Paul Industries provides pressure vessel fabrication in Texas, designing, building, testing and setting ASME Section VIII vessels for refineries, chemical plants, LNG terminals, gas plants and life science sites from the Ship Channel to the Permian Basin. Texas has no state inspection program for unfired pressure vessels, so the ASME Code, the plant’s process safety program and the insurer carry the weight that a state chief inspector carries elsewhere. Paul Industries, headquartered at 256 Shore Drive in Kilmarnock, Virginia, builds every vessel with the code records a Texas owner’s mechanical integrity program needs from day one.

Request a quote or call 201-450-8280

Headquarters 256 Shore Drive, Kilmarnock, Virginia
Vessel program None for unfired vessels; Chapter 755 exempts them (755.022)
Still under TDLR Unfired steam boilers and process steam generator drums
Gulf Coast refining About one-third of US crude refining capacity is in Texas (EIA)
Newest LNG export Golden Pass produced first LNG in March 2026
Reviewed November 2026

Who regulates pressure vessels in Texas?

Texas regulates boilers through Health and Safety Code Chapter 755 and TDLR, but Section 755.022 states that the chapter does not apply to pressure vessels or process steam generators, apart from the steam collection or liberation drums of process steam generators. An air receiver, reactor, separator, accumulator, column or heat exchanger shell at a Texas plant therefore carries no state registration number or state certificate of operation.

The rules that do apply come from other places. Federal OSHA’s process safety management standard, 29 CFR 1910.119, requires a mechanical integrity program for pressure vessels in covered processes, with inspection and testing that follows recognized and generally accepted good engineering practice, which on the Gulf Coast means the ASME Code for construction and API 510 for inspection, repair, alteration and rerating. EPA’s risk management program rule in 40 CFR Part 68 adds parallel duties at facilities holding regulated substances above threshold. The owner’s insurer, the purchase order and the corporate engineering standard then name the code edition, the stamp the vessel must carry and the inspector who witnesses the work.

Texas pressure vessel regulations, in that sense, are written by each owner. That arrangement puts the burden on the specification. A vessel ordered for Texas without a stated code, design data and inspection plan has nothing outside the contract to hold it to a standard, which is why Paul Industries starts every order from a complete data sheet and builds to the ASME Section VIII division the owner names.

Texas pressure vessel law: what Chapter 755 covers and what it leaves to the code

Texas pressure vessel law is short: the state reaches only those vessels that count as boilers. Three groups stay inside the TDLR program, and the line between them and ordinary process vessels decides who inspects a repair and which paperwork follows it.

  • Unfired steam boilers. An unfired pressure vessel in which steam is generated is an unfired steam boiler under Section 755.001, unless it is an evaporator, a heat exchanger or a vessel making steam from process heat. Rule 65.608 lets these be built to ASME Section I or Section VIII Division 1, 2 or 3, within jurisdictional limits, and they are registered, inspected yearly and certificated like power boilers.
  • Steam drums of process steam generators. The drum on a waste heat unit is inspected annually like a power boiler, with extensions to 120 or 144 months depending on whether it was built before or after 1970, while the exchanger it serves stays outside the program.
  • Autoclave vessels, now exempt. Since September 1, 2025, Senate Bill 1185 has exempted unfired pressure vessels in an autoclave, along with small boilers that are part of FDA-regulated medical devices.

Section 755.028 also lets TDLR run a special inspection service, including the surveys a fabricator undergoes for authorization to build or repair boilers and pressure vessels. That service concerns the fabricator’s quality program, not the vessel in the field. Boiler-side work on drums and unfired steam boilers is covered on boiler repair in Texas.

Which rules reach which vessels at a Texas plant
EquipmentState programWhat governs construction and inspection
Reactor, column, separator, accumulator, filter housingNone (755.022)ASME Section VIII as specified; API 510 and the plant’s PSM program in service
Shell-and-tube exchanger, evaporator, waste heat exchangerNone for the exchangerASME Section VIII and TEMA; owner’s mechanical integrity program
Steam drum on a process steam generatorTDLR boiler programAnnual certificate inspection; NBIC for repairs; extension to 120 or 144 months
Unfired steam boilerTDLR boiler programASME Section I or VIII within Rule 65.615 limits; annual certificate inspection
Compressed air receiverNoneASME Section VIII; OSHA 1910.169 for drains, gauges and safety valves
Autoclave pressure vesselNone since September 1, 2025ASME Section VIII; FDA device rules where it is part of a medical device
Atmospheric storage vessel of 21,000 gallons or more at a refinery, chemical plant or terminalTCEQ Chapter 338 (not a pressure vessel above 0.5 psig)API 650 and API 653 as incorporated by the rule

