Paul Industries provides pressure vessel fabrication in Colorado for breweries, food and dairy plants, biotech and pharmaceutical producers, refineries, utilities and research campuses, designing and building ASME Section VIII vessels that are registered, documented and rated for the elevation where they will run. Colorado’s vessel rules sit in 7 CCR 1101-5, administered by the Division of Oil and Public Safety, and they set registration, repair and relocation requirements that a fabrication package has to satisfy. Paul Industries is headquartered at 256 Shore Drive, Kilmarnock, Virginia, and fabricates and installs vessels for plants across Colorado and in all 50 states.

Request a quote or call 201-450-8280

Headquarters 256 Shore Drive, Kilmarnock, Virginia
Colorado rules 7 CCR 1101-5, Division of Oil and Public Safety
Registration Fired and unfired vessels registered with the National Board (rule 1-9)
Repairs Welded repairs and alterations under the National Board R program (rule 1-11)
Used vessels Inspected before shipment to Colorado (rule 2-6)
Denver atmosphere About 12.1 psia, so full vacuum is a 12.1 psi differential
Reviewed November 2026

What is considered a pressure vessel under Colorado law?

Colorado law defines a pressure vessel in section 9-4-101(16.5) of the Revised Statutes as a container for the containment of pressure, either internal or external, whether the pressure comes from an outside source, from direct or indirect heat, or from both. That definition answers what is considered a pressure vessel for state purposes, and it includes vessels under vacuum because external pressure is named. The statute also fixes where the vessel ends: at the first circumferential joint of a welded end connection, the face of the first flange of a bolted connection, or the first threaded joint. Piping beyond that point falls under the piping codes instead.

Under the same section, the colorado boiler and pressure vessel code is the state’s reference document for building, setting, running and inspecting this equipment, and it takes in both the ASME code and the NBIC. Rule 1-7(a) brings boilers and pressure vessels within the scope of ASME Sections I, IV and VIII under the regulations, and rule 1-5 incorporates Section VIII Divisions 1, 2 and 3 for new construction together with Sections V and IX for examination and welding qualification. The design basis for a new vessel built for a Colorado site is therefore the ASME code the state has adopted, plus whatever the owner’s specification adds. The national scope of vessel work is on the pressure vessel fabrication page; this page covers what Colorado adds.

Colorado pressure vessel regulations that shape a new vessel

Colorado pressure vessel regulations put most of their weight on registration, documentation and repairs rather than on design rules of their own. Rule 1-9(b) requires every fired and unfired pressure vessel, regardless of code of construction, to be registered with the National Board, except vessels installed or reinstalled before April 30, 1999 and Section VIII Division 1 vessels marked with the “UM” designator before January 1, 2003. A new vessel built for a Colorado plant therefore ships with its Manufacturer’s Data Report filed with the National Board and its registration number on the nameplate.

Colorado requirements by vessel situation
SituationColorado ruleWhat the fabrication package includes
New ASME vessel for a Colorado plantRule 1-9(b) National Board registration; rule 1-5 ASME constructionDesign calculations, Manufacturer’s Data Report, registration number, nameplate, test record
Vessel built with an ASME code caseRule 1-5(d): director’s acceptance obtained firstCode case citation and acceptance letter before fabrication starts
Used or secondhand vessel brought into ColoradoRule 2-6: inspection before shipment; application to the director before installationInspection report, original data report, thickness survey, application
Welded repair or alterationRule 1-11: National Board R program, NBIC or API 510Repair or alteration report, procedures, examination and test records
Rerate to a higher pressure or temperatureRule 1-6: a nonphysical change is an alterationCalculations, alteration report and revised nameplate
Departure from the adopted codesRule 1-5(e): variance on the director’s formVariance application with the engineering basis

The table shows why the paperwork is planned with the drawings. A brewery that buys a used bright tank rated as a pressure vessel from another state, for example, needs the pre-shipment inspection under rule 2-6 before the truck leaves, and an application on file with the director before the vessel is set. Paul Industries plans those steps into the purchase and fabrication schedule.

