Paul Industries provides boiler repair in New York for process plants, hospitals, campuses, food and beverage producers and commercial towers, following the New York State boiler law and Industrial Code Rules 4 and 14 upstate and to the Department of Buildings boiler rules in the five boroughs. Firetube, watertube, cast iron and electric boilers are diagnosed, retubed, rebuilt and returned to service by Paul Industries, which also repairs burners, flame safeguards and controls and supplies and installs replacement units. New York splits boiler oversight between Albany and New York City, so the same tube failure produces different paperwork depending on which side of the city line the boiler sits.

Request a quote or call 201-450-8280

Headquarters 256 Shore Drive, Kilmarnock, Virginia
State inspections High-pressure steam boilers: internal and external every year (NYS DOL)
NYC cycle January 1 to December 31; reports due within 14 days (DOB)
NYC defect window 90 days to correct a defect found at inspection
No. 4 oil in NYC Barred in boilers from July 1, 2027 (NYC LL32 of 2023)
Reviewed November 2026

Which agency oversees a boiler in New York State and in New York City?

New York boiler oversight sits with two agencies: the Boiler Safety Bureau of the New York State Department of Labor, which enforces Labor Law Section 204 and Industrial Code Rules 4 and 14 across the state, and the New York City Department of Buildings, which runs its own inspection program inside the five boroughs. The state program reaches every regulated boiler in Buffalo, Rochester, Syracuse, Albany, the Hudson Valley and Long Island. The state law lets a city that performs its own inspections take over that role, and New York City does, through the NYC boiler code provisions in its Construction Codes, the inspection rules in Title 1 of the Rules of the City of New York, and filings in DOB NOW: Safety.

Rule 4 covers low-pressure boilers, and its subparts set requirements for installation, repair and replacement of low-pressure heating boilers, flame safeguards on gas and oil burners, and hydrostatic tests. Rule 4 is a separate document from Rule 14, the NYS high pressure boiler code, which governs construction, installation, inspection and maintenance of high-pressure boilers and the construction of unfired pressure vessels. Together, Rules 4 and 14 are what most engineers mean when they say the NYS boiler code. The national picture of tube failures, burner faults and retubing is covered on the boiler repair service page; this page deals with how New York’s rules shape each repair.

New York State and New York City boiler programs side by side
ItemNew York State (outside NYC)New York City (five boroughs)
AuthorityLabor Law 204; Industrial Code Rules 4 and 14NYC Construction Codes; 1 RCNY 103-01 and 103-05
AgencyNYS Department of Labor, Boiler Safety BureauDepartment of Buildings, Boiler Unit
Who inspectsDepartment inspectors, or insurance company inspectors commissioned by the departmentLow pressure: DOB license holders or an authorized insurer; high pressure: an authorized insurance company
Report filingNational Board forms or online, within 21 days, $100 per boilerDOB NOW: Safety, within 14 days of each inspection
Proof of complianceCertificate of inspection: 12 months high pressure, 24 months low pressureAccepted annual report each cycle; First Test Inspection sign-off for a new boiler
Operator rulesNo statewide boiler operator licenseHigh-pressure steam boilers run under an operating engineer holding a DOB license, with listed exceptions

How often do you need a boiler inspection in NY?

New York State boiler inspection requirements set intervals by pressure class and medium: high-pressure steam boilers get internal and external inspections every year, high-pressure hot water boilers get an annual external and an internal every three years, low-pressure steam boilers an internal every three years and an external every two, and low-pressure hot water boilers an internal every five years and an external every two. A high-pressure hot water boiler with manholes and handholes moves to an annual internal, and the external on high-pressure units falls about six months after the internal. Labor Law 204 sets the outer limit at two years for most boilers and one year for high-pressure power, antique and miniature boilers.

The NYS boiler inspection is made either by a department inspector or by an inspector employed by the insurance company that covers the boiler and commissioned by the department. The insurer files the report on National Board forms or through the online system within 21 days, and the certificate of inspection that follows runs 12 months for high-pressure boilers and 24 months for low-pressure ones. Exemptions in the statute include low-pressure boilers under 100,000 Btu per hour and heating boilers in dwellings of fewer than six families, so a plant’s small unit heaters and a large process boiler can sit under very different schedules in the same building.

