Paul Industries provides industrial welding services in Washington, performing code pipe welding, structural welding, pressure equipment repairs, tank work and maintenance welding at refineries, food plants, aerospace and biotech sites, terminals and utilities across the state. Washington has no individual state welder license, but its structural welders are qualified through a statewide building officials' program and Seattle's own approval rule, its plant hot work follows chapter 296-24 WAC, and its boiler, vessel and refinery welding carries state filing and review steps. Paul Industries welds to ASME, AWS and API codes with qualified procedures and welders, and documents each weld for the inspector and the owner.

Request a quote or call 201-450-8280

Headquarters 256 Shore Drive, Kilmarnock, Virginia
Structural welders WABO certification statewide; Seattle approval under Director's Rule 15-2015
Hot work rule WAC 296-24 Part I, sections 296-24-680 to -722
Boiler and vessel repairs NBIC Part 3, R-1 or R-2 filed within 45 days (WAC 296-104-503)
Refineries Part B hot work, change and startup reviews since December 27, 2024
Reviewed November 2026

What do industrial welding services in Washington include?

Industrial welding services in Washington include process and utility pipe welding to ASME B31.3 and B31.1, sanitary orbital welding to ASME BPE, structural steel welding to AWS D1.1, repairs and alterations to boilers and pressure vessels under the National Board Inspection Code, storage tank repairs under API 653, in-service welding and hot taps, and repair welding on equipment frames, conveyors, platforms and supports. Each job pairs a welding procedure specification with qualified welders, the right examination and a record set that matches the code behind the work.

The national industrial welding services page explains processes, materials and examination methods in general terms. This page covers what Washington adds: how structural welders are qualified here, how the building code inspects structural welds, which hot work rules apply in plants, what the state asks after a welded boiler or vessel repair, how the refinery process safety rule affects welding, and how weather on each side of the Cascades shapes field welding.

Washington State welding certification: WABO and Seattle's structural rule

Washington State welding certification for structural work runs through the Washington Association of Building Officials, whose welder certification program gives building departments a uniform way to determine and document a welder's qualification, with tests based on the American Welding Society standards and given at approved facilities such as South Seattle College. Washington's Department of Labor and Industries does not issue an individual welder license; it registers contractors, and every contractor working in the state must be registered under chapter 18.27 RCW.

Seattle adds its own rule. Seattle's Director's Rule 15-2015 sets the department's requirements for approving welders who erect structural steel on projects under a City of Seattle building permit, and the Seattle Building Code ties welder qualification to its special inspection provisions for structural steel. A plant expansion, a mezzanine or a pipe rack inside Seattle therefore needs welders approved under the city's rule, while the same work in Tacoma or Spokane goes to that jurisdiction's building official, which usually looks for the statewide program's cards.

Owners often ask which records prove a welder is qualified on their job. For structural work the answer is the building official's accepted card or the Seattle approval; for code pressure work it is the welder performance qualification record for the procedure in use, with a continuity log showing the welder has used that process within the code's time limit. A welder who holds a structural card is not automatically qualified for pressure piping, and the reverse also holds, so each job file lists welders against the procedures they are qualified to run.

Code welding outside the building code follows the qualification rules of each code: ASME Section IX for boiler, pressure vessel and pressure piping welds, AWS D1.1 for structural steel, AWS D1.6 for structural stainless, and API 1104 for pipelines. Paul Industries qualifies its welding procedures and welders to the code each job requires and keeps the procedure qualification records and welder continuity logs on file for the inspector.

Structural welding under the Washington State Building Code

Structural welding under the Washington State Building Code follows chapter 17 of the International Building Code as the state adopts it, which calls for special inspection of structural steel welding by an approved agency acting for the owner, under the steel quality assurance provisions the code references, with the inspection tasks and their timing set by the weld type and the structure's seismic design. Structural welding Washington State building departments permit is inspected this way whether the steel is a new building frame or a platform added inside an existing plant. Washington has applied the 2021 editions since March 15, 2024, and has scheduled the 2024 editions for May 3, 2027, so the edition is read from the permit date.