Pressure vessel inspection in Colorado: what the state schedules and what the owner keeps

Pressure vessel inspection in Colorado follows a different pattern from boiler inspection, and owners moving equipment in from other states should know the difference before they budget. Rule 2-1 of 7 CCR 1101-5 sets certificate inspection intervals for power boilers, heating boilers, water heaters and jacketed steam kettles, and the fee schedule lists certificate inspections for those categories; it lists no recurring certificate inspection for unfired pressure vessels. Under rule 2-3, an owner who wants an outside look at an exempt vessel can ask in writing, and a state or special inspector examines it, reports any violations and charges the scheduled fee.

That leaves the in service pressure vessel inspection program largely with the owner. Plants in petroleum and chemical service work to API 510, which rule 1-5 incorporates for the inspection, repair, alteration and rerating of their vessels, and API 510 pressure vessel inspection intervals are set from corrosion rates and remaining life rather than a fixed calendar. Section 9-4-110.5 also lets larger operators run their own registered inspection organizations, keeping inspection records for every nonexempt vessel, documenting all repairs and sending the director an annual statement. Other plants follow the NBIC, their insurer’s requirements and the manufacturer’s recommendations. The question of how often do pressure vessels need to be inspected in Colorado is therefore answered vessel by vessel, from service, corrosion allowance and consequence of failure.

Pressure vessel inspection requirements by Colorado owner type
Owner and serviceGoverning practiceHow intervals are set
Refinery or chemical plantAPI 510, incorporated by rule 1-5Corrosion rate, remaining life and risk-based assessment
Registered owner-user inspection organizationC.R.S. 9-4-110.5 and NB-371The organization’s written program, reported annually to the director
Food, beverage and dairy plantNBIC and the insurer’s programService conditions, cleaning chemistry and vessel history
Biotech and pharmaceutical plantNBIC plus the site’s GMP equipment programCalibration and maintenance schedules tied to qualification
Compressed air receivers in any plantNBIC and manufacturer guidanceDrain condition, corrosion and relief valve testing

Paul Industries sets up the inspection basis with each new vessel: corrosion allowance, inspection openings, thickness monitoring locations and the records an inspector will want later. For air compressor pressure vessel inspection and repairs on receivers, the same records make the next decision straightforward. Where a vessel is found thinned or cracked, the repair follows rule 1-11 and the inspector’s acceptance; section 9-4-105 lets an inspector condemn an unsafe vessel until it is repaired or replaced.

Designing a Colorado vessel for elevation, vacuum and relief

Elevation changes the numbers on a Colorado vessel even though the ASME rules stay the same, because ratings are stated in gauge pressure while the physics runs on absolute pressure. Denver’s standard atmosphere is roughly 12.1 psia, which means a vessel pulled to full vacuum there sees an external differential of about 12.1 psi rather than 14.7. Full-vacuum vessels are usually specified for 15 psi external pressure, which covers either case; the benefit at altitude shows up in jacketed and partial-vacuum designs, where the true differential sets shell and stiffener sizes.

Relief sizing is where elevation catches out sea-level data. Gas and steam relieving capacity is proportional to the absolute relieving pressure, and that pressure is lower at altitude for the same gauge set point. A valve set at 15 psig and relieving at 10 percent overpressure sees about 31.2 psia at sea level and about 28.6 psia in Denver, roughly 8 percent less capacity through the same orifice. At a 150 psig set point the difference falls to about 1.4 percent. Paul Industries sizes relief devices with API 520 methods at the site’s atmospheric pressure, so low-pressure vessels such as brewery tanks, deaerators and CO2 receivers are protected at the elevation where they sit.

Effect of Denver elevation on common vessel design checks
Design checkSea levelDenver, 5,280 ft
Atmospheric pressure14.7 psia12.1 psia
Largest vacuum differential on a vessel14.7 psi12.1 psi
Absolute pressure at 15 psig set plus 10 percent overpressure31.2 psia28.6 psia
Gas relieving capacity, same orifice, 15 psig setBaselineAbout 8 percent lower
Gas relieving capacity, same orifice, 150 psig setBaselineAbout 1.4 percent lower
Water boiling point at an atmospheric vent212 FAbout 202 F

Two other checks follow from the same physics. Processes controlled on absolute pressure, such as vacuum evaporation, deaeration and solvent recovery, need instruments ranged and labeled clearly as absolute or gauge so operators do not mix them. And a vessel hydrostatically tested at a fabrication site at a different elevation is tested to a gauge pressure, which carries over; the test record states the gauge reading, the water temperature and the hold time so the inspector at the Colorado site can accept it.

