Paul Industries provides chiller repair in Illinois for manufacturing plants, hospitals, universities, office towers and data centers, diagnosing and repairing centrifugal, screw, scroll and absorption machines from Chicago and the collar counties to Rockford, Peoria, Decatur, Springfield and the Metro East. Illinois chillers face two seasons that each break them differently: humid summers that push condensing pressure up, and long freezing winters that split tubes in any evaporator or tower left full of water. Paul Industries fixes the fault in front of it, rebuilds compressors, retrofits controls and refrigerants, and furnishes and sets new machines when repair stops paying back.

Request a quote or call 201-450-8280

Headquarters 256 Shore Drive, Kilmarnock, Virginia
Summer design 92 F dry bulb, 75 F wet bulb at O'Hare (0.4%)
Winter design -6 F at O'Hare (99.6%)
Leak repair rule HFC chillers of 15 lb or more, from January 1, 2026 (EPA)
Industrial power 8.83 cents/kWh in Illinois, 8.13 US average (EIA, 2024)
Reviewed November 2026

What does chiller repair in Illinois cover?

Chiller repair in Illinois covers fault diagnosis, refrigerant leak location and repair, compressor, bearing and motor work, starter and control repair, tube cleaning and eddy current testing, freeze damage repair, and the leak records the EPA now requires. The machines involved range from 2,000-ton centrifugal chillers in Loop high-rises to packaged process chillers on plastics and food lines in the western suburbs, and the same visit often reaches the cooling tower, pumps and piping that decide how well the chiller runs.

The national list of faults and repair methods sits on the chiller repair page. This page stays with what is particular to Illinois: a climate that swings from a 92 degree design afternoon to a 6 below zero design night, Chicago’s benchmarking and energy code rules, power prices set partly by the PJM capacity market, and a building stock that runs from 1920s steam-heated towers to new hyperscale data halls.

How the Illinois climate wears on a chiller

The Illinois climate wears on a chiller from both ends of the thermometer, because O’Hare’s design data put the 0.4 percent summer condition at 92 degrees Fahrenheit dry bulb with a 75 degree coincident wet bulb, and the 99.6 percent winter condition at 6 degrees below zero. Summer stress shows up as high head pressure and tower approach problems; winter stress shows up as split tubes, cracked pump casings and frozen tower basins.

Summer humidity matters more than the dry bulb figure suggests. The same O’Hare record counts about 1,079 hours a year with a wet bulb above 67 degrees and about 303 hours above 73 degrees, and those are the hours when a cooling tower struggles to deliver design condenser water. A water-cooled chiller with fouled condenser tubes, a tower fan out of service or a stuck bypass valve runs fine in May and trips on high pressure in July.

Winter is the other half. O’Hare’s 1981 to 2010 normals record a freezing low on about 122 days a year, and the January normal low for 1991 to 2020 is 18.8 degrees. Chillers that keep running through winter for data halls, hospitals and process loads depend on glycol, heat tracing, basin heaters and correct sequencing; chillers that are laid up depend on a drain-down that someone actually completed. Either way, a single missed step turns into a repair in spring.

Seasonal chiller faults in Illinois and how each is repaired
SeasonTypical faultRoot causeRepair
July and AugustHigh head pressure trips, surge on centrifugal machinesHumid afternoons, fouled condenser tubes, weak tower performanceTube cleaning, tower fan and fill repair, condenser water reset review
Late autumnLow suction pressure and freeze tripsLow load, low flow, glycol diluted by summer top-upsFlow verification, glycol strength correction, control setpoint changes
December to FebruarySplit evaporator or condenser tubesWater left in an idle bundle or a coil exposed to outdoor airTube plugging or retubing, dehydration of the refrigerant circuit, oil change
December to FebruaryTower basin and riser freeze-upHeaters, bypass or drain procedures not followedBasin heater and valve repair, heat tracing, revised cold-weather procedure
March and AprilStartup failures after layupMoisture in refrigerant, seized valves, failed sensorsLeak and moisture checks, valve service, sensor calibration before first load

Freeze damage: the Illinois repair most owners see once

Freeze damage is the chiller repair Illinois owners tend to meet once and then design out, because water expands as it freezes and splits copper tubes from the inside. When an evaporator tube splits on a running machine, water enters the refrigerant side; on a low-pressure centrifugal chiller the whole charge, the oil and the motor windings can be contaminated before the alarm is read.

