Paul Industries designs, builds and services ultrapure water systems in California: pretreatment, double-pass reverse osmosis, electrodeionization, polishing, ultraviolet and ultrafiltration, with PVDF and polypropylene distribution loops for semiconductor R&D, biotech laboratories, medical device plants and battery and materials research from Silicon Valley to San Diego. California hands an ultrapure plant sharply different feedwater from one region to the next: soft Sierra snowmelt in San Francisco, hard and salty imported water in San Diego, and advanced-treated recycled water in San Jose. Paul Industries designs each plant around the water that actually arrives at the site.
Request a quote or call 201-450-8280
Demand for ultrapure water systems in California, by industry and region
Ultrapure water systems in California are being built and expanded wherever chips, instruments and biologics are researched or made: semiconductor equipment and process R&D in Santa Clara, Sunnyvale, San Jose and Fremont; biotech and diagnostics laboratories in South San Francisco, the East Bay and San Diego; medical device plants in Orange County, the Inland Empire and San Diego; and university and national laboratory research across the state. Most California demand is research, pilot and specialty production rather than high-volume wafer fabs, which shapes system sizes and loop layouts. Treatment principles that hold everywhere, from resistivity to resin life, are explained on the ultrapure water systems page; this page deals with what California’s water, rules and buildings change.
Ultrapure water: semiconductor R&D in Silicon Valley
Ultrapure water semiconductor research needs is concentrated in Silicon Valley. In October 2026 Applied Materials unveiled its EPIC Center in Sunnyvale, a building of about 55,700 square meters with roughly 1.6 hectares of cleanroom for collaborative process and equipment research with chipmakers and universities. Equipment makers, materials suppliers and startups across the valley run tool demonstration labs and pilot lines on smaller ultrapure plants, each needing water that meets electronics-grade limits at the point of use. Those facilities are market facts about where the demand sits; the systems they need are what this page covers.
Biotech, diagnostics and device laboratories
Biotech, diagnostics and medical device laboratories use ultrapure water for cell culture media, analytical chemistry, mass spectrometry, molecular biology and rinse steps, and they often run it alongside compendial Purified Water systems in the same building. Those buildings need clear separation between the ultrapure loop and the compendial system, which is regulated differently; the compendial side is covered on high-purity water systems in California.
California feedwater: why the same ultrapure plant cannot fit every site
California feedwater varies widely from one city to the next, because cities draw from Sierra snowmelt, the Colorado River, the State Water Project, groundwater and, increasingly, recycled water. The reverse osmosis design, recovery, antiscalant program and pretreatment change with that source, so the first step on any California ultrapure project is a full water analysis from the site’s own tap.
| Supply | Reported 2024 values | Effect on the ultrapure train |
|---|---|---|
| San Francisco Public Utilities Commission regional system (Hetch Hetchy and Bay Area reservoirs) | Total dissolved solids 24 to 169 mg/L, average 102; hardness 8.4 to 106 mg/L as CaCO3, average 60; silica average 7.5 mg/L | Low scaling load; high RO recovery is practical; seasonal blend changes need monitoring |
| City of San Diego treated water (imported Colorado River and State Water Project blend) | Plant averages of about 480 to 570 mg/L total dissolved solids; hardness about 216 to 230 mg/L; sodium about 79 to 109 mg/L | Heavier scaling and ionic load; softening or antiscalant, lower recovery, second pass RO before EDI |
| Advanced-treated recycled water (Valley Water, San Jose) | Treated by microfiltration, reverse osmosis and ultraviolet; up to 8 million gallons a day | Very low dissolved solids; front end simplified, but supplier conditions of use and organics monitoring govern |
| Central Valley groundwater | Varies by well; site analysis required | Hardness, silica, nitrate or arsenic set pretreatment; well changes call for retesting |
The San Francisco and San Diego figures differ by roughly five times in dissolved solids and three to four times in hardness, which is the difference between a two-stage RO that runs at high recovery with little chemistry and one that needs softening or careful antiscalant dosing, more reject water and more frequent cleaning. Silica deserves its own attention because it limits RO recovery and is a key impurity in electronics-grade water.
