Paul Industries designs, installs, tests and maintains data center liquid cooling in West Virginia, including direct-to-chip cold plate loops, coolant distribution units, rear-door heat exchangers and the warm water plants that feed them, from its headquarters at 256 Shore Drive, Kilmarnock, Virginia. West Virginia suits warm water liquid cooling unusually well, because a mountain climate lets dry coolers carry the heat for most of the year and the gigawatt campuses proposed under the 2025 microgrid law are planning for dense racks from the first building. Paul Industries builds every loop from the facility plant to the rack manifold.
Request a quote or call 201-450-8280
What does data center liquid cooling in West Virginia involve?
Data center liquid cooling in West Virginia involves three connected loops: a facility water system that rejects heat outdoors, coolant distribution units that separate that water from the servers, and a technology cooling system that carries coolant through manifolds and hoses to cold plates on the processors. Rear-door heat exchangers, which cool the air leaving a rack with water coils, sit between air and liquid and suit rooms whose servers still rely on air.
What changes in West Virginia is the outdoor end. In a hot or humid market the facility water usually comes from chillers for much of the year. In West Virginia’s cool climate, warm facility water comes from dry coolers for most hours, with chillers or adiabatic assist only on summer afternoons, so the liquid cooling decision and the plant decision are the same decision. The data center cooling in West Virginia page sets out the climate and the plant choices; this page follows the heat from the chip outward.
Paul Industries is an East Coast contractor, headquartered in Kilmarnock, Virginia, and formerly based in northern New Jersey, then Pennsylvania. Its West Virginia liquid cooling work draws on the same practice that serves owners in all 50 states and at plants outside the United States. The West Virginia overview covers the state’s plant work more broadly, and the national data center liquid cooling guide explains the components in general terms.
Where does dense computing sit in West Virginia?
Dense computing in West Virginia sits in three places today: university research clusters, federal and contractor computing along the I-79 corridor, and the campus-scale halls proposed under the 2025 Power Generation and Consumption Act. Each brings a different kind of liquid cooling job, from a single row in an existing building to a plant built for hundreds of megawatts.
West Virginia University’s research computing group runs Dolly Sods, a cluster deployed in 2023 under a National Science Foundation instrumentation award in which every compute node carries NVIDIA graphics processors, and which is aimed at machine learning and artificial intelligence research. The university also runs the general-purpose Thorny Flat cluster, which it describes as near the end of its life, and plans a successor named Harpers Ferry. Researchers at other West Virginia colleges and universities have access to these systems, so their cooling serves the whole state’s research base.
North central West Virginia also hosts the NASA Katherine Johnson Independent Verification and Validation Facility in Fairmont and the FBI’s Criminal Justice Information Services Division in Clarksburg, along with the contractor offices that support them. Those are market facts about where technical computing work sits in the state; they show why enterprise and contractor rooms along I-79 keep adding density.
Campus projects bring the biggest shift in scale. A West Virginia high impact data center under the 2025 law carries at least 90 MW of critical IT load, and buildings designed for that load today are drawn around liquid-cooled rows, with air handling sized for the share of heat that still leaves through fans, memory and power supplies.
| Setting | Typical starting point | Liquid cooling approach | Main constraint |
|---|---|---|---|
| University research cluster | GPU nodes in an existing campus data room | In-row CDU feeding cold plates, or rear doors on mixed racks | Tie-in to a campus chilled water system already serving other buildings |
| Federal contractor or enterprise room | Raised floor room cooled by CRAH units | Rear-door heat exchangers first, cold plates as hardware turns over | Security rules on access, and work inside an operating room |
| Hospital or state agency room | Small room on a building chilled water loop | Rear doors or a small CDU on the building loop | Building loop temperature set for comfort cooling, often colder than liquid loops need |
| Campus-scale hall under HB 2014 | Greenfield building on a microgrid or grid-fed campus | Row CDUs or facility-scale CDUs feeding direct-to-chip racks | Phasing, pump power continuity on site generation, and winter operation of dry coolers |
Matching ASHRAE W classes to West Virginia weather
The ASHRAE W classes set the warmest facility water a liquid-cooled server accepts, and West Virginia weather lets dry coolers meet the warmer classes for most of the year. The 2021 Thermal Guidelines define classes W17, W27, W32, W40 and W45 by their maximum facility supply temperature in degrees Celsius, plus W+ above 45 C. In Fahrenheit, W27 is 80.6 F and W32 is 89.6 F.
