Paul Industries installs process piping in Colorado for breweries, dairies, food plants, biotech and pharmaceutical producers, refineries, utilities and data centers, designing, fabricating, welding and testing piping systems to ASME B31.3 and the other codes each service requires. Colorado adds conditions that sea-level designs miss: an atmosphere of about 12.1 psia in Denver that cuts pump suction margin, Front Range winters that freeze idle lines, and state rules that bring API 570, NFPA 30 and the tank regulations into piping work. Paul Industries is headquartered at 256 Shore Drive, Kilmarnock, Virginia, and installs piping at plants across Colorado and in all 50 states.

Request a quote or call 201-450-8280

Headquarters 256 Shore Drive, Kilmarnock, Virginia
Pump suction About 6 ft less atmospheric head in Denver than at sea level
Hot water at 180 F Atmospheric margin falls from 17.1 ft to 10.9 ft in Denver
In-service code API 570 for petroleum and chemical piping (7 CCR 1101-5)
Fuel piping NFPA 30; buried AST piping double-walled since 2011
Reviewed November 2026

What is process piping, and which codes govern it in Colorado?

Process piping is the piping that carries a plant’s products, raw materials, chemicals, utilities and waste between equipment, as distinct from the plumbing and heating piping that serves the building’s occupants. Answering what is process piping matters because the answer decides the code: ASME B31.3 covers chemical, pharmaceutical, food, petroleum and similar process plants, ASME B31.1 covers power and boiler piping, and ASME B31.9 covers building services. Colorado layers its own requirements on top of those national codes through the boiler, tank and plumbing rules.

Process piping code by Colorado service
Piping serviceDesign codeColorado layer
Chemical, food, beverage and general process pipingASME B31.3Fire and building codes adopted by the city or county
Boiler external pipingASME B31.1Adopted by rule 1-5 of 7 CCR 1101-5 and inspected with the boiler
Petroleum and chemical piping in serviceAPI 570 for inspection, repair, alteration and reratingIncorporated by rule 1-5 of 7 CCR 1101-5
Fuel transfer piping at tank systemsNFPA 30Rule 3-2 of 7 CCR 1101-14; buried piping follows the underground tank rules
Biotech and pharmaceutical product and clean utility pipingASME BPE within B31.3FDA requirements for the product; qualification records
Dairy and food contact piping3-A Sanitary Standards within B31.3Food safety rules for the product
Fuel gas and plumbing systemsFuel gas and plumbing codesState Plumbing Board licensing under C.R.S. 12-155, which defines gas piping
Chilled water, heating water and condenser waterASME B31.9 or B31.1 by pressure and temperatureMechanical code adopted by the city or county

The process piping code is chosen with the owner at the start of design, because it sets the materials, examination extent, test pressure and records for the whole job. Paul Industries writes the code basis into the line list so every spool, weld and test traces back to it. The national scope of piping work is on the process piping page; this page covers what Colorado changes.

Pump suction piping at Colorado elevation

Pump suction piping at Colorado elevation is designed with about 6 feet less atmospheric head than at sea level, and that loss comes straight out of the net positive suction head available (NPSHa) for every pump drawing from an open tank. Atmospheric pressure in Denver is about 12.1 psia against 14.7 at sea level; at the Colorado Springs weather station, 6,181 feet up, it is about 11.7 psia. Hot liquids make the problem sharper, because vapor pressure rises with temperature while the atmosphere stays the same.

Atmospheric pressure minus vapor pressure, as feet of water, for an open tank
Water temperatureSea levelDenver, 5,280 ft6,181 ft
60 F33.3 ft27.3 ft26.4 ft
140 F27.7 ft21.6 ft20.7 ft
180 F17.1 ft10.9 ft9.9 ft

The table is the starting margin before static height and suction friction are counted. At 180 degrees Fahrenheit, a hot water or CIP supply pump in Denver starts with about 10.9 feet instead of 17.1, a cut of more than a third. A suction line with an extra elbow, a partly closed valve, a strainer that loads up or a pump set a few feet higher than the tank can then push the pump into cavitation. Paul Industries calculates NPSHa at the site’s atmospheric pressure and the hottest operating temperature, then lays out suction piping short and straight, sizes it for low velocity, places strainers where they can be cleaned, and sets pumps low enough to keep a margin over the pump’s required NPSH. Where the margin is still thin, the options are a flooded suction from a raised tank, a larger suction line, a slower pump or a pump with a lower NPSH requirement.

