Paul Industries designs, builds, installs and services ultrapure water systems in Rhode Island, from pretreatment and reverse osmosis through electrodeionization, polishing, ultraviolet treatment and distribution loops, for biologics and pharmaceutical plants, hospital and university laboratories, electronics and precision manufacturers, and power and process boilers. Every Rhode Island system starts from the water the building receives, and that differs sharply across the state: chlorinated, high pH, phosphate dosed reservoir water from Scituate, a Kent County blend that shifts between surface water and wells with the seasons, and separate reservoir and well supplies in Pawtucket, Woonsocket, Newport and South County. Paul Industries designs the treatment train around the actual feed.
Request a quote or call 201-450-8280
Ultrapure water systems in Rhode Island: where they run and what they feed
Ultrapure water systems in Rhode Island supply biologics and pharmaceutical manufacturing, research and clinical laboratories, electronics, optics and precision manufacturing, and high pressure boilers, each with its own purity target. Amgen’s West Greenwich campus runs upstream cell culture manufacturing; Brown University, the University of Rhode Island and the hospitals of Providence run research and clinical labs; and manufacturers in the Quonset Business Park, the Blackstone Valley and the Route 95 corridor use purified water for rinsing, coating, cooling and boiler makeup. These are market facts about where purified water is used in Rhode Island.
The national overview of grades, analyzers and loop materials is on the ultrapure water systems page. This page goes into the Rhode Island specifics: what each public water supply sends into a plant, how free chlorine, lime and orthophosphate in Providence Water shape the pretreatment, the state’s PFAS limit, sewer discharge rules for reject water, the boiler and pressure vessel law as it applies to sanitizable tanks, and the cost of running a plant on Rhode Island power. Rinse and recovery water for plating and metal finishing lines is covered separately on the Rhode Island metal finishing water page.
Is Providence water hard or soft?
Providence Water starts with soft reservoir water from the Scituate complex in a 93 square mile, mostly forested watershed, then adds lime for pH adjustment and corrosion control and doses orthophosphate, so the water reaching a plant is low in alkalinity, held at a high pH and carries phosphate and the calcium the lime contributes. Providence water hardness is therefore modest rather than high, and the figure that matters for design is the one in the current Providence RI water quality report or, better, a full laboratory analysis of a sample drawn at the plant’s own tap. The utility serves about 600,000 people, around 60 percent of the state, directly and through wholesale connections to East Providence, Cranston, Warwick, Lincoln, Smithfield, Bristol County and Kent County systems.
Three other features of the finished water matter more to an ultrapure train than hardness does. The disinfectant is free chlorine, with a 2025 running annual average of 0.41 milligrams per liter and readings up to 0.72 in the East Providence system. Turbidity is very low, averaging under 0.1 NTU in 2025. Disinfection byproducts are present, with total trihalomethanes averaging 64.8 micrograms per liter at the highest East Providence location, and those volatile organics behave differently from other organics in treatment.
| Parameter | Reported value or practice | Effect on the treatment train | Design response |
|---|---|---|---|
| Disinfectant | Free chlorine, 0.41 mg/L average, 0.17 to 0.72 range | Oxidizes polyamide RO membranes | Carbon filtration or sodium bisulfite dosing with an ORP or chlorine monitor ahead of the RO |
| pH control | Lime added for pH adjustment and corrosion control | High pH favors scaling in the RO concentrate | Antiscalant chosen for calcium salts, recovery set from a scaling projection |
| Corrosion inhibitor | Orthophosphate since January 2021 | Calcium phosphate can precipitate as water warms and concentrates | Phosphate specific antiscalant, conservative recovery, regular cleaning in place |
| Trihalomethanes | 64.8 micrograms per liter, highest location average | Small neutral organics pass RO and raise TOC | 185 nanometer ultraviolet oxidation and polishing resin, TOC analyzer on the loop |
| Turbidity | Under 0.1 NTU average | Low particle load on cartridge filters and membranes | Multimedia filtration sized for upsets rather than daily load |
| Sodium and fluoride | 11.6 mg/L and 0.77 mg/L | Both rejected well by RO | Normal RO and EDI design; fluoride tracked where the product is sensitive |
| PFAS | None detected in 2025 sampling | No present load from the supply | RO reject handling planned in case future feed results change |
Free chlorine, lime and orthophosphate ahead of reverse osmosis
Free chlorine in Rhode Island’s largest water supply means every ultrapure train fed from it needs a reliable dechlorination step, because thin film polyamide RO membranes lose rejection permanently once chlorine attacks them. Paul Industries uses activated carbon beds sized for the chlorine load and contact time, or sodium bisulfite injection where carbon would become a breeding ground for bacteria, and installs an oxidation reduction potential or chlorine monitor that stops the RO before treated water with residual chlorine reaches the membranes.
