Paul Industries provides tank fabrication in California, designing, building, installing and repairing shop-built and field-erected tanks in carbon steel and stainless steel for wineries, dairies, food and biotech plants, water systems, fuel terminals and generator plants across the state. Three things set a California tank apart from the same tank in most other states: a state petroleum storage law that reaches small facilities, an underground tank program that now accepts only fully double-walled systems, and seismic design that decides the shell, the anchors and the piping connections. Paul Industries builds each tank to the program that governs its contents and to the ground motion at its site.

Request a quote or call 201-450-8280

Headquarters 256 Shore Drive, Kilmarnock, Virginia
Petroleum ASTs APSA applies at 1,320 gallons or more, counting containers of 55 gallons up
Underground tanks Single-walled systems had to close by December 31, 2025
Seismic design ASCE 7-22, adopted through the 2025 California Building Code
Wine California averages 81 percent of US wine production (Wine Institute)
Reviewed November 2026

Shop-built and field-erected tank fabrication in California

Tank fabrication in California splits into shop-built tanks, finished and tested before shipment, and field-erected tanks, built from plate on the owner’s foundation, with the line between them set mostly by road shipping limits on diameter. Shop tanks cover generator day and base tanks, UL 142 fuel tanks, API 12F production tanks, dairy silos and most process tanks; field tanks cover large wine storage, water reservoirs, fire protection storage and terminal tanks built to API 650.

California adds weight to the choice. A field-erected tank is designed for the site’s seismic forces from the start, with shell courses, the bottom-to-shell joint and the anchor pattern sized together, while a shop tank built for another market may need heavier anchorage, thicker supports or a different leg design before it can be set on a California pad. Paul Industries decides shop or field on shipping, schedule, site access and seismic design together, and the national comparison of the two methods is on tank fabrication.

California storage tank regulations at a glance

California storage tank regulations divide tanks by what they hold and where they sit: petroleum above ground falls under the Aboveground Petroleum Storage Act, petroleum and hazardous substances below ground fall under the State Water Board’s underground storage tank program, pressurized and some low-pressure gas tanks fall under the Title 8 Unfired Pressure Vessel Safety Orders, and food, wine and water tanks answer to the building code and their product’s own sanitary rules. Most tank questions begin with sorting the tank into one of those groups.

Which California program governs which tank
Tank and contentsCalifornia programWho administers itWhat the owner owes
Aboveground petroleum: fuel oil, diesel, lube oil, used oil, crudeAboveground Petroleum Storage Act, Health and Safety Code Chapter 6.67CAL FIRE Office of the State Fire Marshal, with Unified Program AgenciesSPCC Plan, annual reporting in CERS, fees, inspection
Underground petroleum or hazardous substancesHealth and Safety Code Chapter 6.7 and Title 23 Chapter 16State Water Resources Control Board, with Unified Program AgenciesOperating permit, double-walled construction, continuous monitoring, testing
Petroleum tanks in basements, vaults or pitsAPSA, as a tank in an underground areaUnified Program AgenciesSPCC Plan even below 1,320 gallons of total storage
LP-gas, anhydrous ammonia and LNG storage at 15 psig or lessTitle 8 Unfired Pressure Vessel Safety Orders, section 450(a)(6)Cal/OSHADesign, construction, repair and alteration to the Orders
Wine, dairy, food and beverage process tanksBuilding code for structure and anchorage; product sanitary rulesBuilding department; food and dairy regulators for the productSeismic anchorage, cleanable design, product contact records
Water and fire protection storageBuilding and fire codes; drinking water rules for public systemsBuilding and fire officials; drinking water regulatorsAWWA design, coatings for potable service, seismic design

The Aboveground Petroleum Storage Act: who it covers

The Aboveground Petroleum Storage Act covers any California tank facility that stores petroleum in aboveground tanks, containers or equipment of 55 gallons or more and meets one of three tests: it is subject to the federal SPCC rule in 40 CFR Part 112, its total aboveground petroleum capacity is 1,320 gallons or more, or it has one or more petroleum tanks in an underground area such as a basement, vault, shaft or pit. Capacity is counted by shell size, not by the amount actually stored.