Steam, condensate and flash at altitude

Steam and condensate piping in Colorado flashes more vapor than the same system at sea level, because condensate dropped to an atmospheric receiver settles at Colorado’s lower boiling point. Condensate leaving 100 psig steam at about 338 degrees Fahrenheit and discharged to an atmospheric receiver flashes about 13.3 percent of its mass to steam at sea level; in Denver, where the receiver sits near 202 degrees, the figure rises to about 14.2 percent. That extra flash loads vent lines, raises backpressure on trap discharges and sends more vapor out of receiver vents.

The practical response is in the piping: condensate return lines sized for two-phase flow from the trap outlet, receiver vents sized for the higher flash rate, flash recovery vessels where the low-pressure steam can be used, and pumped returns where gravity lines would flood. Pumps on condensate receivers face the same NPSH loss as other hot-liquid pumps, so receivers are raised or pumps chosen for low NPSH. Paul Industries designs steam and condensate piping with the boiler room work described on the boiler repair in Colorado page.

Freeze protection and thermal movement on Front Range piping

Front Range piping has to ride through hard freezes and wide seasonal swings, since Denver’s 1991 to 2020 normals run from a January low of 18 degrees Fahrenheit to a July high of 90, with below-zero nights about five times a year. Water-filled lines on outdoor racks, in unheated mechanical rooms and at dock doors are the usual casualties, along with instrument taps, drain legs, safety shower supplies and dead legs that see no flow. A frozen process line can split a weld or a valve body and release product when it thaws.

Paul Industries designs freeze protection into the line list: heat tracing with insulation and weather jacketing on exposed water-bearing lines, drains at low points and vents at high points so idle lines can be emptied, recirculation on lines that sit idle overnight, and freeze-protected supplies for emergency equipment. Thermal movement is checked at the same time, because a pipe rack that runs from a cold winter night to a summer afternoon in full sun grows and shrinks along its length; expansion loops, guides and anchors are placed so the movement goes where the design intends. Heat tracing design is covered on the heat tracing page.

Process piping materials by Colorado industry

Process piping materials for Colorado plants follow the product and the cleaning chemistry, and the state’s industries use nearly the full range. Breweries from the Coors brewery in Golden to Front Range craft producers run stainless product, CIP and glycol piping. In Greeley, Leprino Foods runs a cheese plant, and food processors across Weld County use 3-A sanitary piping with documented welds and CIP circuits. Agilent announced a $725 million expansion of its nucleic acid therapeutics manufacturing in Frederick in 2023, the kind of plant that runs ASME BPE tubing and clean utilities. Suncor’s Commerce City refinery, at about 98,000 barrels a day, runs carbon and alloy steel piping inspected under API 570. These plants are named as market facts only.

Typical piping materials and joining by Colorado sector
SectorMaterialsJoining and records
Brewing and distilling304 and 316L stainless tubing; glycol in stainless or carbon steelOrbital welds with borescope checks; sanitary clamps at equipment
Dairy and food processing304 and 316L stainless, 3-A finishesDocumented orbital welds, slope verification, CIP coverage records
Biotech and pharmaceutical316L electropolished tubing, ASME BPE fittingsWeld logs, borescope records, passivation, slope and dead-leg checks
Refining and chemicalCarbon steel, chrome-moly, stainless and alloys by serviceB31.3 examination, PMI where specified, API 570 inspection basis
Utilities and data centersCarbon steel, ductile iron, stainless, HDPE by serviceWelded, grooved or fused joints with pressure test records
Fuel transfer at tank systemsCarbon steel above grade; double-wall listed piping below gradeNFPA 30 testing; underground tank rule records

Sanitary systems for food, dairy and life sciences are covered in more detail on the sanitary process piping in Colorado page, and water system piping on high-purity water systems in Colorado.

