Paul Industries provides pressure vessel fabrication in Ohio, designing, building, testing and installing ASME Section VIII vessels for refineries, chemical plants, pharmaceutical and biotech sites, food and beverage plants and plant utilities. Ohio requires every unfired vessel within the code to be inspected while it is built and again on completion, and to have its inspector-signed data report on file with the state before it holds pressure. Paul Industries plans each vessel around that requirement from the first data sheet, so the documentation arrives with the steel.

Request a quote or call 201-450-8280

Headquarters 256 Shore Drive, Kilmarnock, Virginia
State statute Ohio Revised Code 4104.10
Construction code ASME Section VIII, 2023 edition (OAC 4101:4-3-01)
Before operation Inspector-signed data report filed with the superintendent
Registration National Board registration for every code vessel
Special designs Ohio Special approval from the Board of Building Standards
Reviewed November 2026

What is pressure vessel fabrication in Ohio under Chapter 4104?

Pressure vessel fabrication in Ohio is the design, construction, inspection and testing of containers that hold internal or external pressure, which Revised Code 4104.01 defines broadly to include pressure from an outside source and pressure produced by direct or indirect heat. Reactors, columns, separators, receivers, accumulators, filter housings, heat exchanger shells, autoclaves and jacketed process tanks all meet that definition when they operate within the code’s scope.

The statute itself is short on the subject and leans on the board. Revised Code 4104.10 says that unfired vessels must be thoroughly inspected during fabrication and upon completion, that no vessel is operated until a copy of the manufacturer’s data report, signed by the inspector, is filed with the Superintendent of Industrial Compliance, and that every vessel conforms in every detail to the board’s rules. Revised Code 4104.20 then forbids an owner to operate a vessel in violation of that section. The practical effect is that paperwork filed in Columbus is a condition of startup.

The Ohio boiler and pressure vessel rules a fabricator works to

The Ohio boiler and pressure vessel rules sit in Administrative Code Chapters 4101:4-1 through 4101:4-10, written by the Board of Building Standards and in their current form since July 1, 2024. Rule 4101:4-3-01 adopts the 2023 ASME Boiler and Pressure Vessel Code, including Section VIII Divisions 1, 2 and 3 for vessels, Section II for materials, Section V for examination, Section IX for welding and Section X for fiber-reinforced plastic vessels, together with the 2023 code cases and the 2023 National Board Inspection Code. People who search for the Ohio boiler and pressure vessel code are looking for this set: a state chapter that points to ASME and the National Board by edition.

Rule 4101:4-6-01 then lays out the build in four requirements. Each vessel is constructed and tested to the applicable ASME section. An authorized inspector inspects it during construction and after completion. Once the manufacturer’s data report is completed and accepted by the inspector, the ASME certification mark and required markings go on the vessel. Every vessel is registered with the National Board, with the original data report filed there for permanent retention and the registration number applied to the vessel.

What is considered a pressure vessel, and which fall outside the Ohio pressure vessel code?

What is considered a pressure vessel in Ohio follows both the statute’s broad definition and the ASME scope, because Rule 4101:4-2-01 excludes any vessel beyond the reach of the applicable ASME section. Section VIII Division 1 does not cover vessels whose operating pressure stays at or below 15 psi, or vessels with an inside diameter of 6 inches or less, so an atmospheric storage tank, a low pressure surge drum and a small-diameter filter housing usually sit outside the Ohio pressure vessel code even though they hold fluid.

The statute adds categorical exclusions. Revised Code 4104.04 leaves out vessels under federal control or inspection, air tanks on vehicles operating under other state authorities, air tanks on railroad rights of way used to run trains, and vessels regulated by the State Fire Marshal under Chapter 3737. A second group, including portable vessels used on farms for agriculture and water pressure tanks in private residences and apartment houses of fewer than six units, is built to the board’s construction rules but is spared the state inspection and certificate steps.