The California APSA requirements are threefold: prepare and implement an SPCC Plan in the federal format, report the facility each year through the California Environmental Reporting System, and pay the Unified Program fee with its state surcharge. Facilities storing 10,000 gallons or more are inspected by their Unified Program Agency at least once every three years. A short list of exclusions keeps some tanks out of the count, and one matters to plants with mixed equipment: a pressure vessel or boiler regulated under Part 6 of Division 5 of the Labor Code is excluded, which is why a pressurized vessel holding a petroleum product is handled on pressure vessel fabrication in California rather than under APSA.

For a tank builder, the California Aboveground Petroleum Storage Act turns into design inputs. The SPCC Plan needs secondary containment sized for the largest tank plus precipitation, overfill prevention, and an integrity testing schedule, so a new tank is drawn with its containment, its high-level alarm and its inspection access in the first layout. Paul Industries builds double-walled UL 142 tanks for sites where a dike would not fit, and single-walled tanks inside concrete or steel containment where the plant prefers to inspect the shell directly.

APSA vs SPCC: how the state law stacks on the federal plan

APSA vs SPCC is a question of scope, because California’s law adopts the federal plan format and then extends it to tank facilities the federal rule would leave alone. The federal SPCC rule applies above 1,320 gallons of aboveground oil capacity where a discharge could reach navigable waters, while APSA drops the waters test for petroleum and adds tanks in underground areas regardless of total capacity.

How APSA and the federal SPCC rule compare for a California tank facility
Point of comparisonFederal SPCC rule (40 CFR 112)California APSA
Products coveredOil of any kind, including animal and vegetable oilsPetroleum, liquid at 60 degrees Fahrenheit and atmospheric pressure
Capacity triggerMore than 1,320 gallons aboveground, counting containers of 55 gallons or more1,320 gallons or more, counting containers of 55 gallons or more
Location testDischarge could reasonably reach navigable watersNo waters test for petroleum
Tanks in underground areasCounted with other aboveground capacityBring a facility under APSA even below 1,320 gallons
PlanSPCC Plan reviewed by a professional engineer, or prepared by the owner at qualified facilitiesSPCC Plan in the same format; qualified facilities up to 10,000 gallons may prepare their own
Reporting and feesNo routine filingAnnual CERS submittal, Unified Program fee and state surcharge
InspectionEPA inspections as scheduled by the agencyUnified Program Agency inspection at least every three years at 10,000 gallons or more

California underground storage tank regulations after the single-wall deadline

California underground storage tank regulations reached a hard line on December 31, 2025, when every single-walled underground tank and every non-exempt single-walled run of piping had to be permanently closed under Health and Safety Code section 25292.05. The State Water Board granted no extensions, and a system still in the ground without secondary containment is out of compliance, can be red-tagged so that it cannot receive or dispense fuel, and carries penalties of $500 to $5,000 per day, per tank, per violation.

Every underground storage tank California owners install today is a double-walled system. Tanks installed on or after July 1, 2004 meet section 25290.1 of the Health and Safety Code, with the space between the walls continuously monitored by vacuum, pressure or hydrostatic methods and connected to audible and visual alarms, and every component installed since July 1, 2003 sits inside secondary containment that holds both liquid and vapor. Piping, sumps, dispensers and fill connections are part of the same system, so the tank, the piping and the monitoring are designed and tested together.

Owners replacing a closed single-walled system often compare a new underground tank with an aboveground tank under APSA. An aboveground tank avoids continuous interstitial monitoring and excavation, but it needs space, containment, vehicle protection and seismic anchorage, and for emergency generator fuel it brings the tank into the building and fire code review for the generator room. Paul Industries prices both layouts from the same fuel demand, with the closure of the old system, the new tank and its piping in one scope.

Funding and records for replacement projects

The California Underground Storage Tank Cleanup Fund reimburses eligible corrective action costs, and the State Water Board has set December 31, 2034 as the last date for claim applications, with the fund ending on January 1, 2036. Owners who find contamination when a single-walled system comes out should open a claim early, because the review is long. The California underground storage tank program also publishes a map of facilities still listed with single-walled components, which plants use to check that a closure was recorded.

