Paul Industries provides chiller repair in Maryland for hospitals, laboratories, manufacturing plants, universities, office buildings and data centers, working on centrifugal, screw and scroll machines from Baltimore and Annapolis to the I-270 corridor, Frederick, Hagerstown and the Eastern Shore. Paul Industries is headquartered at 256 Shore Drive, Kilmarnock, Virginia, and repairs, overhauls, retrofits, maintains and replaces chillers across the state. Maryland adds its own refrigerant rule for new chillers, two building performance programs and an operator license law to the federal rules every owner already follows.
Request a quote or call 201-450-8280
What does chiller repair in Maryland cover?
Chiller repair in Maryland covers diagnosis of faults and alarms, refrigerant leak search and repair with the federal leak rate records, compressor rebuilds and bearing replacement, motor and starter repair, control faults, tube cleaning and eddy current testing, purge unit repair on low-pressure machines, and the startup and load test that proves the machine is ready to rejoin the plant. Paul Industries does that work on water-cooled and air-cooled machines, from single packaged units serving one building to multi-chiller central plants on hospital and university campuses.
The faults themselves are the same in any state, and the national guide to symptoms and repair methods is on the chiller repair page. What Maryland changes is the context around the repair: which machines fall under state inspection or operator licensing, what refrigerant a replacement may use, and how chiller efficiency now counts toward a building’s performance standard. Those points decide whether a repair is the right answer and how it is documented.
When a repair will run longer than a building can ride on its remaining machines, Paul Industries connects a temporary chiller. Plants with valved and capped connections on the chilled water mains take a rental unit with modest field work; plants without them get permanent connection points installed during the outage, so any later emergency begins with the piping already in place. Power for the rental unit, a level pad and a route for hoses are settled before the original machine is opened.
Does Maryland inspect chillers as pressure vessels?
Maryland’s Boiler and Pressure Vessel Safety Act, in Title 12, Subtitle 9 of the Public Safety Article, excludes the water-containing part of an air-conditioning or refrigeration condenser or evaporator when the system uses halocarbon refrigerant, was built to the edition of ASHRAE 15 in force when it was made, and is designed for no more than 300 psig and 210 degrees Fahrenheit. The same section excludes compressors and pumps as mechanical devices, and water vessels that use air only as a cushion, such as many chilled water expansion tanks, within the same pressure and temperature limits.
A standard halocarbon chiller’s water boxes and tube bundles therefore sit outside the state inspection program, while other vessels in the plant room may fall inside it. Compressed air receivers, steam vessels and hot water vessels above the exemption limits, and steam or hot water boilers driving absorption chillers, follow the inspection and certificate rules in COMAR 09.12.01 under the Division of Labor and Industry. Paul Industries lists which vessels in a chiller plant carry state certificates before a repair outage, so a vessel opened or modified during the work is handled under the right rules. Boilers that share the plant are covered on boiler repair in Maryland.
Who must operate a chiller plant under Maryland’s Stationary Engineers Act?
Maryland’s Stationary Engineers Act requires a stationary engineer holding the appropriate license grade to oversee the operation of a power plant, plant of machinery or boiler operating above 15 psi with at least 30 horsepower, and the State Board lists chillers among the equipment the Act reaches. The grade is set by the horsepower of the largest single piece of equipment in the plant, not by the combined total, and the requirement applies statewide with no reciprocity for out-of-state licenses.
The grades step up with size: Grade 1 for equipment of 500 horsepower or more, Grade 2 for 300 to 499, Grade 3 for 100 to 299, and Grades 4 and 5 for 30 to 99 horsepower. As an illustration, a 500-ton centrifugal chiller drawing about 0.6 kilowatts per ton runs a compressor of roughly 400 horsepower, which falls in the Grade 2 band. The operator requirement belongs to the building, but it affects repair planning: the plant’s engineer signs off on lockout, isolation and return to service, and repairs that change a machine’s operation are recorded in the plant log the engineer keeps.
Maryland’s HFC rule and the federal refrigerant rules
Maryland’s HFC rule, COMAR 26.11.33, adopted federal prohibitions on certain hydrofluorocarbons as state law, and from January 1, 2024 it bars new centrifugal and positive displacement chillers used for comfort cooling from using listed refrigerants that include HFC-134a, R-410A, R-407C and R-404A. The rule applies to new equipment and requires labels on chillers shipped without a refrigerant charge; existing chillers keep running and are serviced on the refrigerant they hold.