What is an example of a pressure vessel in each Ohio industry
IndustryTypical vesselsUsual code route
Petroleum refiningSeparators, accumulators, reactors, knockout drumsSection VIII Division 1 or 2, PSM mechanical integrity
Chemicals and polymersReactors, strippers, receivers, jacketed vesselsSection VIII Division 1, often alloy or clad construction
Biologics and gene therapyBioreactor and media vessels, buffer tanks, clean steam separatorsSection VIII Division 1 with ASME BPE finishes
SemiconductorBulk gas buffers, chemical delivery vessels, vacuum chambersSection VIII Division 1 with high purity finishes
Food and beverageCarbon dioxide receivers, retorts, cookers, deaeratorsSection VIII Division 1, 3-A sanitary where product contacts
Plant utilitiesAir receivers, blowdown tanks, expansion tanks, condensate receiversSection VIII Division 1; blowdown tanks to NB-27 guidance

Ohio pressure vessel registration: data reports, National Board numbers and Ohio Specials

Ohio pressure vessel registration runs through the National Board rather than through a separate state number for each standard vessel: Rule 4101:4-6-01 requires every code vessel to be registered with the National Board and to carry its registration number, and Revised Code 4104.10 requires a copy of the inspector-signed data report on file with the superintendent before the vessel operates. Owners therefore hold two records for each vessel, the National Board registration and the state’s copy of the data report.

Vessels whose design departs from ASME take a different path. Rule 4101:4-5-01 allows an application to the Board of Building Standards for legal use of a special design in Ohio, made before fabrication with documents sealed by a registered professional engineer: a written analysis of how the design departs from the ASME code, construction drawings, material specifications, design calculations, welding details and procedures, and quality control procedures. A professional engineer assigned or approved by the board reviews the package. If the board approves, an authorized inspector inspects the vessel during construction and a general inspector tags it with an OHIO SPECIAL serial number. Any later alteration of an Ohio Special goes back to the board first.

Inspection during construction is also available directly from the state. Revised Code 4104.18 sets the fee for a general inspector’s complete inspection during construction at $35 per hour for vessels made in Ohio, with manufacturers elsewhere able to apply for the same service.

Ohio pressure vessel inspection requirements after the vessel is in service

Ohio pressure vessel inspection requirements after installation come from three places: the board’s rules on maintenance and repair, the in-service inspection authority the superintendent’s inspectors hold, and the owner’s own mechanical integrity program. Rule 4101:4-9-01 makes the owner responsible for keeping vessels, controls, devices and safeguards safe, in good working order and free of leaks and defects, and requires an illegible or lost nameplate to be replaced under the NBIC. The fixed calendar intervals in Revised Code 4104.11 are written for boilers.

For plants that handle highly hazardous chemicals, OSHA’s process safety management standard, 29 CFR 1910.119, requires pressure vessels in covered processes to be inspected and tested to recognized and generally accepted good engineering practice, and refiners and chemical producers in Ohio generally apply API 510 to set those intervals. Under API 510, external inspections occur at least every five years or at the internal interval if that is shorter, and internal or on-stream inspections at the lesser of ten years or half the remaining corrosion life. Plants operating a National Board accredited owner-user inspection organization, which Rule 4101:4-3-01 recognizes through NB-371, run those inspections themselves.

How often do pressure vessels need to be inspected in Ohio service
SituationGoverning requirementTypical practice
New vessel before startupORC 4104.10: inspection in fabrication and on completion; data report filedAuthorized inspector signs the data report; copy goes to the superintendent
Vessel in a PSM-covered process29 CFR 1910.119 mechanical integrityAPI 510 intervals: external at five years or less, internal at ten years or half remaining life
Vessel at a general manufacturing plantOAC 4101:4-9-01 owner maintenance dutyInsurer inspections and the plant’s own program, often modeled on API 510
After a repairOAC 4101:4-9-01(H) and NBIC Part 3Inspector approval, signed repair report filed with the superintendent
After an alteration or rerateNBIC Part 3 under the R programAuthorized inspector approves before work; new nameplate data

ASME pressure vessel requirements in the 2023 code Ohio adopted

ASME pressure vessel requirements in the 2023 Section VIII that Ohio adopted start with design conditions: internal and external design pressure, design temperature, minimum design metal temperature, corrosion allowance and the loadings from wind, seismic forces, piping and supports. From those, the designer selects materials listed in Section II, calculates thicknesses for shells, heads, nozzles and reinforcement, and sets the joint efficiencies that the chosen radiography or ultrasonic examination supports.

