Paul Industries designs, fabricates, installs, tests and repairs process piping in California for biotech and pharmaceutical plants, semiconductor fabs, food, dairy and wine processors, chemical plants, fuel terminals and refineries, building every line to ASME B31.3 and to the permit, inspection and test steps of Chapter 14 of the California Mechanical Code. California is one of the few states whose mechanical code carries a chapter of its own for process piping, and its plants add Cal/OSHA process safety rules, hazardous production material limits and seismic bracing on top. Paul Industries takes the whole scope, from the design package and spool fabrication to field installation, tie-ins, testing and the turnover file.

Request a quote or call 201-450-8280

Headquarters 256 Shore Drive, Kilmarnock, Virginia
Piping permit Required to install, alter or repair process piping (CMC 1402.1)
Final test Hydraulic at 1.5 times design pressure or pneumatic at 110%, 30 minutes (CMC 1405)
Refinery damage reviews Revalidated at least every five years (Title 8, 5189.1)
Building code 2025 California Building Code with ASCE 7-22, effective January 1, 2026
Reviewed November 2026

Process piping in California has a mechanical code chapter of its own

Process piping in California is governed by Chapter 14 of the California Mechanical Code, which covers process piping installed in or in conjunction with a building or structure, and which makes it unlawful to install, alter or repair process piping without a permit. The 2025 edition, based on the 2024 Uniform Mechanical Code, took effect on January 1, 2026 along with the rest of Title 24, and it points to ASME B31.3 for the piping itself.

The practical effect is that a California piping job has a building department in it from the start. Plans, calculations and diagrams go in with the permit application, a registered design professional prepares them where the department requires it, and the work is inspected twice before the line carries product. The national picture of materials, welding and spool fabrication is set out on the process piping page; this page covers what California adds.

How a California Mechanical Code Chapter 14 piping permit runs from application to final test
StepWhat the chapter requiresWhat Paul Industries prepares
Permit (1402)A permit before process piping is installed, altered or repaired, showing the outlets on each systemPermit drawings and the outlet count per system
Plans (1403)Plans, calculations and diagrams with the application; a registered design professional where the department asksIsometrics, line list, design conditions, support and seismic calculations
Workmanship (1404)Piping not strained or bent; tanks and equipment not hung on the pipingSupports and anchors sized so equipment nozzles carry no piping load
Rough inspection (1405.2.1)Size, material and installation checked before the piping is coveredMaterial certificates, weld maps and access before insulation or walls close
Final inspection and test (1405.2.2)Hydraulic test at 1.5 times maximum design operating pressure, or pneumatic at 110 percent, held 30 minutes with no perceptible dropTest procedure, calibrated gauges, test record signed by the inspector
Materials and joints (1406)Piping to ASME B31.3; welded supply lines for the most toxic hazardous production materialsMaterial and joint selection per fluid service, recorded in the line list

Process piping vs plumbing under California’s codes

Process piping vs plumbing in California comes down to what the pipe carries and which part of Title 24 governs it: water supply, drainage and fixtures belong to the California Plumbing Code, while lines carrying product, process chemicals, process gases and process utilities fall under Chapter 14 of the California Mechanical Code and ASME B31.3. Steam boiler piping follows the boiler code and ASME B31.1, and Cal/OSHA’s Pressure Vessel Unit applies the National Board Inspection Code to repairs on boiler piping.

The boundary matters for the permit, the inspector and the test. A purified water loop in a South San Francisco biotech building, for example, is process piping even though it carries water, because it feeds product and is built to ASME BPE and B31.3; the domestic water line beside it is plumbing. Paul Industries draws the boundary on the line list at the design stage, so each system is permitted, tested and documented under the right code. Boiler-side piping is covered with boiler repair in California.

Hazardous process piping in fabs and labs

Hazardous process piping in California semiconductor fabs and research labs follows three overlapping rules: the California Fire Code’s Chapter 27 for Group H-5 semiconductor fabrication facilities, the hazardous production material provisions of the California Building Code, and the hazardous process piping sections of Mechanical Code Chapter 14. Together they decide where supply lines may run, how they are joined and how a leak is contained.