Ultrapure water system design for California sites
Ultrapure water system design for California sites follows the standard treatment sequence, pretreatment, reverse osmosis, electrodeionization, polishing and distribution, but sizes each stage to the supply at the site, the state’s power prices, seismic rules and the discharge limits for the reject stream. The ultrapure water purification system is a chain, and removing an impurity at the earliest stage able to handle it usually costs least.
In the Bay Area, soft feed lets the reverse osmosis run at high recovery, and the design effort goes into the polishing end: total organic carbon reduction with 185-nanometer ultraviolet, mixed-bed polishing, degasification for dissolved oxygen where tools demand it, and final ultrafiltration. In San Diego and much of Southern California, hard, high-solids feed shifts effort to the front: multimedia or ultrafiltration pretreatment, softening or antiscalant, two-pass reverse osmosis, then electrodeionization. Paul Industries specifies each stage from the site analysis and the point-of-use requirement, then models water, chemical and energy use for the whole plant.
| Stage | Purpose | California design factor |
|---|---|---|
| Pretreatment | Remove chlorine or chloramine, particles and hardness before membranes | Chloramine is used by many California utilities; carbon or bisulfite sized for it; softening where feed is hard |
| Reverse osmosis (one or two pass) | Remove most dissolved solids and organics | Recovery set by the site’s hardness and silica; reject volume affects sewer discharge limits and water cost |
| Electrodeionization | Continuous ion removal without chemical regeneration | Needs low hardness and carbon dioxide from the RO; second pass often needed on Southern California feed |
| Polishing and ultraviolet | Final ion removal, organic carbon reduction and bacteria control | Resin life and UV lamp sizing follow the feed’s organic content |
| Ultrafiltration and distribution | Particle removal and continuous recirculation to points of use | Loop materials, seismic bracing of tanks and piping, and pump energy at California power prices |
Which ultrapure water standards do California labs and fabs specify?
The ultrapure water standards California labs and fabs specify depend on the use: ASTM D1193 and ISO 3696 for laboratory reagent water, ASTM D5127 and the SEMI F63 guide for electronics and semiconductor water, and the instrument or tool maker’s own limits where they are tighter. ASTM D1193 Type I water, the usual laboratory target, calls for resistivity above 18 megohm-centimeters at 25 degrees Celsius and total organic carbon of 50 micrograms per liter or less.
Semiconductor R&D sets far tighter limits on particles, organic carbon, dissolved oxygen, silica and metals than laboratory work does, measured in parts per billion or below, and tool demonstration labs often need water that matches what a customer fab delivers. Paul Industries agrees the specification, the sampling points and the online analyzers at the start of design, because a specification set after the plant is built is the most expensive kind.
Laboratory ultrapure water system or central plant?
A laboratory ultrapure water system at each bench and a central plant with a polishing loop are the two ways California research buildings supply Type I water, and the choice turns on the number of users, the volumes they draw and the building’s future. Point-of-use units fed from a building Purified Water or reverse osmosis loop suit buildings with a handful of users; a central plant with a recirculating loop suits buildings where dozens of labs or tools draw ultrapure water through the day.
California’s lab building market adds a third consideration: many South San Francisco, East Bay and San Diego buildings are leased shells fitted out for successive tenants. A central pretreatment and reverse osmosis plant owned by the building, with tenant-owned polishing at the bench, gives landlords a utility they can offer every tenant and lets tenants choose their final water quality. Paul Industries designs either model, and the cleanroom side of those fit-outs is covered on cleanrooms in California.
