelded, grooved or brazedFreeze protection and expansion in outdoor runs
Caustic, acid and hypochloriteCarbon steel, stainless, alloy or lined pipe by chemicalWelded or flanged with compatible gasketsContainment at tank connections under ATCP 93
Compressed air, nitrogen and CO2Carbon steel, stainless or aluminumWelded, threaded or press fittings by sizeNFPA 55 for cryogenic and bulk gas supply
Fuel oil to boilers and generatorsCarbon steelWelded, double wall where buriedUnderground work by credentialed persons or under an on-site engineer

Steam, condensate and thermal fluid piping at Wisconsin plants

Steam and condensate piping at Wisconsin plants carries the heat for pasteurizers, cheese vats, evaporators, dryers, paper machines, brew kettles and building heat, and much of it sits inside the state’s power piping rules. Thermal fluid systems are treated the same way: SPS 341.48 requires heaters using organic or synthetic heat transfer fluids to be built to the ASME code, and their piping above 250 F to be installed to B31.1. Food plants with fryers, ovens or jacketed cookers on thermal oil therefore register and inspect that piping like high-pressure steam.

Condensate return is where Wisconsin plants lose the most energy and the most pipe. Carbonic acid in returned condensate thins carbon steel lines from the inside, and water hammer from poorly drained mains breaks traps, gaskets and supports. Paul Industries lays out mains with drip legs and trap stations at the intervals the steam load needs, sizes condensate lines for flash steam, and replaces failed sections in materials and wall thickness that suit the measured corrosion rate. The boiler side of those systems, including feedwater and blowdown, is covered on boiler repair in Wisconsin.

Steam to process equipment also needs pressure control. Reducing stations, their bypasses and the relief valves downstream of them are sized as a set, and Wisconsin’s boiler code sets the formula for the downstream relief capacity on vessels fed through a reducing station. Paul Industries designs and installs the station, the relief and the vessel connection as one package, so the inspector sees a complete system.

Testing and turnover by piping system

Testing and turnover requirements differ by piping system, and a Wisconsin plant expansion often needs four or five test regimes on the same job. The table summarizes the usual approach for each system Paul Industries installs; the plant’s specification and the governing code set the final values.

Pressure testing and acceptance for common Wisconsin piping systems
SystemUsual testGoverning documentAcceptance in Wisconsin
B31.3 process linesHydrostatic at 1.5 times design pressure, temperature-corrected; pneumatic where water is unacceptableASME B31.3 and owner specificationOwner’s inspector; no state registration
Category D utility linesInitial service leak test where the owner elects itASME B31.3Owner’s inspector
Power piping and boiler external pipingHydrostatic at 1.5 times design pressureASME B31.1 and Section IInspector’s signature on SBD-5204-E before insulation and service
Ammonia refrigerationField pressure test to the levels set for the system design pressureIIAR 2, ASHRAE 15, B31.5 as adopted in SPS 345Material inspection before installation; state inspection after completion
Sanitary product and CIPHydrostatic or pneumatic leak test plus weld inspection recordsOwner specification, often ASME BPE practiceOwner and food safety program
Fuel oil and tank pipingTightness testing and leak detection checksNFPA 30 and ATCP 93DATCP or authorized agent where plan review applies

Existing piping needs a plan as well. Plants with aging steam, ammonia or chemical lines use in-service inspection under API 570 or the owner’s mechanical integrity program to find thinning, corrosion under insulation and failed supports before a leak does. Paul Industries replaces the sections an inspection flags, upgrades supports and insulation, and records the new thickness readings so the next inspection has a baseline.

Winter, freeze protection and testing on Wisconsin piping

Winter decides more Wisconsin piping details than any other site condition, because the state energy code sets winter design temperatures from minus 10 F in Milwaukee, Racine and Kenosha to minus 25 F in Douglas, Ashland and Vilas counties. Water, glycol, condensate and CIP lines on outdoor racks, in unheated truck bays or on rooftops need drainable layouts, low-point drains that stay reachable, heat tracing and insulation sized for those temperatures, and steam traps and condensate lines arranged so they cannot hold water when idle.

Testing in winter needs the same care. Hydrostatic tests on outdoor lines use heated water or a freeze-protected medium where the specification allows it, and pneumatic tests, where B31.3 permits them, need the safety distances and stepwise pressurization the code sets. Paul Industries schedules outdoor tests for the warm part of the day or encloses the test section, and drains and blows down lines as soon as each test is accepted, before any freeze risk. Heat tracing design and installation are described on the heat tracing page.

Expansion is the other cold-weather problem. A steam or hot water line installed in January and run at full temperature in July moves further than one built in mild weather, so loops, guides and anchors on Wisconsin racks are set for the full range from the design winter to operating temperature.

Gas, air and cooling utilities for Wisconsin breweries, food plants and campuses

Utility piping for Wisconsin breweries, food plants and campuses covers compressed air, CO2, nitrogen, glycol, chilled water and heating hot water, and it often grows faster than the process it serves. A brewery that adds fermenters needs more glycol capacity, more CO2 recovery and distribution and more clean compressed air at the packaging line; a cheese plant that adds a vat line needs more ice water or glycol, more air for valves and more nitrogen for packaging. Paul Industries sizes the headers for the next expansion as well as this one, so the following project ties in at a valve rather than a shutdown.