Under Chapter 14, supply piping for hazardous production materials with a health hazard ranking of 3 or 4 is welded throughout unless it runs inside an exhausted enclosure. Hazardous process supply piping in service corridors stays exposed to view and identified by its contents, liquid lines carry a way to direct spills to containment or drainage, and supply piping is kept out of exit corridors, required fire-resistive egress and concealed spaces except under the specific allowances the code lists. Paul Industries routes fab and lab gas and chemical lines to those rules, with orbital welds, double containment where the design calls for it, leak detection tie-ins and the test records the fire marshal reviews. Ultrapure water supply for the same buildings is described on ultrapure water systems in California.

California process safety management and piping

California process safety management for piping comes from two Cal/OSHA sections: Title 8 section 5189 for general industry, and section 5189.1, in effect since October 1, 2017, for petroleum refineries. Section 5189 applies to processes holding a chemical at or above the Appendix A threshold, or 10,000 pounds or more of a Category 1 flammable gas or a flammable liquid with a flashpoint below 100 degrees Fahrenheit in one location; section 5189.1 replaces it at refineries and names piping as process equipment.

What Cal/OSHA process safety rules ask of piping work
ElementSection 5189 (general industry)Section 5189.1 (refineries)What it means for a piping job
Mechanical integrityInspections and tests to good engineering practice, with records naming date, inspector and equipmentInspections and tests to recognized and generally accepted good engineering practice (RAGAGEP), with the same recordsThickness readings, test records and weld documentation tied to line numbers
DeficienciesCorrected before further use, or safely and promptly with interim measuresRepairs consistent with RAGAGEP; corrective actions generally within 30 months, shutdown items at the first scheduled turnaroundRepairs planned into turnarounds with interim safeguards recorded
Management of changeWritten procedures for every change except replacement in kindCovers all changes except replacements in kind, and expressly includes temporary pipe repairsA clamp, sleeve or bypass goes through change review before it is fitted
Damage mechanism reviewNot a separate elementRequired for each process with a damage mechanism; revalidated at least every five years and reviewed before major changesMaterial selection checked against corrosion, cracking and thermal fatigue findings
Hierarchy of hazard controlsNot a separate elementInherent safety first, then passive, active and procedural safeguardsDesign changes that remove a hazard rank ahead of added devices
Pre-startup safety reviewRequired for new and modified facilitiesRequired for new and changed processes, shutdowns and all turnaround workPiping turned over with test, inspection and as-built records ready for the review

How often should pipes be inspected at a California refinery or chemical plant?

How often should pipes be inspected at a California refinery or chemical plant is set by the plant’s mechanical integrity program rather than a single number: section 5189 ties frequency to manufacturer recommendations and good engineering practice, section 5189.1 ties it to recognized engineering practice or a more protective internal practice, and both require more frequent inspection when operating experience shows it is needed. In practice that means a circuit-by-circuit schedule driven by corrosion rate, remaining life and the damage mechanisms the refinery’s review has identified.

Process piping inspection at those plants feeds straight into repair planning. When thickness readings show a circuit approaching its retirement thickness, the replacement spool is designed and fabricated ahead of the turnaround, the change goes through management of change and any damage mechanism review it triggers, and the new piping is installed, tested and documented inside the outage. Paul Industries builds the replacement to the material the review calls for, so a circuit that failed by a known mechanism comes back in a material chosen to resist it. Turnaround planning is covered on shutdown and turnaround services.

CalARP, refinery closures and the renewable feedstock rule

CalARP, the California Accidental Release Prevention program in Title 19, places petroleum refineries in Program 4, administered in most counties by the county’s Unified Program Agency (CUPA), and its refinery amendments took effect on July 1, 2026. The program runs alongside Cal/OSHA’s process safety rules, so refinery piping work answers to both a workplace safety regulator and an environmental one.