Seismic tank design and the 2014 South Napa earthquake

Seismic tank design in California follows the 2025 California Building Code, effective January 1, 2026 and based on ASCE 7-22, with tanks treated as nonbuilding structures under ASCE 7 Chapter 15 and welded steel storage tanks commonly designed with API 650 Annex E. The magnitude 6.0 South Napa earthquake of August 24, 2014 showed what the calculations protect against, because the worst damage at wineries fell on stainless steel tanks.

A study of the damage published in STRUCTURE magazine in March 2015 found that unanchored legged tanks slid up to about 8 inches and tore their piping, while large flat-bottom tanks anchored to concrete slabs suffered diamond-shaped buckling of the shell, usually together with anchor failure, mostly in tanks that were full. Corroded anchors and anchors pulled out near slab edges were part of the record, and catwalks pounding against tank tops dented shells. That wine tank failure pattern is the reason Paul Industries designs the shell, the anchor chairs, the slab edge distance and the piping flexibility as one system.

Earthquake damage seen in California tanks and the design answer for each
Damage seenTank type affectedDesign response
Sliding and torn pipingUnanchored legged stainless tanksAnchored legs with base plates, flexible hoses or loops at each connection
Diamond-shaped shell bucklingTall, slender flat-bottom tanks, mostly fullShell thickness and aspect ratio checked for seismic compression; height to diameter limited where possible
Anchor pullout at the slab edgeAnchored flat-bottom tanksAnchor chairs, embedment and edge distance designed with the slab engineer
Corroded anchorsOlder tanks in wash-down areasStainless or coated anchors, drainage away from the base, inspection access
Dented shells from catwalksTank rows joined by walkwaysWalkway supports set apart from the tank, with movement gaps
Vacuum damage to upper coursesClosed tanks drained quickly or cooledVacuum relief sized for the drain and cooling rates

What are wine tanks called, and how are they built?

Wine tanks are usually called fermenters or fermentation tanks while the juice is turning to wine, and storage or blending tanks afterward, with variable capacity tanks, open-top fermenters, jacketed tanks and legged tanks naming the common shapes. California averages 81 percent of the nation’s wine production according to the Wine Institute, so most of the country’s wine tanks stand in Napa, Sonoma, the Central Coast, Lodi and the Central Valley.

Wine tank sizes span a wide range: legged tanks in the Napa study held about 10 to 50 cubic meters, roughly 2,600 to 13,200 gallons, while flat-bottom storage tanks in the Central Valley reach far larger volumes. Paul Industries builds jacketed stainless fermenters with glycol jackets zoned for cap management and cold stabilization, sloped bottoms and racking valves, manways and sample valves placed for cellar work, and anchors and legs designed for the site’s seismic forces rather than a catalog default.

Stainless steel tank fabrication: California dairies, wineries and food plants

Stainless steel tank fabrication for California dairies, wineries and food plants turns on the finish, the cleanability and the cooling. California led the nation in milk production in 2025 according to USDA, and its dairy plants buy insulated silo tanks, processing vats and CIP tanks, while Central Valley tomato and fruit processors buy surge, blend and aseptic hold tanks timed to a short harvest season. Paul Industries supplies these tanks with sanitary welds, polished product surfaces, CIP spray coverage and the documentation a plant’s food safety plan expects, with dairy plants covered further on dairy processing and plant process tanks on process tanks.

Which tanks do California’s regions order?

California’s tank demand follows its industries region by region, and the same seismic rules apply to all of them. Wineries and dairies dominate the agricultural valleys, biotech and semiconductor plants concentrate in the Bay Area and San Diego, and fuel storage clusters around the Los Angeles and Bay Area ports and the Kern County oil fields.