A dry cooler returns water some degrees warmer than the outdoor air, a margin called the approach. Taking a 10 F approach as an example, a W32 loop runs on dry coolers alone whenever outdoor air is at or below about 80 F, and a W27 loop whenever it is at or below about 70 F. NOAA’s 1991 to 2020 normals for Morgantown show an average daily high of 80 F or below in nine months of the year, and even July nights average 63.8 F.
| ASHRAE class | Maximum facility supply | Outdoor air needed for dry coolers alone | West Virginia picture from NOAA normals |
|---|---|---|---|
| W17 | 62.6 F | About 53 F or below | Dry coolers carry winter and cool nights; chillers run most of the summer |
| W27 | 80.6 F | About 70 F or below | Morgantown’s average daily high stays under 70 F from October through April |
| W32 | 89.6 F | About 80 F or below | Morgantown’s average high exceeds 80 F only in June, July and August; Snowshoe’s July high averages 70 F |
| W40 | 104 F | About 94 F or below | Morgantown reaches 90 F on 13.2 days a year on average, so dry operation covers nearly every hour |
| W45 | 113 F | About 103 F or below | Dry operation year-round, with return water warm enough to heat buildings |
The class the IT hardware accepts sets the ceiling, and the owner’s choice of approach and redundancy sets the plant. Paul Industries sizes the dry coolers and any trim cooling for the class the server vendor states, then checks the selection against the site’s own summer extremes, since a hall in the Kanawha Valley at Charleston, where July normal highs reach 86 F, needs more trim capacity than one at Canaan Valley, where they average 77 F.
Keeping warm water loops stable through a West Virginia winter
Warm water loops in West Virginia face a winter problem that hot-climate designs never meet: dry coolers can chill the facility water far below the temperature the CDUs and servers want. Morgantown averages 101.8 nights a year at or below freezing, and highland sites see January lows in the teens. Without control, a dry cooler on such a night returns water near the outdoor temperature, which wastes the warm water design and risks condensation inside the hall.
The control answer is a minimum supply temperature held by fan speed, coil bypass and three-way mixing at the plant, so the CDUs always receive water within a narrow band. The freeze answer is a choice between running glycol through the whole facility loop or confining it to an outdoor loop behind a plate and frame heat exchanger. A glycol-free indoor loop keeps the CDU primary side on treated water, with better heat transfer and simpler chemistry, at the cost of one more exchanger approach.
Summer brings the opposite risk. Kanawha and Ohio valley air in July carries enough moisture that a cold plate or rear door fed with water below the room dew point sweats. CDUs hold their secondary supply above the dew point measured in the white space, and the facility controls keep the primary supply high enough to let them.
Reusing rack heat in a heating-dominated climate
Rack heat reuse makes more sense in West Virginia than in most data center markets because the climate needs far more heating than cooling. NOAA’s normals for Morgantown record 4,964 heating degree days against 930 cooling degree days. A liquid-cooled hall returning water in the W40 or W45 range delivers heat at a temperature that can warm office space, maintenance shops, greenhouses or a campus heating loop for much of the year.
The engineering pieces are a heat exchanger between the data center return and the heating loop, a control valve arrangement that gives the data center priority so the servers never depend on a heating customer, and metering so the owner sees how much heat leaves the site. On a university campus the same approach can feed an existing hot water system. Paul Industries designs and installs the heat recovery exchangers, piping and controls as part of the liquid cooling scope.