NYS boiler inspection requirements by boiler type (12 NYCRR 14-1.2)
Boiler typeInternal inspectionExternal inspectionWhat a repair outage should line up with
High-pressure steamEvery yearEvery year, about six months after the internalTube, refractory and drum work timed to the annual internal so the inspector sees the opened boiler once
High-pressure hot waterEvery 3 years; yearly if fitted with manholes and handholesEvery yearCirculating pump and expansion tank work during the external window
Low-pressure steamEvery 3 yearsEvery 2 yearsLow-water cutoff, gauge glass and return line repairs before the heating season
Low-pressure hot waterEvery 5 yearsEvery 2 yearsSection leaks, relief valves and burner controls ahead of the external

NYC boiler inspection requirements, deadlines and DOB NOW filings

NYC boiler inspection requirements call for an annual inspection of every low-pressure boiler in residential buildings of six or more families, in all commercial and mixed-use buildings and in single room occupancy dwellings, and two inspections a cycle, internal and external, on every high-pressure boiler. The NYC annual boiler inspection cycle, the frame for every NYC DOB boiler inspection, runs from January 1 to December 31. Low-pressure inspections are made by DOB license holders or an authorized insurer, and high-pressure inspections by an authorized insurance company, with DOB notified at least ten days before a high-pressure internal.

The NYC boiler inspection deadline that catches owners out is the filing window: each report goes into DOB NOW: Safety within 14 days of the inspection, a report filed after that but by January 14 of the next year is late, and one filed after January 14 is treated as expired. Defects found at inspection are corrected within 90 days, and an affirmation of correction filed more than 104 days after the initial inspection is rejected; up to two 45-day extensions can be requested before the correction deadline. A dangerous condition that forces an immediate shutdown is emailed to the DOB Boiler Unit within 24 hours. NYC boiler inspection records for each device live in DOB NOW, which is why Paul Industries hands owners repair documentation in a form the inspector can attach to the affirmation.

From an inspection finding to a repair scope

A boiler inspection finding becomes a repair scope when the inspector’s report names a condition, the owner decides how to correct it, and the correction is documented in time for the agency’s deadline. Paul Industries reads the report, opens and inspects the unit, sets out the repair, the parts and the outage, and returns it to service with the records the next inspection will ask for. In New York City, that sequence has to fit inside the 90-day correction window; upstate, an unsafe condition can lead the commissioner to order the boiler out of use until it is remedied.

Keeping heat or process steam available while a unit is down is part of the same plan. Where a plant has a second boiler, Paul Industries confirms it can carry the load before the first is isolated, checks that unit’s certificate date so both units are never out of compliance at once, and stages the repair so the standby unit is fired and proven first. Where a site has a single boiler, the plan sets out a temporary steam or hot water connection, the load the building can shed, and the order in which the repaired unit is brought back, tested and handed to the operator. Repairs scheduled for late spring or early autumn avoid the coldest weeks for heating plants; process plants usually fold the work into an existing production shutdown so the outage costs no extra downtime.

Common New York inspection findings and how each is corrected
Inspection findingTypical repairRecord that closes it out
Leaking or thinned firetubesTube replacement or full retube; tube sheet ligament checksRepair report on National Board form R-1 where welding is involved; hydrostatic test record
Low-water cutoff fails to tripRebuild or replace the cutoff; clean float chamber and pipingFunctional test log witnessed or reviewed by the inspector
Safety valve leaking, gagged or out of dateReplace with a valve of matching set pressure and capacityValve data sheet and nameplate photo
Flame safeguard faults or bypassed interlocksReplace programmer, scanner or limit; restore interlocksCombustion and safety checkout sheet
Refractory or rear door damageReline door, target wall or burner throatCure log and photo record
Cracked cast iron sectionSection replacement or boiler replacement, whichever the condition supportsHydrostatic test record; DOB First Test Inspection if the boiler is replaced

Welded repairs and alterations under the New York boiler code

The New York boiler code requires a welded repair to a boiler to be made under a National Board R certificate or a New York State Repair Certificate of Authorization, or an ASME Certificate of Authorization, with a documented quality control program and welding procedures qualified to ASME Section IX. Alterations, which change a boiler’s design, pressure or temperature rating, follow the National Board Inspection Code, and the design change itself is approved by the holder of the matching ASME Code symbol stamp and verified by that holder’s authorized inspector. Paul Industries plans each welded repair around those requirements, so the inspector sees qualified procedures, the welder record and the R-1 report together.