California regions and the tanks their sites typically order
RegionTypical tanksGoverning programSite detail
Napa, Sonoma, Lodi and the Central CoastJacketed fermenters, storage and blending tanksBuilding code anchorageTank rows with catwalks; harvest schedule
Sacramento, Fresno and the Central ValleyDairy silos, processing vats, tomato and fruit surge tanks, diesel tanksBuilding code; APSA for fuelHot summers; pack season shutdown windows
San Francisco Bay Area and South San FranciscoStainless process and water tanks, generator fuel, import terminal tanksAPSA and UST for fuel; API 653 at terminalsTight urban sites, soft bay soils
Silicon Valley and Santa ClaraGenerator day and base tanks, chemical and water tanksAPSA; tanks in underground areasBasement and vault tanks under APSA
Los Angeles, Long Beach and Orange CountyTerminal tanks, food and cosmetics process tanks, fuel tanksAPSA, UST, API 650 and 653Port terminals; refinery sites in transition
Inland Empire and San DiegoWater and fire storage, food process tanks, biotech tanksBuilding and fire codes; APSA for fuelHot inland summers; coastal exposure in San Diego
Bakersfield and Kern CountyAPI 12F production tanks, water and fuel tanksAPSA and oil field rulesProduction field access and spacing

Fuel terminals after California’s refinery closures

California’s refining base has shrunk in steps, and the tanks at closed sites keep working in new roles. The Martinez refinery shut in 2020 and Rodeo turned away from crude oil in early 2024. Crude runs at the Phillips 66 Los Angeles refinery ended in October 2025, with its Carson and Wilmington sites now under a redevelopment study, and Benicia’s last units were idled by the end of April 2026, leaving Valero’s site in use as a gasoline import terminal.

Import terminals and blending sites need tanks converted from refinery service to finished product storage, new internal floating roofs and seals, tank bottom replacements, and new connections for marine and truck loading. Paul Industries repairs, modifies and builds terminal tanks to API 650 and API 653, with the transfer piping set out on process piping in California. For tank fabrication, Los Angeles terminals and the Bay Area’s import sites schedule the work around product movements, so tanks come out of service one at a time.

Water tank fabrication for California utilities and plants

For water tank fabrication, California utilities, campuses and plants order welded steel reservoirs, fire protection storage and process water tanks designed to AWWA D100 and to the seismic forces of the site. Water tanks sloshing during an earthquake push on the roof and upper shell, so freeboard, roof framing and the overflow are part of the seismic design, and potable tanks use interior coatings accepted for drinking water. Paul Industries builds and installs water tanks with their foundations, piping, level instruments and access, and plants with ultrapure and process water storage can read validation and commissioning in California for how those systems are documented.

Aboveground storage tank repair or replacement in California

Aboveground storage tank repair in California follows API 653 for field-erected steel tanks, with the inspection findings deciding between a bottom replacement, shell course repairs, a new floating roof or a new tank. Shop-built tanks under APSA are inspected on the schedule in the facility’s SPCC Plan, often using the steel tank industry inspection standard, and a tank that fails integrity testing is repaired to its original standard or replaced.

Entry for inspection and repair is permit-required confined space work under Title 8 section 5157, so cleaning, ventilation, atmospheric testing, isolation and rescue planning come before the first weld. Paul Industries cleans, inspects, repairs and recoats tanks, cuts in new nozzles, replaces bottoms and shell courses, and builds replacement tanks where the inspection shows repair is the more expensive path, with welding work set out on industrial welding services in California and cleaning on industrial tank cleaning.

What does tank fabrication in California cost?

The cost of tank fabrication in California is driven by capacity, material and plate thickness, shop or field construction, roof type, jackets and insulation, interior finish and coatings, nozzle count, seismic anchorage and foundation design, containment, and the regulatory work that comes with the contents. Stainless tanks with polished interiors and glycol jackets cost several times a carbon steel tank of the same volume, and a double-walled underground fuel system with monitoring costs far more than the tank shell alone.

California adds seismic design to every tank, which can mean thicker lower courses, more anchors and heavier slabs, along with APSA or UST compliance work for fuel tanks. Wine tank cost follows the same drivers: volume, jacket zones, finish, legs or flat bottom, and anchorage. Paul Industries gives a budget range from comparable scope once the volume, contents and site are known, and a firm price that separates the tank, foundation, containment, piping and testing.

Who fabricates tanks in California?

Paul Industries fabricates tanks in California, designing, building, installing, inspecting and repairing them for wineries in Napa, Sonoma and the Central Coast, dairies and food plants from Sacramento and Modesto to Fresno and Tulare, biotech plants in South San Francisco, Solano County and San Diego, terminals and plants in Los Angeles, Orange County and the Bay Area, and water and fuel systems statewide. Headquartered at 256 Shore Drive in Kilmarnock, Virginia, after earlier bases in northern New Jersey and Pennsylvania, Paul Industries is an East Coast contractor taking tank work throughout California and in all 50 states.