Data center liquid cooling vs air cooling in existing West Virginia rooms
Retrofitting an existing West Virginia server room for liquid cooling starts with what the building already provides: the chilled water temperature on the loop, the structural rating of the floor, the routes available for new pipe, and the electrical capacity for CDU pumps. University, hospital and state agency rooms in Morgantown, Huntington and Charleston usually sit on a building or campus chilled water system run at comfort-cooling temperatures, which is colder than a liquid loop needs and often shared with occupied space.
Moving these rooms from air to liquid is rarely an all-or-nothing choice. A common path is rear-door heat exchangers on the densest racks first, which keeps the room’s air system intact while removing most of the heat at the rack, followed by cold plate racks fed from an in-row CDU as hardware is replaced. Each step adds pipe that is pressure tested, flushed and filled before any server connects. Paul Industries plans the routes overhead or under the floor, cuts in valved tees during scheduled outages, and works around the room’s operations so it keeps running.
Piping, pressure testing and cleanliness on the technology loop
Piping for a technology cooling loop in West Virginia follows the mechanical code the city or county has adopted through the State Building Code, 87 CSR 4, together with the owner’s specification and the CDU and server manufacturers’ requirements. The International Mechanical Code calls for hydronic piping to be tested hydrostatically at one and a half times the maximum design pressure, with a 100 psi minimum, held at least 15 minutes. Some CDUs, manifolds and quick disconnects carry lower pressure ratings than traditional facility piping, so those components are isolated or tested separately within their ratings.
Cleanliness matters more on the technology loop than anywhere else in the plant, because cold plate channels are narrow and quick disconnects foul easily. Paul Industries builds the loops in stainless steel or the owner’s specified material, flushes them to a measured filter result before the CDUs connect, fills them with treated or deionized water and the specified inhibitor or glycol, and records each step. Fill water quality is the same discipline as the ultrapure water systems in West Virginia page describes for process plants. The data center commissioning in West Virginia page covers testing the loops under heat load.
State licensing law applies to the work as well. Heating, ventilating and cooling work in West Virginia falls under W. Va. Code 21-16 and the Division of Labor’s rule 42 CSR 34, which tie the work to the Labor Commissioner’s licensing program, with exemptions the statute lists.
Pumps, power and the microgrid
CDU pumps are the most time-critical load in a liquid-cooled hall, because cold plates hold very little coolant and a stopped pump lets chip temperatures climb within moments. On a grid-fed hall the pumps run from UPS-backed power or carry their own ride-through. On a campus powered by an on-site microgrid, as the 2025 law allows, the generation plant itself is the utility, so the pump power design has to cover a generator trip and the restart that follows.
Typical answers are redundant CDU pumps on separate power paths, UPS feeds sized for the pumps and controls, and a facility loop with enough volume and buffer tank capacity to keep supply temperature stable while chillers or dry cooler fans recover. Paul Industries builds the pump sets, buffer tanks and controls, and coordinates their power with the electrical design of the campus. Owners comparing the full mechanical package for a microgrid campus will find it on the data center mechanical contractors in West Virginia page.
Phasing a West Virginia high impact data center for liquid cooling
Phasing a West Virginia high impact data center for liquid cooling means building the facility water backbone for the full campus while installing CDUs, manifolds and rack connections only as each block of IT load arrives. A building carrying 90 MW of critical load is rarely filled at once, and the server generation that fills its last hall is unknown when the first one opens, so the plant has to leave room for warmer or colder water classes than the first tenant uses.
Practical steps follow from that. Facility mains are sized for the final flow, with valved and capped branches at every future row so later CDUs connect without draining a live loop. Pump sets and dry cooler banks are added in modules matched to each phase. Space and connections for trim chillers are kept even where the first hardware runs dry year-round, because a later generation of servers may ask for a cooler class. Each new row is pressure tested, flushed and filled on its own before it opens to the live system.