Point-of-use specifications by California user type
Point-of-use specifications differ sharply between the user types that buy ultrapure water in California, and the loop design follows the tightest user on it. A biotech building and a tool demonstration lab can both say they need 18 megohm water and still need very different systems, because the limits that cost money are organic carbon, particles, dissolved oxygen, silica and metals rather than resistivity alone.
| User type | Usual reference | Parameters that drive the design | System approach |
|---|---|---|---|
| Analytical and molecular biology labs | ASTM D1193 Type I, ISO 3696 Grade 1 | Resistivity, organic carbon, bacteria, endotoxin for some assays | Central reverse osmosis with bench polishers, or a central polishing loop |
| Semiconductor process and equipment R&D | ASTM D5127, SEMI F63, tool maker limits | Particles, organic carbon, dissolved oxygen, silica and metals at parts per billion or lower | Full generation train with degasification, polishing, ultrafiltration and PVDF loop |
| Medical device cleaning and rinse | Device maker’s validated specification | Resistivity, organic carbon, bacteria and residue on parts | Reverse osmosis and electrodeionization with polishing; sanitizable loop |
| Battery, materials and coatings research | Process-specific limits | Specific ions, silica and metals that affect the material | Train selected for the ions that matter; point-of-use polishing |
Paul Industries writes the point-of-use specification for each user into the basis of design, sets sampling points where each limit is measured, and selects online analyzers for the parameters that change fastest, so the owner can show at any time that each user receives water inside its limits.
Sanitization and microbial control in California loops
Sanitization and microbial control in California ultrapure loops depend on the loop material and the users’ tolerance for downtime, and warm mechanical spaces in Southern California and inland buildings make control more demanding. Bacteria grow faster in warm, still water, so loops are designed for continuous recirculation at velocities that discourage biofilm, with short dead legs at every point of use.
Ultraviolet at 254 nanometers controls bacteria in recirculation, ozone dosed into storage and destroyed by ultraviolet before the loop is a common approach for PVDF systems, and hot water or chemical sanitization is scheduled where the material and users allow it. Loop temperature also matters: pump heat and warm rooms raise water temperature over the day, and a small heat exchanger on the return keeps the loop inside the range where analyzers, users and microbial control all perform. Paul Industries designs the sanitization method into the loop from the start, with the valves, drains and injection points it needs, and runs the first sanitization during commissioning.
Monitoring, analyzers and the records California users keep
Monitoring and the records California users keep turn an ultrapure plant from a piece of equipment into a utility that tools and laboratories can rely on, and they are what an auditor, a tool qualification team or a tenant asks for first. Online resistivity at the polishing outlet and the loop return, organic carbon, particle counts on semiconductor loops, dissolved oxygen where specified, flow, pressure and temperature form the usual set.
Paul Industries installs the analyzers with sample lines kept short and clean, connects them to the plant controls with alarm limits set below the user specification so trends are caught early, and calibrates them at startup with the records filed in the turnover package. Periodic grab samples for bacteria, metals or silica are scheduled by the users’ needs. The trend history matters most when something changes, such as a utility switching its source blend in summer, because the record shows exactly when water quality moved and how the plant responded.
Seismic bracing, materials and loop construction
Seismic bracing, materials and loop construction for California ultrapure systems start with the storage tank and the long runs of thermoplastic piping, because both move in an earthquake in ways a steel system does not. Design forces for that equipment come from Chapter 13 of ASCE 7-22, which treats a water tank, a membrane skid and a thermoplastic loop as nonstructural components; California’s building code has referenced the 2022 edition of that standard for permits since the start of 2026.
Paul Industries anchors storage tanks, reverse osmosis and polishing skids to their calculated forces, supports and braces PVDF and polypropylene piping at spacings that account for its lower stiffness and thermal expansion, and adds flexible connections where piping crosses building joints or meets skids. Loops are built with butt-fusion or infrared-welded joints, purged and pressure tested, then rinsed up until resistivity, organic carbon and particle counts meet the specification at the farthest point of use. Stainless sections, where specified for compatibility or heat, follow the welding and passivation practice on passivation services in California, and storage vessels on tank fabrication in California.
Water, reject streams and power in a California ultrapure plant
Water, reject streams and power dominate the operating cost of a California ultrapure plant, and each is more expensive or more scrutinized here than in most states. Reverse osmosis reject is discharged to the sanitary sewer under the wastewater agency’s industrial discharge limits, and on hard Southern California feed the reject volume and its concentrated hardness and salts can approach those limits as recovery rises.