Federal rules sit on top. Under the EPA’s Technology Transitions rule, a new comfort-cooling chiller installed since January 1, 2025 needs a refrigerant whose global warming potential is under 700, and the same limit reached most industrial process chillers on January 1, 2026. Under the Emissions Reduction and Reclamation rule, from January 1, 2026 every appliance holding 15 pounds or more of an HFC needs a leak rate calculation each time refrigerant is added; a comfort cooling machine leaking above 10 percent a year, or a process machine above 30 percent, gets 30 days to fix the leak (120 if a process shutdown is required), followed by verification tests.
| Refrigerant | Where it is found | Maryland rule | Federal rule | Effect on a repair |
|---|---|---|---|---|
| HFC-134a | Centrifugal and screw chillers from the 1990s onward | Barred in new comfort chillers from 2024 | Leak rate records at 15 lb or more | Existing machine repaired and recharged as before; a replacement uses another refrigerant |
| R-410A | Scroll and small air-cooled chillers | Barred in new comfort chillers from 2024 | GWP limit of 700 for new comfort chillers | Repairable; plan the replacement refrigerant before a major failure |
| R-123 | Low-pressure centrifugal machines in hospitals and campuses | Existing machines unaffected | Import allowances end in 2030; reclaimed supply continues | Purge and leak tightness protect a shrinking supply |
| R-22 | Older screw and reciprocating units | Existing machines unaffected | Production and import ended in 2020 | Short repair horizon; replacement or conversion priced alongside |
| Low-GWP HFOs and blends | Chillers installed since the rules took effect | Permitted for new equipment | Meet the 700 GWP limit | Technicians follow the refrigerant’s safety class and handling procedures |
How Maryland’s building performance standards change a chiller decision
Maryland’s Building Energy Performance Standards, created by the Climate Solutions Now Act of 2022, require owners of commercial and multifamily buildings of 35,000 square feet or more to benchmark energy use each year in ENERGY STAR Portfolio Manager and to reach net-zero direct greenhouse gas emissions by 2040. The 2025 amendments (HB 49) excluded hospitals, joining historic buildings, elementary and secondary schools, manufacturing and agricultural buildings among the excluded categories.
The state standard measures direct emissions, the fuel burned on site, so electric chillers add nothing to it while gas-fired absorption chillers, engine-driven chillers and the boilers that feed steam absorption machines do. When a gas-fired absorption machine fails, the repair or replace decision now includes whether an electric chiller, perhaps a heat recovery chiller that also makes hot water, would cut the building’s direct emissions toward the 2040 target.
Montgomery County runs its own program, and buildings there follow the county standard instead of the state one. The county covers buildings of 25,000 gross square feet or more and measures normalized net site energy use intensity, so every kilowatt-hour a chiller plant uses counts against the building’s target. In Bethesda, Silver Spring, Rockville and Gaithersburg, a chiller’s efficiency at part load is as much a compliance figure as an operating cost, and tube cleaning, condenser water reset and control tuning carry more weight than they used to.
How Maryland’s summer and geography work a chiller
Maryland’s summer works a chiller with heat and humidity together. NOAA’s 1991 to 2020 normals give Baltimore an average July afternoon of 89 degrees Fahrenheit and an average July night of 68, and those humid nights keep latent load on the plant long after sunset. Geography adds variety, from salt air along the Chesapeake Bay and the Atlantic coast to colder winters in Frederick, Hagerstown and the western mountains.
| Region | Typical buildings | Common chiller issues | Repair and service focus |
|---|---|---|---|
| Baltimore and its suburbs | Academic medical centers, universities, older offices, manufacturers | Aging R-123 and R-22 machines, tube fouling, tight plant rooms | Overhauls, rigging through existing openings, replacement planning |
| I-270 corridor: Rockville, Gaithersburg, Germantown | Biotech labs and manufacturing, federal research buildings | High outdoor air loads, around-the-clock operation, county energy targets | Part-load efficiency, redundancy checks, staged outages |
| Annapolis and the Bay shore | State government buildings, campuses, waterfront offices | Salt corrosion on air-cooled coils and cabinets | Coil inspection and coating, leak checks at corroded joints |
| Frederick, Hagerstown and Western Maryland | Data centers, plants, distribution centers | Freeze risk in winter, long economizer seasons | Glycol strength, winter layup, free cooling controls |
| Salisbury and the Eastern Shore | Poultry and food processing, hospitals, campuses | Process water chillers tied to production, salt air | Repairs between production runs, coil and enclosure protection |
| Southern Maryland and Prince George’s County | Government, healthcare, offices | Long cooling seasons, mixed equipment ages | Maintenance programs, leak rate records, replacement studies |
Free cooling extends the value of a chiller plant in the colder parts of the state. A plate heat exchanger between the condenser water and chilled water loops lets the cooling tower carry the load directly on cold days, and plants in Frederick, Hagerstown and Garrett County see many such hours each winter. Paul Industries repairs and retrofits these waterside economizers, checks the changeover controls, and confirms the tower and exchanger stay protected from freezing when the plant switches modes.