Ohio winters make minimum design metal temperature a real decision for outdoor vessels. Section VIII’s impact test exemption curves tie the minimum permissible temperature to the material group and thickness, so a carbon steel separator or receiver sited outdoors in Northwest or Northeast Ohio is checked against the coldest metal temperature it can reach, including during depressurization, and specified with impact tested or fine grain material where the curves require it. Paul Industries confirms that value with the owner before plate is ordered, because changing it later means new material.

Relief protection completes the design. Rule 4101:4-4-03 requires the safety devices that keep pressure and temperature within design limits to be installed and tested under the ASME code and the NBIC, and requires relief discharges to be routed where they endanger no one. Relief valves are sized for every credible overpressure case, from blocked outlets to external fire, and their set pressures and capacities are recorded in the vessel file.

Which section of ASME deals with construction of pressure vessels?

Section VIII of the ASME code governs pressure vessel construction, divided into three divisions. Division 1 covers the large majority of plant vessels with design-by-rule formulas. Division 2 uses higher allowable stresses with more rigorous design analysis and examination, which saves weight on thick, high pressure vessels. Division 3 covers very high pressures. Section X covers fiber-reinforced plastic vessels used in corrosive service.

From data sheet to hydrotest: the build sequence for an Ohio vessel

The build sequence for an Ohio vessel runs from the process data sheet through design, material procurement, forming, welding, examination, heat treatment where required, the pressure test and final documentation, with the authorized inspector holding points at each critical stage. Paul Industries prepares the design calculations and drawings, issues them for the owner’s review, and freezes the design before material is ordered.

Plate and pipe are checked against their mill test reports and marked for traceability. Shells are rolled and heads formed, nozzles and reinforcing pads cut and fitted, and every pressure weld is made to a procedure and by a welder qualified under ASME Section IX. Radiographic or ultrasonic examination follows the joint efficiency chosen in design, and postweld heat treatment is applied where thickness or service requires it. The hydrostatic or pneumatic test is witnessed by the inspector, who then signs the data report.

Buyers comparing pressure vessel manufacturers, Ohio projects in mind, look for that sequence in the quotation, and Paul Industries lays it out with inspection hold points named. Plant engineers screening ASME pressure vessel manufacturers also ask for sample data reports, weld maps and examination plans, and Paul Industries supplies them with the proposal. Where the design calls for heat transfer surfaces, the shell and tube work is covered on the heat exchangers page, and the test procedures behind the final pressure test are described on hydrostatic testing.

Pressure vessels in Ohio’s refining, chemical and life sciences plants

Ohio’s demand for pressure vessels comes from four refineries, a large chemical and polymer base, a growing biologics and pharmaceutical cluster around Columbus, and the semiconductor fab under construction in New Albany. Each sector asks for different materials, finishes and documentation, and the same Ohio filing requirement applies to all of them.

The Energy Information Administration lists Ohio refineries in Lima, Toledo and Canton with combined crude capacity of more than 600,000 barrels per calendar day as of January 1, 2026, and their separators, drums and reactors are replaced and added during turnarounds. In Lima, INEOS Nitriles produces acrylonitrile, acetonitrile and hydrogen cyanide, services that call for careful material selection. In Central Ohio, Amgen’s New Albany biomanufacturing site announced a $900 million expansion in April 2025, Andelyn Biosciences runs 16 modular cGMP suites at its Columbus headquarters, and Hikma committed $51 million in June 2026 to sterile injectable capacity in Bedford. Intel’s Ohio One site in New Albany, where the first fab’s construction is now targeted for completion in 2030, will need bulk gas and chemical delivery vessels built to semiconductor purity standards.

A pressure vessel Ohio biologics plants specify usually carries ASME BPE surface finish requirements, electropolished product contact surfaces, drainable geometry and passivation after fabrication, which is covered on passivation services in Ohio. Refinery and chemical vessels emphasize corrosion allowance, cladding or alloy selection, and examination coverage. Both share the same Section VIII design and Ohio filing steps.

Repairs, alterations and rerates on vessels in Ohio service

Repairs, alterations and rerates on vessels in Ohio service follow Part 3 of the National Board Inspection Code under Rule 4101:4-9-01, and the path depends on whether the work runs under the R program. Without an R Certificate of Authorization, the owner or the repairer notifies the Division of Industrial Compliance ahead of any repair to an existing ASME vessel, the repair needs the approval of a general or special inspector, and that inspector’s signed report goes to the superintendent’s file. A vessel alteration or rerate proceeds under an R Certificate of Authorization, with the authorized inspector agreeing to the plan before the first cut.