Pressure vessel inspection requirements, Texas plants and the PSM program

Pressure vessel inspection requirements at Texas plants come from the owner’s mechanical integrity program rather than from a state schedule, and for a covered process OSHA expects that program to follow recognized practice. On the Gulf Coast that practice is API 510, which caps the interval between internal or on-stream inspections at half the remaining life or 10 years, whichever is less, unless a risk-based inspection assessment supports a different interval, and sets external visual inspections at no more than five years or the internal interval, whichever is shorter.

Who inspects pressure vessels in Texas service, then, is the owner’s authorized inspector working under API 510, or the insurer’s inspector where the policy calls for it. For a new vessel, the inspection that matters is the one during fabrication: the authorized inspector’s review of materials, welding procedures, examinations and the hydrostatic test before the Code stamp is applied. Who approves pressure vessels at that stage is the authorized inspector employed by an authorized inspection agency, signing the manufacturer’s data report, and the owner’s engineer accepting the design calculations. Paul Industries plans hold points for both so that the turnover package matches what the owner’s inspection group will load into its records system.

The PSM standard’s quality assurance clause also reaches fabrication: OSHA expects the owner to confirm that new equipment is suitable for the process and built to the design. That is why Texas owners ask for material test reports, positive material identification on alloy parts, weld maps and NDE records along with the nameplate, and why the vessel’s first API 510 baseline thickness readings are often taken before it leaves fabrication.

Designing a vessel for Gulf Coast service

Gulf Coast service shapes vessel design in three ways: the process chemistry of refining and petrochemicals, the hot, humid and salty atmosphere outside the shell, and hurricane wind on tall columns and stacked exchangers. The data sheet has to address all three before the first thickness calculation.

Damage mechanisms that drive Texas vessel design
Service or exposureDamage mechanismDesign and fabrication response
Wet H2S in refinery unitsSulfide stress cracking, hydrogen blistering and HICMaterials and hardness controls to NACE MR0103, HIC-tested plate where specified, PWHT
Amine and caustic serviceStress corrosion cracking of carbon steel weldsPostweld heat treatment of welds and attachments, specified by the owner’s standard
Chlorides in cooling water or coastal airPitting and chloride stress corrosion cracking of 304 and 316 stainlessDuplex or higher alloy selection, coating and insulation detailing
Insulated vessels in humid airCorrosion under insulationCoating under insulation, sealed penetrations, inspection ports, insulation supports that shed water
Cryogenic LNG and NGL serviceBrittle fracture at low temperatureImpact-tested materials, stainless or nickel steels, minimum design metal temperature on the data sheet
Tall columns on the coastWind load and vortex sheddingShell, skirt and anchor design to the site wind speed; strakes or dampers where needed

Material lead times follow from those choices. Impact-tested plate, HIC-tested plate, duplex, nickel alloys and clad plate all carry longer mill schedules than standard carbon steel, so Paul Industries confirms the material plan with the owner before releasing drawings, and offers equivalents where an alternate grade meets the same design basis.

Refining, chemical and LNG vessels along the Texas coast

The Texas coast is where most of the state’s vessel demand sits: Texas holds about one-third of US crude refining capacity, and its petrochemical plants, gas processing and LNG export terminals add thousands of separators, drums, columns and exchangers that need replacement, rerating or new capacity every turnaround cycle.

Pressure vessel fabrication, Houston, TX and the Ship Channel

Plants along the Houston Ship Channel in Pasadena, Deer Park, La Porte and Baytown order reactor vessels, knockout drums, flare drums, amine contactors and regenerators, and exchanger shells, usually against a turnaround date that cannot move. Because the Houston-Galveston-Brazoria area is in severe nonattainment for ozone, vessel changes that touch emissions, such as larger flash drums or new vents, are reviewed against the plant’s air permit early.

Beaumont, Port Arthur and the Sabine-Neches waterway

Refineries and petrochemical units around Beaumont, Port Arthur and Orange replace hydroprocessing separators, sour water drums and fractionation internals, and the LNG export terminal at Sabine Pass, Texas, where Golden Pass produced its first LNG in March 2026, has added cryogenic vessel work to the region.

Corpus Christi, Freeport and the Coastal Bend

Corpus Christi and Freeport combine refining, chemicals and LNG export, with chloride exposure on every outdoor shell, so alloy selection and coating systems get as much attention as wall thickness.