Tank manufacturers in California and elsewhere build to the same API, UL and AWWA standards, so the decision rests on who carries the tank through the California steps: seismic design, APSA or UST compliance, installation and the records that follow. Paul Industries offers supply of the tank alone, design-build of the tank with its foundation, containment and piping, or complete installation through startup. Readers comparing headquarters-state work can see tank fabrication in Virginia, and a coastal comparison is tank fabrication in Florida. Pacific region coverage is on the West Coast page.

Paul Industries tank scope for California sites

Paul Industries designs, fabricates, installs, inspects and repairs shop-built and field-erected tanks for California plants, wineries, dairies, terminals and water systems, with seismic anchorage, containment and the APSA or UST records each tank needs. Send the contents, volume, dimensions or site limits, material and any jacket or finish requirements, then call 201-450-8280 or request a quote. Paul Industries’ other California work in process, piping and water systems is listed on the California page.

Standards referenced: Aboveground Petroleum Storage Act (Health and Safety Code Chapter 6.67) · California underground storage tank law (Health and Safety Code Chapter 6.7) and Title 23 Chapter 16 · 40 CFR Part 112 (SPCC) · API 650 and Annex E · API 653 · API 12F · UL 142 · AWWA D100 · 2025 California Building Code · ASCE 7-22 · Title 8 section 5157 (Permit-Required Confined Spaces) · Title 8 Unfired Pressure Vessel Safety Orders

Frequently asked questions

Who builds stainless fermenters and storage tanks for Napa and Sonoma wineries?

Paul Industries builds jacketed stainless fermenters, storage and blending tanks for wineries in Napa, Sonoma, Lodi and the Central Coast, with glycol jacket zones, sloped bottoms, racking and sample valves, and catwalk supports that stand clear of the tanks. Legs, anchors and slab edge distances are designed for the site’s seismic forces, the lesson of the 2014 South Napa earthquake.

Does Paul Industries fabricate fuel and terminal tanks for Los Angeles, Long Beach and the Bay Area?

Yes. Paul Industries fabricates, repairs and modifies fuel and terminal tanks around Los Angeles, Long Beach, Carson and the Bay Area, including bottom replacements, floating roof work, new nozzles and new API 650 tanks. Work at operating terminals is sequenced so one tank leaves service at a time, and each tank returns with API 653 records and updated SPCC information.

Who supplies dairy silos and process tanks for Central Valley plants from Modesto to Tulare?

Paul Industries supplies and installs insulated silo tanks, processing vats, CIP tanks and blend tanks for dairy, tomato, fruit and nut processing plants from Modesto and Turlock through Fresno, Hanford and Tulare. Tanks are scheduled around harvest and pack seasons, built with sanitary welds and polished product surfaces, and anchored for the seismic forces at each plant.

What agency oversees the underground storage tank program in California?

The State Water Resources Control Board oversees the underground storage tank program statewide under Health and Safety Code Chapter 6.7 and Title 23 Chapter 16, and Unified Program Agencies, usually county environmental health or fire departments, issue operating permits, inspect sites and enforce the rules. Both can enforce the single-walled closure requirement and red-tag a noncompliant system.

Which California aboveground storage tank regulations apply to a generator day tank?

A day tank or base tank holding diesel counts toward the facility’s aboveground petroleum capacity under APSA when it holds 55 gallons or more, so a site with 1,320 gallons or more in total needs an SPCC Plan and annual CERS reporting. The tank also falls under the building and fire codes for the generator room, which govern its size, venting and containment.

Do California aboveground storage tank rules apply to a tank in a basement?

Yes. A petroleum tank in a basement, vault, pit or shaft is a tank in an underground area under APSA, and one such tank brings the facility under the Act even when its total aboveground petroleum storage is below 1,320 gallons. The facility then prepares an SPCC Plan and reports in CERS like any other APSA tank facility.

Can a single-walled underground tank still be used in California?