Where Colorado plants use pressure vessels

Colorado plants use pressure vessels across brewing, dairy, life sciences, energy and utilities, and each sector brings its own materials and documentation. Breweries along the Front Range, from the Coors brewery in Golden to craft producers in Denver, Boulder and Fort Collins, run CO2 receivers, bright tanks and hot liquor vessels. Leprino Foods operates a cheese plant in Greeley where heat treatment, evaporation and cleaning systems use pressure-rated equipment. Agilent announced a $725 million expansion of its nucleic acid therapeutics manufacturing site in Frederick in 2023, the kind of biotech plant that needs ASME BPE finishes on its process vessels. Suncor’s Commerce City refinery, at about 98,000 barrels a day, inspects and repairs its vessels under API 510. These plants are named as market facts only.

Biotech and pharmaceutical vessels add electropolished interiors, sanitary nozzles, drainability and passivation records to the code package; the passivation services in Colorado page covers that finishing step, and high-purity water systems in Colorado covers the storage and distribution vessels in water systems.

When a tank becomes a pressure vessel

A tank becomes a pressure vessel under the ASME code once its design pressure passes 15 psi, internal or external: Section VIII Division 1 excludes vessels whose internal or external operating pressure does not exceed 15 psi, and below that line the API tank standards take over. API 650 covers welded atmospheric storage tanks with a small allowance for internal pressure, and API 620 covers large low-pressure tanks up to 15 psig. Brewery tanks, deaerators, flash tanks and solvent receivers often sit close to that boundary, and the choice decides which code, which inspector and which Colorado registration rules apply. Paul Industries settles the design pressure with the owner first, because a tank specified at 14 psig and a vessel stamped at 30 psig look similar on a drawing and differ in every document that follows. Plants buying pressure vessel and tank fabrication together get both sets of documents from one source.

At Colorado elevations the boundary also interacts with vacuum. A tank that can be pumped out or cooled with its vent blocked sees external pressure, and an atmospheric tank that collapses under vacuum fails long before 15 psi. Vent sizing, vacuum breakers and the design external pressure are set together, using the site’s 12 psia atmosphere rather than sea-level figures.

Cold weather and minimum design metal temperature

Minimum design metal temperature (MDMT) matters on Colorado vessels set outdoors, because Front Range nights fall below zero several times most winters and carbon steel loses toughness as it cools. ASME Section VIII Division 1 ties impact testing to material group, thickness and MDMT through the UCS-66 curves, so a thick carbon steel receiver or separator outside in Greeley, Fort Collins or the eastern plains may need impact-tested plate, a lower-temperature material grade or a coincident-pressure reduction to qualify. Paul Industries sets the MDMT from the site’s cold-weather data and the process upset cases, such as autorefrigeration when a gas or CO2 vessel is blown down, and records the basis on the data report.

Insulation, heat tracing and drain points are designed at the same time. A drain leg full of water on a compressed air receiver, a sight glass on a CO2 tank or an instrument tap on a separator are the parts that freeze first. Paul Industries places drains, traces and insulates the exposed connections and leaves a winterization note in the turnover package.

Fabrication sequence and inspection hold points

A Colorado pressure vessel moves through a fixed sequence of design, material control, welding, examination, testing and registration, and the Authorized Inspector under the ASME code signs off at agreed hold points. Paul Industries prepares calculations and drawings for owner approval, receives material against mill test reports, qualifies welding procedures and welders under ASME Section IX, fits and welds shells, heads and nozzles, examines welds under ASME Section V, heat treats where the code or service calls for it, tests, and completes the Manufacturer’s Data Report for National Board registration. Hold points typically fall at material review, fit-up of major seams, examination results and the pressure test.

Owners who compare asme pressure vessel manufacturers on price alone often miss the cost of a late document or a missing registration, which can hold a vessel on the dock. The turnover package from Paul Industries lists the data report, registration number, drawings as built, material certificates, welding and examination records, test record and relief device data sheets, indexed so an inspector or auditor finds each item quickly.