Bulk CO2 and nitrogen supplies bring NFPA 55 into the layout through the vessel and piping rules in SPS 341.42, with relief, venting and separation set on the drawings. Glycol and chilled water headers on campuses and data center sites in southeast Wisconsin are large carbon steel or stainless systems that need careful flushing, filtration and chemical treatment before they go into service, and expansion tanks and air separators sized for the full loop. Those hydronic systems sit under the 2021 International Mechanical Code as Wisconsin adopted it, and Paul Industries installs, flushes and treats them, then hands over the flushing and water quality records with the piping.

Spools, tie-ins and outages at operating Wisconsin plants

Tie-ins at operating Wisconsin plants are planned around production calendars that leave little slack: dairies receive milk every day, mills run continuously between planned outages and breweries schedule around packaging runs. Paul Industries fabricates spools off site from field measurements and 3D models, hydrotests them where the code allows before they reach the plant, and stages them so the tie-in window covers only the cut, fit, weld, examination and test.

For power piping, prefabricated spools are inspected where they are fabricated before shipment, and the signed SBD-5204-E or inspector’s report goes with them, which keeps the field inspection short. For refrigeration piping, the material inspection before installation is booked with the five business days’ notice the rule requires. Welding procedures and welder qualifications follow ASME Section IX, and the welding side is described on industrial welding services in Wisconsin.

Lines that connect to tanks and vessels are planned with them. A new bulk chemical tank brings new transfer, vent and fill piping, and a new boiler brings feedwater, blowdown and steam headers; those scopes are covered on tank fabrication in Wisconsin and boiler repair in Wisconsin.

What does process piping in Wisconsin cost?

The cost of process piping in Wisconsin is set by material, diameter, schedule, the number of welds and fittings, the examination level, insulation and heat tracing, supports and racks, access, and the number and length of shutdowns the tie-ins need. Sanitary stainless with orbital welds and borescope records costs far more per foot than carbon steel utility pipe, and work inside a running plant costs more than the same footage on a greenfield site.

Wisconsin adds registration and inspection time for power and refrigeration piping, winter enclosures and heating for outdoor work, and freeze protection on exposed lines. Paul Industries gives a budget range from comparable systems once line lists or P&IDs are available, then a firm price after a site walk. Request a quote with the drawings, line list and tie-in windows.

Who installs process piping in Wisconsin?

Paul Industries installs process piping in Wisconsin, covering product and CIP lines, chemical and process gas lines, steam and condensate, ammonia refrigeration, glycol and chilled water, compressed air and nitrogen, and fuel oil systems. The work runs from design and line sizing through spool fabrication, installation, supports, examination, testing, cleaning, insulation and heat tracing, with supply-only spools, design-build and complete installation offered.

When plants compare process piping companies for Wisconsin work, the differences that matter are whether the bid covers the state steps for power and refrigeration piping, how tie-ins are sequenced around production, what examination and test records come with the turnover, and whether the vessels, tanks and boilers at each end are part of the same contract. Paul Industries covers all of those. The national service is described on process piping, the headquarters state’s work on process piping in Virginia and a Northeast comparison on process piping in New York.

Process piping from Paul Industries for Wisconsin plants

Paul Industries, headquartered at 256 Shore Drive, Kilmarnock, Virginia, is an East Coast contractor once based in northern New Jersey, then Pennsylvania, and it designs, fabricates and installs piping for plants across Wisconsin, in all 50 states and at plants abroad. The state’s industrial picture is set out on the Wisconsin and Midwest pages. Send the P&IDs or line list, the materials, the codes the plant uses, photographs of tie-in points and the shutdown dates. Call 201-450-8280 or request a quote.

Standards referenced: ASME B31.3 Process Piping · ASME B31.1 Power Piping (SPS 341.46) · ASME B31.5 Refrigeration Piping (SPS 345) · ANSI/IIAR 2 and ASHRAE 15 · NFPA 55 Compressed Gases and Cryogenic Fluids Code · Wisconsin Administrative Code chs. SPS 341, SPS 345, SPS 382 and ATCP 93 · 2021 International Mechanical Code as adopted in SPS 361 to 366 · ASME Section IX

Frequently asked questions

Who installs process piping, Milwaukee plants and breweries included?

Paul Industries installs process piping for plants, breweries and food processors in Milwaukee, Waukesha, Racine, Kenosha and across Southeast Wisconsin, including product and CIP lines, steam and condensate, glycol, CO2 and compressed air. Power piping inside the City of Milwaukee is registered and inspected through the city where it enforces the boiler code, and spools are prefabricated to keep tie-in windows short.

Who handles process piping, Wisconsin dairies and cheese plants included?

Paul Industries handles process piping for Wisconsin dairies, cheese and whey plants, from sanitary product and CIP lines to steam, glycol and ammonia refrigeration piping. Tie-ins are planned around milk receipts and cleaning windows, with spools built off site and installed during short outages. Sanitary lines get orbital welds, slope for drainage and documented weld inspection.