The phosphate and lime chemistry calls for care at the other end of the membrane. An EPA research dataset on Providence pipe scale describes a calcium phosphate solid that formed as an unintended result of the high pH orthophosphate strategy, appearing above about 2 milligrams per liter as phosphate and increasing with water age and temperature. An RO concentrate stream holds the same ions at several times feed strength and often runs warm in a plant room, so Paul Industries runs a scaling projection on the actual feed analysis, selects an antiscalant proven against calcium phosphate, sets recovery conservatively, and fits clean in place connections so membranes are cleaned on a schedule rather than after a fouling event. Adjusting pH ahead of the membranes with acid is another lever, weighed against the extra carbon dioxide that EDI then has to remove.
Kent County feed and ultrapure water system design through the seasons
The Kent County Water Authority, which serves about 88,780 people, buys roughly 75 percent of its water from Providence Water in summer and about 40 percent in winter, with the rest pumped from wells in the Hunt River aquifer in East Greenwich and the Mishnock aquifer in Coventry. A plant on that system therefore receives treated reservoir water for part of the year and a blend weighted toward groundwater for the rest, and groundwater commonly carries different hardness, silica, iron and dissolved carbon dioxide than surface water. West Greenwich is also among the communities that receive Providence Water through wholesale connections.
For a Kent County ultrapure water system design, Paul Industries asks for analyses from both seasons, or samples the feed in summer and winter before the design is fixed, and sizes softening, antiscalant dosing, RO recovery and degassing for the worse of the two. A Kent County water quality report gives the starting point, but the blend at a particular meter depends on where the plant sits in the distribution system, which is why a sample from the building itself carries more weight.
Feed water across the rest of Rhode Island
Feed water across the rest of Rhode Island comes from a set of separate utilities with their own sources, so an ultrapure plant in Pawtucket, Woonsocket, Newport, South Kingstown or Quonset starts from a different water than one in Providence.
| Supply | Area served | Source | Points for the treatment train |
|---|---|---|---|
| Providence Water | Providence and neighboring cities, plus wholesale supply to more than a dozen communities | Scituate Reservoir complex, Philip J. Holton plant | Free chlorine, high pH, orthophosphate, trihalomethanes |
| Kent County Water Authority | Kent County communities, about 88,780 people | Providence Water blended with Hunt River and Mishnock aquifer wells | Seasonal swing between surface water and groundwater |
| Pawtucket Water Supply Board | Pawtucket, Central Falls and Valley Falls in Cumberland | Abbott Run reservoirs, including Diamond Hill, plus eight active wells | Mixed surface and groundwater; design on a current analysis |
| Woonsocket Water Division | Woonsocket and parts of North Smithfield | Three reservoirs, Jillson Avenue plant online since July 2021 | Newer treatment plant; confirm disinfectant and organics with current data |
| Newport Water | Newport, with wholesale to Portsmouth and Naval Station Newport | Nine surface reservoirs on Aquidneck Island and in Little Compton and Tiverton | Surface water organics and seasonal changes; TOC removal planned with care |
| Veolia Water Rhode Island | Parts of South Kingstown and Narragansett | Wells in the Mink Brook aquifer | Groundwater chemistry; silica and hardness checked before RO design |
| Quonset Development Corporation | Quonset Business Park, North Kingstown | The park’s own water system | Analysis from the park utility; discharge to the park’s wastewater system |
Plants on private wells, common in the western and southern parts of the state, need a full analysis including iron, manganese, silica, hardness and bacteria, and often a pressure filter and softener ahead of the RO. The same sampling discipline applies at every site: Paul Industries designs from water drawn at the point of use rather than from a citywide average.
Rhode Island PFAS regulations and the ultrapure train
Rhode Island PFAS regulations set a drinking water limit of 20 parts per trillion for the combined total of six compounds, PFOS, PFOA, PFHxS, PFNA, PFHpA and PFDA, in amendments to the state’s Public Drinking Water Regulations that took effect on September 18, 2024. Public water systems above that level notify customers and enter an agreement with the Department of Health to reduce it. The East Providence system, supplied by Providence Water, reported no PFAS detected in its 2025 sampling.