Installing a new vessel in an operating Colorado plant

Installing a new vessel in an operating Colorado plant is planned as carefully as its fabrication, because the setting, piping tie-ins and first fill happen around live production. Colorado has no single statewide building code for private industrial buildings; foundations, anchorage, platforms and building permits follow the code adopted by the city or county where the plant sits, and county building departments may also run their own contractor licensing under section 30-11-125. Paul Industries confirms the jurisdiction’s adopted code, wind and snow design values and permit steps before the foundation drawings are issued.

On site, the work runs from foundation and anchor bolt checks to rigging, setting and leveling, then nozzle alignment so piping loads stay within the allowable nozzle loads in the design report. Relief devices are installed with their discharge routed to a safe location, instruments are calibrated against their range in absolute or gauge units, and the vessel is cleaned and, for sanitary service, passivated before first use. Tie-ins to running systems are scheduled into planned outages with isolation, blinding and lockout agreed with plant operations. The final walk-down covers nameplate visibility, insulation, heat tracing, labeling and access for future inspection, and the owner receives the complete record set with the vessel’s National Board registration number on the cover sheet.

Shop-built, field-erected or skid-mounted: fabrication routes for Colorado

Fabrication routes for a Colorado vessel depend on its size, the access at the site and how much of the system can be assembled before delivery. Paul Industries offers each route below as supply-only, design-build or complete installation.

Pressure vessel and tank fabrication routes
RouteFitsDelivered with
Shop-fabricated ASME Section VIII Division 1 vesselReceivers, filters, separators, heat exchanger shells, process vesselsData report, National Board registration, nameplate, test record
Section VIII Division 2 designHigh-pressure or heavy-wall vessels where design-by-analysis saves materialUser’s design specification and a design report signed by a registered professional engineer
Skid-mounted vessel assemblyPump, filter and vessel packages for brewing, food and water treatmentVessel documents plus piping, instruments and controls tested before shipment
Field-erected vesselVessels too large to ship by road into mountain or urban sitesField welding records, examination, test and final documents
Repair, alteration or rerateExisting vessels with damage or new dutyR program report, calculations and revised nameplate

Road access matters in Colorado: mountain passes, tunnels and urban streets limit what can be delivered in one piece, so very large vessels are sometimes built in sections and joined at the site. Paul Industries checks the delivery route before setting the shipping split.

What does pressure vessel fabrication in Colorado cost?

The cost of pressure vessel fabrication in Colorado is driven by material and thickness, diameter and length, design pressure and temperature, nozzle count, internals, surface finish, examination extent, post-weld heat treatment and the documentation package. Stainless and duplex grades, electropolished interiors and 100 percent radiography raise cost; carbon steel receivers with standard nozzles sit at the other end. Delivery splits for large vessels, field welding and installation are priced separately so the owner can compare routes.

Public work adds its own cost basis: when a Colorado state agency awards a public project worth $500,000 or more, the procurement code at sections 24-92-202 and 24-92-203 sets prevailing wage rates for the installation labor. Paul Industries gives a budget range from comparable vessels once it has a process data sheet or sketch, then a firm price on the approved design.

Who fabricates pressure vessels in Colorado?

Paul Industries fabricates pressure vessels for Colorado plants, from small CO2 and air receivers to jacketed process vessels, separators and heat exchanger shells. Owners looking for pressure vessel fabricators or pressure vessel manufacturers Colorado projects can rely on get design calculations, ASME construction, National Board registration, installation and startup under one contract, with pressure vessel fabrication Denver, Boulder, Colorado Springs and Western Slope plants all handled the same way. Paul Industries takes work across Colorado, across the Southwest and in all 50 states. Its headquarters-state work is on the pressure vessel fabrication in Virginia page, and plants with sites elsewhere can compare pressure vessel fabrication in Texas and pressure vessel fabrication in California.

