Paul Industries designs, pipes, installs and services data center liquid cooling in Missouri: coolant distribution units, direct-to-chip cold plate loops, rear door heat exchangers, the facility water plant that feeds them and the freeze-safe dry cooler yards that reject their heat, for halls in Kansas City, Independence, St. Louis and St. Charles County. Missouri’s mix of 90 degree summers and long freezing winters, plus the gigawatt-scale campuses now under construction, make liquid cooling here as much a yard and glycol question as a rack question. Paul Industries, headquartered at 256 Shore Drive in Kilmarnock, Virginia, builds liquid cooling loops across Missouri and in all 50 states.
Request a quote or call 201-450-8280
Where data center liquid cooling in Missouri starts: rack, loop and yard
Data center liquid cooling in Missouri starts at three places at once: the rack, where cold plates or rear door coils pick up heat; the technology cooling loop, where a coolant distribution unit separates the rack fluid from the building’s facility water; and the yard, where dry coolers, towers or chillers send that heat outdoors in a climate that swings from humid 90 degree afternoons to nights near zero. Most projects in the state get the rack decisions from the IT vendor and the hardest decisions at the other two places: what temperature the facility water runs, what fluid it carries, how it survives a Kansas City January, and how it ties into an air-cooled plant that already exists.
The national overview of cold plates, immersion, rear door heat exchangers and CDUs is on the data center liquid cooling page. This page covers what changes in Missouri: the weather that sets the facility water temperature, the closed-loop water numbers a Missouri city has published, freeze protection, fill water, retrofits in operating halls and cost on Missouri power.
Why liquid cooling? Data center racks in Missouri have outgrown air
Why liquid cooling data center operators in Missouri are adding it comes down to rack density: accelerator servers now put tens of kilowatts, and in the newest designs more than 100 kilowatts, into one rack, and air cannot carry that much heat through a rack without enormous airflow, noise and fan power. Water carries roughly 3,500 times as much heat per unit volume as air, so a loop of modest pipe replaces a wall of fans. The campuses under construction in the Kansas City area and along Interstate 70 are built for exactly this class of hardware.
So are data centers liquid cooled in Missouri today? Many halls still run fully on air, especially enterprise rooms in Springfield, Columbia and Jefferson City and older colocation space in St. Louis. The new hyperscale and dense compute halls are being designed for liquid from the start, and operating halls in both metros are adding liquid-cooled rows inside rooms that stay air-cooled for storage and network gear. The result for most Missouri owners is a hybrid: liquid to the hottest chips, air for everything else, and one plant serving both.
How does data center liquid cooling work, from cold plate to dry cooler?
Data center liquid cooling works by pumping a coolant through a cold plate fixed to each processor, carrying the heat to a coolant distribution unit, transferring it there to facility water, and rejecting it outdoors through dry coolers, towers or chillers. In data center liquid cooling direct to chip designs, the cold plate sits on the CPU or GPU package with a thermal interface, and microchannels inside it pull heat from the chip at high flux. Rack manifolds distribute coolant to each server through dripless quick disconnects. The data center liquid cooling CDU holds the pumps, the heat exchanger, filtration, expansion and controls, and keeps the technology loop at a set temperature and pressure.
A data center liquid cooling cold plate typically captures most of the server’s heat, but memory, power supplies, drives and network cards still shed heat to air, so a liquid-cooled hall keeps air handling at a reduced size. A data center liquid cooling loop is therefore two loops in practice: a small, very clean technology loop between CDU and racks, and a larger facility water loop between CDUs and the heat rejection plant. Keeping them separate protects the cold plates from whatever the facility loop carries.
Is data center water cooling closed loop? What the Independence campus shows
Data center water cooling for liquid-cooled halls is usually closed loop at the rack and the CDU, and it can be closed loop all the way to the yard when dry coolers reject the heat; it becomes open only where a cooling tower evaporates water. The Nebius campus in Independence, where ground was broken in May 2026, gives Missouri a published example. The City of Independence describes a closed-loop cooling system: filling it takes roughly a million gallons per 200 megawatt building, around a fifth of that volume is topped up yearly, and ongoing use at full buildout is put at 400,000 to 640,000 gallons annually. The city also states that the cooling water does not go into the stormwater system.
Those figures show the scale of a closed loop’s water: large at the first fill, small afterward. They also show what the design has to get right. A loop that holds a million gallons needs a fill plan, a treatment program sized for that volume, makeup and expansion capacity for the replenishment, and drain-down and recovery procedures so maintenance does not throw treated coolant away. The same campus needs at least 800 megawatts, which the city says will come from a new generating facility at the retired Blue Valley Power Plant site, with Southwest Power Pool rules adding reserve capacity on top.