West Texas and the Permian Basin

Gas processing in the Permian Basin around Midland and Odessa uses inlet separators, slug catchers, amine units and NGL vessels, often as skid-mounted packages where the vessel and its piping are built and tested together. Produced water, condensate and amine services there bring their own corrosion allowances and sour service controls, and summer heat on unshaded equipment raises design temperatures for vessels that sit in the sun.

Sanitary and pharmaceutical vessels for Texas life science builds

Sanitary pressure vessels for Texas pharmaceutical plants are built to ASME Section VIII for pressure and ASME BPE for surface finish, cleanability and documentation, and the Houston area now has two large drug manufacturing builds at Generation Park in Harris County: Lilly’s $6.5 billion active ingredient site and Bristol Myers Squibb’s roughly $2.3 billion campus for small molecules, biologics and antibody-drug conjugates. Those are market facts about the region; the vessel requirements are the same for any GMP site.

A GMP vessel adds requirements a refinery drum never sees: electropolished or mechanically polished product-contact surfaces with a specified roughness average, sloped and drainable heads, sanitary nozzles and spray devices sized for clean-in-place coverage, jackets for heating and cooling, and a turnover package that feeds installation qualification. Paul Industries builds these vessels and ties them into validation and commissioning in Texas, so the vessel’s records are ready when the qualification protocol asks for them.

From data sheet to nameplate: how a Texas vessel order runs

A Texas vessel order runs through the same Code steps as anywhere in the country, but the owner’s specification fills the role the state plays elsewhere, so each step ends with a record the owner keeps.

Steps in a Texas vessel order and the record each produces
StepWhat happensRecord for the owner
Data sheet reviewDesign pressure and temperature, MDMT, corrosion allowance, service, code division, PWHT and NDE requirements confirmedApproved data sheet
Design calculations and drawingsShell and head thickness, nozzle reinforcement, wind and seismic loads, supports and lifting lugsCalculation package and general arrangement drawing for owner approval
MaterialsPlate, forgings, pipe and fittings received with mill certificates; alloy parts checked by PMIMaterial test reports and PMI log
WeldingQualified procedures and welders under ASME Section IX; weld map maintainedWPS, PQR, welder qualifications, weld map
Examination and heat treatmentRadiography or ultrasonic testing, magnetic particle or dye penetrant, PWHT where requiredNDE reports and heat treatment charts
Hydrostatic test and inspectionTest witnessed by the authorized inspector; Code stamp appliedManufacturer’s data report and nameplate rubbing
Shipping, setting and tie-inVessel shipped, set on its foundation, leveled, grouted and connectedSetting record, anchor bolt torque, baseline thickness readings

Large vessels add a logistics step. Heavy columns and reactors move to coastal sites by barge or under Texas oversize and overweight permits on the road, and the delivery route can limit diameter and length, so shipping is planned during design rather than after fabrication. Hydrostatic testing at site, where a vessel ships in sections, follows the methods on the hydrostatic testing page.

Relief protection when no state inspector checks it

Relief protection on a Texas vessel is checked by the owner’s process safety program and the authorized inspector at fabrication, not by a state inspector at an annual visit, so the sizing basis has to be right and documented from the start. ASME Section VIII requires every vessel to be protected against overpressure, and since the 2021 edition the construction, capacity certification and marking rules for relief devices sit in ASME Section XIII. Relief load cases such as blocked outlet, fire exposure, tube rupture in an exchanger and control valve failure are worked out under API 520 and API 521, which most Gulf Coast owners name in their standards.

The vessel’s design has to carry those cases. A fire case on an uninsulated drum sets a relief load that depends on wetted area, so the nozzle for the relief valve, the inlet line pressure drop and the discharge to flare or atmosphere are designed with the vessel rather than added later. Texas plants inspect relief devices on intervals set by API 576 practice and their own experience, and Paul Industries delivers the relief sizing basis with the vessel so the first inspection has something to check against.

Skid packages and exchanger shells

Skid packages are how a large share of Texas vessels arrive: separators, filter coalescers, amine contactors and chemical injection drums mounted on structural steel with their piping, valves and instruments, built and tested before shipment. The vessel is still stamped to Section VIII, while the interconnecting piping is built to ASME B31.3, and the skid’s structural design has to handle lifting, transport and the site’s wind loads.