When a buyer checks PFAS in drinking water, Rhode Island results come from each supplier’s annual report, and for an ultrapure plant those results matter in two ways. Reverse osmosis rejects these compounds well, so the product water is protected, but whatever enters with the feed leaves in the RO reject at higher concentration, which can matter to the sewer authority receiving it. Plants on wells or on supplies with detections can add granular activated carbon or ion exchange ahead of the RO to remove PFAS before it reaches the reject stream. Paul Industries reviews the supplier’s PFAS results with the feed analysis and designs the reject handling to match.
Ultrapure water for cell culture and biologics manufacturing
Ultrapure water for cell culture in Rhode Island biologics plants and research labs is usually one of three grades: USP Purified Water for buffer and media preparation where the process allows it, Water for Injection where the product or its contact surfaces demand it, and laboratory Type I ultrapure water for analytical work and small scale culture. The limits that separate those grades are summarized below, and the grade a user names decides the materials, sanitization and records of the whole system.
| Grade | Where it is used | Defining limits | Usual treatment route |
|---|---|---|---|
| USP Purified Water | Buffer and media preparation where the process permits, equipment cleaning | Stage 1 conductivity 1.3 microsiemens per centimeter at 25 C; TOC 500 ppb | Pretreatment, RO and EDI feeding a sanitized loop |
| Water for Injection | Parenteral products and final rinse of product contact parts | Purified Water chemistry plus endotoxin below 0.25 EU per milliliter | Distillation, or membrane production where permitted, on a hot loop |
| ASTM D1193 Type I | Analytical chemistry, molecular work and small scale culture | 18.0 megohm centimeters minimum; TOC no higher than 50 micrograms per liter | Central RO and EDI with a point of use polisher at the bench |
| RO permeate | Rinsing, humidification and boiler makeup | A few to tens of microsiemens per centimeter, depending on feed | Dechlorination, antiscalant and single or double pass RO |
A plant that makes Purified Water or WFI follows those compendial tests, designs the loop to ASME BPE with sanitary fittings, drainable slopes and orbital welds, and qualifies the system before production. Paul Industries carries that qualification through the protocols described on the validation and commissioning in Rhode Island page, and the clean utilities that sit beside the water system are covered on the CIP and SIP systems in Rhode Island page.
Is ultrapure water sterile?
Ultrapure water is defined by its ionic, organic and particle purity, and sterility is a separate property, so ultrapure water from a well run loop has very low bacteria counts but is not sterile unless it is produced and handled as sterile water. Bacteria and endotoxin are kept low by ultrafiltration, ultraviolet treatment, continuous circulation, and hot water or ozone sanitization of the loop. Where sterility is required, as for sterile water products, the water is sterilized and packaged under a validated process. Paul Industries designs loops with the sanitization method and microbial monitoring points chosen for the grade each user needs.
Ultrapure water vs RO water
Ultrapure water vs RO water is a question of how far treatment goes. A reverse osmosis unit typically removes 95 to 99 percent of dissolved salts and most organics and microbes, leaving permeate in the range of a few to tens of microsiemens per centimeter depending on the feed. Ultrapure water treatment carries that permeate through electrodeionization or ion exchange, ultraviolet oxidation, polishing resin and final filtration to reach 18 megohm centimeters and low part per billion organics. RO water suits rinsing, humidification and boiler makeup in many plants; ultrapure water serves analytical labs, cell culture, electronics and coating processes.
A laboratory ultrapure water system for Rhode Island research buildings
A laboratory ultrapure water system in a Rhode Island research building is usually a central RO and EDI plant producing pure water to a building loop, with point of use polishers at each lab producing Type I water at the bench. The central plant handles the feed chemistry described above once for the whole building, and the polishers deliver the final quality where the water is used. Paul Industries sizes the central plant for the building’s peak draw, runs the loop in materials that suit the quality and sanitization method, and sets the polishers so each lab gets the grade its work requires.
An ultrapure water system for laboratory buildings in an occupied university or hospital needs a plan for adding labs, isolating loop sections and keeping water quality during changes. Paul Industries installs isolation valves and sample points at each floor branch, so a new lab connects without draining the loop, and flushes and tests each addition before it opens to the rest of the system.
Ultrapure water system: semiconductor, optics and electronics users
Manufacturers that need ultrapure water for semiconductor, optics or electronics rinsing follow the same central plant and loop layout at larger scale, with double pass RO or RO with EDI, 185 nanometer ultraviolet oxidation, polishing resin, ultrafiltration and continuous resistivity, TOC and particle monitoring on a polymer loop.