Data center liquid cooling temperature and Missouri weather
Data center liquid cooling temperature is set by the facility water supply class, and ASHRAE’s thermal guidelines name the classes by their upper supply limit in Celsius: W17, W27, W32, W40, W45 and W+. A Missouri plant’s heat rejection choice follows from the class. Kansas City’s July normal high is 88 degrees Fahrenheit and St. Louis’s is 90, with 36 and 47 days a year at 90 or above, so a dry cooler that needs a few degrees of approach above the outdoor dry bulb can make W32 or warmer water most of the year without a compressor, while W17 water needs chillers for much of the summer.
| Class | Supply limit | Missouri heat rejection | Compressor hours |
|---|---|---|---|
| W17 | 17 C (62.6 F) | Chillers with tower or air-cooled condensers; economizer in winter | Most of the warm season |
| W27 | 27 C (80.6 F) | Towers with chiller trim, or dry coolers with chiller trim | Hot and humid summer days |
| W32 | 32 C (89.6 F) | Dry coolers or towers, with chiller or adiabatic trim for the hottest days | A small share of the year, mostly July and August afternoons |
| W40 and W45 | 40 to 45 C (104 to 113 F) | Dry coolers year round; heat warm enough to reuse | Little or none |
The class is a supply limit for the facility water. The CDU adds an approach, so the coolant reaching the cold plate runs a few degrees warmer than the facility water, and the chip vendor’s limits on coolant inlet temperature and flow set how warm the facility side can go. Paul Industries works from the server vendor’s data, the CDU’s approach and the site’s weather file to choose the class, then sizes the yard so the class holds on the hottest Missouri afternoon.
Data center liquid cooling glycol and Kansas City winters
Data center liquid cooling glycol belongs in any Missouri loop that passes through outdoor equipment, because Kansas City sees a low at or below 32 degrees on about 107 days in an average year, with January lows averaging 20, and a dry cooler coil full of plain water bursts in a hard freeze. Propylene glycol at a concentration matched to the site’s extreme low protects the coil, while the technology loop indoors usually stays on treated water or a low-concentration glycol specified by the cold plate maker.
Glycol changes the hydraulics. It carries less heat per gallon than water and grows more viscous as it cools, so pumps, heat exchangers and pipe sizes are selected for the mix, not for water. Missouri plants also need a winter plan for power loss: if pumps stop on a zero degree night, the yard coils drain to a tank or hold enough glycol to ride it out. Paul Industries designs the glycol concentration, the fill and makeup system, the expansion tanks and the freeze alarms together, and tests concentration each autumn as part of service.
Choosing data center liquid cooling vs air cooling for a Missouri hall
Data center liquid cooling vs air cooling in Missouri is a choice about density, power and water: liquid removes heat at the chip with small pumps instead of large fans, runs warmer water that gives more free cooling in a Missouri winter, and fits dense racks that air cannot cool, while air remains the simpler answer for low-density rooms. The table compares them for a Missouri site, with immersion included because some owners consider it.
| Factor | Air cooling | Direct-to-chip liquid | Immersion |
|---|---|---|---|
| Practical rack density | Low to moderate | High, with air for remaining heat | High |
| Facility water temperature | Cool, to make cold supply air | Warm; W27 to W45 classes | Warm |
| Missouri free cooling | Winter and shoulder months | Most of the year with dry coolers at W32 and above | Most of the year |
| Fan power in the hall | High | Reduced | Very low |
| Changes to the building | Air handling, containment | CDUs, facility water to rows, manifolds | Tanks, floor loading, fluid handling |
| Fits existing St. Louis or Kansas City halls | Already in place | Row by row retrofit | Dedicated rooms |
On liquid cooling vs immersion cooling, direct-to-chip is the route most new Missouri campuses describe, because it keeps standard rack form factors and service practices; immersion suits dedicated rooms where the owner accepts tanks, dielectric fluids and different maintenance routines. Paul Industries builds the facility side for either, and the immersion route is described on the data center immersion cooling page.