Hydrostatic testing after a repair follows Subpart 4-15 for low-pressure boilers and the inspector’s direction for high-pressure units. Non-welded work, such as replacing a gasketed handhole cover, a gauge glass or a burner component, still leaves a record, because the next inspector will ask what changed since the last report. Related hydrostatic testing and industrial welding in New York pages describe the test and weld side in more depth.

Who runs the boiler: the NYC boiler license and upstate operators

A New York City high-pressure steam boiler must be operated under the direct and continuing supervision of a high-pressure boiler operating engineer holding a Department of Buildings license, under Administrative Code Section 28-413.1, unless every condition in the code’s listed exceptions is met. The NYC boiler license therefore shapes a repair outage: the license holder isolates the unit, releases it for work and takes it back for start-up. Outside the city, New York has no statewide boiler operator licensing law, so the operator requirement on an upstate plant comes from the owner’s insurer, corporate policy or a municipal rule.

Hot work inside the five boroughs adds Fire Department requirements. Torch work with oxygen and a flammable gas is performed by a holder of an FDNY Certificate of Fitness G-60, a fire guard holding an F-60 watches where the code calls for one, and the work runs under the applicable hot work permit. Paul Industries schedules the work around those requirements and the building’s license holder, which keeps the outage plan intact from lockout to start-up.

Commercial boiler repair, NYC buildings: fuel, DEP filings and emissions limits

Commercial boiler repair in NYC is shaped by three Department of Environmental Protection and building energy rules: boiler registration or a certificate of operation by size, the phase-out of No. 4 fuel oil, and Local Law 97 (LL97) emissions limits. DEP registers boilers of 350,000 Btu per hour up to 2.8 million as Registration I, 2.8 million to 4.2 million as Registration II with an original inspection and combustion test data, and units of 4.2 million Btu per hour and above under a work permit and certificate of operation filed by a professional engineer or registered architect. Registrations and certificates run three years.

NYC’s LL32 of 2023 stopped new or renewed permits for No. 4 oil on June 30, 2024 and bars any boiler from burning it from July 1, 2027, with city property and public schools cut off from July 1, 2025. A burner repair on a dual-fuel boiler that still lists No. 4 is therefore a good moment to plan the conversion. Buildings over 25,000 square feet also answer to LL97 emissions limits that tightened from 2024 and tighten again in 2030, and buildings over 50,000 square feet complete Local Law 87 (LL87) energy audits and retro-commissioning every ten years; both reward a boiler that burns cleanly and holds its combustion settings. Boiler service NYC buildings schedule between repairs, including combustion tuning, is where those savings are held.

NYC DEP boiler filings by heat input
Heat input per boilerDEP filingTermWhat a repair or replacement may touch
350,000 to under 2.8 million Btu/hrRegistration I3 yearsMake, model, input and fuel on file; replacement units filed again
2.8 to under 4.2 million Btu/hrRegistration IIInitial 6 months, final 3 yearsOriginal inspection with performance and combustion test printouts
4.2 million Btu/hr and aboveWork permit, then certificate of operationPermit 1 year; certificate 3 yearsDrawings, draft calculations for new boilers or chimneys, original inspection

Industrial and commercial boiler repair, New York State plants

Commercial boiler repair, New York State style, outside the city turns on the Department of Labor certificate, the insurer’s inspection and, for larger plants, the NYSDEC air permit. Under 6 NYCRR 201-3.2, combustion units with a maximum heat input under 10 million Btu per hour burning liquid or gaseous fuel are exempt from air permitting at facilities without a Title V permit, though they are still listed in a Title V application, and exempt units lose that status if together they push a facility past a major source threshold. A burner retrofit that changes fuel or firing rate on a larger boiler is checked against the facility’s air permit before work starts.

