Paul Industries provides pressure vessel fabrication in Rhode Island for biologics, defense supply, film, finishing, food and utility plants, designing and building ASME Section VIII air receivers, process vessels, clean utility vessels, separators and exchanger shells. Rhode Island regulates unfired pressure vessels under the same statute as boilers, R.I. Gen. Laws Chapter 28-25, and its amended rule of December 24, 2025 requires construction to the 2025 ASME code with a National Board number on every vessel that needs a data report. Paul Industries builds each vessel to those requirements and delivers the records the Boiler Unit and the plant’s inspector work from.

Request a quote or call 201-450-8280

Headquarters 256 Shore Drive, Kilmarnock, Virginia
State law R.I. Gen. Laws 28-25 covers unfired pressure vessels
Construction ASME BPVC 2025, National Board number and data report
In-service inspection Every three years, internal where construction permits
Pressure floor Vessels at 15 psig or less are exempt
State certificate fee $45 per vessel every three years
Reviewed November 2026

What must pressure vessel fabrication in Rhode Island deliver before the first certificate?

Pressure vessel fabrication in Rhode Island must deliver a vessel designed, built, inspected and stamped to the 2025 edition of the ASME Boiler and Pressure Vessel Code, registered with the National Board, and documented with a Manufacturer’s Data Report signed by the manufacturer’s representative and a National Board commissioned inspector. Rule 2.5.1 has that report filed with the Rhode Island chief inspector through the National Board, so the state has the vessel’s construction record before the unit reaches the site. Every regulated vessel is also registered with the Department of Labor and Training.

The statute forbids erecting any vessel in Rhode Island unless it is built and fitted with safety devices to the ASME code. Whoever installs a new or second-hand vessel applies first to the Boiler Unit for a permit to install, and the state issues a certificate once satisfied by inspection or other evidence that the vessel complies. At the first inspection the inspector applies a state serial number, and a vessel too thin to stamp carries the number on a corrosion resistant tag.

From purchase order to operating certificate for a Rhode Island vessel
StageRhode Island requirementWhat Paul Industries delivers
DesignASME BPVC 2025, Section VIII Division 1 or 2Calculations, drawings, material list and relief device basis for owner review
ConstructionBuilt, inspected and stamped to the 2025 code (rule 2.5.1)Fabrication to approved weld procedures, examination and hydrostatic or pneumatic test
RegistrationNational Board number; data report filed with the chief inspector through the National BoardNameplate data and signed data report in the turnover package
InstallationPermit to install from the Boiler Unit before setting (28-25-10(b))Permit application data, setting, anchoring, piping and relief discharge
First inspectionAuthorized inspector; state serial number applied (rule 2.5.23)Vessel opened or presented as the inspector directs, stamping left exposed
CertificateIssued by the division, states the allowed pressure, posted (28-25-11)Startup records tied to the certificate pressure

Which vessels does Rhode Island exempt from its pressure vessel laws?

Rhode Island exempts two groups of vessels from its pressure vessel laws: some are outside Chapter 28-25 altogether, and others stay subject to construction rules but are excused from the certificate, fee and insurer report sections. The first group includes small diameter and low pressure vessels, cushion tanks and water heaters within set limits, and equipment that another authority controls. The second group covers very small vessels at modest pressure. Owners reading a nameplate should check both lists before assuming a vessel is outside state oversight.

Pressure vessels excluded under R.I. Gen. Laws 28-25-18
VesselLimit in the statuteEffect
Small diameter vesselsInside diameter, width, height or cross section not over 6 inches, any length or pressureOutside the chapter
Low pressure vesselsInternal or external working pressure not over 15 psig, any sizeOutside the chapter
Water vessels with an air cushion120 gallons or less, up to 300 psi and 180 FOutside the chapter
Indirectly heated water vesselsWithin 200,000 Btu/h, 210 F and 120 gallonsOutside the chapter
Vessels outside Section VIII scopeStructures and components ASME Section VIII does not coverOutside the chapter
Federal, transport and research vesselsFederal control, DOT cylinders, vehicles, railroad air tanks, research units with non-code detailsOutside the chapter
Very small vesselsUp to 5 cubic feet at 25 psig, or 1.5 cubic feet at 600 psigExcused from certificate, fee and insurer report sections
Tire inflation air tanksAt gas or service stationsExcused from certificate, fee and insurer report sections

An ordinary plant air receiver larger than those limits is a regulated vessel in Rhode Island, and so is a nitrogen buffer, a clean steam separator, a jacketed reactor or a filter housing above 15 psig and 6 inches. Paul Industries reads the design data against the statute during the quote, so the owner knows from the start whether the vessel needs a permit and certificate.