What goes into a Missouri data center liquid cooling loop
Data center liquid cooling systems in Missouri are built from the same components as anywhere else, but the yard and the fill water carry Missouri-specific choices. The data center liquid cooling equipment list runs from the CDUs and rack manifolds through the facility water piping, isolation valves, strainers and filters, flow meters, expansion tanks, glycol makeup, heat exchangers, and the dry coolers, towers or chillers at the end of the line. Data center liquid cooling piping inside the hall is usually stainless steel or copper on the technology side and steel, stainless or approved plastics on the facility side, chosen for compatibility with the coolant and the cold plate metals.
| Component | Work | Test and record |
|---|---|---|
| Facility water mains and branches to rows | Fabrication, installation, supports, isolation valves at every branch | Hydrostatic or pneumatic test to the adopted mechanical code, flush, cleanliness record |
| CDUs | Setting, piping, power and controls connections | Startup, flow and pressure verification, alarm tests |
| Rack manifolds and hoses | Connection to CDU secondary loop | Leak check, particle filtration during first circulation |
| Dry coolers or towers | Setting, glycol or treated water fill, freeze protection | Capacity check at available weather, freeze alarm test |
| Glycol and makeup | Fill station, mixing, expansion tanks | Concentration record, pH and inhibitor levels |
Missouri has no statewide mechanical code for private buildings, so the pressure test and inspection requirements come from the code the city or county has adopted. Paul Industries confirms the edition with the building department, tests every new section before insulation and before it connects to a live loop, and keeps the records in the turnover package.
Data center liquid cooling coolant and Missouri fill water
Data center liquid cooling coolant in the technology loop is usually treated, low-conductivity water or a propylene glycol blend with corrosion inhibitors, specified by the cold plate and CDU makers, because the microchannels in a cold plate clog with particles and the mixed metals corrode with the wrong chemistry. City water in Missouri is a poor fill for that loop as delivered. The City of St. Louis Water Division’s 2025 report, for example, lists chloramine disinfection, average dissolved solids of 298 parts per million and average hardness of 129 parts per million as calcium carbonate, all of which a cold plate loop must be protected from.
Paul Industries fills technology loops with purified water or premixed coolant, circulates through fine filtration until particle counts meet the vendor’s limit, doses inhibitors and records conductivity, pH and concentration before racks connect. The facility loop gets its own treatment program matched to its metals and to the makeup water. Where a site needs purified water on demand for coolant makeup, the system can be built alongside the ultrapure water systems in Missouri that Paul Industries also installs.
Adding liquid cooling to air-cooled halls in St. Louis and Kansas City
Retrofitting an operating air-cooled hall for liquid means bringing facility water to rows inside a live room, usually above the racks or under a raised floor, without dripping on running equipment or interrupting the air plant that still cools the rest of the hall. Most of the liquid cooling St. Louis colocation owners add today goes into rooms like this, and the work starts with the source of facility water: a branch from the existing chilled water plant with a heat exchanger, a dedicated dry cooler loop for warm water, or both. Then pipe routes, isolation valves at every branch, drip trays and leak detection go in before the first CDU is set.
Paul Industries stages retrofit work row by row: prefabricated pipe spools reduce hot work in the room, hot taps or pre-installed valves avoid shutting down the plant, and each new section is tested and flushed before it opens to the live system. For data center liquid cooling Kansas City operators need on a short schedule, the bigger constraint is usually the yard: whether there is space and electrical capacity for added dry coolers, and whether sound limits allow them.
Keeping a Missouri loop healthy: data center liquid cooling maintenance
Data center liquid cooling maintenance centers on fluid quality, filtration and leak detection, because a cold plate loop fails slowly through fouling and corrosion long before it fails suddenly through a leak. A Missouri service program adds seasonal tasks: glycol concentration checks before the first freeze, dry cooler coil cleaning after cottonwood and pollen season, and verification that freeze alarms and drain-down valves work. Paul Industries sets the sampling schedule for conductivity, pH, inhibitor level, glycol concentration and particle counts, changes CDU filters, tests leak detection and exercises isolation valves so they close when needed.
What does data center liquid cooling cost in Missouri?
Data center liquid cooling cost in Missouri depends on how many racks and CDUs are involved, whether facility water already reaches the rows, the class of water the plant must make, the yard equipment and freeze protection, and how much of the work happens inside a live room. A new hall designed for liquid from the start carries the facility piping in its base build; a retrofit pays for routing pipe through an occupied space, staged tie-ins and temporary measures. The energy side favors liquid: fan power in the hall drops, and warm water extends free cooling. Priced at 8.25 cents per kilowatt-hour, the EIA’s 2025 Missouri industrial average, a megawatt of hall fan power taken off the meter is worth about $722,700 a year.