Glycol and chilled water piping for Colorado cellars and process cooling

Glycol and chilled water piping carries much of the cooling load in Colorado breweries, dairies and food plants, and its design shapes how evenly every tank or heat exchanger on the loop is cooled. Fermenter jackets, bright tanks, wort coolers, cheese vats and product chillers all draw from the same supply header, so header sizing, balancing valves and control valve authority decide whether the far tank gets the same cooling as the near one. Propylene glycol at low temperature is more viscous than water, which raises pressure drop and pump power; the piping is sized for the glycol concentration and the coldest supply temperature rather than for water.

Paul Industries designs glycol loops with reverse-return or balanced headers, insulated and vapor-sealed piping to stop condensation and ice on cold lines, expansion tanks sized for the glycol volume, and air separation at the high points. Glycol pumps drawing from an open reservoir face the same reduced suction head as any other pump at altitude, so reservoirs are set to give a flooded suction. Chiller-side work connects to the chiller repair in Colorado page, and the piping is flushed, filled, balanced and documented before the cellar goes back into service.

Process piping fabrication and installation in an operating Colorado plant

Process piping fabrication for an operating Colorado plant is planned so the plant keeps running while the new system goes in. Paul Industries field-measures or laser-scans the routing, issues isometrics, prefabricates spools off site under controlled conditions, and installs them during planned outages with tie-ins isolated, blinded and locked out under the plant’s procedures. Prefabrication cuts the hours of welding inside the production area and gives each weld a cleaner environment, which matters on stainless and sanitary piping.

Testing follows the code chosen at design. Under ASME B31.3 a hydrostatic leak test is normally made at 1.5 times the design pressure, corrected for temperature, or a pneumatic test at 1.1 times where water cannot be used, with the precautions the code requires. Sensitive leak tests, initial service tests and BPE inspections apply in the services that allow or require them. Each test is recorded with the gauge pressure, medium, hold time and acceptance, and the gauge reading carries over from the fabrication site to the Colorado plant because both are relative to the atmosphere where the gauge sits.

Welding is qualified under ASME Section IX, with welding procedure specifications, procedure qualification records and welder performance records kept in the turnover package; the industrial welding services in Colorado page covers field welding in more depth. Pipe fabrication Colorado plants order as spools is supplied with heat numbers, weld maps and examination records so every joint can be traced. More on spool work is on the pipe fabrication page.

Fuel and tank farm piping under Colorado rules

Fuel and tank farm piping in Colorado follows NFPA 30 under rule 3-2 of 7 CCR 1101-14, and the rule adds specific requirements that shape the layout. Piping connected to an aboveground tank counts as suction piping only when its whole length sits higher than the tank and no pump stands between them; every other connected line is pressurized piping. Aboveground tanks with underground piping meet the underground tank rules for construction, corrosion protection, installation and release detection, and underground piping installed after April 14, 2011 is secondarily contained. Section 8-20-231 of the Revised Statutes brings refineries, tank farms and chemical plants using liquid fuels under the NFPA fire code as well.

Paul Industries routes fuel piping above grade where the site allows, so inspection and leak detection stay simple, and uses listed double-wall piping with sumps and monitoring where lines must be buried. Transfer pumps, emergency shutoff valves, solenoid valves on gravity-head dispensers and overfill protection are designed with the tank system described on the tank fabrication in Colorado page.

Compressed air, nitrogen and CO2 piping at altitude

Compressed air, nitrogen and CO2 piping at Colorado plants is sized on mass flow, because a compressor at altitude draws thinner air and delivers less mass for the same displacement. Air in Denver is roughly 85 percent as dense as at sea level, so a compressor rated in actual cubic feet per minute at its inlet delivers about 15 percent less air in standard cubic feet per minute than its sea-level rating suggests. Piping sized from nameplate figures can therefore look generous while the plant runs short of air at the far end of a header.