Seismic design raises the stakes on structural welds across much of the state. Moment connections, braced frame connections and the welds that anchor equipment platforms and pipe racks carry earthquake loads, and the design documents often call for specific filler metals, weld access holes and examination of critical welds. Paul Industries welds structural steel to the drawings and AWS D1.1, coordinates hold points with the special inspector, and turns over weld maps and inspection reports with the as-built structure. Platforms, supports and steel for equipment are fabricated under structural steel fabrication.

Hot work rules for welding in Washington plants

Hot work in Washington plants is governed by Part I of chapter 296-24 WAC, Welding, Cutting and Brazing, which runs from WAC 296-24-680 to 296-24-722 and covers oxygen-fuel gas systems, arc and resistance welding equipment, fire prevention and protection, welding or cutting of containers, confined spaces, protection of employees, ventilation and work on preservative coatings. Construction sites follow the corresponding construction rules, and every site follows the fire code's welding and hot work chapter as Washington adopts it.

The fire prevention section is where most plant permits begin: combustibles moved or shielded, openings covered, a fire watch posted where the rule calls for one, and extinguishing equipment at hand. Containers that held flammable or toxic material are cleaned and tested before welding, and confined spaces get ventilation, attendants and rescue arrangements. Refineries go further, because Part B of chapter 296-67 WAC contains its own hot work section. Paul Industries writes the hot work plan into each job package, with gas testing, fire watch and isolation set out for every location before the first arc is struck.

Washington rules and codes by type of welding work
WorkQualification codeWashington layerRecords handed over
Structural steel inside SeattleAWS D1.1Director's Rule 15-2015 welder approval; special inspection under the Seattle Building CodeWelder approvals, weld maps, special inspection reports
Structural steel elsewhere in WashingtonAWS D1.1Building official's welder qualification; IBC chapter 17 special inspectionWelder cards, weld maps, special inspection reports
Boiler or pressure vessel repairASME Section IX, NBIC Part 3National Board R program; checklist and R-1 or R-2 within 45 daysR form, procedure and welder records, test record
Refinery piping and equipmentASME Section IX, API 570 and 510Part B hot work, change, damage mechanism and pre-startup reviewsWeld map, examination, hardness and PMI records
Terminal tank repairASME Section IX, API 653Ecology seismic protection and API 653 seismic inspection at Class 1 facilitiesRepair record, examination and test results
Sanitary process tubingASME Section IX, ASME BPEQualification records for FDA-regulated sitesWeld logs, coupons, borescope and passivation records

Welded boiler and pressure vessel repairs in Washington

Welded repairs and alterations to boilers and pressure vessels in Washington follow NBIC Part 3 under the R program of the National Board, and the Authorized Inspector reviews the repair plan before any welding starts. The state's own steps sit around that national process: the quality manual is lodged with Washington before mechanical work begins in the state, and within 45 days of finishing the work the jurisdiction receives the job checklist, signed off by quality control and the inspector holding the R endorsement, together with the R-1 report for a repair or the R-2 report for an alteration.

Typical repair welds include tube replacements and plug welds on boilers, nozzle and shell repairs on vessels, weld buildup on corroded areas, and rerates that change a vessel's design pressure or temperature. Paul Industries plans each repair with the inspector, welds it with procedures qualified to Section IX, examines and tests it, and assembles the filing as the work proceeds. The boiler side of this work is covered on boiler repair in Washington, and new vessels on pressure vessel fabrication in Washington.

Welding at Washington refineries under the Part B rule

Welding at Washington's five refineries, which held 648,200 barrels per day of crude capacity at the start of 2026 by EIA figures, runs under Part B of chapter 296-67 WAC, the refinery process safety standard in force since December 27, 2024. Part B affects welding in four places: its hot work section, management of change for anything that is not replacement in kind, damage mechanism reviews that set material and examination choices, and a pre-startup safety review for every turnaround that confirms repair work met the design specifications.