How much cooling does a data center need? Close to one watt of cooling for every watt of IT load, because nearly all of the electrical input becomes heat; with liquid cooling, most of that heat leaves through the facility water and the rest through air. Paul Industries prices liquid cooling supply-only for CDUs and yard equipment, design-build to a performance target, or as complete installation to the owner’s engineered design, with equipment, piping, testing and startup shown separately.
Phasing changes the cost picture on the big Missouri campuses. A site that will grow over three to five years, as the Independence campus describes, saves money by installing facility water mains, headers and valved connections sized for the final load in the first phase, so later buildings tie in without shutting down the loops already running. The opposite choice, sizing each phase only for itself, costs less on day one and more at every expansion, when crews have to cut into live piping. Paul Industries prices both approaches so the owner sees the trade before the first phase is designed, and shows how much of the later cost moves forward.
Yard equipment is the other swing item. A W32 plant built on dry coolers needs more coil area and fan power than a tower plant of the same capacity, but it uses almost no water after the fill, which matters where a city or a permit condition limits water. Adding adiabatic pads or a small chiller for the hottest afternoons keeps the coil count down. Paul Industries runs the comparison against Missouri weather and the owner’s tariff before recommending a yard.
Who does liquid cooling for data centers in Missouri?
Paul Industries does liquid cooling for data centers in Missouri: it designs the facility water side, supplies and sets CDUs and yard equipment, fabricates and installs the piping, fills and treats the loops, tests, starts up and maintains them, in Kansas City, Independence, St. Louis and every other part of the state. Among data center liquid cooling providers, Paul Industries carries the whole path from the rack manifold connection to the dry cooler under one contract, so the water temperature, the fluid, the tests and the freeze protection are answered by one firm.
Related Missouri pages cover the rest of the plant: data center cooling in Missouri for chilled water and heat rejection, data center commissioning in Missouri for testing, data center mechanical contractor in Missouri for the full campus mechanical scope, and chiller repair in Missouri for the machines that trim warm-water plants in summer. For dry and glycol loops in general see closed-loop cooling systems. In the headquarters state, see data center liquid cooling in Virginia; in a neighboring Midwest state, data center liquid cooling in Ohio. The state hub is Missouri.
Liquid cooling loops from Paul Industries across Missouri
Paul Industries designs, supplies, installs, flushes, fills, tests, starts up and services data center liquid cooling across Missouri: CDUs, rack manifold connections, facility water piping, heat exchangers, dry coolers and towers, glycol systems and the controls that tie them to the existing plant. New campuses, row-by-row retrofits and warm-water plant conversions are all in scope. Owners can buy supply-only, design-build or complete installation. Call 201-450-8280 or request a quote.
Standards referenced: ASHRAE TC 9.9 Thermal Guidelines, liquid cooling classes W17 to W+ · ASHRAE 90.4 · ASME B31.9 building services piping · City and county mechanical codes adopted in Missouri · Missouri DNR major water user registration (RSMo 256.410)
Frequently asked questions
Who installs liquid cooling for a data center in Independence, Missouri?
Paul Industries installs liquid cooling for data centers in Independence and across the Kansas City area: CDUs, facility water piping to the rows, dry coolers and glycol systems, with pressure tests, flushing and fill records for each loop. Campuses there are built in phases, so the facility water mains are sized and valved for later buildings. Call 201-450-8280 to discuss a project in Independence or the Northland.
Can an existing St. Louis colocation hall add liquid-cooled racks?
An existing St. Louis colocation hall can add liquid-cooled racks row by row by bringing facility water from the chilled water plant through a heat exchanger or from a new dry cooler loop, then setting CDUs at the rows. Leak detection, drip protection and isolation valves go in first. Paul Industries stages the work so the air-cooled rows keep running throughout.
What facility water temperature should a Missouri liquid-cooled hall run?
Many new halls design for ASHRAE’s W32 class or warmer, because Missouri summers reach the high 80s and low 90s on average in July, and a dry cooler can make 32 degree Celsius water most of the year. The server vendor’s coolant inlet limit and the CDU approach set the ceiling. Paul Industries checks both against the site’s weather data before fixing the class.
Do Missouri liquid cooling loops need glycol?
Any loop with coils or piping outdoors in Missouri needs glycol or a reliable drain-down, because Kansas City averages about 107 freezing nights a year and St. Louis about 85. Indoor technology loops usually run treated water or a coolant blend set by the cold plate maker. Paul Industries specifies concentrations for the site’s extreme low and checks them every autumn.
How much water does a closed-loop liquid cooling system use?