Paul Industries sizes compressed air headers, drops and receivers from the plant’s actual demand in standard units, checks pressure drop at peak flow, and loops headers where the layout allows so the end users see steady pressure. The dry Front Range air helps dryers but does not remove the need for them; drains, filters and dryers are placed so condensate does not reach tools and process users. Brewery CO2 and nitrogen systems get the same treatment, with regulators and relief valves set and sized at the site’s atmospheric pressure. Compressor room work ties into the boiler and utility systems on the same site.

Process piping and welding: inspection hold points

Process piping and welding are inspected at hold points agreed before work starts, so the owner sees quality at each stage rather than only at the final test. Typical hold points are receipt inspection of material against mill certificates and markings, fit-up inspection of the first welds by each welder and procedure, visual examination of completed welds, radiography or ultrasonic examination to the percentage the code and specification require, borescope inspection of sanitary and BPE welds, and the pressure test witnessed by the owner or inspector. Positive material identification is added where alloy mix-ups would be costly.

Each hold point produces a record that goes into the turnover package: material receiving reports, weld maps with welder and procedure identification, examination reports, borescope images and test packages. Paul Industries keeps those records current during the job, so a weld rejected at examination is repaired, reexamined and recorded before the line moves to testing.

How a Colorado process piping project runs, from survey to turnover
StageWhat happensWhat the owner receives
Survey and basisWalk-down or scan, code basis, design conditions, elevation and freeze reviewLine list and design basis memo
DesignRouting, stress and support checks, NPSH checks, tie-in planningP&IDs, isometrics, tie-in list
PrefabricationSpools cut, fitted, welded and examined off siteWeld maps, examination records, heat numbers
InstallationSpools set, field welds made, supports and insulation installedField weld records, support and tracing records
Testing and cleaningPressure tests, flushing, cleaning and passivation where requiredTest packages and cleaning records
Startup and turnoverTie-ins, commissioning with operations, punch list closedAs-built drawings and the indexed turnover package

Keeping Colorado process piping in service

Keeping Colorado process piping in service depends on an inspection basis that matches the service, and the state rules point petroleum and chemical plants to API 570. That code sets inspection of in-service piping, repairs, alterations and rerating, with intervals tied to corrosion rates and the consequence of a leak. Other plants follow their own maintenance programs, insurer requirements and the owner’s process safety management where federal process safety rules apply. Rule 1-11 of the Colorado boiler regulations also recommends that repairs to piping outside the boiler external piping be made by an organization with a written quality system modeled on the NBIC’s.

Paul Industries builds each new system with the information that later inspection needs: line lists with design conditions, corrosion allowances, thickness monitoring locations marked on isometrics, valve and instrument data, and test records. When a line corrodes, cracks or leaks, Paul Industries repairs or replaces it to the original code, records the repair, and reviews the material choice so the replacement lasts.

What does process piping in Colorado cost?

The cost of process piping in Colorado is driven by line sizes and lengths, materials and wall thickness, joint type and examination extent, the number of valves, instruments and supports, insulation and heat tracing, access and elevation inside the plant, the number of tie-ins and the outage windows available. Sanitary and BPE systems cost more per foot than carbon steel utility piping because of materials, orbital welding, borescope inspection and documentation. Work inside an operating plant adds isolation, permits and phased tie-ins.

On state work, a Colorado agency contract worth $500,000 or more carries prevailing wage rates under the procurement code, sections 24-92-202 and 24-92-203. Paul Industries prices from P&IDs, a line list or a walk-down, giving a budget range from comparable systems first and a firm price once routing and specifications are agreed.

Who installs process piping in Colorado?

Paul Industries installs process piping in Colorado, from single-line tie-ins to complete plant piping packages with pumps, valves, instruments, insulation and controls. Plants comparing process piping contractors and process piping companies get design, fabrication, installation, testing and turnover under one contract, with industrial piping Colorado plants need in Denver, Aurora, Commerce City, Golden, Boulder, Longmont, Greeley, Colorado Springs, Pueblo and Grand Junction handled the same way. Colorado is part of the Southwest region Paul Industries serves, and the company takes work in all 50 states. Its headquarters-state piping work is on the process piping in Virginia page, and plants with other sites can compare process piping in Texas and process piping in California.