| Element | Built with the first phase | Added with later phases |
|---|---|---|
| Facility water mains | Full-size headers with valved, capped branches | Branch extensions to new rows |
| Heat rejection | Dry cooler banks and pads for the first block, yard space reserved | Additional banks, trim chillers if a cooler class is needed |
| Pumping | Header connections and pump pads for all modules | Pump modules matched to each load step |
| CDUs and manifolds | Units for the first rows only | Units chosen for the hardware of each new tenant |
| Controls | Plant control system with room for future points | New CDU and rack integrations, retested at each step |
Keeping coolant healthy after turnover
Coolant health after turnover decides how long cold plates and quick disconnects last, so a West Virginia liquid cooling system needs a maintenance program from its first month. The program samples the technology loop for conductivity, pH, inhibitor level, glycol concentration and biological growth, changes or cleans CDU filters on a schedule set by measured pressure drop, and checks every quick disconnect and hose during planned maintenance windows.
Make-up water deserves the same attention as the original fill. Small top-ups with untreated water dilute inhibitors and bring in hardness, so the program keeps a supply of treated fill water on site and logs every addition. Paul Industries provides the maintenance, sampling and repair for the loops it installs and for existing systems, with records that support the CDU and server warranties.
What does data center liquid cooling cost in West Virginia?
The cost of data center liquid cooling in West Virginia depends on the number of racks and CDUs, the facility water class, whether the work is a retrofit inside an operating room or a new hall, and how far the plant can run on dry coolers. Energy is where West Virginia’s climate pays back. If moving 1 MW of IT load from air cooling to liquid cooling cuts mechanical overhead by 0.10 of PUE, the hall saves 876,000 kWh a year, worth about $68,400 at the EIA’s 2024 West Virginia industrial average of 7.81 cents per kWh or about $101,800 at the commercial average of 11.62 cents.
| Driver | Effect on price | What to send |
|---|---|---|
| Rack count and density | Sets CDU count, manifold length and hose and quick disconnect quantities | Rack layout and kilowatts per rack, now and at full build |
| Facility water class | Warmer classes shrink chillers and grow dry cooler hours | Server vendor’s stated W class and supply limits |
| Retrofit or new build | Live-room work adds phasing, hot work control and off-hours shifts | Room drawings, outage windows, access rules |
| Winter strategy | Glycol in the whole loop or an outdoor glycol loop behind an exchanger | Site elevation and the owner’s preference on indoor glycol |
| Heat reuse | Adds exchangers, controls and metering, and earns back heating fuel | Heating loads on the site and the water temperatures they use |
| Power arrangement | Microgrid campuses need pump ride-through and buffer volume | One-line diagram and UPS plan |
Paul Industries gives a budget range from comparable scope once the rack plan and water class are known, then a firm price when the design is fixed.
Who installs data center liquid cooling in West Virginia?
Paul Industries installs data center liquid cooling in West Virginia, covering design, supply of CDUs, manifolds, rear doors and dry coolers, fabrication of the piping, installation, flushing, filling, testing, startup and maintenance under one contract. Owners looking for one firm to take the rack loop and the plant together get one accountable team for both, with the records to support the server and CDU warranties.
Liquid cooling arrangements differ by setting, and Paul Industries delivers each of them: rear doors and in-row CDUs for existing rooms, row and facility CDUs for new halls, and immersion cooling where the hardware calls for it. The same practice serves Virginia, its headquarters state, through data center liquid cooling in Virginia, and the neighboring Pennsylvania liquid cooling and Maryland liquid cooling markets, as part of its East Coast coverage.
Liquid cooling from Paul Industries for West Virginia halls
Paul Industries delivers liquid cooling for West Virginia data halls, research clusters and enterprise rooms through supply-only packages, design-build systems and complete installation. The scope runs from dry coolers, heat exchangers and pumps at the plant to CDUs, stainless headers, rack manifolds, rear doors and heat recovery, with flushing, fill, testing and maintenance records for each loop. Send the rack plan and the server vendor’s water requirements, and request a quote for liquid cooling in West Virginia.
Standards referenced: ASHRAE TC 9.9 Thermal Guidelines for Data Processing Environments (W classes) · International Mechanical Code, Section 1208 · West Virginia State Building Code, 87 CSR 4 · W. Va. Code 21-16 (heating, ventilating and cooling work) · ASME B31.9 · West Virginia Power Generation and Consumption Act (HB 2014, 2025)
Frequently asked questions
Who installs liquid cooling for research computing in Morgantown?