Why are chillers important to Maryland hospitals, labs and plants?
Chillers are important to Maryland hospitals, laboratories and plants because they hold the temperature and humidity that patient care, research and production depend on, not just comfort. Baltimore’s academic medical centers, including Johns Hopkins Hospital and the University of Maryland Medical Center, and the biotech laboratories along the I-270 corridor run their cooling plants all year, and a chiller outage there can close operating rooms, spoil experiments or stop a batch.
Hospitals and medical centers
Hospital chiller repairs are planned around the backup capacity left when one machine is out. Paul Industries checks the remaining chillers, pumps and towers against the expected load for the outage window, confirms which air handlers serve operating rooms, sterile processing, pharmacies and isolation rooms, and arranges temporary cooling where the margin is thin. Work follows the hospital’s infection control and outage procedures, and the machine is run under load before it rejoins the plant.
Laboratories on the I-270 corridor
Laboratory buildings in Rockville, Gaithersburg and Germantown often run on 100 percent outside air with high air change rates, so their chillers carry heavy latent load through Maryland summers and rarely see light duty. Chiller repair in Rockville and the rest of the corridor is usually staged at night or on weekends with redundancy confirmed first, and labs with classified rooms coordinate the outage with the room monitoring described on cleanrooms in Maryland.
Water chiller repair at food and process plants
Water chiller repair at Maryland food and process plants follows the production calendar. Poultry processors around Salisbury, food and beverage plants in the Baltimore region and manufacturers in Frederick and Hagerstown use process chillers on product water, glycol and jacketed vessels, and a failure stops the line. Paul Industries schedules repairs between runs, brings likely parts for the planned window and checks glycol strength and process water quality at the same visit. Process piping connected to the chillers is covered on process piping in Maryland.
Data center chiller plants
Data center chillers in Frederick County and the Washington suburbs run year round, and each repair takes one machine out under a written procedure that confirms the remaining capacity before isolation and again before return to service. The broader cooling plant is covered on data center cooling systems in Maryland.
How long does a chiller last in Maryland service?
A well-maintained centrifugal chiller often lasts more than 25 years; ASHRAE’s owning and operating cost data put the median service life of centrifugal chillers above 25 years. Maryland machines reach that age with heavy run hours, because humid summers and year-round hospital, lab and data center loads keep them working, so compressor overhaul and tube inspection intervals come around sooner than on lightly used machines.
Age alone rarely decides a repair. A 25-year-old centrifugal machine with sound tubes, a tight refrigerant circuit and a current refrigerant can earn a compressor overhaul; a younger machine with widespread tube wall loss and a rising leak rate may not. Paul Industries judges each machine on test results: eddy current data on the tubes, oil and vibration analysis on the compressor, leak history under the federal records, and measured efficiency against the original rating.
| Question | Repair or overhaul | Replace |
|---|---|---|
| Is the refrigerant still serviceable? | HFC-134a or a low-GWP refrigerant with available supply | R-22, or R-123 with no supply plan past 2030 |
| What do the tubes show? | Limited wall loss, few plugged tubes | Wall loss spread across the bundle |
| Is the leak history clean? | One leak found, repaired and verified | Repeated leak rate exceedances |
| Does the building face an energy target? | Machine efficiency near its rating; target met by tuning | Efficiency gap blocks a Montgomery County site EUI target |
| Is it fired by gas? | Electric chiller with a repairable fault | Gas absorption machine in a building working toward the state’s 2040 direct emissions goal |
| Does it still fit the load? | Load unchanged | Load grown or shrunk so far that the machine runs poorly |
How much does a chiller cost to run in Maryland?