Paul Industries designs reject handling with the discharge permit in hand: recovery set to stay inside the limits, reject reused for cooling tower make-up or other non-critical uses where water chemistry allows, and flow metering that documents what leaves the site. Power is the other line. Pumps for reverse osmosis, polishing and loop recirculation run continuously, and at California’s 2024 industrial average of 21.53 cents per kilowatt-hour, 75 kilowatts of continuous pumping costs about $141,000 a year, against about $53,000 at the national average of 8.13 cents (EIA). The example is illustrative; variable speed loop pumps, efficient high-pressure pumps and right-sized recirculation reduce it, and Paul Industries prices those options against the site’s tariff.
Outages, restarts and loop quality
Outages, restarts and loop quality are linked in California because utility outages, including shutoffs during fire weather in some regions, stop recirculation, and still water in a loop loses quality in a matter of hours as bacteria grow and resistivity drifts. The plant’s response to an outage is therefore part of its design, not an afterthought.
Paul Industries puts loop recirculation pumps, ultraviolet units and the controls that run them on standby power where the users need water through an outage, sizes storage so the loop can be fed while generation restarts, and writes a restart sequence that flushes, checks analyzers and confirms water quality before points of use are reopened. Where standby power is not provided, the sequence covers draining or isolating loop sections, sanitizing after a long stop and documenting the return to specification. Reverse osmosis membranes also need care: a train left full of concentrate when power drops is flushed with permeate on restart to protect the membranes from scaling, a step that matters most on hard Southern California feed.
Expanding a running California ultrapure loop
Expanding a running California ultrapure loop means adding points of use, polishing capacity or a new loop branch without contaminating water that tools and instruments are using. The work is planned with the users so that tie-ins happen during a scheduled outage or through valves and sections that can be isolated and rinsed separately.
New sections are fabricated with clean practices, installed, pressure tested and purged, then rinsed and sampled on their own until they meet the specification before they are opened to the main loop. Paul Industries confirms that the existing generation capacity can carry the added draw at peak, including the flushing water the new section consumes at startup, and records resistivity, organic carbon and particle results for each new point of use before release.
What makes up an ultrapure water system price in California?
An ultrapure water system price in California is made up of the generation capacity and quality required, the pretreatment that the site’s feed needs, the number and length of loops and points of use, loop materials, analyzers, storage, seismic anchorage and bracing, reject handling, controls and the qualification records at turnover. Feedwater alone can change the front end substantially between a Bay Area and a San Diego site of the same size.
Paul Industries gives a budget range from comparable scope once the flow, quality, feedwater analysis and building layout are known, and a firm price after design review.
Operating cost belongs in the same comparison, because over ten years the water, power, chemicals, resin, membranes, lamps and filters a plant consumes often rival what it cost to build, and in California both water and power are priced above the national norm. A design that recovers more reverse osmosis permeate, runs loop pumps at variable speed and sizes ultraviolet and polishing for the real organic load costs more to build in some cases and less to own. Paul Industries presents capital and ten-year operating estimates side by side so the owner chooses on total cost. Routes include supply only of reverse osmosis, electrodeionization and polishing skids, design-build from a flow and quality target, and complete installation including loops, analyzers, rinse-up and turnover.
Who installs ultrapure water systems in California?
Paul Industries installs ultrapure water systems in California, designing, supplying, building, rinsing up, starting and servicing pretreatment, reverse osmosis, electrodeionization, polishing, ultraviolet, ultrafiltration, storage and PVDF or polypropylene loops for semiconductor R&D, biotech and diagnostics laboratories, medical device plants and research institutions. With headquarters at 256 Shore Drive, Kilmarnock, Virginia, Paul Industries builds ultrapure plants in Santa Clara, Sunnyvale, San Jose, Fremont, South San Francisco, the East Bay, Los Angeles, Orange County and San Diego, and in all 50 states.