Paul Industries handles freeze damage in a fixed order. The machine is isolated and the water side drained, the refrigerant is recovered and tested for moisture and acid, and the bundle is pressure tested to locate every failed tube. Split tubes are plugged when the count stays within the manufacturer’s allowance, or the bundle is retubed when it does not. The refrigerant circuit is then evacuated to a deep vacuum, dried, recharged with clean or reclaimed refrigerant meeting AHRI 700 purity, and the oil is replaced. Motor windings on hermetic machines are tested before the first start.

The lasting fix is upstream. A freeze repair should end with the cause corrected: a glycol loop raised to the right strength for the lowest outdoor temperature, a low-flow alarm wired to stop the machine, an outdoor coil drained or protected, or a written drain-down procedure for an idle plant. Paul Industries leaves that procedure with the operator so the next winter starts with it in hand.

Which Illinois plants need industrial chiller repair most?

Industrial chiller repair is a constant need at Illinois plants whose product depends on process cooling: plastics molders and extruders in the northwest suburbs, food and beverage plants across Chicago and the Fox Valley, agri-processing in Decatur and Peoria, pharmaceutical and biologics plants on the North Shore, and chemical and refining sites in Joliet and the Metro East. In each case a chiller fault can stop a line, spoil a batch or force a plant into a slower recipe.

Process machines differ from comfort chillers in three ways that change how a repair is done. They often run on glycol below freezing, so glycol chiller repair includes checking freeze point, inhibitor level and pump performance along with the refrigeration circuit. They serve one line, so the repair window is set by production rather than by weather. And many are packaged air-cooled units sitting outdoors or on roofs, so air cooled chiller repair in Illinois often starts with coil cleaning, fan motor replacement and winter controls such as head pressure control and low-ambient kits.

Industrial water chiller repair on process lines

Industrial water chiller repair on a molding or extrusion line is usually a short, focused job: a failed compressor contactor, a refrigerant leak at a vibration-worn tube, a clogged strainer starving the evaporator, or a plugged brazed plate heat exchanger. Paul Industries carries the diagnosis through to the water side, because a water chiller repair that replaces a compressor without clearing the debris that starved it will be repeated within the season. For process machines serving a single line, the process piping in Illinois around the chiller is often part of the same fix.

Commercial chiller repair in Chicago towers and campuses

Commercial chiller repair in Chicago office towers, university campuses and hospitals is dominated by large water-cooled centrifugal and screw machines, many of them in basement or mid-building mechanical rooms. Water cooled chiller repair there tends to be scheduled for spring and autumn, when the building can run on reduced capacity, with temporary cooling brought in only when a repair will outlast the shoulder season. Hospital plants add another constraint: operating rooms, pharmacies and sterile processing keep tight temperature and humidity limits, so the remaining machines and air handlers are checked before any chiller is isolated.

Chiller types found in Illinois buildings and the repairs each needs most
Machine typeWhere it is foundRepairs most often needed
Water-cooled centrifugalLoop high-rises, hospitals, university central plants, older data hallsBearing and seal work, vane actuators, purge repair, tube cleaning, eddy current testing
Water-cooled screwMid-size offices, process plants, suburban campusesRotor and bearing wear, oil separator and filter service, slide valve repair
Air-cooled screw and scrollRoofs and pads at plants, schools and data centersCoil cleaning and repair, fan motors, low-ambient controls, compressor replacement
Glycol process chillersFood, beverage, plastics and pharmaceutical linesFreeze point correction, pump repair, evaporator cleaning, leak repair
Steam absorption chillersCampuses and hospitals with central steamCrystallization recovery, vacuum leak repair, solution analysis, tube repair

Absorption chiller repair still matters on Illinois campuses that make steam in a central boiler plant, where a steam-fired machine uses heat that is already on site. Those machines need vacuum tightness and solution chemistry kept in range, and a crystallization event after a power loss is repaired by careful heating and dilution rather than by force. The steam side of the same plant is covered on boiler repair in Illinois.

Refrigerant leak rules behind Illinois chiller refrigeration repair

Federal refrigerant rules shape chiller refrigeration repair in Illinois more than any state rule, because the leak repair provisions of the EPA’s Emissions Reduction and Reclamation rule, in force since January 1, 2026, reach every chiller holding 15 pounds or more of an HFC refrigerant. Owners must calculate the leak rate each time refrigerant is added, and comfort-cooling chillers exceeding a 10 percent annual leak rate must be repaired within 30 days, with initial and follow-up verification tests recorded.