Who regulates pressure vessels in Rhode Island, and how is pressure vessel jurisdiction split?

The Department of Labor and Training regulates pressure vessels in Rhode Island through the Boiler Unit of its Division of Occupational Safety, under a chief inspector appointed by the Director, and the Code Commission for Occupational Safety and Health adopts the codes the division enforces. Pressure vessel jurisdiction sits with the state alone: section 28-25-21 voids any city or town ordinance on inspecting or installing vessels, sends applications made to a municipality on to the division, and bars a municipal mechanical permit for vessel installation, repair or alteration until the division approves the application where approval applies. Foundations, platforms and structure around a vessel still answer to RISBC-1, which adopts the 2021 International Building Code with state amendments.

Buyers comparing pressure vessel requirements by state will find that Rhode Island’s construction rule matches its neighbors on the ASME code and National Board registration, while its inspection cycle, fee schedule, exemption limits and the state preemption of city ordinances are its own. Paul Industries sets each vessel’s paperwork from the Rhode Island rule itself. For comparison, see pressure vessel fabrication in Massachusetts and pressure vessel fabrication in Connecticut.

Rhode Island pressure vessel inspection: the three-year cycle and who performs it

Rhode Island pressure vessel inspection runs on a three-year cycle for unfired vessels, with an internal inspection where the construction permits and an external inspection for vessels that are not subject to internal corrosion. The state’s certificate fee is $45 per vessel for each three-year period, and the rule counts a group of rolls on a paper machine or dryer operating as one machine as a single vessel. Before an internal inspection, the owner prepares the vessel as far as the inspector deems necessary, which for most process vessels means draining, cleaning, isolating, blinding and opening the manways.

Who inspects pressure vessels depends on the owner. An inspector employed by the state or by the insurer that covers the vessel inspects most of them. A company with a regularly established inspection department can ask for owner-user inspector commissions under 28-25-4, and vessels supervised by an owner-user inspection agency keep the same interval unless the chief inspector agrees otherwise. The chief inspector may also vary the interval for any vessel once the owner documents safe service conditions and the chief inspector has made an external inspection. Inspectors file their reports within five business days.

Inspection options for a Rhode Island unfired vessel
SituationInspection the rule requiresDesign choice that helps
Vessel in corrosive or fouling serviceInternal every three years where construction permitsManways sized for entry, removable internals, drains at low points
Vessel with no internal corrosionExternal every three yearsCorrosion allowance and service record that support the external route
Vessel under an owner-user programSame three-year interval unless the chief inspector agrees otherwiseThickness monitoring locations marked on the drawings
Documented safe serviceChief inspector may vary the interval after an external inspectionComplete data report, materials and operating history kept on file
Jacketed or insulated vesselCovering removed where seams or areas must be seenRemovable insulation panels at seams and nozzles

How often does a pressure vessel need to be inspected while it is being built in Rhode Island?

A pressure vessel built inside Rhode Island needs shop inspection throughout fabrication, because section 28-25-19 requires every manufacturer of unfired vessels in the state to retain an authorized inspection agency for shop inspections. A manufacturer that cannot obtain that service may ask the division’s own inspectors, holding National Board commissions, to perform it at state rates of not less than $190 for a quarter day, $275 for a half day or $500 for a full day. The same section requires every ASME stamped vessel with a signed data report to be registered with the National Board.

For vessels built outside the state, the ASME code sets the inspection points: material review, fit-up, welding, examination and the pressure test are witnessed or reviewed by the authorized inspector before the code symbol goes on. Paul Industries plans hold points into the build schedule so the inspector’s review never becomes the critical path, and prefabricates off site whatever the plant’s layout allows.