Ultrapure systems share buildings with process piping, cleanrooms and cooling. Process piping standards are described on process piping in California, and treated water for liquid-cooled racks on data center liquid cooling in California. Companies with sites in other states can compare this page with ultrapure water systems in Virginia, the headquarters state, and ultrapure water systems in North Carolina. Work in the other Pacific states is on the West Coast page.
Next step for ultrapure water at a California site
Paul Industries builds California ultrapure water plants around the site’s feedwater, the users’ specification, seismic rules, discharge limits and power prices, and keeps them running with service, resin and lamp changes and analyzer calibration. Send a recent feedwater analysis or the utility name, the flow and quality needed at each point of use, the building layout and any existing system drawings. Call 201-450-8280 or request a quote. The California page shows the full range of process and water work Paul Industries carries out in the state.
Standards referenced: ASTM D1193 (reagent water) · ASTM D5127 (electronics and semiconductor water) · SEMI F63 (ultrapure water guide) · ISO 3696 (laboratory water) · 2025 California Building Code (Title 24, Part 2) and ASCE 7-22 · 2025 California Plumbing Code (Title 24, Part 5)
Frequently asked questions
Which contractor builds ultrapure water systems for Silicon Valley R&D in Santa Clara and Sunnyvale?
Paul Industries builds ultrapure water systems for semiconductor equipment labs, tool demonstration sites, materials research and pilot lines in Santa Clara, Sunnyvale, San Jose and Fremont. Soft regional feedwater lets the reverse osmosis run at high recovery, so the design effort goes into polishing, organic carbon reduction, degasification and particle control at each tool.
Does Paul Industries install ultrapure water for biotech labs in South San Francisco and the East Bay?
Yes. Paul Industries installs central ultrapure plants, polishing loops and point-of-use systems for biotech and diagnostics laboratories in South San Francisco, Emeryville, Berkeley, Hayward and Fremont, often as part of tenant fit-outs in leased lab buildings. Ultrapure loops are kept separate from compendial Purified Water systems in the same building.
Who builds ultrapure water systems in San Diego and Orange County?
Paul Industries builds ultrapure water systems for life science, diagnostics and medical device sites in San Diego, Carlsbad, Irvine and the rest of Orange County. Feedwater there is hard and high in dissolved solids, so plants typically use softening or antiscalant, two-pass reverse osmosis and electrodeionization, with reject volume designed to stay inside the sewer discharge limits.
Does Paul Industries take ultrapure water projects in Los Angeles and the Inland Empire?
Yes. Paul Industries takes ultrapure water projects for aerospace, electronics, coatings, battery research and laboratory sites across Los Angeles County, Riverside and San Bernardino. Each plant is sized from a site water analysis, because supplies across greater Los Angeles range from imported river water to groundwater pumped from the basins, with different hardness and silica.
Why does San Diego feedwater need a different RO design from San Francisco feedwater?
The City of San Diego’s 2024 report shows treatment plant averages of about 480 to 570 mg/L of dissolved solids and about 216 to 230 mg/L of hardness, while San Francisco’s regional system averaged 102 mg/L of dissolved solids and 60 mg/L of hardness. Harder, saltier feed limits recovery, adds scaling control and often needs a second RO pass before electrodeionization.
Can recycled water feed an ultrapure water plant in Silicon Valley?
Advanced-treated recycled water from Valley Water’s San Jose plant, which uses microfiltration, reverse osmosis and ultraviolet, starts with very low dissolved solids, which simplifies the front end of an ultrapure plant. Its use depends on the supplier’s conditions of use and the organics profile, so Paul Industries reviews supplier water quality data and plans monitoring before designing around it.
How does chloramine in California tap water affect an ultrapure plant?
Many California utilities disinfect with chloramine rather than free chlorine, and chloramine passes through carbon more slowly and can release ammonia that reverse osmosis rejects poorly. Pretreatment therefore uses catalytic carbon with longer contact time or bisulfite dosing, with monitoring that confirms removal before the membranes. Paul Industries sizes that stage from the utility’s disinfection practice.