Industrial process refrigeration carries a 30 percent threshold and commercial refrigeration 20 percent, and a repair that needs an industrial process shutdown gets 120 days. Older machines sit under the HCFC rules instead: R-22 has not been produced or imported since January 1, 2020, and R-123, the refrigerant in many low-pressure centrifugal chillers in Chicago towers, reaches its full phaseout in 2030, after which reclaimed supply carries the existing fleet. New comfort-cooling chillers manufactured or installed from January 1, 2025 must use a refrigerant with a global warming potential below 700, so any replacement chiller arrives with a different refrigerant from the machine it replaces.

Paul Industries records the leak rate calculation, the leak location, the repair and both verification tests on the same service report, so the owner’s file shows one complete event rather than a refrigerant invoice with no explanation.

Chicago benchmarking, energy code and the chiller plant

Chicago’s Energy Benchmarking Ordinance ties chiller condition to a public number, because commercial, institutional and residential buildings larger than 50,000 square feet must report their energy use through ENERGY STAR Portfolio Manager by June 1 each year and verify the data every three years. A chiller that has drifted from its rated efficiency shows up in that report as higher electricity use per square foot, and in many towers the chiller plant is one of the largest single electric loads in the building.

The energy code matters when a repair turns into a replacement. Chicago enforces its own 2022 Chicago Energy Transformation Code, based on the 2021 IECC, for permits started on or after November 1, 2022, while the rest of Illinois follows the Illinois Energy Conservation Code, which moved to the 2024 IECC as amended on November 30, 2025 for privately funded commercial buildings. Either code sets minimum efficiencies for a new chiller and controls requirements for the plant, and Paul Industries selects replacement machines and controls to meet the edition in force where the building sits.

Repair or replace an Illinois chiller?

An Illinois chiller earns its repair when the compressor fault is confined to a component, the tubes test sound, the refrigerant has a supply path and the measured efficiency is close to its rating; it points toward replacement when the machine holds R-22 or R-123 with no plan, has a record of leak rate exceedances, needs a second retube, or has drifted far from its rated kilowatts per ton. Many owners asking how much to replace a chiller are really comparing a known repair against a replacement that also brings rigging, electrical and piping work.

Repair or replacement signals for a chiller in an Illinois building
QuestionAnswer that favors repairAnswer that favors replacement
What refrigerant is in it?R-134a, R-513A, R-1233zd or another current refrigerantR-22, or R-123 with no reclaimed supply plan past 2030
Has it frozen before?One freeze event, cause corrected, tubes tested soundRepeated freeze events or plugging near the allowance
What does eddy current testing show?Scattered pitting with good remaining wallWidespread wall loss in the condenser or evaporator
How is the leak record?One leak found, repaired and verifiedRepeated exceedances under the 2026 EPA rule
How does efficiency compare?Measured kW per ton close to the original ratingA large gap to a new machine over many run hours
Is the size still right?Load close to the original designBuilding or process load has grown or shrunk

Electricity price sets the payback. Illinois industrial customers paid an average of 8.83 cents per kilowatt-hour in 2024 against a national 8.13, and commercial customers paid 11.81 cents (EIA). As an example, a 600-ton chiller running 2,000 equivalent full-load hours a year that improves from 0.70 to 0.55 kilowatts per ton saves about 180,000 kilowatt-hours, worth roughly $15,900 a year at the industrial average or $21,300 at the commercial average. Northern Illinois buildings on ComEd also carry PJM capacity costs, and PJM’s auction for the 2027/2028 delivery year cleared at its $333.44 per megawatt-day cap, which raises the value of every kilowatt a new machine takes off the summer peak. Paul Industries runs the same calculation on the owner’s trend data and tariff before recommending either path.

Tube care, eddy current testing and chiller condenser repair

Tube care is the heat exchanger work that most often restores an Illinois chiller’s capacity: open cooling tower water carries scale, silt and biological growth into the condenser, and the warm, humid weeks of July and August accelerate it. Chiller condenser repair ranges from brushing and chemical descaling to plugging failed tubes and retubing a bundle, with eddy current testing deciding which applies.