Where pressure vessels work in Rhode Island plants

Pressure vessels in Rhode Island serve an industrial base that is small in area and heavy in regulated manufacturing. At the Quonset Business Park in North Kingstown, Electric Boat builds submarine hull modules that are barged to Groton, Connecticut, and its 2026 lease amendment added about 43 acres on Davisville Road for two buildings of more than 540,000 square feet. Hull work itself is under federal control and outside the state statute, but the compressed air, process gas, steam and hydraulic plant in the buildings around it runs on regulated receivers and vessels. Toray Plastics (America) runs a film manufacturing site in North Kingstown, where film lines depend on steam, hot oil and compressed air.

In West Greenwich, Amgen’s Rhode Island site operates a mature biologics plant making ten products, with a second plant in start-up. Biologics plants need clean steam generators and separators, water for injection and purified water storage under pressure, jacketed buffer and media vessels, and autoclave and sterilizer shells, built in stainless with ASME BPE finishes. Paul Industries supplies those vessels and connects them to ultrapure water systems in Rhode Island; more on that market is on biotech. Finishing and jewelry plants in Providence, Cranston, Pawtucket and East Providence use pressure filter housings, air receivers and heated process vessels, and hospitals and campuses run deaerators, flash tanks and heat exchanger shells that sit beside the work on boiler repair in Rhode Island.

Vessels Rhode Island plants order, with typical construction
VesselWhere it serves in Rhode IslandTypical constructionInspection notes
Compressed air receiverFabrication halls at Quonset, finishing shops, packaging linesCarbon steel, Section VIII Division 1, automatic drain, relief valve at the compressor’s ratingRegulated above 15 psig and the small vessel limits; internal access through an inspection opening
Clean steam separator and condensate potBiologics and sterile filling plants in Kent County316L stainless, polished, fully drainable, sanitary connectionsClean internals often support an external route; data report kept for qualification files
Jacketed process vesselFood, chemical and finishing plants in Providence and the Blackstone ValleyStainless or lined steel shell with a dimple or conventional jacket, each side ratedShell and jacket are both pressure parts; insulation panels removable at seams
Deaerator and blowdown tankHospital, campus and plant boiler roomsCarbon steel with a corrosion allowance, vent condenser and level controlsInternal inspection every three years where construction permits
Pressure filter housingRinse water recovery, process filtration and water treatmentStainless or lined steel, quick-opening or bolted closureQuick-opening closures need the code’s interlock and indicator details
Heat exchanger shellSteam to hot water converters and process exchangersCarbon or stainless shell to Section VIII, tubes to suit the fluidsShell side and tube side each carry a rating on the nameplate

Most Rhode Island orders mix one or two clean stainless vessels with several carbon steel utility vessels, and Paul Industries builds them under one schedule so the setting, piping and first inspections run together.

Designing a pressure vessel for Rhode Island service

A pressure vessel for Rhode Island service is designed from the process data sheet, the site’s weather and the inspection route the owner expects to use. Stainless 316L with polished, drainable internals suits biologics and food plants, where vessels are passivated before service as described on passivation services in Rhode Island. Carbon steel with a corrosion allowance suits air receivers, condensate and utility vessels. Each pressure vessel, Rhode Island registration included, is specified with the inspection access the owner wants over its service life. Outdoor vessels on the coast at Quonset, Newport and Providence face salt air, so coatings, stainless or coated fasteners, sealed insulation jackets and drain points at saddles and skirts protect the shell.

Winter sets the minimum design metal temperature for outdoor vessels and for vessels that see expanding gas or refrigerant, and the impact testing that follows from it. Wind and snow loads for tall outdoor vessels follow the Rhode Island Building Code, which replaces the national maps with a city and town table. Relief protection is part of the design: pressure vessel relief valve requirements in the ASME code set the set pressure, capacity, inlet and outlet sizing and discharge routing, and the statute places safety valve repair under the National Board VR program. Paul Industries sizes the relief devices with the vessel and routes the discharge to a safe point.