Boiler rooms built or altered outside New York City now follow the 2025 Uniform Code, including the 2025 Mechanical Code of New York State, which took effect on December 31, 2025. The New York State boiler regulations in Rules 4 and 14 sit alongside that code: the Uniform Code governs the room, venting and clearances, and the Labor Department governs the pressure vessel that is the boiler. Steam plants also benefit from attention beyond the boiler itself, so Paul Industries pairs repairs with steam trap surveys and boiler water treatment where condensate return and scale are behind the failure.

Upstate plants, downstate buildings: where New York boilers work hardest

New York’s boilers split broadly into downstate building heat and upstate process steam, and the repair emphasis follows. In Manhattan, many buildings take heat from Con Edison’s district steam system, which serves more than 1,500 customers, while hospitals, universities and towers elsewhere in the five boroughs fire their own boilers. Upstate, steam and hot water serve process loads: biologics in Rensselaer, where Regeneron has made large-scale biologics since 2003; dairy in the Mohawk Valley, where Chobani broke ground on a $1.2 billion plant in Rome in April 2025; and the semiconductor build-out in Clay, where Micron broke ground in January 2026.

Boiler repair emphasis across New York
RegionTypical boilersRepair emphasis
Manhattan, Brooklyn, Queens, the Bronx, Staten IslandLow-pressure heating boilers, high-pressure plants at hospitals and campusesDOB defect corrections inside 90 days, burner and fuel conversions, coordination with the building’s license holder
Long Island (Nassau and Suffolk)Hospital, laboratory and campus steam and hot waterHumidification and sterilizer steam, condensate return, controls
Westchester and the Hudson ValleyPharmaceutical and institutional boilersClean utility support, redundancy during outages
Capital Region and Mohawk ValleyBiologics and dairy process steamRetubing on schedule, low-water and flame safeguard reliability
Central NY, Finger Lakes and RochesterFood, optics, semiconductor and university plantsFeedwater and deaerator repairs, scale and corrosion control
Buffalo-Niagara, the Southern Tier and the North CountryFood processing, chemical and paper steamWinter reliability, refractory, watertube and economizer work

Boiler replacement in NYC and upstate: what a new unit sets off

Boiler replacement NYC owners plan for starts with a DOB First Test Inspection before the new boiler is used, plus the DEP registration or certificate that matches its heat input; a boiler that passes the First Test Inspection needs no annual report for that inspection year. Upstate, a new unit is built to the ASME Code and shop-inspected by an inspector holding a National Board commission, its Manufacturer’s Data Report is filed with the Department of Labor, and high-pressure boilers are registered with the National Board. The state assigns a number that the owner attaches to the unit.

Paul Industries supplies and installs replacement boilers as well as repairing existing ones, and it offers supply-only, design-build and complete installation routes. A replacement is worth pricing against a repair when the boiler needs a second retube, when cast iron sections are cracking in more than one place, when the burner runs on a fuel that is being phased out, or when the unit is oversized for a building that has cut its load. Piping changes that come with a new boiler are covered on the process piping in New York page, and the cooling side of a central plant on the chiller repair in New York page.

What drives the price of boiler repair in New York?

The price of boiler repair in New York is driven by the boiler’s type and size, the extent of the damage found once it is opened up, whether the repair is welded, the outage window, and the inspection and filing steps that close it out. The state’s own inspection fees are fixed: $200 for an internal, $75 for an external, and no more than $275 for any one boiler in a year, plus a $100 filing fee per boiler on insurer reports. In New York City, the cost of a missed filing is predictable too, at $50 a month up to $600 for a late report and $1,000 for a failure to file.

The repair itself is priced from the scope: tubes or sections, refractory, burner parts, controls, testing and the hours inside an operating boiler room. Paul Industries gives a budget range from the inspection report and boiler data, then a firm price once the unit has been opened and the scope is fixed.

Who repairs boilers in New York?

Paul Industries repairs boilers in New York at factories, medical centers, colleges, dairies and office and residential towers, in the five boroughs and across the state. Paul Industries is headquartered at 256 Shore Drive, Kilmarnock, Virginia; formerly based in northern New Jersey, then Pennsylvania, it is an East Coast contractor that accepts New York work statewide, takes projects in every one of the 50 states, and handles international plant work as well. The New York page sets out the full range of systems Paul Industries builds and maintains in the state, including pressure vessel fabrication in New York and tank fabrication in New York.