Eddy current testing passes a probe through each tube and reads wall loss, pitting and cracks from the inside, and the results are kept so the next test shows the trend. On machines with a history of freezing, the test also finds tubes that bulged but did not split. Recurring fouling points back to the tower and its treatment, so a condenser job often continues into cooling tower repair.

Chiller maintenance requirements for Illinois plants and buildings

Chiller maintenance requirements for an Illinois facility come from the manufacturer’s schedule, the EPA’s refrigerant leak and recordkeeping rules, the energy code and benchmarking obligations above, and the owner’s own program, which many base on ASHRAE/ACCA 180 for commercial HVAC inspection and maintenance. ASHRAE 15 governs the machinery room safety features that a repair must leave in working order, such as refrigerant detectors and ventilation.

An Illinois chiller maintenance calendar built around summer and winter
WhenTaskReason in Illinois
Each refrigerant additionLeak rate calculation and recordRequired for HFC machines of 15 pounds or more from January 1, 2026
March and AprilTube inspection or cleaning, tower startup, safeties and controls checkPrepares the machine for humid summer lift
June to AugustApproach temperature trending, purge run time review, tower performance checksCatches fouling before a high-pressure trip on a humid afternoon
AnnuallyOil and refrigerant analysis, vibration readings, starter and motor testsFinds compressor wear before peak season
Every few yearsEddy current testing and compressor inspection by run hoursSets the retube or replacement timeline
October and NovemberGlycol strength test, drain-down or freeze protection, heat tracing and basin heater checksPrevents the split tubes and frozen towers of an Illinois winter

Paul Industries offers that calendar as chiller service in Illinois under a single agreement that can include the towers, pumps, glycol and piping. Plant operators asking how often should chiller tubes be cleaned get an answer from their own approach temperature trend: once a year is a common baseline on open tower systems, and a rising approach between cleanings shows when to bring the date forward.

Controls, starters and power quality on Illinois chillers

Controls, starters and power quality account for a large share of Illinois chiller calls that look like refrigeration faults at first, because a chiller that trips on a voltage sag, a failed transducer or a drifting flow switch shuts down exactly as it would for a real refrigerant problem. Summer thunderstorms across northern and central Illinois bring momentary outages and sags, and a chiller that does not restart cleanly afterward leaves the building warm until someone resets it.

Paul Industries reads the controller’s fault log before touching the refrigerant circuit, then checks the sensors that feed the control logic: leaving water temperature, condenser and evaporator pressure transducers, flow proving switches and oil pressure sensors. Solid-state and variable frequency drive starters are inspected for heat damage, failed cooling fans and loose terminations, and their restart settings are reviewed so the machine returns on its own after a short power interruption where the owner wants it to. Where the plant has several chillers, the sequencing controls are tested so a tripped machine hands its load to the next one instead of leaving the loop short. Those checks cost little against a compressor replacement made for a fault that was never in the compressor.

Who repairs chillers in Illinois?

Paul Industries repairs chillers in Illinois as an East Coast contractor headquartered at 256 Shore Drive in Kilmarnock, Virginia, taking chiller repair, overhaul, retrofit and replacement work across the state and in all 50 states. Paul Industries works on centrifugal, screw, scroll and absorption machines of the major makes, with brand-specific detail on Trane chiller repair, York chiller repair and Carrier chiller repair.

Centrifugal chiller repair, screw compressor rebuilds, HVAC chiller repair at hospitals and campuses, and industrial chiller repair in Illinois process plants all run under one contract that can also cover the tower, pumps, controls and the piping between them. Unplanned failures are handled under emergency chiller repair service with the same diagnosis and records. Data hall plants follow the redundancy planning described on data center cooling in Illinois, and the headquarters-state view of the same work is on chiller repair in Virginia. Owners with buildings in several states can compare chiller repair in Pennsylvania, and the wider regional view is on the Midwest page.

Chiller repair cost in Illinois: what sets the number

Chiller repair cost in Illinois depends on the fault and its parts, the machine’s size and type, refrigerant recovery and recharge, access to the mechanical room, rigging for large components, temporary cooling, and the season the work falls in. Replacing a sensor or a control board costs far less than rebuilding a compressor, and a freeze repair that contaminates the refrigerant circuit adds dehydration, oil and refrigerant to the tube work.