A chiller’s running cost in Maryland is its kilowatt draw multiplied by its hours and the electric rate. EIA figures for 2024 put the average industrial rate in Maryland at 10.01 cents per kilowatt-hour, well above the 8.13 cent national average. As an illustration, a 500-ton chiller drawing 0.6 kilowatts per ton uses 300 kilowatts at full load; over 2,500 equivalent full-load hours a year that is 750,000 kilowatt-hours, or about $75,000 at the state average industrial rate.
The same arithmetic prices the gap between repair and replacement. A 400-ton machine that improves by 0.2 kilowatts per ton after replacement saves about 200,000 kilowatt-hours over 2,500 equivalent full-load hours, or about $20,000 a year at that rate. Both figures are examples with stated assumptions; Paul Industries runs the calculation on the owner’s trend data, tonnage and actual tariff, whether BGE, Pepco, Delmarva Power, Potomac Edison or SMECO, before recommending a path.
Chiller maintenance procedures for Maryland plants
Chiller maintenance procedures for Maryland plants combine the manufacturer’s schedule, the federal leak rate and recordkeeping rules, and the operating log the plant’s stationary engineer keeps, with ASHRAE/ACCA 180 serving many owners as the written program. A plan that ties each task to a season works best in Maryland, where the same machine faces humid peaks in July and freeze risk in January.
| Interval | Procedure | Maryland reason |
|---|---|---|
| Each refrigerant addition | Leak rate calculation and record | Federal rule for HFC machines of 15 lb or more since January 1, 2026 |
| Daily, by log or monitoring | Pressures, approaches, oil levels, purge run time, amps | Operating log kept under the plant’s stationary engineer |
| Spring, before the humid season | Tube cleaning or inspection, tower startup, safety and control checks | Sets up the machine for months of high lift |
| Annually | Oil and refrigerant analysis, vibration, starter and motor tests | Finds compressor wear before July peaks |
| Annually, for covered buildings | Energy data review for the benchmarking report | State BEPS reporting each June 1; county targets in Montgomery County |
| Every few years | Eddy current testing; compressor inspection per run hours | Year-round loads bring these sooner |
| Autumn, idle machines | Drain or glycol-protect evaporators and outdoor piping | Freeze damage in Frederick, Hagerstown and Western Maryland |
Paul Industries delivers that program as chiller service in Maryland under service contracts, checks reclaimed refrigerant against AHRI 700 purity limits, and covers the cooling towers alongside the chillers through cooling tower repair.
Who repairs and services chillers in Maryland?
Paul Industries repairs and services chillers in Maryland, providing chiller repair in Baltimore and its suburbs, chiller repair in Annapolis and along the Bay, and work on the I-270 corridor, in Frederick and Hagerstown, in Prince George’s and Montgomery counties, in Columbia and Howard County, around Aberdeen and Harford County, in Salisbury and on the Eastern Shore, and in Southern Maryland. The company has its headquarters in Kilmarnock, Virginia, was formerly based in northern New Jersey and then Pennsylvania, and takes chiller work along the East Coast and in all 50 states.
Paul Industries repairs centrifugal, screw and scroll chillers of every major make, and one contract takes in the condenser water, towers, pumps and controls as well, which keeps the diagnosis with one firm when a fault crosses equipment boundaries. For data center plants, repairs follow the redundancy rules described on data center mechanical contractor in Maryland. Owners with buildings in several states can compare the headquarters-state approach on chiller repair in Virginia and the inspection rules on chiller repair in New Jersey.
What does chiller repair cost in Maryland?
The cost of chiller repair in Maryland depends on six things: what failed and which parts replace it, the size and type of machine, how much refrigerant is recovered and recharged, how hard the plant room is to reach, whether temporary cooling is needed, and what time of year the work falls in. A control or bearing repair costs a fraction of a compressor rebuild, and a rebuild costs a fraction of a replacement, which brings rigging, electrical and piping work with it.
HVAC chiller replacement cost in Maryland also depends on refrigerant choices made by the state and federal rules, on structural and electrical changes for the new machine, and on whether the building’s performance target justifies a higher-efficiency selection. Paul Industries prices repairs after diagnosis with parts, refrigerant and labor shown separately, and gives a budget range for replacement from comparable scope alongside any major repair so the two can be compared.