Colorado pressure vessels from Paul Industries

Paul Industries designs, fabricates, supplies, installs, tests and repairs pressure vessels for Colorado plants, and it builds the tanks, piping and boilers connected to them. Owners can buy a vessel supply-only, take a design-build package with calculations and drawings, or have Paul Industries install the vessel complete with piping, instruments, relief devices and hydrostatic testing. Formerly based in northern New Jersey, then Pennsylvania, Paul Industries now runs its vessel projects from its Kilmarnock, Virginia headquarters. The Colorado plant services overview lists the full range, and related Colorado work includes tank fabrication in Colorado, industrial welding services in Colorado and boiler repair in Colorado. Send the process data sheet, design conditions and site elevation, and request a quote.

Standards referenced: Colorado boiler inspection statute, C.R.S. 9-4 · 7 CCR 1101-5, Boiler and Pressure Vessel Regulations · ASME Boiler and Pressure Vessel Code, Section VIII Divisions 1, 2 and 3 · ASME Section IX · ASME Section V · National Board Inspection Code (NBIC) · API 510 · API 520

Frequently asked questions

Who are the ASME pressure vessel fabricators serving Colorado plants?

Paul Industries is one of the ASME pressure vessel fabricators serving Colorado plants, building Section VIII vessels for brewing, food, dairy, biotech, refining and utility service. Each vessel ships with design calculations, a Manufacturer’s Data Report, National Board registration as rule 1-9 of 7 CCR 1101-5 requires, a nameplate and a test record. Paul Industries also installs and starts up the vessels it builds.

When does API 510 pressure vessel inspection apply at a Colorado plant?

API 510 pressure vessel inspection applies to vessels used in the petroleum and chemical processing industries, which rule 1-5 of 7 CCR 1101-5 incorporates for installation, inspection, repairs, alterations, rating and rerating. Refineries, chemical plants and similar sites in Colorado set inspection intervals from corrosion rate and remaining life under API 510. Paul Industries builds new vessels with the thickness monitoring locations and records that program needs.

Does Colorado require pressure vessel inspection colorado plants schedule every year?

Colorado’s inspection schedule in rule 2-1 sets certificate intervals for boilers, water heaters and jacketed steam kettles, and the fee schedule lists no recurring certificate inspection for unfired pressure vessels. An inspector will examine an exempt vessel on the owner’s written request under rule 2-3. Owners set in-service intervals from API 510, the NBIC, insurer requirements and service conditions, and Paul Industries supplies the baseline data for that program.

What pressure vessel inspection services does a new Colorado vessel need before startup?

A new vessel needs the examinations its ASME code and specification call for, a pressure test, a final inspection by the Authorized Inspector under the code, and National Board registration of the data report. At the Colorado site, Paul Industries checks setting, nozzle loads, relief devices and instruments, and records a baseline thickness survey. Those pressure vessel inspection services give the owner a clean starting record for later in-service inspections.

Which pressure vessel inspection companies examine vessels under insurance in Colorado?

Boilers and vessels covered by insurance in Colorado are inspected by special inspectors employed by the insurance company who hold National Board commissions, by state inspectors, or by an owner-user inspection organization’s own commissioned inspectors under section 9-4-110.5. Paul Industries prepares vessels for those inspections, opens and cleans them, supports thickness and visual examinations, and carries out the repairs found under the National Board R program.

How are pressure vessels tested before they are installed in Colorado?

Pressure vessels are tested to the requirements of their ASME code, usually with a hydrostatic test at 1.3 times the maximum allowable working pressure for Section VIII Division 1, adjusted for temperature, or a pneumatic test where water cannot be used. The test is witnessed by the Authorized Inspector. Paul Industries records the gauge pressure, water temperature and hold time, so the record reads correctly at any Colorado elevation.

Can a used pressure vessel from another state be installed in Colorado?

A used pressure vessel can be installed in Colorado after it passes an inspection before shipment under rule 2-6 of 7 CCR 1101-5, carried out by a National Board commissioned inspector or one the director approves, and after the owner files an application with the director. Paul Industries collects the original data report, runs a thickness survey, checks relief devices and plans the inspection so the vessel can ship.

What is a boiler and pressure vessel inspection organization under Colorado law?

Section 9-4-110.5 lets a company that operates boilers or pressure vessels register as an owner-user inspection organization. It inspects its nonexempt equipment with qualified inspectors, keeps signed reports and repair records at the site, notifies the director of unsafe equipment and files an annual statement. A state certificate is still required for boilers it inspects. Paul Industries supplies vessel records in the format those programs use.