Paul Industries installs liquid cooling for research computing rooms in Morgantown, including GPU rows on campus chilled water, in-row CDUs, rear-door heat exchangers and the piping that ties them to an existing plant. Campus loops in Morgantown often run at comfort-cooling temperatures and serve other buildings, so Paul Industries plans each tie-in during a scheduled outage and sets controls so the research room and the rest of the campus each get the water temperature they need.
Does Paul Industries pipe direct-to-chip cooling for facilities in Fairmont, Bridgeport and Clarksburg?
Yes. Paul Industries pipes direct-to-chip cooling for enterprise, contractor and technology facilities in Fairmont, Bridgeport and Clarksburg along the I-79 corridor. The work covers CDUs, stainless headers, rack manifolds, flushing, fill and testing, plus the facility water connection. Rooms there often operate under strict access rules, so work is planned around escorts, badging and the owner’s change control, with every step recorded for the room’s operators.
Who provides liquid cooling for data centers in Charleston and the Kanawha Valley?
Paul Industries provides liquid cooling for data halls in Charleston, South Charleston and the Kanawha Valley, from rear doors in state agency and hospital rooms to cold plate rows in enterprise halls. Charleston’s July normals of 86 F and 66 F bring humid summers, so CDU supply temperatures are held above the room dew point and dry coolers are paired with trim cooling for the warmest afternoons.
How does a high-elevation site in Tucker County or the Allegheny highlands change a liquid cooling loop?
A high-elevation site changes a liquid cooling loop most at the outdoor end. Canaan Valley’s January normal low is 17 F and its July high 77 F, so dry coolers carry warm water classes almost year-round, while winter calls for glycol or an outdoor glycol loop behind a heat exchanger, snow-resistant coil placement and minimum supply temperature control. Lower air density at altitude also slightly reduces fan and coil capacity, which the selections account for.
Which ASHRAE W class suits a West Virginia hall cooled by dry coolers?
W32, with a facility supply limit of 89.6 F, suits most West Virginia halls cooled by dry coolers, because with a typical approach the coolers carry it alone whenever outdoor air is at or below about 80 F, which covers nine months of average afternoons at Morgantown. W27 needs trim cooling for more of the summer. W40 and W45 hardware runs dry nearly year-round and returns water warm enough to heat buildings.
Do data centers use liquid cooling in West Virginia today?
Yes. Liquid cooling in West Virginia runs today in research computing, enterprise and contractor rooms, often as rear-door heat exchangers or in-row CDUs added to air-cooled spaces, and it is the design basis for the campus-scale halls proposed under the 2025 microgrid law. West Virginia University’s Dolly Sods cluster, built with a GPU in every compute node, shows the kind of hardware driving the change.
Are data centers water cooled when they use direct-to-chip loops?
Direct-to-chip loops use water-based coolant, usually treated water or a propylene glycol mixture, in a closed circuit that never touches the electronics directly. The coolant flows through cold plates mounted on processors and returns to a CDU, which passes the heat to the facility water. In West Virginia that facility water usually leaves through dry coolers, so a water-cooled hall there consumes little or no water at the outdoor end.
How is condensation kept off cold plates during a humid Ohio Valley summer?
Condensation is kept off cold plates by holding the coolant supply above the dew point of the air in the white space. CDUs measure room temperature and humidity, calculate the dew point and raise their secondary supply setpoint when needed, while the facility controls keep primary water warm enough for the CDUs to do so. Ohio and Kanawha valley summers carry enough moisture that this control matters most from June through September.
What keeps a dry-cooled facility loop from running too cold in January?
A dry-cooled facility loop is kept from running too cold by a minimum supply temperature control: fans slow or stop, coil sections are bypassed, and a three-way valve mixes return water into the supply. Morgantown averages 101.8 nights a year at or below freezing, so without that control the loop would deliver water far colder than the CDUs need, wasting the warm water design and raising condensation risk indoors.