Sanitizable tanks under Rhode Island’s boiler and pressure vessel law
Rhode Island’s boiler and pressure vessel law exempts storage vessels at 15 psig or less, which covers atmospheric ultrapure storage tanks with a nitrogen blanket, but pressurized hot water vessels larger than 120 gallons fall within the law and need a permit to install. The exemption for water vessels stops at 120 gallons, 300 psi and 180 degrees Fahrenheit, so a large pressurized tank held at 80 degrees Celsius for hot water sanitization sits inside the law on its size alone, and indirectly heated water vessels lose their exemption above 200,000 Btu per hour, 210 degrees or 120 gallons. Paul Industries specifies those vessels to ASME Section VIII with their data reports and arranges the boiler unit’s permit before installation. Custom vessels are covered on the pressure vessel fabrication in Rhode Island page and storage tanks on the tank fabrication in Rhode Island page.
Where does RO reject water go at a Rhode Island plant?
RO reject, EDI concentrate and ion exchange regenerant from a Rhode Island ultrapure plant go to the sewer under the rules of the authority that receives them, which in metropolitan Providence and the Blackstone Valley is the Narragansett Bay Commission. The Commission serves about 394,000 residents and 7,700 businesses, operates the Field’s Point and Bucklin Point treatment facilities, and runs a pretreatment program that issues wastewater discharge permits to industrial users. Newport runs its own industrial pretreatment program, and the Quonset Business Park has its own wastewater system.
Reject water from a Providence Water feed carries concentrated calcium, phosphate, sodium and the antiscalant, and regenerant from ion exchange swings in pH unless it is neutralized. Paul Industries designs neutralization for regenerant streams, provides flow and chemistry data for the discharge application, and evaluates reusing RO reject as cooling tower makeup or for other plant uses where its chemistry allows, which cuts both the sewer load and the plant’s water bill.
How much does Rhode Island electricity add to running an ultrapure plant?
Electricity for Rhode Island industry cost an average 19.70 cents per kilowatt hour in 2024, the EIA reports, where the US figure was 8.13 cents, and an ultrapure plant draws power around the clock for RO pumps, loop pumps, EDI stacks, ultraviolet lamps and, on hot sanitized systems, heaters. A plant drawing an average 40 kilowatts uses about 350,400 kilowatt hours a year, which costs roughly $69,029 at the Rhode Island average and about $28,488 at the national one. Variable speed loop pumps, high efficiency RO pumps, energy recovery on larger RO trains and heat recovery from sanitization cycles pay back faster here, and Paul Industries includes the energy figures with each design option.
Who installs ultrapure water systems in Rhode Island?
Paul Industries installs ultrapure water systems in Rhode Island for biologics and pharmaceutical plants, hospitals, universities, research labs, electronics and precision manufacturers and process plants, in Providence, Cranston, Warwick, West Greenwich, East Greenwich, Pawtucket, Woonsocket, North Kingstown, Newport, South Kingstown and the rest of the state. Paul Industries has its headquarters at 256 Shore Drive in Kilmarnock, Virginia, came there from earlier bases in northern New Jersey and then Pennsylvania, and builds water systems across New England and in all 50 states.
Owners can take an ultrapure plant from Paul Industries as a supply-only skid with its factory test records, as design-build from feed analysis through qualification, or as complete installation to an engineer’s design, with distribution piping on the process piping in Rhode Island scope and service after startup. The same service in the headquarters state is described on the ultrapure water systems in Virginia page, and other New England feeds are compared on the Massachusetts and Connecticut pages.
Ultrapure water system price in Rhode Island: what moves it
An ultrapure water system price in Rhode Island is set by the flow and peak draw, the grade required, the feed water and its pretreatment, the loop length and material, the sanitization method, redundancy, the analyzer package and the documentation and qualification the user needs. A point of use polisher for one lab is a small purchase. A central RO and EDI plant with a stainless or PVDF loop serving a research building is a substantial project, and a compendial water system for a biologics plant, with sanitary construction and full qualification, sits above that. Feed chemistry adds its own lines: dechlorination and phosphate tolerant antiscalant on Providence Water, seasonal design on Kent County water, and iron and silica removal on wells.