The refinery market itself has changed. Phillips 66 ended crude runs at its Los Angeles area refinery in October 2025, Valero completed the idling of its Benicia refinery by the end of April 2026 and kept the site as a gasoline import point, and Phillips 66’s Rodeo plant ended petroleum refining in early 2024 (EIA and company reports). Those changes move piping work toward terminal conversions, product transfer lines and renewable fuel units, and Cal/OSHA’s revised draft of September 2026 would bring refineries that process renewable feedstock under section 5189.1 as well. Paul Industries builds conversion and transfer piping to whichever rule set the site falls under on the day the permit is filed, and storage for those sites is covered on tank fabrication in California.

Seismic bracing for piping under the 2025 California Building Code

Seismic bracing for piping in California follows the 2025 edition of the state building code, in force since the start of 2026, whose seismic chapter points to ASCE 7-22 and the Chapter 13 rules that treat piping systems and their supports as nonstructural components. The building’s seismic design category, the pipe’s size and contents, its importance to life safety and the structure it hangs from decide whether lateral and longitudinal braces are needed and how they are spaced.

California building code seismic bracing reaches beyond the braces themselves. Flexible connections are fitted where piping crosses a seismic joint or meets equipment on its own anchors, so building movement does not shear a nozzle; branch lines are given room to move relative to mains; and hazardous lines get the bracing their contents call for. Paul Industries designs supports, braces and anchors with the piping, includes the calculations in the permit set, and installs and documents them with the line. Vessels and skids those lines connect to are anchored as described on pressure vessel fabrication in California.

Where California plants run process piping

California plants run process piping in five main settings: biotech and pharmaceutical plants in the Bay Area and San Diego, semiconductor fabs and research labs in Silicon Valley, food, dairy, wine and beverage plants in the Central Valley and the coastal valleys, chemical plants, terminals and refining sites around Los Angeles, the Bay Area and Kern County, and data centers and campus central plants across the state.

California regions, their process piping and what drives the design
RegionTypical pipingWhat drives the design
South San Francisco, the East Bay and the PeninsulaPurified water, water for injection, clean steam, CIP supply and return, buffer and media transferASME BPE, drainability, weld documentation for the quality unit, seismic bracing in multistory lab buildings
Santa Clara, San Jose and Silicon ValleyUltrapure water, specialty gas and chemical distribution, process cooling water, acid wasteGroup H-5 rules, welded hazardous production material supply lines, exhausted enclosures, cleanliness
Los Angeles, Long Beach and Orange CountyChemical, fuel transfer, food and beverage, aerospace and medical device process linesSection 5189 and 5189.1 where they apply, terminal conversions, high seismic demand
San Diego and North CountyBiologics clean utilities, lab gases, process waterASME BPE and B31.3, phased work in occupied research buildings
Sacramento, Fresno, Modesto and the Central ValleySanitary product lines, CIP, glycol, ammonia refrigeration, wastewaterPack-season outages, 3-A and sanitary design, hot summers on outdoor racks
Bakersfield and Kern CountyOil field steam, crude and produced water, gas processingSection 5189 thresholds, high temperature service, corrosion

Process piping, Los Angeles and Orange County plants

Process piping Los Angeles plants order spans chemical, food, beverage, aerospace and medical device lines, and the basin’s terminal and refinery sites add fuel transfer and conversion work under the process safety rules. Most of the region sits in a high seismic design category, so bracing and flexible connections are part of every routing decision.

Process piping, San Diego research and biologics campuses

Process piping San Diego biotech and biologics campuses need is mostly sanitary: purified water, clean steam, CIP and transfer lines in stainless tubing, often added to buildings already in use. Work is phased around active labs and production suites, with orbital welds documented for the quality unit and passivation records in the turnover file.

Process piping, Bay Area biotech and Silicon Valley fabs

Process piping Bay Area projects call for splits two ways: sanitary utilities for biotech from South San Francisco to Hayward, and hazardous gas, chemical and ultrapure water distribution for fabs and labs around Santa Clara and San Jose. Sanitary systems for those plants are covered further on sanitary process piping in California.