For a welding contractor the result is a heavier, more structured record, and the welding services Washington refineries specify now read like integrity documents. Refineries specify hardness testing on welds in sour and hydrogen service, positive material identification on alloy components, and examination extents tied to the damage mechanisms in each circuit. Paul Industries welds to those specifications and returns weld maps, examination and hardness records and PMI results indexed by line or equipment number, so the inspection department can close each work order and the startup review can rely on the file.

Pipe welding for Washington food, ammonia and biotech plants

Pipe welding for Washington food, ammonia and biotech plants covers carbon steel ammonia refrigeration piping to IIAR 2 and B31.3 in Columbia Basin cold storage and processing plants, stainless product, CIP and utility lines in fruit, juice, wine and dairy plants, and orbital-welded high-purity tubing to ASME BPE at biotech sites around Seattle, Bothell and Redmond. The common thread is cleanliness and traceability: sanitary welds need full penetration with a smooth, crevice-free interior, and ammonia welds need sound root passes and examination because a leak is a release.

Orbital welding produces consistent, documented welds on sanitary tubing, with weld logs, sample coupons at each change of welder, machine or material, and borescope inspection of the interior. Heat tint left on a stainless weld is removed by pickling and passivation, which passivation services in Washington handles on new and modified systems. Paul Industries installs the piping systems themselves under process piping in Washington.

In-service welding and hot taps on live Washington lines

In-service welding on live Washington lines, including hot taps, sleeves and branch connections welded while the pipe carries product, is used when a refinery header, a food plant steam main or a utility line cannot be shut down for a tie-in or repair. The work depends on a wall thickness survey at the weld location, a welding procedure qualified for in-service conditions that controls burn-through and hydrogen cracking against a flowing fluid that pulls heat away fast, and a written plan that covers the fluid, pressure, temperature and flow rate.

Not every line qualifies. Some services and conditions, such as certain hydrogen, caustic or oxygen-enriched lines, or a wall too thin for the heat input, rule out welding in service, and the plan then moves to a line stop and bypass or to a planned outage. At refineries the decision runs through Part B's management of change and hot work controls. Paul Industries surveys, plans, welds, tests the fitting, and taps the line, returning the thickness readings, procedure and test records with the job.

Tank and terminal welding in Washington

Tank and terminal welding in Washington follows API 653 for repairs and alterations to welded storage tanks, and at Ecology-regulated Class 1 facilities it now includes seismic retrofits, because Ecology gave existing tanks there a deadline for seismic protection measures, a decade from the 2023 amendment or the next scheduled internal API 653 inspection if that comes later. Retrofits mean welding anchor chairs to the shell, reinforcing nozzle areas, and installing flexible connections between tank and piping, all designed and documented for the facility's spill risk analysis.

Other common tank welds are bottom replacements and patch plates after underside corrosion, shell inserts, new nozzles for process changes and floating roof repairs. Each tank job starts with cleaning, gas-freeing and entry permits, and ends with examination, testing and a repair record. Paul Industries welds tank repairs and builds new tanks through tank fabrication in Washington.

Welding through Washington weather on both sides of the Cascades

Field welding in Washington has to manage two different climates: wet, windy marine weather west of the Cascades and cold winters with hot, dry summers to the east. AWS D1.1 sets a minimum ambient temperature for structural welding and requires wind protection for gas-shielded processes, and ASME and AWS procedures both require dry, clean surfaces and the preheat their qualification records specify, so weather is a quality item, not just a comfort item.