Paul Industries gives a budget range from comparable systems once it knows the grade and flow, then a firm price after the feed analysis and site review. Operating cost is shown alongside, with membranes, resin, lamps, filters, chemicals and electricity at Rhode Island rates, so the owner sees the full cost of the water.
Rhode Island ultrapure water projects with Paul Industries
Paul Industries designs, fabricates, installs, starts up, qualifies and services ultrapure water systems across Rhode Island: dechlorination and pretreatment matched to the feed, RO, EDI and polishing trains, ultraviolet and ultrafiltration, storage, sanitizable distribution loops, analyzers and the records each user needs. The design starts from a sample of the building’s own water and accounts for the state’s PFAS limit, sewer authority rules and power prices. To price a plant, send the grade, the flow, the feed source and the building, and request a quote. The full range of Paul Industries work in the state is listed on the Rhode Island page.
Standards referenced: ASTM D1193 · USP <645> · USP <643> · ASME BPE · ASME B31.3 · Rhode Island Public Drinking Water Regulations (PFAS MCL) · R.I. Gen. Laws Chapter 28-25, boiler inspection and pressure vessels · Narragansett Bay Commission pretreatment rules · ISPE Baseline Guide, Water and Steam Systems
Frequently asked questions
Which contractor builds ultrapure water systems for labs and hospitals in Providence?
Paul Industries builds ultrapure water systems for laboratories, hospitals and research buildings in Providence, from central RO and EDI plants to building loops and point of use polishers. Systems on Providence Water feed include chlorine removal ahead of the membranes and an antiscalant suited to the lime and orthophosphate chemistry. Labs are added to running loops through isolation valves without draining the system.
Does Paul Industries install ultrapure water for biologics plants in West Greenwich and Kent County?
Paul Industries installs ultrapure water, Purified Water and WFI systems for biologics and pharmaceutical plants in West Greenwich, East Greenwich, Warwick and Coventry. Feed water in parts of Kent County shifts between Providence Water and groundwater with the season, so the pretreatment is designed from analyses taken in both summer and winter, and the finished system is qualified to the plant’s protocols.
Who builds purified water systems for plants in Pawtucket, Woonsocket and the Blackstone Valley?
Paul Industries builds RO, EDI and ultrapure water systems for manufacturers, labs and process plants in Pawtucket, Central Falls, Lincoln, Cumberland and Woonsocket. Each of those communities has its own water supplier and source, so the design starts from a current analysis of the building’s feed. Reject and regenerant discharge in this area is arranged under the Narragansett Bay Commission’s pretreatment program.
Does Paul Industries take ultrapure water projects at Quonset, in Newport and in South County?
Paul Industries takes ultrapure water projects at the Quonset Business Park, in Newport and Middletown, and in South Kingstown, Narragansett and Westerly. Quonset plants use the park’s own water and wastewater systems, Newport plants start from treated reservoir water, and South County plants often draw from wells, so each pretreatment train is designed from that site’s analysis.
Does Providence Water use chlorine or chloramine?
Providence Water disinfects with free chlorine, and the 2025 East Providence report shows a running annual average of 0.41 milligrams per liter with readings from 0.17 to 0.72. Free chlorine damages polyamide RO membranes, so an ultrapure plant on this supply needs carbon filtration or sodium bisulfite dosing with a monitor that stops the RO if chlorine breaks through. Paul Industries sizes that step for the peak chlorine level.
How does orthophosphate in Providence Water affect an RO system?
Orthophosphate, added since January 2021 along with lime for pH control, raises the risk of calcium phosphate scale in the RO concentrate, especially as water warms and concentrates. EPA research on Providence pipe scale found calcium phosphate forming above about 2 milligrams per liter as phosphate. Paul Industries runs a scaling projection on the actual feed, selects a suitable antiscalant and sets recovery and cleaning intervals to match.
Where can a plant find the Providence RI water quality report, and is it enough for design?
Providence Water and the wholesale systems it supplies each publish an annual water quality report, and the 2025 reports cover disinfectant, byproducts, sodium, fluoride, turbidity and PFAS. Those reports list regulated results rather than the full ionic analysis an RO design needs, such as calcium, magnesium, alkalinity, silica and phosphate. Paul Industries uses the report as a starting point and adds a full analysis of a sample from the building.
What is Rhode Island's PFAS limit for drinking water?
Rhode Island’s limit is 20 parts per trillion for the sum of PFOS, PFOA, PFHxS, PFNA, PFHpA and PFDA, in Public Drinking Water Regulations that took effect on September 18, 2024. Systems above it notify customers and agree a reduction plan with the Department of Health. RO removes these compounds from product water, and Paul Industries plans the reject stream and any pre-removal step around the feed’s PFAS results.