Older equipment raises a further question. Non ASME pressure vessels, and vessels without an Ohio number, are evaluated by the superintendent before a major repair or alteration and must meet the applicable ASME code or be retired from use. Rerates usually rest on a fresh thickness survey, a recalculation under the current edition and, where needed, a new pressure test, with the nameplate updated to the new rating. Paul Industries performs the thickness survey, prepares the calculations, carries out the welded repair or alteration and coordinates the inspector’s witness points, with the welding described on industrial welding services in Ohio.

Jacketed, clad and lined vessels for Ohio process plants

Jacketed, clad and lined vessels make up a large share of Ohio process work, because chemical, polymer, food and pharmaceutical plants heat and cool batches through the vessel wall and protect the wall from aggressive contents. Each construction adds its own Section VIII checks to the design and its own steps to the build.

A jacketed vessel is two pressure chambers in one: the inner shell sees process pressure on one side and jacket pressure or vacuum on the other, and the jacket itself is designed as a separate chamber with its own relief protection. Conventional full jackets, dimple jackets and half-pipe coils each suit different heating media, from tempered water and glycol to steam and hot oil. The inner shell is checked for external pressure during jacket service and for vacuum during cleaning or emptying, which often governs its thickness more than internal pressure does.

Clad plate, with a thin alloy layer metallurgically joined to a carbon steel backing, gives corrosion resistance at a fraction of the cost of solid alloy on thick vessels, and is common in refinery and chemical service. Welding clad plate means restoring the cladding over every seam with overlay of the right chemistry and examining it. Linings such as glass, rubber or fluoropolymer go into vessels where no economical metal resists the contents, and the vessel design accounts for the lining’s temperature and vacuum limits. Paul Industries designs the jacket, cladding or lining together with the shell, so the data report reflects the complete vessel the plant will run.

What drives the price of pressure vessel fabrication in Ohio?

The price of pressure vessel fabrication in Ohio is driven by material, thickness, size, internals, examination and documentation more than by any state fee. Stainless steels, duplex grades and nickel alloys multiply material cost over carbon steel, and electropolished BPE finishes add labor to every product contact surface. Thicker shells bring postweld heat treatment and longer welding time. Full radiography, impact testing, positive material identification and extensive documentation packages each add a measurable step.

Cost drivers on an Ohio pressure vessel and what to send for a firm price
DriverEffect on priceWhat to send
MaterialAlloy and clad construction multiply material costProcess fluid, contaminants and design life
Design pressure and temperatureSet thickness, heat treatment and test pressureOperating and upset conditions, relief set point
Minimum design metal temperatureCan require impact testing or different plateIndoor or outdoor siting and depressurization cases
Internals and nozzlesTrays, packing, baffles and jackets add hoursNozzle schedule and internals sketch
Finish and cleanlinessBPE and high purity finishes add polishing and testingSurface finish and passivation requirements
DocumentationTurnover packages and owner specifications add effortThe owner’s vessel specification and turnover list

Paul Industries returns a budget figure from a process data sheet and comparable vessels, then a firm price once the design conditions, materials and documentation requirements are fixed.

Who fabricates pressure vessels in Ohio?

Paul Industries fabricates pressure vessels for Ohio refineries, chemical plants, pharmaceutical and biotech sites, semiconductor projects, food and beverage plants and plant utility systems, from Toledo and Lima to Columbus, Cincinnati, Dayton, Cleveland and Akron. Paul Industries is headquartered at 256 Shore Drive in Kilmarnock, Virginia, after earlier years in northern New Jersey and then Pennsylvania, and takes vessel work across Ohio, the Midwest and every other state.

The work spans the full route: design to Section VIII, fabrication, examination, heat treatment, pressure testing and the data report the Ohio filing needs, followed by delivery, setting, connection and startup at the plant. Owners choose supply-only, design-build or complete installation. Vessels that sit beside atmospheric storage are covered with tank fabrication in Ohio, the piping around them on process piping in Ohio, and qualification of vessels in GMP service on validation and commissioning in Ohio. Steam generating equipment in the same plant is covered on boiler repair in Ohio.