How Washington weather shapes field welding controls
ConditionWhere in WashingtonEffect on weldingControl used
Rain and wet steelPuget Sound, Olympic Peninsula, coastMoisture causes porosity and hydrogen in the weldShelters, drying with heat, low-hydrogen consumables stored in ovens
Wind at the arcWaterfront terminals, Columbia Gorge, open eastern sitesLoss of gas shielding on GTAW and GMAWWind screens, enclosures, self-shielded processes where qualified
Winter coldSpokane, Columbia Basin, Yakima, WenatcheeFast cooling raises cracking risk in thick or hardenable steelPreheat and interpass control, heated enclosures, slow cooling
Summer heatTri-Cities and the Columbia BasinInterpass temperatures run high on stainless and alloy weldsInterpass monitoring, scheduling heavy welding for cooler hours

Material choice adds to the weather plan. Low-hydrogen processes and consumables, stored and handled to keep moisture out, are the default for structural and pressure work in wet weather; stainless and nickel alloys need interpass limits that a hot eastern afternoon can push past, so heavy alloy welding is scheduled for cooler hours or the joint is allowed to cool between passes with the temperature recorded. Post-weld heat treatment outdoors in winter needs insulated blankets and controlled heating rates, because a cold wind can pull a joint below its holding temperature.

Paul Industries plans the weather controls with the weld procedures: enclosures and heaters on the job schedule for winter work east of the mountains, and covered work areas and wind screens on wet western sites, so the procedure's requirements are met in the field rather than assumed.

Where industrial welding is needed across Washington

Industrial welding across Washington follows the state's industrial map: refineries and terminals on Puget Sound, aerospace manufacturing around Everett and Renton, where Boeing began 777-8 Freighter wing spar production in April 2026, biotech sites around Seattle, Bothell and Redmond, food processing in the Columbia Basin and central valleys, the Hanford site, whose waste vitrification plant began operating in October 2025, and manufacturing, hospital and campus work in Spokane, Tacoma and Vancouver.

Industrial welding by Washington region
RegionMain industriesTypical weldingRule or condition to plan for
Seattle and King CountyBiotech, hospitals, campuses, manufacturingOrbital sanitary welding, steam and condensate repairs, structural supportsSeattle welder approval under Director's Rule 15-2015; city boiler program
Everett, Renton and Snohomish CountyAerospace, biotech, manufacturingUtility piping, autoclave connections, equipment supportsHot work inside occupied production buildings
Plant welding, Tacoma, WA and Pierce CountyRefinery, port terminals, manufacturingPipe, tank and structural repairs during outagesPart B refinery reviews; Ecology terminal tank rules; wind and rain on the waterfront
Anacortes and Whatcom CountyRefineries and marine terminalsAlloy pipe welding, vessel and tank repairs, turnaround workPart B hot work, damage mechanism and startup reviews
Columbia Basin, Tri-Cities, Yakima and WenatcheeFood processing, cold storage, wine and fruit, HanfordAmmonia piping, stainless product lines, equipment repairsWork between production runs; winter preheat and summer interpass control
Industrial welding, Spokane, WA and the Inland NorthwestManufacturing, hospitals, campuses, foodPipe welding, structural repairs, boiler and vessel repairsHeated enclosures and preheat for winter field work

The work changes by setting. Refinery and terminal welding is code-heavy and record-heavy; aerospace and manufacturing plants need utility piping, equipment supports and repair welding inside busy production buildings; food plants need sanitary stainless welding and repairs planned between production runs; and campuses and hospitals need steam, condensate and heating water repairs scheduled around occupants. Paul Industries plans each job around those conditions, with the qualified procedures and records the setting requires.

What do industrial welding services in Washington cost?

Industrial welding services in Washington are priced by scope, and the cost drivers are the code and examination required, material and thickness, the number and position of welds, preheat and post-weld heat treatment, access and hot work controls inside operating areas, weather protection, and the documentation each code and owner requires. A day of maintenance welding on supports and frames costs far less per weld than a refinery alloy repair with PMI, hardness testing and full radiography.

Washington adds a few specific lines: the R program filing for boiler and vessel repairs, special inspection coordination for structural welds, Seattle's welder approvals inside the city, and refinery documentation for Part B reviews. Paul Industries prices welding as a lump sum for defined scopes and as unit or time-based rates for open maintenance work, with examination, heat treatment and records shown separately.

Who provides industrial welding services in Washington?