For a replacement pressure vessel, Houston plants usually want the new unit to match the old footprint, nozzle orientation and elevations so the tie-in piping can be reused, and Paul Industries surveys the existing vessel and its connections before the drawings are issued. Shell-and-tube exchanger shells, channels and covers follow the same Section VIII rules with TEMA class requirements on top, and a retube or rebundle is often paired with a new shell where wall loss has reached its limit.

Repairs, alterations and rerates on vessels in Texas service

Repairs and alterations on Texas vessels follow API 510 under the owner’s mechanical integrity program, or the National Board Inspection Code where the owner or insurer specifies it, because no state rule sets a repair procedure for unfired vessels. Can pressure vessels be welded after years in service? Yes, when the repair procedure, the material condition and any required postweld heat treatment are worked out first, and the owner’s inspector authorizes the work and accepts the result.

A rerate to a higher pressure or temperature needs new calculations against the original code of construction, a check of corrosion allowance consumed, often a pressure test, and an updated nameplate and data report. Alterations such as new nozzles, manways or jackets change the pressure boundary and are treated the same way. Paul Industries supplies repair and rerate calculations, fabricates replacement heads, shell courses and nozzle assemblies, makes the weld repairs and leaves records that match the owner’s API 510 files. Welding procedures and examinations for this work are covered on industrial welding services in Texas.

Coatings, insulation and storage before a Texas vessel enters service

Coatings, insulation and site storage decide how a carbon steel vessel looks after its first Texas summer, and corrosion under insulation is the damage mechanism that most often surprises owners on the coast. A vessel that will be insulated gets an immersion-grade or high-temperature coating on the shell before the insulation goes on, sealed insulation terminations at nozzles, supports and ladder clips, and inspection plugs placed where the owner’s API 510 program wants thickness readings.

Stainless vessels need their own care. Austenitic stainless exposed to coastal chlorides and wet insulation can crack, so owners specify low-chloride insulation, coatings on stainless operating in the susceptible temperature range, and protection from carbon steel contamination during fabrication and storage. Vessels that sit at site before setting are stored with nozzles blanked, desiccant or nitrogen in sensitive services, and supports that keep water off the shell. Paul Industries ships every vessel with its preservation instructions and checks the condition at receipt, before it is set.

What does pressure vessel fabrication in Texas cost?

The cost of pressure vessel fabrication in Texas is driven by material, wall thickness, diameter and length, the number and size of nozzles, internals, postweld heat treatment, the extent of radiography or ultrasonic testing, surface finish for sanitary service and the schedule, so prices come from the data sheet rather than from a weight or volume rule of thumb. Alloy and clad vessels, impact-tested materials and full radiography can multiply the cost of an otherwise identical carbon steel drum.

Paul Industries offers a budget range from comparable vessels once the data sheet is in hand, then a firm price when the design is fixed. Supply-only vessels, design-build packages with the piping and supports, and complete installation including setting and tie-in are all priced on that basis.

Who designs and builds ASME pressure vessels in Texas?

Paul Industries designs, fabricates, tests, supplies and installs ASME Section VIII pressure vessels for Texas plants, including drums, separators, columns, reactors, receivers, heat exchanger shells and sanitary process vessels. Among pressure vessel manufacturers in Texas markets, buyers compare the same things: the design calculations offered, the inspection and test plan, the material traceability and the turnover records, and Paul Industries puts all four in the proposal.

Vessel orders often come with related scope: atmospheric storage on tank fabrication in Texas, interconnecting lines on process piping in Texas, and exchangers on the heat exchangers page. The national pressure vessel fabrication page covers code divisions, testing and nameplates in more depth.

Vessels from Paul Industries for Texas plants

Headquartered at 256 Shore Drive in Kilmarnock, Virginia, and formerly based in northern New Jersey and then Pennsylvania, Paul Industries is an East Coast contractor that builds vessels for plants across Texas, in every other state and at plants outside the United States (see international work). Owners with plants in the headquarters state can see pressure vessel fabrication in Virginia, and those building in the Southeast can compare pressure vessel fabrication in Georgia. The Texas overview and the Gulf Coast page cover the rest of Paul Industries’ work in the state and region.

For pressure vessel fabrication in Texas, Paul Industries designs to the owner’s data sheet, builds and tests to ASME Section VIII, documents every step for the mechanical integrity program, ships and sets the vessel and connects it to the plant. To start, send the data sheet or process conditions and your required date, and request a quote.