Process piping services in Colorado from Paul Industries

Paul Industries designs, fabricates, supplies, installs, tests and maintains process piping for Colorado plants. Process piping services run from supply-only prefabricated spools to design-build packages and complete installations with supports, insulation, tracing, instruments and startup. Once based in northern New Jersey and then Pennsylvania, the company today runs Colorado piping work from its Kilmarnock, Virginia headquarters. Piping often comes with tanks, vessels and utilities, all listed on the Colorado project services page. Send the P&IDs or a sketch, line list, design conditions, materials, site elevation and outage windows, and request a quote.

Standards referenced: ASME B31.3 Process Piping · ASME B31.1 Power Piping · ASME B31.9 Building Services Piping · ASME BPE · API 570 · NFPA 30 · ASME Section IX · 7 CCR 1101-5 and 7 CCR 1101-14 · 3-A Sanitary Standards

Frequently asked questions

Which industrial process piping contractors work at Colorado refineries and chemical plants?

Paul Industries is one of the industrial process piping contractors working at Colorado refineries and chemical plants, installing carbon steel, chrome-moly, stainless and alloy piping to ASME B31.3. Petroleum and chemical piping in service is inspected, repaired, altered and rerated under API 570, which Colorado’s boiler and pressure vessel rules incorporate. Paul Industries plans the work around turnarounds and the plant’s safe work procedures.

Who are the stainless steel process piping contractors for Colorado biotech and food plants?

Paul Industries is one of the stainless steel process piping contractors for Colorado biotech, dairy, brewing and food plants, installing 304 and 316L tubing with orbital welds, borescope inspection, slope checks and passivation. Biotech systems follow ASME BPE and food systems 3-A practice. Each weld is logged and traceable, and the turnover package supports the plant’s qualification or food safety program.

Who handles process piping Denver food and beverage plants need during a shutdown?

Paul Industries handles process piping for Denver food and beverage plants during shutdowns, prefabricating spools off site and installing them during the outage window with isolated, blinded and locked-out tie-ins. Sanitation and restart steps are planned with plant operations, and pressure tests and cleaning records are completed before production resumes. Call 201-450-8280 with the shutdown dates and P&IDs.

Who are the process piping contractors Colorado Springs and Pueblo plants use?

Process piping contractors Colorado Springs and Pueblo plants use include Paul Industries, which installs process piping Colorado Springs manufacturers, utilities and campuses need, along with Pueblo industrial and energy sites. Colorado Springs sits near 6,200 feet, where an open tank supplies about 7 feet less atmospheric head than at sea level, so pump suction piping is checked against that figure during design.

Why do pumps cavitate on hot water lines in Colorado plants?

Pumps cavitate on hot water lines in Colorado because the atmosphere supplies less suction head while hot water has a high vapor pressure. At 180 degrees Fahrenheit, an open tank in Denver gives about 10.9 feet of margin before static height and friction, against 17.1 feet at sea level. Paul Industries corrects the problem by shortening and enlarging suction piping, raising the source tank, lowering the pump or reselecting it.

What process piping code applies to a Colorado brewery?

Brewery product, CIP and utility piping is generally designed to ASME B31.3, with sanitary practice for product contact surfaces, ASME B31.1 for boiler external piping and the fuel gas code for gas lines. The city or county’s adopted mechanical, fire and building codes apply to the installation. Paul Industries sets the code basis on the line list so materials, welds and tests follow it consistently.

Does Colorado require secondary containment for buried fuel piping?

Rule 3-2 of 7 CCR 1101-14 requires aboveground tanks with underground piping to meet the underground tank rules, including secondary containment for underground piping installed after April 14, 2011, along with corrosion protection and release detection. Paul Industries routes fuel piping above grade where possible and uses listed double-wall piping with sumps and monitoring where lines must be buried.