State Special, second-hand and non-ASME pressure vessels in Rhode Island

Non-ASME pressure vessels have a narrow path in Rhode Island: installing, operating, selling or offering a nonstandard vessel is prohibited without the chief inspector’s permission. A standard vessel bears the ASME stamp, the API-ASME stamp, the ASME and National Board stamps together, or the stamp of a jurisdiction with an equivalent construction standard. When a valid impediment prevents full ASME compliance, the owner may seek approval as a State Special by submitting construction details, material specifications and calculations, in English and US customary units and approved by a registered professional engineer experienced in vessel design, before construction starts.

A second-hand vessel, one that has changed both location and ownership, may be set only after the owner files an installation application and the chief inspector approves it. A vessel that leaves Rhode Island for temporary use or repair needs a new installation application to come back, and a nonstandard vessel that leaves the state may not be reinstalled at all. Imported skids built to European or other codes are the usual source of nonstandard vessels, and Paul Industries reviews skid vessels early so a code-stamped replacement can be specified before delivery.

ASME pressure vessel repair requirements for vessels already in Rhode Island service

ASME pressure vessel repair requirements in Rhode Island come from the 2025 National Board Inspection Code, with notice to the Boiler Unit or an authorized inspector before any welded repair or alteration and the NBIC form filed with the division afterward. Rule 2.5.21 places alterations under an ASME certificate of authorization, and the rule’s alteration definition covers a rerate to a higher pressure or temperature and a lower minimum temperature that requires added mechanical tests. Replaced fittings, such as relief valves, gauges and drains, meet the requirements for new installations.

Stamping must stay visible: insulation and coatings may not hide it unless a record shows where it is. When a nameplate or stamping becomes unreadable, the inspector tells the owner to have it restamped, and the request goes to the chief inspector with proof of the original stamping; the restamping is witnessed by an authorized inspector and duplicates the original except for the ASME code symbol. Paul Industries adds nozzles, replaces heads and shell courses, repairs pitting and cracked welds and rerates vessels with the calculations, examinations and tests each change needs, alongside industrial welding services in Rhode Island and hydrostatic testing.

Shipping pressure vessel loads into Rhode Island by road and sea

Shipping pressure vessel loads into Rhode Island works by highway for most shop-built vessels and by sea for oversize units, because the state has two deep-water ports with heavy lift capacity. The Port of Providence, RI, operated as ProvPort, handles bulk, breakbulk and project cargo on roughly 135 to 140 acres with on-dock rail. The Port of Davisville at Quonset handles project cargo and breakbulk with a 150 metric ton mobile harbor crane, beside the business park where many large vessels are set.

Highway loads into Providence, the Blackstone Valley and South County are planned around route surveys for height, width and bridge limits, and the vessel’s lifting lugs, saddles and shipping supports are designed with the load. Paul Industries plans the delivery, the crane and the setting as part of the fabrication schedule, and fuel or water storage that is not pressure-rated is covered on tank fabrication in Rhode Island.

How much does a pressure vessel cost for a Rhode Island plant?

A pressure vessel for a Rhode Island plant costs what its size, design pressure and temperature, material, internal finish, nozzle count, jacket and examination requirements demand, and stainless clean utility vessels with polished internals cost several times a carbon steel air receiver of the same volume. The state’s charges are small and fixed: $45 per vessel for each three-year certificate, and state shop or special inspections from $190 for a quarter day to $500 for a full day when the division’s inspectors are used. Delivery by heavy haul or sea, crane work and setting add to large vessels.

Paul Industries gives a budget range from the data sheet and comparable vessels, then a firm price once the design is settled. Send the process data, design pressure and temperature, volume, material, nozzle list, finish requirements and site photos for the closest first number.

Who fabricates pressure vessels in Rhode Island?

Paul Industries fabricates pressure vessels in Rhode Island for biologics plants, defense suppliers, film and materials plants, metal finishers, food plants, hospitals and campuses, from Providence and Cranston to the Blackstone Valley, West Greenwich, Quonset, Newport and Westerly. Headquartered at 256 Shore Drive in Kilmarnock, Virginia, and formerly based in northern New Jersey and then Pennsylvania, Paul Industries is an East Coast contractor that builds vessels for every part of Rhode Island, for plants across New England and for sites in all 50 states. The program in its headquarters state is on pressure vessel fabrication in Virginia, and the national scope is on pressure vessel fabrication.