Paul Industries provides industrial welding services in Washington, welding pipe, structural steel, boilers, pressure vessels, tanks and equipment for refineries, terminals, food plants, aerospace and biotech manufacturers, hospitals, campuses and utilities, with qualified procedures, qualified welders, examination and complete weld records. Owners choose supply-only delivery of welded assemblies and spools, design-build of welded systems, or complete field installation and repair. Paul Industries runs its welding work from headquarters at 256 Shore Drive in Kilmarnock, Virginia; the company was formerly based in northern New Jersey, then Pennsylvania, and as an East Coast contractor it welds across Washington, in each of the 50 states and on international projects.

The same service in the headquarters state is described on industrial welding services in Virginia, and Gulf Coast refinery and terminal welding on industrial welding services in Texas. Welded work in Washington often runs alongside new piping, vessels and tanks from the related Washington pages linked above.

Industrial welding from Paul Industries in Washington

Paul Industries welds, repairs, fabricates and installs at Washington plants on Puget Sound, along the Columbia River, through the central valleys and in the Inland Northwest, with every weld documented to the code and the Washington rule behind it. Send drawings or a description of the work, the materials and codes, the site and its hot work and access rules, and the schedule window. Call 201-450-8280 or request a quote. More Paul Industries services in the state are gathered on the Washington hub, with Pacific region work on the West Coast page.

Standards referenced: ASME BPVC Section IX · ASME B31.1 · ASME B31.3 · ASME BPE · AWS D1.1 · AWS D1.6 · API 1104 · API 510 · API 570 · API 653 · National Board Inspection Code Part 3 · Chapter 296-24 WAC Part I (welding, cutting and brazing) · Chapter 296-104 WAC · Chapter 296-67 WAC Part B · International Building Code chapter 17 as adopted in Washington · Seattle Director's Rule 15-2015 · IIAR 2

Frequently asked questions

Who handles industrial welding Spokane, WA manufacturers and food plants need?

Paul Industries handles industrial welding in Spokane, Spokane Valley and across the Inland Northwest for manufacturers, food plants, hospitals and campuses: pipe welding, structural repairs, equipment frames and boiler and vessel repairs. Winter work there runs with preheat, heated enclosures and interpass control written into the procedures. Structural welds follow the building official's welder qualification and special inspection requirements.

Who provides plant welding Tacoma, WA port and industrial sites schedule during outages?

Paul Industries provides plant welding in Tacoma and Pierce County for refinery, port, terminal and manufacturing sites, from pipe and tank repairs to structural and equipment welding, scheduled into outages and turnarounds. Waterfront work gets wind and rain protection for gas-shielded processes. Every weld comes back with procedure, welder and examination records indexed for the owner's files.

Which welding services Seattle biotech and campus sites order most?

Seattle biotech and campus sites most often order orbital welding of sanitary tubing for purified water, clean steam and process lines, steam and condensate pipe repairs, and structural welding for equipment supports and platforms. Inside Seattle, structural welders need approval under Director's Rule 15-2015. Paul Industries performs industrial welding Seattle sites need with weld logs, borescope records and special inspection coordination.

Does Paul Industries weld at Everett and Renton aerospace plants?

Yes. Paul Industries welds at aerospace manufacturing plants in Everett, Renton and across Snohomish and King counties, covering compressed air, nitrogen, steam and cooling water piping, autoclave and curing system connections, equipment supports and repair welding on production equipment. Work inside occupied production buildings runs under hot work permits with fire watch and shielding planned before each shift.

Is there a Washington State welding certification for structural work?

Washington State welding certification for structural work comes through the Washington Association of Building Officials welder certification program, which building departments use to confirm welder qualification, with tests based on AWS standards. Seattle approves structural steel welders on city-permitted projects under Director's Rule 15-2015. The state does not issue an individual welder license, though every contractor must register with L&I.

How do welding companies in Washington State document welder qualifications?

Welding companies in Washington State document qualifications with procedure qualification records and welding procedure specifications for each code, welder performance qualification records, continuity logs showing each welder has used the process within the code's limit, and structural welder cards accepted by the building official. Paul Industries keeps these records current and supplies them with each job package.