The same code-repair work runs in the headquarters state through boiler repair in Virginia, and in neighboring states through boiler repair in New Jersey and boiler repair in Pennsylvania. For boiler repair, New York owners deal with Paul Industries under one contract for the diagnosis, the repair, the testing and the records.

Paul Industries boiler work for New York owners

Paul Industries diagnoses, repairs, retubes, rebuilds and replaces industrial and commercial boilers in New York, repairs burners, flame safeguards, low-water cutoffs and controls, and returns each boiler to service with the reports its inspector, DOB or the Department of Labor will review. Send the boiler data plate, the latest inspection report and the fault history, and request a quote for the repair.

Standards referenced: New York Labor Law Section 204 · 12 NYCRR Part 4 (Industrial Code Rule 4, Low Pressure Boilers) · 12 NYCRR Part 14 (Industrial Code Rule 14, High Pressure Boilers; Construction of Unfired Pressure Vessels) · National Board Inspection Code (NBIC) · ASME Boiler and Pressure Vessel Code Sections I, IV and IX · NYC Administrative Code Article 28-413 · 1 RCNY 103-01 and 103-05 · NYC Local Law 32 of 2023 · NYC LL97 and LL87 · 6 NYCRR Subpart 201-3 · 2025 Mechanical Code of New York State · New York Labor Law Section 220

Frequently asked questions

Who handles boiler repair in Manhattan, Brooklyn and Queens?

Paul Industries handles boiler repair Manhattan towers and hospitals call for, boiler repair Brooklyn, NY owners schedule, and boiler repair Queens, NY buildings need, along with the Bronx and Staten Island. Work in the five boroughs follows the DOB cycle, so a defect from the annual inspection is corrected and affirmed within 90 days. Send the inspection report and DOB device number, and Paul Industries scopes the repair.

Does Paul Industries take boiler repair, Long Island hospitals and plants included?

Yes. Paul Industries takes boiler repair Long Island hospitals, laboratories and plants need, including boiler repair Suffolk County and boiler repair Nassau County facilities, along with boiler replacement Long Island owners plan when a unit reaches the end of its life. Long Island boilers sit under the state program, so the certificate comes from the Department of Labor or the insurer’s commissioned inspector.

Who repairs boilers for plants in Buffalo, Rochester and Syracuse?

Paul Industries provides boiler repair Buffalo, NY food and chemical plants rely on, boiler repair Rochester, NY manufacturers and campuses schedule, and boiler repair Syracuse, NY facilities need as Central New York grows around the Clay semiconductor site. Upstate process boilers often run year round, so retubes and refractory work are planned around the annual internal inspection.

Who provides boiler repair in Albany, the Capital Region and Westchester?

Paul Industries provides boiler repair Albany, NY plants and state campuses schedule, boiler work in Rensselaer, Schenectady and Troy, and boiler repair Westchester, NY hospitals and pharmaceutical sites need, along with the rest of the Hudson Valley. Each repair is planned against the boiler’s certificate dates so the inspection and the outage fall together.

Can Paul Industries repair a boiler in Utica, Rome or elsewhere in the Mohawk Valley?

Yes. Paul Industries provides boiler repair Utica, NY plants and institutions need, and works across the Mohawk Valley, where dairy processing is expanding around Rome. Food plant boilers supply cleaning and process steam, so Paul Industries pairs repairs with feedwater, condensate and steam trap checks that keep the same failure from returning.

Are boiler inspections required in NYC for every commercial building?

Annual inspections are required for low-pressure boilers in all commercial and mixed-use buildings regardless of capacity, in residential buildings of six or more families and in single room occupancy dwellings. High-pressure boilers need an internal and an external inspection each cycle. Registered boilers in residential buildings of five or fewer families are exempt, as is a single boiler heating one apartment.

What happens after an NYC boiler inspection violation is issued?

An NYC boiler inspection violation is resolved by correcting the defect and filing an affirmation of correction in DOB NOW: Safety. Defects are corrected within 90 days of the initial inspection, and an affirmation filed more than 104 days after it is rejected. A late affirmation draws a $1,000 penalty plus $50 a month up to $600. Paul Industries makes the correction and supplies the records the filing needs.