A closed loop uses most of its water once, at the first fill, then only makeup for maintenance and losses. Independence’s published figures for its large campus are about one million gallons per 200 megawatt building for the fill and about 20 percent replenished each year. Paul Industries plans fill sources, treatment, expansion and drain recovery around those volumes.
What is a CDU and why does every liquid-cooled row need one?
A coolant distribution unit separates the clean technology loop serving the cold plates from the facility water loop, using a heat exchanger, pumps, filters, an expansion tank and controls. It keeps the rack coolant at a set temperature and pressure and protects cold plates from facility water contaminants. Paul Industries sets, pipes, starts up and services CDUs in row, rack and room configurations.
What does a cold plate loop need to be clean enough?
Cold plates have fine channels that clog with particles, so the technology loop is flushed and filtered after installation until particle counts meet the vendor’s limit, then filled with specified coolant. Welding, cutting and threading debris has to come out before racks connect. Paul Industries flushes with temporary filtration, records the results and keeps CDU filters on a change schedule after startup.
How do Missouri power prices affect the case for liquid cooling?
Missouri’s 2025 average industrial electricity price was 8.25 cents per kilowatt-hour and the commercial price 10.46 (EIA). Liquid cooling cuts fan power in the hall and raises water temperature, which extends free cooling and reduces chiller hours. At the industrial average, each megawatt of fan power removed saves about $722,700 a year. Paul Industries estimates savings with the owner’s own tariff and load profile.
Can liquid cooling share a plant with existing air-cooled rooms?
Liquid cooling can share a plant with air-cooled rooms through a heat exchanger that lets the liquid loop run warmer than the chilled water, or through a separate warm-water loop that uses the plant’s chillers only on the hottest days. The design keeps the air rooms at their supply temperature while the liquid rows run warm. Paul Industries models both loads before choosing the tie-in.
What leak protection does a liquid-cooled row need?
A liquid-cooled row needs leak detection under and above the manifolds and CDUs, drip trays where pipe runs over equipment, dripless quick disconnects at the servers, isolation valves at each branch, and alarms that reach the operators. Pressure and flow monitoring at the CDU spots slow leaks. Paul Industries installs and tests each of these before racks connect.
What records come with a new liquid cooling installation?
The turnover package includes pressure test records, flush and cleanliness records, fill and coolant analysis, CDU startup sheets, valve and instrument lists, as-built drawings and the control sequence. Commissioning results are added when the owner’s testing is complete. Paul Industries assembles the package for each loop and keeps it current through service visits.
Does liquid cooling change what a Missouri data center needs from its chillers?
Liquid cooling usually reduces chiller hours, because warm facility water can be made by dry coolers or towers for most of the year, leaving chillers to trim the hottest summer afternoons and to serve the remaining air load. Some owners keep chillers sized for full load as backup. Paul Industries sizes the trim and backup capacity with the owner’s redundancy rules.
Can server heat from a Missouri data hall be reused?
Heat from warm-water liquid cooling, especially in the W40 and W45 classes, is warm enough for building heat, snow melting or process preheating, and Missouri’s long heating season gives it months of use. The challenge is finding a steady heat user near the hall. Paul Industries designs the heat exchangers, piping and controls when the owner has a user in mind.
Which drawings and data does Paul Industries need to price a liquid cooling retrofit?
Send the rack count and densities by phase, the server vendor’s coolant specifications, the existing plant and room drawings, the target facility water class, yard space, and any sound or water conditions. Paul Industries replies with a budget figure based on comparable loops and fixes the price when the design is settled. Call 201-450-8280 or request a quote.
How long do dry coolers serving liquid loops last in Missouri weather?
Dry coolers last longest when coils stay clean, fans and motors are maintained and glycol chemistry protects the tubes. Missouri’s cottonwood and pollen seasons foul coils in late spring, and summer storms bring debris. Paul Industries cleans coils, checks fan bearings and motors, and tests glycol on a set schedule to keep capacity where the design needs it in July.
What is the difference between the technology loop and the facility loop?
The technology loop is the small, very clean circuit between the CDU and the cold plates in the racks. The facility loop is the larger circuit between the CDUs and the heat rejection plant. A heat exchanger in each CDU separates them, so facility water quality, glycol and debris never reach the chips. Paul Industries builds and treats each loop to its own standard.
Bringing liquid-cooled racks into a Missouri hall?
Send rack counts and densities, the server vendor’s coolant specifications, the existing plant drawings and the yard layout. Call 201-450-8280 or request a quote.