How is process piping tested before startup in Colorado?

Process piping is tested to its design code before startup: ASME B31.3 normally calls for a hydrostatic leak test at 1.5 times design pressure, corrected for temperature, or a pneumatic test at 1.1 times with added precautions. Sanitary and BPE systems add borescope, slope and cleaning checks. Paul Industries records gauge pressure, medium, hold time and acceptance for each test package.

What does pipe fabrication Denver plants order as prefabricated spools include?

Pipe fabrication Denver plants order as spools includes isometric drawings, cut and fitted pipe with flanges or ends prepared for field joints, welds made under qualified procedures, examination to the code and specification, heat numbers and weld maps for traceability, and cleaning, capping and labeling for delivery. Paul Industries also installs the spools and completes the field joints and tests.

How is industrial piping Denver plants run outdoors protected from freezing?

Outdoor industrial piping in Denver is protected with heat tracing, insulation and weather jacketing on water-bearing lines, drains at low points and vents at high points, recirculation on lines that sit idle, and freeze-protected supplies for safety showers and fire equipment. Denver sees below-zero nights about five times a year. Paul Industries designs that protection into the line list and tests the tracing circuits before winter.

Who installs process piping fort collins and Greeley food plants depend on?

Paul Industries installs process piping for Fort Collins and Greeley food plants, breweries and campuses, including stainless product and CIP piping, glycol and refrigeration-adjacent utilities, steam and condensate, and water treatment piping. Weld County food plants run long production days, so installation is phased into planned sanitation and shutdown windows with documented tie-ins.

Which piping contractors denver data centers and campuses use for chilled water?

Data centers and campuses in the Denver area use piping contractors such as Paul Industries for chilled water, condenser water, heating water and process cooling piping, built to ASME B31.9 or B31.1 by service and the city’s adopted mechanical code. Work in live facilities is staged with valves and bypasses so cooling stays online. Paul Industries designs, installs, flushes, tests and documents those systems.

What process piping materials suit a Colorado biotech plant's clean utilities?

Clean utilities in a biotech plant typically use 316L stainless tubing with ASME BPE fittings, electropolished where the specification calls for it, orbital welded and passivated. Clean steam lines are sloped and trapped for drainage, and water for injection loops are designed without dead legs. Paul Industries supplies the weld logs, borescope records and passivation documentation that qualification needs.

How much flash steam does condensate make in a Denver plant?

Condensate leaving 100 psig steam and dropped to an atmospheric receiver flashes about 14.2 percent of its mass to steam in Denver, compared with about 13.3 percent at sea level, because the receiver sits near 202 degrees Fahrenheit instead of 212. Paul Industries sizes trap discharge lines, receiver vents and flash recovery vessels for the higher flash rate.

Are Colorado state projects for process piping subject to prevailing wage?

When a Colorado state agency awards a piping contract worth $500,000 or more, sections 24-92-202 and 24-92-203 of the procurement code set prevailing wage rates for it. Municipal, county and school district contracts, and work paid with federal funds, follow other wage rules. Paul Industries confirms the wage basis with the owner before pricing.

What records does a Colorado plant receive with new process piping?

A Colorado plant receives the line list, as-built isometrics and P&IDs, material certificates and heat numbers, welding procedures and welder qualifications, weld maps and examination records, pressure test packages, cleaning and passivation records where applicable, valve and instrument data sheets and the heat tracing schedule. Paul Industries indexes the package by line number.

Can Paul Industries fix an existing piping system that keeps cavitating pumps at altitude?

Paul Industries fixes existing systems with cavitating pumps by measuring suction pressure and temperature, recalculating NPSHa at the site’s atmospheric pressure, and then correcting the suction piping, strainer, tank elevation or pump selection. Common changes include larger and shorter suction lines, eccentric reducers, removing elbows near the pump inlet and raising the source tank. The fix is tested and recorded.

Adding or replacing process piping at a Colorado plant?

Send the P&IDs or a sketch, line list, design conditions, materials, site elevation and outage windows. Call 201-450-8280 or request a quote.