Chiller repair, service and replacement from Paul Industries in Maryland
Paul Industries repairs, overhauls, retrofits, maintains, supplies and installs chillers for Maryland hospitals, laboratories, plants, campuses, office buildings and data centers, with supply-only, design-build and complete installation routes for replacements. For a repair, share the nameplate data, refrigerant type and charge, fault codes and a few weeks of logs; for a replacement study, add the load profile, tariff and any BEPS target. Call 201-450-8280 or request a quote, and see Paul Industries in Maryland for the plant, water and piping services offered across the state.
Standards referenced: Maryland Boiler and Pressure Vessel Safety Act (Public Safety Article, Title 12, Subtitle 9) · COMAR 09.12.01 · Maryland Stationary Engineers Act · COMAR 26.11.33 (Maryland HFC prohibitions) · Maryland Building Energy Performance Standards (Climate Solutions Now Act of 2022) · Montgomery County Building Energy Performance Standards · Maryland Building Performance Standards · EPA Emissions Reduction and Reclamation rule, 40 CFR 84.106 · EPA Technology Transitions rule · Clean Air Act Section 608 · ASHRAE 15 · ASHRAE/ACCA 180 · AHRI 700
Frequently asked questions
Who handles chiller repair in Baltimore, from downtown hospitals to the county suburbs?
Paul Industries handles chiller repair in Baltimore City and Baltimore County, at hospitals, universities, office buildings and manufacturers in BGE territory. Many Baltimore plants run older R-123 low-pressure centrifugal machines and R-22 units in tight basement plant rooms, so repairs often include purge work, leak tightness and a replacement plan priced alongside. Send the chiller data and alarm history to start the diagnosis.
Does Paul Industries repair chillers in Rockville, Gaithersburg and the rest of the I-270 corridor?
Yes. Paul Industries repairs chillers in Rockville, Gaithersburg, Germantown and Bethesda, where biotech laboratories, research buildings and offices run long hours on high outdoor air loads. Montgomery County’s own building energy standard measures site energy use intensity, so repairs there often add tube cleaning, control tuning and efficiency testing to the fault repair itself.
Who provides chiller repair in Annapolis and along the Chesapeake Bay?
Paul Industries provides chiller repair in Annapolis, Anne Arundel County and other Bay shore areas, where salt-laden air corrodes aluminum fins, copper tubes and cabinets on air-cooled chillers. Corroded brazed joints are a frequent leak source. Each service visit near the water includes coil and enclosure inspection, and Paul Industries recommends coating or coil replacement before corrosion turns into refrigerant loss.
Does Paul Industries service chillers in Salisbury and on the Eastern Shore?
Paul Industries services chillers in Salisbury and across the Eastern Shore, at poultry and food processors, hospitals and campuses in Delmarva Power territory. Process water and glycol chillers at food plants are repaired between production runs, with glycol strength and water quality checked at the same visit, and coastal machines get the same corrosion inspection as Bay shore sites.
Is a chiller's water box covered by the Maryland boiler and pressure vessel law?
The water-containing part of a condenser or evaporator is excluded for halocarbon chillers built to ASHRAE 15 with design limits of 300 psig and 210 degrees Fahrenheit or less, under Section 12-903 of the Public Safety Article. Compressors and pumps are also excluded as mechanical devices. Boilers, steam vessels and compressed air receivers in the same plant room may still need state certificates under COMAR 09.12.01.
Does a Maryland chiller plant need a stationary engineer license holder on duty?
Maryland’s Stationary Engineers Act requires a stationary engineer with the right license grade to oversee plants of machinery operating above 15 psi with at least 30 horsepower, and the State Board names chillers among covered equipment. The grade follows the largest single piece of equipment. Paul Industries plans lockout, isolation and return to service with the plant’s engineer on every repair.
Can a new HFC-134a chiller still be installed in Maryland?
Maryland’s HFC rule, COMAR 26.11.33, bars HFC-134a, R-410A and other listed refrigerants in new centrifugal and positive displacement comfort-cooling chillers from January 1, 2024, and federal rules limit new comfort chillers to refrigerants below 700 GWP from 2025. Existing HFC-134a machines keep running and are repaired and recharged as before; a replacement uses a compliant low-GWP refrigerant.
Do Maryland's BEPS rules require an old chiller to be replaced?