When does structural welding in Washington need special inspection?

Structural steel welding on permitted work in Washington needs special inspection under chapter 17 of the building code as the state adopts it, performed by an approved agency for the owner, with inspection tasks before, during and after welding set by the referenced steel quality assurance provisions and the weld type. Paul Industries sets hold points with the special inspector and turns over weld maps and reports.

Which Washington rules apply to hot work inside an operating plant?

Hot work inside an operating Washington plant follows Part I of chapter 296-24 WAC, which covers fire prevention, welding or cutting of containers, confined spaces, ventilation and protection of employees, along with the fire code's hot work chapter and the plant's own permit system. Refineries add the hot work section of Part B of chapter 296-67 WAC. Paul Industries plans gas testing, fire watch and isolation for each location.

How are boiler and pressure vessel weld repairs filed in Washington?

A weld repair on a Washington boiler or pressure vessel is filed after the work: the R-1 or R-2 report and the signed job checklist go to the jurisdiction no later than 45 days after the physical work ends. Before welding, the repair plan goes to the Authorized Inspector under the NBIC Part 3 rules. Paul Industries assembles that package as the repair proceeds.

What changes for welding at a Washington refinery since Part B took effect?

Since Part B took effect on December 27, 2024, welding at Washington refineries runs under a refinery-specific hot work section, management of change for anything beyond replacement in kind, damage mechanism reviews that set materials and examination, and a pre-startup safety review after every turnaround. Paul Industries welds to the resulting specifications and returns hardness, PMI and examination records by line.

Which welds does an Ecology seismic retrofit add to a terminal tank?

An Ecology seismic retrofit on an existing terminal tank usually adds anchor chairs welded to the shell, reinforcement at shell nozzles, and flexible connections between the tank and its piping, designed so the tank can move in an earthquake without tearing a connection. API 653 governs the welding and examination. Paul Industries designs, welds and documents the retrofit for the facility's spill risk analysis.

How is field welding protected from rain on western Washington job sites?

Field welding on wet western Washington sites is protected with shelters or enclosures over the joint, heat to dry the steel before welding, low-hydrogen electrodes kept in heated ovens, and wind screens for gas-shielded processes. Wet steel and damp consumables cause porosity and hydrogen cracking, so these controls are part of meeting the procedure. Paul Industries builds them into the job schedule.

What preheat does winter welding need in eastern Washington?

Winter welding in eastern Washington needs the preheat and interpass temperatures in the qualified procedure, which rise with steel thickness, carbon equivalent and restraint, and the code's minimum ambient limits apply as well. Heated enclosures and slow cooling help thick or hardenable sections. Paul Industries measures and records preheat at each joint so the record shows the procedure was met.

Can Paul Industries repair conveyor frames and equipment at a Columbia Basin food plant between runs?

Yes. Paul Industries repairs conveyor frames, equipment bases, platforms, guards and stainless product contact parts at Columbia Basin food plants in Moses Lake, Othello, Quincy and Pasco, scheduled between production runs or during the off-season. Stainless welds in product zones are ground smooth and passivated so they clean in place like the original equipment.

Can welded assemblies be supplied for a Washington plant to install?

Yes. Paul Industries supplies welded assemblies, pipe spools, supports and frames to Washington plants as a supply-only scope, with weld maps, procedure and welder records, examination reports and material certifications. Assemblies are fabricated off site under controlled conditions and shipped ready for installation, which keeps field welding inside the plant to the tie-in welds.

What should be sent to get a welding quote for a Washington plant?

Send drawings, sketches or photographs of the work, the materials and thickness, the code and examination required, the site and its hot work, access and safety rules, whether the job is inside Seattle, and the schedule window. For boiler and vessel repairs, include the nameplate and inspection report. Paul Industries replies with a welding plan, schedule and price.

Need code welding at a Washington plant, refinery or terminal?

Send drawings or photos of the work, the materials and code, the site's hot work rules and the schedule window. Call 201-450-8280 or request a quote.