Which loop material suits a Rhode Island biologics or lab ultrapure system?
Electropolished 316L stainless steel with orbital welds suits compendial Purified Water and WFI loops that are hot water or steam sanitized, while PVDF and other high purity polymers suit ambient ultrapure loops in labs and electronics plants where metal ions must stay very low. Paul Industries chooses the material from the grade, the sanitization method and the user’s documentation requirements.
Do hot water sanitized storage tanks need a Rhode Island boiler unit permit?
A pressurized water tank larger than 120 gallons, or one operating above 180 degrees Fahrenheit, falls within Rhode Island’s boiler and pressure vessel law and needs a permit to install, while atmospheric tanks at 15 psig or less are exempt. Pressure-rated hot water sanitized storage tanks above that size need the permit. Paul Industries supplies them to ASME Section VIII and arranges the permit with the boiler unit.
Does RO reject from a Rhode Island ultrapure plant need a sewer discharge permit?
RO reject, EDI concentrate and neutralized regenerant go to the sewer under the authority that receives them, such as the Narragansett Bay Commission in metropolitan Providence and the Blackstone Valley, which issues wastewater discharge permits through its pretreatment program. Newport and the Quonset Business Park run their own systems. Paul Industries provides the flow and chemistry data each application needs and designs neutralization where required.
Can RO reject water be reused at a Rhode Island plant?
RO reject can often be reused as cooling tower makeup, for scrubber or floor washdown water, or blended into non-critical uses, provided its concentrated calcium, phosphate and antiscalant suit the receiving system. On Providence Water feed, phosphate in the reject needs checking against the tower’s treatment program. Paul Industries evaluates reuse during design, since it lowers both water purchases and sewer charges.
What does an ultrapure water system for semiconductor or electronics work need in Rhode Island?
Electronics, optics and precision manufacturers need water at 18 megohm centimeters or better with TOC in low parts per billion and very low particles and metals. In Rhode Island that means dechlorination and phosphate tolerant pretreatment, double pass RO or RO with EDI, 185 nanometer ultraviolet oxidation for the trihalomethanes in surface supplies, polishing resin, ultrafiltration and continuous monitoring on a polymer loop.
How much electricity does an ultrapure water plant use in Rhode Island?
Electricity use depends on flow, RO pressure, loop size and sanitization method. A plant drawing an average 40 kilowatts uses about 350,400 kilowatt hours a year, about $69,029 when priced at 19.70 cents, the state’s 2024 industrial average, compared with about $28,488 at the national average. Paul Industries reduces that draw with variable speed pumps, efficient RO pumps and heat recovery on hot sanitized loops.
Should a Rhode Island ultrapure plant have two RO trains?
Two RO trains, each able to carry the load or a large share of it, let one train be cleaned or repaired while the other runs, which matters for biologics and lab users who cannot stop drawing water. On Providence Water feed, where phosphate scaling calls for regular membrane cleaning, redundancy also keeps cleaning on schedule. Paul Industries prices single and redundant designs so the owner sees the difference.
What does service on a Rhode Island ultrapure water plant include after startup?
Service covers monitoring review, membrane cleaning and replacement, carbon and resin changes, EDI stack checks, ultraviolet lamp and sleeve replacement, filter changes, analyzer calibration, loop sanitization and records for quality teams. Paul Industries schedules RO cleaning around the scaling behavior of the feed at each site and adjusts dechlorination as chlorine levels change through the year.
Does Paul Industries sell ultrapure water skids to Rhode Island plants as supply-only packages?
Paul Industries supplies pretreatment, RO, EDI and polishing skids as supply-only packages, factory tested and delivered with drawings, test records and operating instructions, and also offers design-build and complete installation for the whole plant and loop. Owners often start supply-only for one skid and add installation, qualification and service as the project grows.
Which details does Paul Industries need to price an ultrapure water system in Rhode Island?
Send the water grade and its specification, average and peak flow, the number of use points and loop length, the sanitization method, the water supplier or well, any feed analysis on hand, the building and its plant room, and the documentation or qualification required. Paul Industries returns a budget range from comparable systems, then a firm price after the feed sample and site review.
Need ultrapure water at a Rhode Island plant or lab?
Send the grade, flow, use points, water supplier and any feed analysis you have. Call 201-450-8280 or request a quote.