How does a rerate count under Colorado pressure vessel rules?

Colorado’s rule 1-6 defines an alteration to include nonphysical changes such as raising the maximum allowable working pressure, internal or external, or the design temperature. A rerate is therefore an alteration made under the National Board R program as rule 1-11 requires, with new calculations, an alteration report and a revised nameplate. Paul Industries checks thickness, nozzle reinforcement and relief capacity before proposing a rerate.

Why does relief valve sizing change for a vessel in Denver?

Gas and steam relieving capacity depends on the absolute pressure at the valve inlet, and Denver’s atmosphere is about 12.1 psia instead of 14.7. A valve set at 15 psig therefore relieves at about 28.6 psia in Denver against 31.2 psia at sea level, roughly 8 percent less capacity through the same orifice. Paul Industries sizes relief devices at site conditions, which matters most on low-pressure vessels.

Does Paul Industries handle pressure vessel fabrication Denver and Colorado Springs plants need?

Paul Industries handles pressure vessel fabrication for Denver, Aurora, Golden and Colorado Springs plants, as well as Boulder, Longmont, Fort Collins, Greeley and Pueblo sites. Vessels are designed at the site’s elevation, built to ASME Section VIII, registered with the National Board and installed with their piping and relief devices. Call 201-450-8280 with the design conditions and the site address to start a quote.

What do Western Slope plants around Grand Junction need from a pressure vessel supplier?

Plants around Grand Junction and the Western Slope work under the same Colorado rules as the Front Range, with delivery routes across mountain passes and tunnels shaping how a vessel is shipped. Paul Industries checks the route before setting the shipping size, splits large vessels for field joining when needed, and documents field welds and tests for the inspector. Process water, energy and food plants there get the same documentation package.

Are brewery bright tanks and CO2 receivers pressure vessels in Colorado?

A bright tank or CO2 receiver designed to hold internal pressure is a pressure vessel under section 9-4-101(16.5) when it falls within the ASME Section VIII scope, and rule 1-9 calls for National Board registration of fired and unfired vessels installed after April 30, 1999. Paul Industries designs brewery vessels to the pressure the process needs, sizes relief devices at the brewery’s elevation and supplies the registration paperwork.

What should a Colorado biotech plant specify for a process vessel?

A Colorado biotech plant should specify the ASME Section VIII design conditions, ASME BPE surface finish and drainability, material grade, nozzle list with sanitary connections, jacket or coil duty, agitator loads, cleaning and sterilization conditions, and the documentation package for qualification. Steam sterilization conditions are set in absolute terms at the plant’s elevation. Paul Industries builds the vessel, passivates it and supplies the turnover package.

How much time should a Colorado plant allow for a custom ASME vessel?

Schedule depends on material availability, design approval, fabrication complexity, examination and heat treatment, so Paul Industries sets dates once the design conditions and drawings are agreed. Owners shorten the path by fixing nozzle orientations and design conditions early, approving drawings promptly and lining up any code case acceptance under rule 1-5(d) before fabrication starts. Installation is planned around the plant’s shutdown window.

Who repairs a cracked or thinned pressure vessel in Colorado?

Paul Industries repairs cracked and thinned pressure vessels in Colorado under the National Board R program as rule 1-11 requires, following the NBIC or API 510. The work runs from the inspector’s findings to a repair plan, qualified welding, examination, pressure test and a repair report filed with the vessel’s records. Where repair is uneconomic, Paul Industries builds and installs a replacement vessel.

What should be sent to quote a pressure vessel for a Colorado site?

Send the design pressure and temperature, including any vacuum, the fluid and corrosion allowance, volume and dimensions, nozzle list, internals, material and finish preferences, the site elevation, and any owner specification or code case. Photographs of the setting area and delivery route help on larger vessels. Call 201-450-8280 or request a quote, and Paul Industries returns a budget range followed by a firm price.

Specifying a pressure vessel for a Colorado plant?

Send the design conditions, process fluid, nozzle list, site elevation and any owner specification. Call 201-450-8280 or request a quote.