HVAC chiller replacement cost adds demolition, rigging through the building or by crane, electrical work, new piping connections, controls integration and permits under the Chicago or state energy code. Paul Industries quotes each repair once the fault is found, itemizing parts, refrigerant and labor, and sets a replacement budget next to any major repair so both options sit on the owner’s desk at once.

Chiller repair and maintenance from Paul Industries in Illinois

Paul Industries delivers chiller repair and maintenance across Illinois: diagnosis, leak repair and EPA records, compressor and motor work, freeze damage repair, tube cleaning and eddy current testing, overhauls, retrofits, and supply and installation of replacement chillers, from design-build replacements to supply-only equipment. For a repair, send a nameplate photo, the refrigerant type and charge, the fault codes and a week or two of logs; for a replacement study, add the building or process load profile and the electric tariff. Call 201-450-8280 or request a quote, and see the Illinois page for the rest of the plant work Paul Industries delivers in the state.

Standards referenced: EPA Emissions Reduction and Reclamation rule, 40 CFR 84.106 · EPA Technology Transitions rule (40 CFR Part 84) · Clean Air Act Section 608 · Chicago Energy Benchmarking Ordinance · 2022 Chicago Energy Transformation Code · Illinois Energy Conservation Code (2024 IECC) · ASHRAE 15 · ASHRAE/ACCA 180 · AHRI 700

Frequently asked questions

Who provides chiller repair in Chicago and Cook County?

Paul Industries provides chiller repair in Chicago and across Cook County, from Loop office towers and hospital plants to industrial buildings in the western and southern suburbs. Chicago machines are often large water-cooled centrifugal chillers in basement or mid-building plant rooms, so repairs are planned around rigging paths, building access rules and the shoulder seasons. Paul Industries plans the diagnostic visit from the nameplate data and the plant’s recent logs.

Does Paul Industries repair chillers on the North Shore and in Lake County?

Paul Industries repairs chillers at North Shore and Lake County sites, including pharmaceutical and biologics plants, hospitals and corporate campuses. Process chillers serving validated manufacturing areas are repaired with change records and test results the plant’s quality system can file, and comfort chillers are scheduled around the campus load. Paul Industries plans the repair window with the facility team before any machine is isolated.

Who handles industrial chiller repair in Rockford, Peoria and Decatur?

Paul Industries handles industrial chiller repair in Rockford, Peoria, Decatur and the rest of downstate Illinois, where process chillers serve aerospace and machining plants, agri-processing and food lines. Those machines are often air-cooled or glycol units outdoors, so coil condition, low-ambient controls and freeze protection are checked on every visit. Repairs are timed to production schedules, with likely parts carried for the planned window.

Is chiller repair available in the Metro East and Springfield?

Paul Industries takes chiller repair work in the Metro East, from Wood River and Granite City to Collinsville, and in Springfield and central Illinois, at refineries, chemical plants, hospitals and state buildings. Ameren Illinois serves much of that territory within the MISO market, so energy figures used in a repair or replace study use Ameren tariffs rather than ComEd’s. Paul Industries prices each job after diagnosis.

Does Paul Industries handle Trane chiller repair, York chiller repair and Carrier chiller repair in Illinois?

Paul Industries repairs Trane, York and Carrier chillers in Illinois, along with Daikin and other major makes, covering centrifugal, screw and scroll machines. Brand-specific faults such as purge problems on low-pressure centrifugal machines or slide valve wear on screw compressors are diagnosed from the operating data and the machine’s own fault history. Replacement parts are matched to the serial number before the repair is scheduled.

What is included in a chiller repair service visit in Illinois?

A chiller repair service visit from Paul Industries starts with the alarm history and operating logs, then measures pressures, temperatures, approaches, oil condition and electrical values under load. The technician locates the fault, explains the repair options with parts and refrigerant shown separately, and completes the repair once approved. The visit closes with a run test, safeties checked and a written report including any EPA leak rate records.

How should an Illinois facility choose a chiller repair company?

An Illinois facility choosing a chiller repair company should look for diagnosis from operating data, experience with freeze damage and low-pressure centrifugal machines, written EPA leak records, and the ability to repair the tower, pumps and piping under the same contract. Paul Industries meets each of those points and gives repair and replacement prices side by side. Call 201-450-8280 to start with a diagnostic visit.

How often should chiller tubes be cleaned on an Illinois cooling tower system?