The approach in the headquarters state is described on pressure vessel fabrication in Virginia, and a contrasting state program on pressure vessel fabrication in New York. The national scope is on the pressure vessel fabrication service page, and the state overview on the Ohio page.

Pressure vessels from Paul Industries for Ohio plants

Paul Industries designs and builds Ohio vessels with the state’s startup condition in view: an authorized inspector at every hold point, a signed data report, National Board registration, and a copy of the data report ready for the superintendent before the vessel is pressurized. Repairs and rerates are carried through NBIC Part 3 with the inspector’s approval recorded. To start, send the process data sheet, design conditions, nozzle schedule and any owner vessel specification, and request a quote.

Standards referenced: Ohio Revised Code Chapter 4104, sections 4104.01, 4104.02, 4104.04, 4104.10 and 4104.20 · Ohio Administrative Code Chapters 4101:4-1 to 4101:4-10 (Board of Building Standards boiler and pressure vessel rules) · ASME Boiler and Pressure Vessel Code, 2023 edition, Section VIII Divisions 1, 2 and 3 · ASME Section II (materials), Section V (nondestructive examination), Section IX (welding) and Section X (fiber-reinforced plastic vessels) · National Board Inspection Code (NBIC), 2023 edition, Part 3 · ASME BPE · API 510 · OSHA 29 CFR 1910.119

Frequently asked questions

Who builds reactors and separators for refineries and chemical plants in Toledo and Lima?

Paul Industries builds reactors, separators, drums and receivers for refineries and chemical producers in Toledo, Lima and the rest of Northwest Ohio. Vessels for those plants are usually timed to a turnaround, so Paul Industries fixes the design and orders material early, completes fabrication and the witnessed pressure test before the unit comes down, and has the data report ready for the Ohio filing before startup.

Does Paul Industries supply stainless process vessels to biologics sites in Columbus and New Albany?

Paul Industries supplies stainless process vessels, buffer and media tanks and clean steam separators to biologics, gene therapy and pharmaceutical plants in Columbus, New Albany and Licking County. Those vessels combine Section VIII construction with ASME BPE finishes, drainability and passivation, and Paul Industries delivers the turnover package the site’s qualification team needs along with the code documentation.

Who fabricates pressure vessels for plants in Cleveland, Akron and Youngstown?

Paul Industries fabricates and installs pressure vessels for polymer, chemical, metals and utility applications in Cleveland, Akron, Canton, Youngstown and the rest of Northeast Ohio. Outdoor vessels in that region are checked against Lake Erie winter temperatures when the minimum design metal temperature is set, and replacements for older vessels are built to the 2023 Section VIII edition Ohio has adopted.

Who approves pressure vessels in the US, and who in Ohio?

In the US, construction approval rests on the ASME code and an authorized inspector who witnesses the build and signs the data report, with the National Board registering the vessel. States then decide what they require for installation and operation. In Ohio, Revised Code 4104.10 adds that the inspector-signed data report must be filed with the Superintendent of Industrial Compliance before the vessel operates.

Is ASME mandatory for a pressure vessel installed in Ohio?

Yes, for vessels within the code’s scope. Rule 4101:4-6-01 requires every boiler and pressure vessel not otherwise exempt to be constructed and tested to the applicable section of the ASME code and registered with the National Board. The alternative is a special design approved by the Board of Building Standards as an Ohio Special, which still requires inspection during construction and a state serial number.

Why are pressure vessels round rather than square?

Pressure vessels are cylindrical or spherical because curved shells carry internal pressure as nearly uniform membrane stress, while flat sides and corners bend and concentrate stress. A cylinder with formed heads holds a given pressure with far thinner walls than a box of the same volume. Flat surfaces appear in pressure equipment where they are needed, such as some heat exchanger channel covers, and are made much thicker or stayed.

What happens when a used vessel is installed at a new Ohio site?

A used vessel moved to a new Ohio site needs its ASME data report, nameplate and National Board registration intact, a current condition assessment, and its design conditions checked against the new service. Vessels without an ASME stamp or Ohio number go to the superintendent for evaluation under Rule 4101:4-9-01 and must meet the ASME code or be retired. Paul Industries performs the assessment and any rerate before reinstallation.