Single-walled underground tanks and non-exempt single-walled piping had to be permanently closed by December 31, 2025, with no extensions. A system still in service can be red-tagged so it cannot receive or dispense fuel, and owners face penalties of $500 to $5,000 per day per tank. Replacement is a double-walled, continuously monitored system or an aboveground tank under APSA.

Is a propane or ammonia storage tank handled under APSA?

LP-gas is a gas at 60 degrees Fahrenheit and atmospheric pressure and ammonia is no petroleum product, so both sit outside APSA’s definition of petroleum, and those tanks fall under the Title 8 Unfired Pressure Vessel Safety Orders instead, which also reach LNG, LPG and ammonia storage tanks operating at 15 psig or less. Pressurized LP-gas tanks above 125 gallons need a Cal/OSHA permit to operate before they are filled.

How should a winery anchor legged stainless tanks after the Napa earthquake?

Legged tanks should be anchored at every leg with base plates bolted to a slab designed for the uplift and shear, because unanchored legged tanks in the 2014 South Napa earthquake slid up to about 8 inches and tore their piping. Flexible hoses or pipe loops at each tank connection, and catwalks supported apart from the tanks, protect the piping and shells.

What size tank can be shipped to a California site?

Shop-built tanks are limited mainly by road shipping width and height, and oversize loads need route surveys, permits and escorts that grow with every added foot of diameter. Larger tanks are field-erected on the owner’s foundation. Paul Industries checks the delivery route, crane access and setting area before choosing between a shop tank and a field-erected one.

Are wine and food tanks covered by California's petroleum tank laws?

Wine, dairy, juice and food tanks fall outside APSA and the underground storage tank program because they hold no petroleum or hazardous substance. They still need a building permit where the building department requires one, seismic anchorage to the California Building Code, and sanitary design suited to the product and the plant’s food safety plan.

How often are APSA tank facilities inspected in California?

Tank facilities with 10,000 gallons or more of aboveground petroleum capacity are inspected by their Unified Program Agency at least once every three years, and smaller facilities on the schedule the agency sets. The owner also inspects tanks under its own SPCC Plan, often to the steel tank industry inspection standard for shop-built tanks and API 653 for field-erected tanks.

What does a new double-walled underground tank system include in California?

A new system includes a double-walled tank, double-walled piping, containment sumps at the turbine and dispensers, spill containment at the fill, overfill prevention, and continuous interstitial monitoring by vacuum, pressure or hydrostatic methods with audible and visual alarms. Every component installed since July 1, 2003 is inside secondary containment. Paul Industries installs and tests the system before the operating permit is issued.

Should a California fuel tank go above or below ground?

An aboveground tank avoids excavation and continuous interstitial monitoring and is easier to inspect, but it needs space, containment, vehicle protection and seismic anchorage. An underground tank saves space and keeps fuel out of sight, but costs more to install and monitor. Paul Industries prices both layouts for the same fuel demand so the owner can compare them on one page.

Can an old refinery tank be reused at a California import terminal?

Often, yes, after an API 653 inspection confirms the bottom, shell and roof can serve the new product. Conversions usually add or replace internal floating roofs and seals, change nozzles and mixers, and update overfill protection and the facility SPCC Plan. Paul Industries inspects, repairs and modifies the tank and documents the change of service.

Who builds water and fire protection tanks for San Diego and Inland Empire sites?

Paul Industries builds welded steel water reservoirs, fire protection storage and process water tanks for campuses, plants and utilities in San Diego, Riverside, San Bernardino and Ontario. Tanks are designed to AWWA D100 with sloshing, freeboard and roof framing checked for the site’s seismic forces, and potable tanks receive interior coatings accepted for drinking water.

Which details start a tank price for a California site?

Send the contents, volume, preferred diameter or height limits, material, roof type, any jacket, insulation or interior finish, the nozzle list, site address and the containment you have or plan. For fuel tanks, add the existing APSA or UST status. Paul Industries uses that to set seismic design, containment and shipping method, then prices the tank, foundation and installation.

Planning a tank for a California site?

Send the contents, volume, size limits, material and site address, plus any APSA or UST status for fuel tanks. Call 201-450-8280 or request a quote.