Condenser tubes on an open cooling tower system in Illinois are typically cleaned once a year, before the cooling season, and more often when the approach temperature climbs between cleanings. Evaporator tubes on a closed chilled water loop usually need cleaning far less often. Paul Industries trends the approach temperatures, inspects the tubes when the heads come off, and sets the next cleaning date from what the tubes show.

What happens when a chiller evaporator freezes in an Illinois winter?

When an evaporator freezes, ice splits one or more tubes and water can enter the refrigerant circuit, contaminating refrigerant, oil and, on hermetic machines, the motor windings. Paul Industries recovers and tests the refrigerant, pressure tests the bundle, plugs or replaces failed tubes, dries the circuit under deep vacuum, replaces the oil and recharges. The repair ends with the freeze cause corrected so it does not repeat.

How is glycol strength set for outdoor chillers in northern Illinois?

Glycol strength for an outdoor chiller in Illinois should protect the loop below the lowest temperature it can see, and O’Hare’s 99.6 percent design condition is 6 degrees below zero, with colder nights on record. Many northern Illinois systems use propylene or ethylene glycol mixtures with freeze points well below that figure. Paul Industries tests freeze point and inhibitor levels each autumn and corrects dilution caused by summer water top-ups.

Can an R-123 centrifugal chiller in a Chicago tower still be repaired?

An R-123 centrifugal chiller can still be repaired and serviced, since reclaimed and previously produced R-123 may be used for existing machines after the 2030 phaseout. Leak tightness and purge performance protect that limited supply, so repairs focus on seals, gaskets and the purge unit. Paul Industries also prices a long-term path for the tower owner: continued repair, a retrofit where available, or a replacement planned before a major failure.

Does Chicago's benchmarking ordinance require chiller upgrades?

Chicago’s Energy Benchmarking Ordinance requires buildings larger than 50,000 square feet to report energy use each year and verify the data every three years; it sets reporting duties rather than mandating a chiller upgrade. The reported data, however, exposes a chiller plant that has drifted from its rated efficiency. Paul Industries measures plant kilowatts per ton and shows owners which repairs improve the next report.

At what point does an Illinois chiller need a full overhaul?

An overhaul makes sense when run hours reach the manufacturer’s inspection interval, when oil analysis and vibration readings show bearing or gear wear, or when several faults point to an aging compressor. Overhauls are planned for spring or autumn in Illinois so the machine returns before peak load. Paul Industries opens the compressor, replaces bearings, seals and worn parts, tests the motor and returns the chiller with a full report.

How much does a summer chiller failure cost an Illinois plant?

The cost of a summer failure is mostly the cost of the lost cooling: scrapped product, slowed lines, rented temporary chillers, and overtime to recover production. The repair itself is often the smaller number. Paul Industries reduces that exposure with spring inspections, oil and vibration trending, and permanent temporary-cooling connections installed during planned outages so a rental machine connects without cutting into the plant piping.

How do hospitals and data centers keep cooling during an Illinois chiller repair?

A chiller in a plant with redundancy can be repaired while the building keeps cooling, provided the remaining machines carry the expected load for the full outage window. Paul Industries confirms that capacity before isolating anything, writes a step-by-step procedure for the switchover, and connects temporary cooling where margin is thin. Before it rejoins the plant, the repaired chiller carries load while each safety is proven.

What information does a chiller repair quote in Illinois start from?

Useful pricing inputs are the nameplate data, the refrigerant and how many pounds the machine holds, the fault codes it has logged, a few weeks of operating data, the most recent service and eddy current reports, and the refrigerant addition history. Photos of the nameplate and the plant room help with access planning. Paul Industries uses that information to plan the diagnostic visit and prices the repair with parts, refrigerant and labor shown separately.

Does glycol chiller repair differ for a food plant compared with an office building?

Glycol chiller repair at a food plant differs in timing, chemistry and hygiene: the work fits between production runs, the glycol is often food-grade propylene glycol, and any opening of the process loop follows the plant’s sanitation rules. Office systems usually use glycol only for freeze protection on outdoor coils or dry coolers. Paul Industries checks freeze point, inhibitor and pump performance on both.

Need a chiller repaired anywhere in Illinois?

Tell us the chiller’s make and model, its refrigerant, the fault codes it is showing and how the plant has been running. Call 201-450-8280 or request a quote.