What does an Ohio Special approval require before fabrication starts?

An Ohio Special approval requires an application to the Board of Building Standards, made before fabrication, with documents sealed by a registered professional engineer: an analysis of where the design departs from ASME, construction drawings, material specifications, design calculations, welding details and procedures, and quality control procedures. After the board approves, an authorized inspector inspects construction and a general inspector applies the OHIO SPECIAL serial number.

Does a pressure vessel need a state permit before installation in Ohio?

Ohio’s installation permit under Rule 4101:4-7-01 is written for boilers. For a pressure vessel, the state’s precondition is the filing: a copy of the manufacturer’s data report, signed by the inspector, on file with the superintendent before the vessel operates. The building around it still follows the Ohio Building and Mechanical Codes, and Paul Industries confirms any municipal permit needed for the foundation, structure or connected systems.

Which vessels need an owner-user inspection program in Ohio?

Vessels in processes covered by OSHA’s process safety management standard need a written mechanical integrity program with inspections and tests to recognized practice, which in refining and chemicals usually means API 510. Plants with a National Board accredited owner-user inspection organization, recognized in Ohio’s rules through NB-371, conduct those inspections with their own qualified inspectors. Other plants rely on insurer inspections and their maintenance programs.

Does Paul Industries rerate vessels for higher pressure at Ohio plants?

Paul Industries rerates vessels at Ohio plants when thickness, material and design margins support the new conditions. The work starts with a thickness survey and a recalculation under the current Section VIII edition, proceeds under an R Certificate of Authorization once the authorized inspector has accepted the plan, and ends with any required pressure test and an updated nameplate. Ohio Special vessels go back to the Board of Building Standards first.

What materials suit vessels in acrylonitrile and other nitrile service in Lima?

Vessels in acrylonitrile, acetonitrile and hydrogen cyanide service are usually carbon steel or stainless depending on temperature, water content and contaminants, with stainless grades chosen where corrosion or product purity demands. Paul Industries confirms the owner’s material specification and corrosion data, then selects plate, forgings, gaskets and weld consumables to match, with positive material identification on alloy components.

How long does an ASME vessel take to build for an Ohio project?

An ASME vessel for an Ohio project takes from several weeks for a small carbon steel receiver to many months for a large alloy reactor, with material lead time usually the longest step. Design approval, heat treatment, examination and documentation reviews add time. Paul Industries sets the schedule once the data sheet and materials are confirmed and tracks it against the plant’s installation date.

Do semiconductor bulk gas vessels for New Albany need anything beyond Section VIII?

Semiconductor bulk gas and chemical delivery vessels need Section VIII construction plus the cleanliness, surface finish, leak tightness and material traceability that fab owners specify, often drawing on SEMI standards for high purity gas and chemical systems. Paul Industries builds to the owner’s specification, records the cleaning and leak test results, and seals the vessel for delivery so the purity achieved at fabrication survives to installation.

How are vessels delivered and set at an operating Ohio plant?

Vessels are delivered on schedules agreed with the plant, rigged and set on prepared foundations or supports, leveled and anchored, then connected to piping, instruments and relief systems. Large vessels are often set during a turnaround window with crane access planned in advance. Paul Industries plans the lift, the route through the plant and the hot work permits so the setting fits inside the outage.

What does the turnover package for an Ohio vessel contain?

The turnover package for an Ohio vessel contains the inspector-signed manufacturer’s data report, the National Board registration, design calculations and drawings, material test reports, weld procedures and welder qualifications, examination and heat treatment records, the pressure test record and relief device data. Life sciences vessels add surface finish, passivation and cleaning records. A copy of the data report goes to the superintendent before startup.

Which documents let Paul Industries price an Ohio pressure vessel?

Paul Industries prices an Ohio pressure vessel from the process data sheet with design pressure and temperature, the fluid and its contaminants, the minimum design metal temperature, a nozzle schedule, internals, finish requirements and the owner’s vessel specification. A sketch or an existing vessel’s data report speeds the work. The first answer is a budget range from comparable vessels, followed by a firm price once the design is fixed.

Specifying a code vessel for an Ohio plant?

Send the process data sheet, design conditions, nozzle schedule and any owner vessel specification. Call 201-450-8280 or request a quote.