Industrial piping design, fabrication and installation for California plants

Industrial piping design for a California plant starts with a line list that names the code, the fluid service, the design pressure and temperature, the material and joint type, the test method and the seismic requirement for every line, because each of those decides how the Chapter 14 permit, the process safety review and the inspection will go. Paul Industries prepares the design package or works from the owner’s engineer, and resolves stress, support and bracing before spools are cut.

Industrial piping fabrication off site

Industrial piping fabrication follows as spools built off site to the approved isometrics, with weld maps, heat numbers and examination records carried through, so field welds are kept to tie-ins and closure joints.

Industrial piping installation and the finished industrial piping system

Industrial piping installation then sets supports and braces first, erects the spools, makes the field welds, tests each system to its code and turns the line over with as-builts. The complete industrial piping system reaches the owner as one documented package, from line list to final test, rather than as separate design, shop and field records. Welding procedures and welder qualification for the work are described on industrial welding services in California.

Industrial piping repair and tie-ins at operating California plants

Industrial piping repair at an operating California plant is planned around isolation, the permit and the change process: the line is isolated and drained, the repair or replacement is made, and the system is tested and returned to service with records that satisfy the building department and, at covered processes, Cal/OSHA’s management of change. Chapter 14 treats a repair as permitted work, so even a like-for-like spool change at a non-covered plant goes through the building department.

Tie-ins to live systems are the heart of most California projects, since plants rarely stop for long. Paul Industries surveys the existing lines, prefabricates tie-in spools, schedules hot taps or short outages, and tests new work before it is joined to the live system wherever the code allows. An industrial piping service agreement keeps the same approach on a standing basis for repairs, modifications and inspection support between projects.

Public works piping and California prevailing wage

Public works piping in California, such as water and wastewater treatment plants, public university and hospital central plants and port facilities, is paid at prevailing wage under Labor Code section 1771 when the project exceeds $1,000. Labor Code section 1720 defines public works as construction, alteration, demolition, installation or repair done under contract and paid for in whole or in part out of public funds, and state regulations extend coverage to maintenance contracts. Paul Industries prices public projects at the published prevailing rates for each craft and county and keeps the payroll records those projects require.

What does process piping in California cost?

The cost of process piping in California is set by the length and diameter of each line, its material and joint type, the code and examination level, the number of tie-ins and outages, the seismic bracing, the permit and inspection steps and the documentation the plant needs at turnover. Sanitary stainless tubing with orbital welds and borescope records costs far more per foot than carbon steel utility piping, and hazardous gas lines in a fab cost more again for welded construction, double containment and leak detection.

California adds a few lines of its own: prevailing wage on public projects, design and calculation effort for the Chapter 14 permit and seismic bracing, and on covered processes the engineering behind management of change and damage mechanism reviews. At the concept stage Paul Industries sets a budget range drawn from comparable piping scope, then fixes the price once the line list, isometrics and tie-in plan are defined, with design, fabrication, installation, testing and documentation shown separately.

Who installs process piping in California?

Paul Industries installs process piping in California, taking design, spool fabrication, installation, testing, repair and turnover documentation for plants in San Diego, Orange County, Los Angeles and the Inland Empire, in Ventura and Oxnard, in Bakersfield, Fresno, Modesto and Sacramento, and around the Bay Area from South San Francisco to Silicon Valley. As an industrial piping contractor working under one contract, Paul Industries carries the line list, the permit set, the welds, the tests and the records from start to finish.

Owners who need an industrial piping company for both new lines and the equipment they serve keep the scope together: pumps, skids, vessels, tanks and boilers are built and installed under the same contract. Paul Industries is headquartered in Kilmarnock, Virginia, where its process piping in Virginia work is based, and the same approach runs through process piping in North Carolina.