Does Paul Industries pipe paper mills and plants in the Fox Valley and Green Bay?

Yes. Paul Industries pipes mills, food plants and manufacturers in Appleton, Neenah, Kaukauna, Oshkosh and Green Bay, with work covering steam and condensate, chemical, water and compressed air systems. Mill work is scheduled into planned outages, and steam lines above 15 psig are registered and inspected as power piping under SPS 341.

Who builds piping for Madison, Dane County and Janesville plants?

Paul Industries builds process and utility piping for laboratories, food plants, manufacturers and campus utility plants in Madison, Middleton, Sun Prairie, Janesville and Beloit. Work in occupied campus and lab buildings is phased to keep utilities running, with temporary connections where an outage would affect research or patient care.

What is power piping and process piping, and why does Wisconsin treat them differently?

Power piping is steam above 15 psig, hot water above 250 F or thermal fluid above 250 F beyond the boiler’s own piping, and Wisconsin requires it to meet B31.1 with registration and inspection. Process piping carries product, chemicals and utilities to equipment under the code the owner chooses, usually B31.3, without a separate state registration. The difference changes paperwork and schedule.

Process piping vs plumbing: which Wisconsin code covers a CIP water supply?

The CIP circuit is process piping, but the potable water line feeding it is plumbing up to the point of connection, and SPS 382.41 requires that connection to be protected against cross contamination with a method chosen by hazard and pressure. Paul Industries marks that boundary on the drawings and installs the backflow protection with test access.

Does a new steam line in Wisconsin need a state inspection?

A steam line above 15 psig is power piping, and unless it is 2 inch nominal size or smaller, 50 feet or less, or underground outside a walk-in tunnel, it is registered on form SBD-5204-E and inspected after the material arrives and before construction starts. Insulation and startup wait for the inspector’s signature on that form.

Does ammonia piping need DSPS inspection before it is installed?

Yes, where the steel piping will be welded. SPS 345.31 requires DSPS or its authorized agent to inspect welded refrigerant steel piping after it is delivered to the site and before installation, with at least five business days’ notice. The system is registered before operation and inspected within 45 business days of completion.

Can piping from a chemical tank to a process be changed without DATCP plan review?

ATCP 93.100 exempts the reconfiguration of aboveground product piping that runs from regulated storage tanks to a manufacturing, industrial or blending process. New tank piping, underground piping and changes to corrosion protection or spill and overfill protection still need plan review and written approval before work starts.

How do process piping companies differ on a Wisconsin bid?

Compare whether each bid includes the SPS 341 and SPS 345 registrations and inspections, spool prefabrication, tie-in sequencing, examination and test records, insulation and heat tracing, and the equipment at each end of the lines. Bids that leave those out are not comparable. Paul Industries prices them in and delivers a full turnover package.

How should outdoor piping be protected from Wisconsin winters?

Outdoor lines are laid out to drain completely, with reachable low-point drains, heat tracing and insulation sized for the county’s winter design temperature, which is minus 10 F around Milwaukee and reaches minus 25 F along Lake Superior. Steam traps and condensate lines are arranged so they hold no water when idle, and expansion is allowed for over the full temperature range.

Which piping code applies to hydrogen or nitrogen supply lines in Wisconsin?

NFPA 55 applies on top of the ASME code to compressed gas and cryogenic systems, hydrogen in gas or liquid form included, under SPS 341.42. Process gas distribution is normally built to B31.3. Fuel gas used for heating appliances or engines falls under SPS 340 instead of the boiler code.

Can spools be built off site and shipped to a Wisconsin plant?

Yes. Paul Industries fabricates spools off site from field measurements and models, examines and tests them where the code allows, and ships them ready to install. Power piping spools are inspected at the fabrication location before shipment, with the signed form or inspector’s report sent to the site, which shortens the field inspection.

What records come with a finished piping job at a Wisconsin plant?

The turnover file includes isometrics or as-built drawings, material test reports, weld maps with welder identification, welding procedure and qualification records, examination reports, pressure test records, cleaning and passivation records where relevant, and the state forms for registered power or refrigeration piping. Paul Industries assembles that file for every system it installs.

How long does a process piping project take at a Wisconsin plant?

Duration depends on footage, material, the number of tie-ins and the outage windows available. Prefabrication runs in parallel with site preparation, so the plant’s downtime is limited to the tie-ins. Registration notice periods for power and refrigeration piping are built into the schedule. Paul Industries sets dates in the proposal once drawings and windows are known.

What should a Wisconsin plant send to get process piping priced?

Send P&IDs or a line list with sizes, materials, design pressures and temperatures, the plant’s piping specification, photographs or a model of the routing and tie-in points, insulation and heat tracing needs, and the shutdown windows. Paul Industries returns a budget range, then a firm price after a site walk.

Planning new process lines at a Wisconsin plant?

Send the line list or P&IDs, materials, design conditions and tie-in windows. Call 201-450-8280 or request a quote.