Is a laboratory ultrapure water system at each bench enough for a Bay Area research building?
For a few users, yes: an ultrapure water system for laboratory benches, using polishers fed from a building reverse osmosis or Purified Water loop deliver Type I water at low capital cost. Buildings with many labs or tools usually save money with a central plant and polishing loop. In leased lab buildings, a landlord-owned central reverse osmosis plant with tenant polishing often balances cost and control well.
What does ASTM D1193 Type I water require?
ASTM D1193 Type I reagent water calls for resistivity above 18 megohm-centimeters at 25 degrees Celsius and total organic carbon of 50 micrograms per liter or less, with limits on sodium, chloride and silica. It is the usual target for analytical and molecular biology laboratories. Semiconductor work uses ASTM D5127 and SEMI F63, which set far tighter limits.
How are ultrapure water tanks and loops braced for earthquakes in California?
California’s current building code points to ASCE 7-22, and its nonstructural chapter sets the earthquake loads on tanks, skids and pipe. Tanks are anchored to calculated forces, thermoplastic piping is supported and braced at spacings that suit its lower stiffness and thermal movement, and flexible connections are used at building joints and skids. Paul Industries includes the anchorage details in the permit set.
What happens to reverse osmosis reject at a California ultrapure plant?
Reverse osmosis reject is usually discharged to the sanitary sewer under the wastewater agency’s industrial discharge limits, and on hard feed its concentrated salts and hardness can approach those limits as recovery rises. Reuse for cooling tower make-up or other non-critical duties is often possible. Paul Industries sets recovery and reuse with the discharge permit conditions in hand.
How much does power add to running an ultrapure water plant in California?
Pumps for reverse osmosis, polishing and loop recirculation run around the clock. At California’s 2024 industrial average of 21.53 cents per kilowatt-hour (EIA), 75 kilowatts of continuous pumping costs about $141,000 a year, compared with about $53,000 at the national average. Variable speed loop pumps and efficient high-pressure pumps cut that figure, and Paul Industries prices them against the site’s tariff.
Which loop material suits a California semiconductor R&D lab?
High-purity PVDF is the usual choice for semiconductor-grade loops because it releases very little organic carbon, metals or particles and handles ozone and hot water sanitization within its rating. Polypropylene suits many laboratory and device loops at lower cost. Paul Industries selects the material from the water specification, sanitization method and budget, and welds joints by butt-fusion or infrared methods.
How is a newly added point of use proven before it joins a live California loop?
The new section is installed, pressure tested, purged and rinsed while isolated from the main loop, then sampled for resistivity, organic carbon and particles until it meets the specification. Only then is it opened to the loop. Paul Industries also confirms that generation capacity covers the added draw at peak and records results for each new point of use.
What makes up an ultrapure water system price for a California lab or fab?
Generation capacity and quality, pretreatment for the site’s feed, loop length and points of use, loop material, analyzers, storage, seismic anchorage, reject handling, controls and turnover records all drive the price. Feedwater differences alone can change the front end noticeably between Bay Area and San Diego sites. Paul Industries gives a budget range from comparable scope, then a firm price after design review.
Who keeps a California ultrapure plant running after startup?
Yes. Paul Industries services California ultrapure plants with membrane cleaning, resin and cartridge replacement, ultraviolet lamp changes, analyzer calibration, loop sanitization and trend reviews, under a service contract or on call. Records from each visit go into the site’s water system file so audits and tool qualifications have a complete history.
Which inputs does Paul Industries need to scope a California ultrapure system?
Send a recent feedwater analysis or the utility name, the flow and quality required at each point of use, the number of users or tools, the building layout and any existing system drawings, plus the sewer discharge permit if one exists. Paul Industries returns a treatment train outline, a loop concept and a budget range.
Planning ultrapure water for a California lab, R&D center or plant?
Send a feedwater analysis or utility name, the flow and quality at each point of use, and the building layout. Call 201-450-8280 or request a quote.