What is the NYC boiler inspection cost once filing penalties are counted?

The NYC boiler inspection cost has two parts: the inspection itself, priced by the authorized insurer or DOB license holder by boiler count and type, and any penalty for a late or missing report. Late filing costs $50 a month per boiler up to $600, and failure to file costs $1,000 per boiler, for each inspection type on high-pressure units. Filing within 14 days avoids both.

Who inspects boilers in New York State outside the city?

Boilers outside New York City are inspected by Department of Labor inspectors or by inspectors employed by the boiler’s insurance company and commissioned by the department. Insurer reports are filed within 21 days on National Board forms, and the department accepts them in place of its own inspection. Uninsured boilers receive their certificate of inspection from the department.

Who is the New York State boiler inspector for a plant in Rochester or Syracuse?

The New York State boiler inspector for a plant is either a department inspector from the Boiler Safety Bureau or the commissioned inspector of the plant’s boiler insurer. Boiler inspection Rochester, NY plants receive follows the same state schedule as everywhere outside the city. Paul Industries times repairs to that inspector’s visit, so the opened boiler is examined once.

Where does the NYS Boiler Safety Bureau fit into a repair?

The NYS Boiler Safety Bureau, part of the Department of Labor’s Division of Safety and Health, administers the state boiler program, commissions inspectors, receives inspection reports and can order an unsafe boiler out of use. A welded repair follows the state’s repair rules and the National Board Inspection Code, and its report stays with the boiler’s inspection history.

Does NYC require a license holder on site during a high-pressure boiler repair outage?

The NYC boiler license rule requires a high-pressure steam boiler to operate under the direct and continuing supervision of a high-pressure boiler operating engineer holding a DOB license, unless every listed exception applies. During a repair, the license holder isolates the boiler and takes it back for start-up. Paul Industries plans the outage around that person’s shifts.

Do New York State boiler regulations require an operator license upstate?

New York State has no statewide boiler operator licensing law. The New York State boiler regulations govern construction, installation, inspection and repair of the boiler itself. Operator requirements upstate come from insurers, corporate standards and some municipal rules, so plants still keep trained operators on high-pressure steam. Paul Industries trains the plant’s operators on any repaired controls at start-up.

Does a burner repair in New York need a new air permit?

A like-for-like burner repair usually leaves the permit unchanged. Outside the city, units under 10 million Btu per hour on gas or liquid fuel are exempt from NYSDEC permitting at non-Title V facilities. In New York City, a fuel change or replacement burner updates the DEP registration or certificate. Paul Industries checks the permit before changing fuel or firing rate.

When must NYC buildings stop burning No. 4 oil in their boilers?

Under the city’s LL32 of 2023, no boiler in New York City may burn No. 4 fuel oil on or after July 1, 2027, and boilers in city property and public schools stopped on July 1, 2025. DEP stopped issuing or renewing No. 4 permits and registrations on June 30, 2024. Paul Industries converts burners and fuel trains to gas or No. 2 oil.

Is boiler work at a New York school district or municipal building prevailing wage work?

Boiler work on public work contracts is covered by New York Labor Law Section 220. The Bureau of Public Work at the Department of Labor enforces it on contracts let by the state and its political subdivisions, and the New York City Comptroller enforces it on city contracts. Paul Industries prices public boiler work on the applicable wage schedule in the bid documents.

What is the difference between NYC boiler maintenance and a code repair?

NYC boiler maintenance covers combustion tuning, cleaning, low-water cutoff blowdown and control checks that keep the boiler inside its permit and passing its annual inspection. A code repair corrects a defect an inspector found, such as a leaking tube or failed safety device, and is affirmed in DOB NOW. Paul Industries provides both under one service plan.

Which details let Paul Industries price boiler repair in New York?

Paul Industries prices boiler repair from the boiler’s data plate photo, the latest inspection report or DOB violation, the fuel and burner model, recent alarms and water treatment logs, and the outage the building can accept. With those, Paul Industries gives a budget range, then a firm price once the boiler has been opened and inspected.

Have a New York boiler that failed an inspection or keeps tripping?

Send the boiler data plate, the inspection report or DOB violation, and a list of recent trips and alarms. Call 201-450-8280 or request a quote.