Paul Industries designs, fabricates, supplies, sets, pipes, tests and starts up vessels, and repairs and rerates vessels already in service, through supply-only, design-build or complete installation routes.

Pressure vessels from Paul Industries for Rhode Island sites

Paul Industries carries a Rhode Island vessel from the data sheet to the posted certificate: design to the 2025 ASME code, fabrication and examination, National Board data, the permit to install, setting and piping, relief protection, the first inspection and startup. More on the state’s plants is on the Rhode Island page. Send the process conditions, the nozzle list and the site details, then request a quote or call 201-450-8280.

Standards referenced: R.I. Gen. Laws Chapter 28-25, Boiler Inspection and Pressure Vessels · 260-RICR-30-10-2, Boiler and Pressure Vessel Inspection (amendment effective December 24, 2025) · ASME Boiler and Pressure Vessel Code, 2025 edition, Section VIII Divisions 1 and 2, Sections II, V and IX · National Board Inspection Code (NBIC), 2025 edition · ASME BPE, Bioprocessing Equipment · RISBC-1 Rhode Island Building Code (2021 International Building Code with Rhode Island amendments)

Frequently asked questions

Who builds air receivers and process vessels for plants in Providence, Cranston and East Providence?

Paul Industries builds ASME air receivers, filter housings, heated process vessels and condensate receivers for manufacturers, metal finishers, hospitals and campuses in Providence, Cranston and East Providence. Finishing plants in those cities often need vessels in stainless or lined steel for chemistry and rinse water, and receivers sized for compressed air demand. Paul Industries delivers each vessel with its National Board data and sets it under the Rhode Island permit to install.

Does Paul Industries supply vessels to the Quonset Business Park in North Kingstown?

Paul Industries supplies receivers, separators, heat exchanger shells and process vessels to plants at the Quonset Business Park in North Kingstown, and large vessels can arrive by sea through the Port of Davisville beside the park. Shipyard supply, film and food plants at Quonset run heavy compressed air, steam and process gas loads. Paul Industries designs outdoor vessels there for salt air and coastal wind.

Who fabricates clean steam and water vessels for biologics plants in West Greenwich and Kent County?

Paul Industries fabricates clean steam separators, purified water and water for injection storage vessels, jacketed buffer and media vessels and sterilizer shells for biologics plants in West Greenwich and the Kent County corridor. Those vessels are built in 316L stainless with ASME BPE finishes, passivated and documented for qualification. Paul Industries carries them through setting, connection and startup.

Can Paul Industries build vessels for plants in Woonsocket, Lincoln and the Blackstone Valley?

Paul Industries builds and installs pressure vessels for manufacturers, food plants and finishing shops in Woonsocket, Lincoln, Smithfield, Pawtucket and the rest of the Blackstone Valley. Many of those plants occupy older mill buildings with tight access, so vessels are sized, split or fitted with removable supports to pass through existing openings. Paul Industries surveys the route before fabrication.

How often does a pressure vessel need to be inspected in Rhode Island?

A pressure vessel in Rhode Island needs a certificate inspection every three years under rule 2.5.2, internal where its construction permits and external for vessels not subject to internal corrosion. Vessels under an owner-user inspection agency keep the same interval unless the chief inspector agrees otherwise, and the chief inspector may vary any interval on documented safe service. Paul Industries designs vessels with the access the internal inspection needs.

Does a 120-gallon air receiver need a Rhode Island certificate?

A 120-gallon air receiver needs a Rhode Island certificate when it operates above 15 psig, because the statute’s 120-gallon exemption applies to vessels holding water under pressure with air serving only as a cushion, and a 120-gallon receiver is far larger than the 5 cubic foot limit for small vessels. Most plant air receivers are therefore regulated. Paul Industries supplies receivers with National Board data and relief valves sized to the compressor.

Who inspects pressure vessels at a Rhode Island plant?

An authorized inspector employed by the state or by the vessel’s insurer inspects most pressure vessels at a Rhode Island plant, and an owner-user inspector inspects vessels at companies the state allows to run their own inspection department. Each holds a Rhode Island commission, renewed every year by March 31. Paul Industries prepares vessels for the inspector and repairs whatever the report lists.