Can warm return water from liquid-cooled racks heat other buildings on a West Virginia campus?
Yes. Return water from W40 or W45 racks arrives warm enough to serve space heating loops, and West Virginia’s climate needs heat for most of the year, with 4,964 heating degree days at Morgantown. A heat exchanger, priority controls that protect the data center first, and heat metering complete the arrangement. Paul Industries designs and installs the exchangers, piping and controls with the liquid cooling system.
Which code sets the hydrostatic test for liquid cooling piping in a West Virginia building?
The International Mechanical Code, adopted through the West Virginia State Building Code, 87 CSR 4, in cities and counties that have adopted it, sets the hydrostatic test for hydronic piping: one and a half times maximum design pressure, at least 100 psi, held for at least 15 minutes. Components with lower ratings, such as some CDUs and quick disconnects, are isolated during the test and checked within their own limits.
Why do CDU pumps need ride-through power on a microgrid campus?
CDU pumps need ride-through power on a microgrid campus because a generator trip is the campus utility outage, and cold plates hold so little coolant that processors heat up within moments of a pump stop. UPS-fed pumps, redundant pumps on separate power paths and buffer volume in the facility loop keep coolant moving while generation recovers. Paul Industries builds the pump sets and buffer tanks and tests the transfer before servers go live.
Which fill water goes into a new liquid cooling loop in West Virginia?
A new technology cooling loop is filled with deionized or reverse osmosis water dosed with the inhibitor package or glycol the CDU and server manufacturers specify, never with untreated municipal or well water. West Virginia supplies vary from soft surface water to hard groundwater, and untreated fill leaves scale and deposits in cold plate channels. Paul Industries supplies or treats the fill water and records conductivity and chemistry at fill.
How much does liquid cooling save in energy for a West Virginia data hall?
Liquid cooling saves about 876,000 kWh a year for each megawatt of IT load if it cuts mechanical overhead by 0.10 of PUE, worth roughly $68,400 a year at West Virginia’s 2024 industrial average price or $101,800 at its commercial average, per EIA figures. The actual saving depends on the starting plant, the facility water class and how many hours dry coolers carry the load.
Which data center liquid cooling solutions does Paul Industries supply without installation?
Paul Industries supplies CDUs, rack manifolds, rear-door heat exchangers, dry coolers and prefabricated piping on a supply-only basis for West Virginia projects. It also offers design-build liquid cooling systems and complete installation from the facility plant to the rack, including flushing, fill, testing, startup and maintenance, so owners choose the route that fits their project and schedule.
When does a rear-door heat exchanger make sense in a West Virginia hospital or state agency room?
A rear-door heat exchanger makes sense in a West Virginia hospital or state agency room when a few racks have outgrown the room’s air cooling but the servers are still air-cooled. The door removes most of the rack’s heat at the source using building chilled water, often without changes to the CRAH units. Supply water is held above the room dew point, and the door piping is pressure tested and flushed before the coils go into service.
What should a West Virginia owner collect before a liquid cooling site survey?
Before a liquid cooling site survey, a West Virginia owner should collect the rack layout and planned kilowatts per rack, the server vendor’s coolant and W class requirements, room and floor drawings, the existing chilled water temperatures and capacity, electrical one-lines, and outage windows. With those, Paul Industries walks the routes, measures the tie-in points and returns a budget range, then a firm price once the design is set.
What happens to a liquid cooling loop when a highland site loses power in winter?
When a highland site loses power in winter, outdoor dry coolers and their piping stop circulating and start losing heat to air that can sit in the teens. Loops protected with glycol ride through without damage; loops on plain water need automatic drain-down valves or heat tracing on battery or generator power. Paul Industries designs the freeze protection for the site’s winter extremes and tests the drain or glycol arrangement before turnover.
Bringing liquid-cooled racks into a West Virginia data hall?
Send the rack layout, kilowatts per rack, the server vendor’s water class and the existing plant data. Call 201-450-8280 or request a quote.