The state program sets direct emissions targets reaching net zero by 2040, so electric chillers add nothing to a building’s direct emissions while gas-fired absorption or engine-driven machines do. Montgomery County’s program measures site energy use intensity, which counts every chiller kilowatt-hour. Neither names chillers for replacement, but both make efficiency and fuel type part of the repair or replace decision.
Are hospital chiller plants in Maryland covered by the state building performance standard?
HB 49 of 2025 added hospitals to the categories excluded from the state’s Building Energy Performance Standards, alongside manufacturing, K-12 schools, historic and agricultural buildings, effective October 1, 2025. Owners still apply through the state portal to confirm the exclusion, and other healthcare buildings such as ambulatory surgical centers remain covered. Hospital chillers still fall under the federal leak rate and refrigerant rules.
Why are chillers important enough to need redundancy in a Maryland lab building?
Laboratory buildings on 100 percent outside air rely on their chillers to dehumidify and cool every cubic foot of supply air, and in a humid Maryland summer the load stays high day and night. Losing a machine can push labs out of their temperature and humidity limits quickly, so most lab plants carry a spare chiller and staged repairs around it.
How long does a chiller last if it serves a Maryland hospital around the clock?
ASHRAE data put the median service life of centrifugal chillers above 25 years, but a hospital machine accumulates far more run hours each year than an office chiller. With good water treatment, tube cleaning, oil analysis and leak control, a hospital centrifugal machine reaches that age; without them, tube wall loss and compressor wear arrive earlier. Paul Industries tracks run hours and test results to forecast when an overhaul is due.
What is the chiller maintenance cost for a Maryland central plant?
Chiller maintenance cost depends on the number and size of machines, refrigerant type, whether towers, pumps and water treatment are included, tube cleaning and eddy current frequency, and how many outages the building allows. Paul Industries prices a service program from the equipment list and operating hours, with each task and interval shown, so the owner can compare it with the repair history the plant has carried.
Which months suit a chiller overhaul in Maryland?
Late autumn through early spring suits most Maryland buildings, because cooling loads are low and a machine can come out of service with little risk. Campuses tend to choose winter break, plants work to their shutdown calendars, and buildings with year-round load such as hospitals, labs and data centers take one machine down in whatever month the spare capacity is proven.
How should chillers in Frederick, Hagerstown and Western Maryland be protected in winter?
Idle chillers in Frederick, Hagerstown and the western counties should have evaporators and exposed piping drained or protected with glycol at the right strength, because a frozen tube bundle splits and floods the refrigerant circuit. Oil and crankcase heaters stay powered. Machines running year round for data centers or labs need freeze protection on outdoor coils and free cooling controls tuned for cold nights.
Can an absorption chiller be replaced with an electric chiller in a Maryland building?
Yes, and the state’s direct emissions goal makes it a common question. The steam or gas supply to the absorption machine is retired or reassigned, the electrical service is checked for the new compressor load, and the cooling tower is often resized because electric machines reject less heat per ton. Paul Industries prices both repair of the absorption machine and the electric replacement, including heat recovery options.
What does chiller service in Maryland include under a Paul Industries contract?
Chiller service in Maryland under a Paul Industries contract covers seasonal startup and layup, log review, leak rate records, oil sampling, refrigerant purity checks, vibration trending, tube brushing, eddy current tests at set intervals, and energy data for the building’s BEPS report where it applies. Contracts can add the cooling towers, pumps and water treatment so one program covers the whole plant.
Which chiller details speed up a repair price for a Maryland building?
Share the nameplate data, refrigerant type and charge, fault history, recent operating logs, the last service report and refrigerant addition records. For coastal machines, add photos of coils; for buildings under a BEPS target, add the latest benchmarking result. Paul Industries plans the diagnostic visit from that data and prices the repair with parts, refrigerant and labor shown separately.
Does Paul Industries repair process chillers at plants in Aberdeen and Harford County?
Paul Industries repairs process and comfort chillers at plants, laboratories and distribution buildings around Aberdeen, Havre de Grace, Bel Air and the rest of Harford County. Process machines are repaired between production runs with likely parts on hand for the window, and glycol and process water conditions are checked at the same visit so the repair addresses the cause as well as the failed part.
Need a chiller repaired anywhere in Maryland?
Share the nameplate, refrigerant type, fault codes and a few weeks of logs. Call 201-450-8280 or request a quote.