Can a city or town in Rhode Island require its own vessel permit?

A city or town in Rhode Island cannot pass its own ordinance on inspecting or installing pressure vessels, because section 28-25-21 voids such rules and sends applications to the state division. A municipality also holds its mechanical permit for vessel work until the division approves the application where approval applies. Building permits for the structure around the vessel still go through the city or town. Paul Industries files both in sequence.

Can a skid with a European-code vessel be installed in Rhode Island?

A skid with a European-code vessel can be installed in Rhode Island only with the chief inspector’s permission, because the rule treats a vessel without the ASME, API-ASME or equivalent jurisdiction stamp as nonstandard. The State Special route requires engineer-approved details and calculations before construction. Paul Industries reviews imported skids during procurement and specifies ASME stamped vessels where that keeps the schedule.

What does National Board registration add to a vessel for a Rhode Island plant?

National Board registration adds a permanent record of the vessel’s construction, filed under its National Board number and available to any jurisdiction. Rhode Island requires the data report to reach the chief inspector through the National Board, so registration is how the state receives it. Repairs and alterations later reference that record. Paul Industries includes the registered data report in every turnover package.

How are pressure vessel relief valve requirements met on a new Rhode Island vessel?

Pressure vessel relief valve requirements on a new Rhode Island vessel are met by sizing a code-marked relief device for the worst credible overpressure case, setting it at or below the maximum allowable working pressure, and piping the discharge to a safe location. Replaced relief devices must meet the rules for new installations. Paul Industries supplies the device, the sizing basis and the discharge piping with the vessel.

Can Paul Industries add a nozzle to a vessel already in Rhode Island service?

Paul Industries adds nozzles to vessels already in Rhode Island service under the 2025 National Board Inspection Code, with notice to the Boiler Unit or an authorized inspector before welding and the NBIC form filed afterward. A nozzle that changes the vessel’s design values becomes an alteration under an ASME certificate of authorization. Paul Industries prepares the calculations, reinforcement design, examination and pressure test.

What happens to a Rhode Island vessel whose stamping cannot be read?

A Rhode Island vessel whose stamping cannot be read is restamped with the chief inspector’s permission, after the owner sends proof of the original stamping. An authorized inspector witnesses the work, the new stamping matches the original except for the ASME code symbol, and the inspector files notice with a facsimile. Paul Industries removes insulation and coatings at the stamping and prepares the request.

Do steam-heated dryer rolls in Rhode Island each need a certificate?

Steam-heated dryer rolls in Rhode Island are inspected, but the rule counts a group of rolls on a paper machine or dryer operating as one machine as a single pressure vessel for the $45 triennial fee. Each roll is still a pressure vessel under the code. Paul Industries repairs roll heads, journals and steam joints and documents the work for the group’s inspection.

Is a vessel at 15 psig covered by the Rhode Island law?

A vessel whose internal or external working pressure stays at 15 psig or less is exempt from the Rhode Island law regardless of size, which covers many vented process tanks, low pressure receivers and atmospheric equipment. Above 15 psig the vessel is regulated unless another exemption applies. Paul Industries confirms the design pressure and relief setting so the vessel’s status is clear before fabrication.

How long does a new ASME vessel take for a Rhode Island project?

A new ASME vessel for a Rhode Island project takes the time needed for design approval, material procurement, fabrication, examination, inspection and the pressure test, and plate, forgings and stainless fittings often set the critical path. Clean utility vessels add polishing, passivation and documentation. Paul Industries orders long-lead material at release and gives a schedule with the quote.

What records should a Rhode Island owner keep for each pressure vessel?

A Rhode Island owner should keep each vessel’s data report and National Board number, the state serial number, the current certificate, every inspection report, repair and alteration forms, relief device records and thickness readings. Those records support a request to vary the inspection interval and speed any repair. Paul Industries hands over a complete file at turnover and adds to it after each repair.

Specifying a code vessel for a Rhode Island plant?

Send the process data, design pressure and temperature, volume, material and nozzle list. Call 201-450-8280 or request a quote.