Process piping from Paul Industries for California plants

Formerly based in northern New Jersey, then Pennsylvania, and now headquartered at 256 Shore Drive in Kilmarnock, Virginia, Paul Industries is an East Coast contractor whose process piping work runs across California, through all 50 states and to plants outside the United States. It designs, fabricates, supplies, installs, tests, repairs and documents process, sanitary, hazardous gas and utility piping for California biotech, semiconductor, food, chemical and fuel sites. Send the P&IDs or line list, the fluid services and design conditions, the building’s seismic data and the outage windows, and request a quote. Other plant systems in the state are gathered on the California page, and neighboring states on the West Coast page.

Standards referenced: ASME B31.3 Process Piping · ASME B31.1 Power Piping · ASME BPE · 2025 California Mechanical Code, Chapter 14 Process Piping · 2025 California Plumbing Code · 2025 California Building Code (ASCE 7-22, Chapter 13) · California Fire Code, Chapter 27 · Title 8 section 5189, Process Safety Management · Title 8 section 5189.1, Process Safety Management for Petroleum Refineries · CalARP Program 4 (Title 19 CCR) · California Labor Code sections 1720 and 1771

Frequently asked questions

Does Paul Industries run clean utility lines for biotech plants from Brisbane to Fremont?

Paul Industries installs process piping for biotech and pharmaceutical plants in South San Francisco, Brisbane, Hayward, Fremont and across the East Bay. Typical scope covers purified water and water for injection loops, clean steam, CIP supply and return and product transfer lines in ASME BPE tubing, with orbital weld logs, borescope records and passivation documents organized for the quality unit at turnover.

Does Paul Industries build gas and chemical piping for fabs in Santa Clara and San Jose?

Yes. Paul Industries builds specialty gas, bulk chemical, ultrapure water, process cooling and acid waste piping for semiconductor fabs and research labs in Santa Clara, San Jose, Milpitas and Sunnyvale. Supply lines for the most toxic gases are welded throughout or run inside exhausted enclosures, as the California Mechanical Code requires, and routing follows the Group H-5 rules of the Fire Code.

Who handles process piping for food, dairy and wine plants around Fresno, Modesto and Lodi?

Paul Industries handles sanitary product lines, CIP, glycol, ammonia refrigeration and wastewater piping for food, dairy, wine and beverage plants around Fresno, Modesto, Turlock, Lodi and Stockton. Work is scheduled into the off season or between production runs, with sanitary welds documented and outdoor racks designed for Central Valley summer heat and the building’s seismic loads.

Does Paul Industries install process piping in the Inland Empire and Orange County?

Yes. Paul Industries installs process piping at manufacturing, food, medical device and distribution plants in Ontario, Riverside, San Bernardino, Irvine, Anaheim and across Orange County. Each job is permitted under Chapter 14 of the California Mechanical Code, braced for the region’s high seismic demand and tested and documented before it goes into service.

Does every process piping change in California need a permit?

Chapter 14 of the California Mechanical Code makes it unlawful to install, alter or repair process piping without a permit, so new lines, modifications and repairs generally go through the building department. The permit application carries plans, calculations and diagrams, and the work gets a rough inspection before it is covered and a final inspection with a pressure test. Paul Industries prepares the permit set with the design.

What pressure test does the California Mechanical Code require on process piping?

The final inspection under Chapter 14 includes a hydraulic test at not less than one and a half times the maximum design operating pressure, or a pneumatic test at 110 percent, held for at least 30 minutes with no perceptible pressure drop. ASME B31.3 sets its own test rules for the fluid service, and Paul Industries writes one procedure that satisfies both.

Which plants fall under California process safety management?

Title 8 section 5189 covers processes holding a chemical at or above the threshold in its Appendix A, or 10,000 pounds or more of a Category 1 flammable gas or a flammable liquid with a flashpoint below 100 degrees Fahrenheit in one location. Ammonia refrigeration, chlorine and many chemical processes fall under it. Petroleum refineries follow section 5189.1 instead, which adds damage mechanism reviews and a hierarchy of hazard controls.

Does a temporary clamp on a leaking refinery line need management of change?

Yes. Title 8 section 5189.1 applies management of change to all changes except replacements in kind, and it names temporary pipe repairs expressly. A clamp, sleeve or enclosure on a leaking refinery line is therefore reviewed for its technical basis and safety impact before it is fitted, and tracked until the permanent repair is made at the next suitable outage.

What is a damage mechanism review and how does it change a piping repair?

A damage mechanism review, required at California refineries by section 5189.1, identifies how each process can degrade its equipment, such as corrosion, cracking or thermal fatigue, and checks that materials suit the service. Reviews are revalidated at least every five years. When piping is replaced, the review’s findings decide the material and design, so the new line resists the mechanism that wore out the old one.

Are renewable diesel plants in California covered by the refinery process safety rule?

Cal/OSHA is working on it. A revised discussion draft issued on September 1, 2026, with an advisory meeting on September 23, 2026, would require refineries that process renewable feedstock to comply with section 5189.1. Until a rule is adopted, those plants follow the general industry rule in section 5189 where their processes meet its thresholds. Paul Industries designs to the rule that applies on the permit date.

What sets the spacing of seismic braces on plant piping in California?

Piping is braced under the 2025 California Building Code and ASCE 7-22 Chapter 13, which set lateral and longitudinal bracing based on the seismic design category, pipe size, contents and importance. Flexible connections are fitted at seismic joints and equipment on separate anchors. Paul Industries designs supports, braces and anchors with the piping, puts the calculations in the permit set and installs them with the line.

Can new process piping be tied into a live system without shutting a California plant down?

Often, yes. Hot taps, short planned outages and prefabricated tie-in spools keep downtime to hours rather than days. New piping is tested before it is joined to the live system wherever the code allows, and the final closure welds are examined on the spot. Paul Industries surveys the existing lines, plans each tie-in with operations and schedules it into the plant’s next suitable window.

Does California prevailing wage apply to piping at a water treatment plant?

Public works over $1,000, defined in Labor Code section 1720 as construction, alteration, installation or repair under contract paid in whole or in part with public funds, are paid at prevailing wage under section 1771, and maintenance contracts are covered as well. Piping at public water and wastewater plants usually falls under that rule. Paul Industries prices those projects at the published rates and keeps the weekly payroll records.

Which records does a California plant receive when new process piping is turned over?

The turnover file carries the permit and inspection sign-offs, the line list, isometrics and as-builts, material certificates and heat numbers, weld maps with welder identification, examination results, pressure test records, seismic bracing calculations and, for sanitary lines, passivation and borescope records. At covered processes, the management of change and pre-startup review records are included so the plant closes the change without gaps.

Is there a difference between process piping and power piping at a California plant?

Yes. Power piping, such as steam and boiler feedwater lines connected to a power boiler, follows ASME B31.1 and the boiler code, and its repairs follow the National Board Inspection Code under Cal/OSHA’s Pressure Vessel Unit. Process piping carrying product, chemicals and process utilities follows ASME B31.3 and Chapter 14 of the California Mechanical Code. Paul Industries marks the boundary on the line list.

What should a California plant send to get process piping priced?

Send the P&IDs or a line list with fluid services, design pressures and temperatures, materials and sizes, plan drawings showing routing and tie-in points, the building’s seismic data, the plant’s outage windows and any process safety or validation requirements. Paul Industries uses them to build a budget range and then a firm price, with design, fabrication, installation, testing and documentation shown separately.

Does Paul Industries install piping at fuel terminals created from closed California refineries?

Yes. As refining units close, sites such as import terminals need new product transfer lines, loading and unloading piping, tank connections and vapor handling. Paul Industries designs, fabricates and installs that piping, braces it for the site’s seismic loads and tests and documents it under whichever process safety and accidental release rules apply to the converted site.

New lines, a tie-in or a piping repair at a California plant?

Send the P&IDs or line list, the fluid services and design conditions, the routing and the outage windows. Call 201-450-8280 or request a quote.