Standards referenced: ASME Boiler and Pressure Vessel Code Section VIII Division 1 and Division 2 · ASME Section II and Section V · ASME Section IX · ASME BPE · National Board Inspection Code (NBIC) · API 510 · NACE MR0103 / ISO 17945 · OSHA 29 CFR 1910.119 (process safety management) · OSHA 29 CFR 1910.169 (air receivers) · EPA 40 CFR Part 68 · Texas Health and Safety Code Chapter 755 · 30 TAC Chapter 338

Frequently asked questions

Who fabricates pressure vessels for Houston, Pasadena and Deer Park chemical plants?

Paul Industries designs and fabricates ASME Section VIII vessels for chemical plants and refineries in Houston, Pasadena, Deer Park, La Porte and Baytown, including knockout and flare drums, reactors, amine contactors and exchanger shells. Turnaround dates set most of these orders, so Paul Industries confirms materials and hold points with the plant’s inspection group at award and schedules the hydrostatic test well ahead of the outage.

Does Paul Industries build vessels for Corpus Christi and Freeport plants?

Yes. Paul Industries builds separators, drums, columns and exchanger shells for refineries, chemical plants and export terminals in Corpus Christi, Ingleside and Freeport. Coastal exposure shapes these orders: external coatings, coating under insulation, duplex or higher alloys where chlorides are present, and anchorage designed for the site wind speed are all set on the data sheet.

Which vessels do Beaumont and Port Arthur refineries replace during turnarounds?

Common replacements include hydroprocessing separators, sour water and amine drums, fractionator sections, reflux accumulators and exchanger shells that have reached their API 510 retirement thickness. Paul Industries builds replacements to the original design or a rerated basis, with wet H2S material controls and postweld heat treatment where the service calls for them, and plans delivery to the turnaround window.

Who builds sanitary pressure vessels for pharmaceutical plants going up around Houston?

Paul Industries builds jacketed, polished ASME Section VIII vessels to ASME BPE for pharmaceutical and biotech plants, including the Houston area where Lilly and Bristol Myers Squibb have announced large Generation Park sites. Each vessel ships with material traceability, surface finish records, weld documentation and drawings arranged for installation qualification.

What does 'Texas pressure vessel code' mean on a purchase order?

Texas has no state pressure vessel code, so the phrase usually means the ASME Boiler and Pressure Vessel Code edition and division the owner requires, often Section VIII Division 1, plus the owner’s own engineering standard. Paul Industries asks for the edition, division, Code stamp, inspection agency and any corporate specifications at quotation, so the vessel matches what the plant’s integrity program expects.

Who inspects pressure vessels at a Texas plant?

During fabrication, the authorized inspector from an authorized inspection agency reviews materials, procedures, examinations and the hydrostatic test before the Code stamp is applied. In service, the owner’s API 510 inspector, or the insurer’s inspector where the policy requires it, sets and performs the inspections, because Texas has no state inspector for unfired pressure vessels.

Who approves pressure vessels before they ship to a Texas site?

The authorized inspector signs the manufacturer’s data report after witnessing the final inspection and pressure test, and the owner’s engineer approves the design calculations and drawings before fabrication. Many Texas owners also send their own source inspector to witness the hydrostatic test and review the documentation package before release for shipment.

Can pressure vessels be welded after years of refinery service?

Yes. Repairs and alterations on vessels in service follow API 510 or the NBIC, depending on the owner’s program. The repair procedure accounts for the material’s condition, hydrogen or sour service history, preheat and postweld heat treatment, and the examination and pressure test required afterward. The owner’s inspector authorizes the repair before work starts and accepts it when it is complete.

Does a Texas air receiver need a state certificate?

Texas does not register or certificate air receivers, because the boiler law excludes pressure vessels. The receiver still needs ASME construction, and OSHA 1910.169 requires a drain at the lowest point, an indicating pressure gauge and a properly set safety valve. Insurers commonly add periodic inspection requirements, which Paul Industries builds into the receiver’s documentation.

Is a steam drum on a waste heat unit a boiler or a vessel in Texas?

The steam collection or liberation drum on a process steam generator is treated as a boiler: it is registered with TDLR, inspected annually and can have its internal interval extended to 120 or 144 months with good water treatment records. The waste heat exchanger itself is exempt as a process vessel and stays in the plant’s mechanical integrity program.

Does the TCEQ storage vessel program reach pressure vessels?

The Aboveground Storage Vessel Safety Program under 30 TAC Chapter 338 covers atmospheric storage vessels of 21,000 gallons or more at refineries, petrochemical plants and bulk terminals. It excludes flow-through process tanks, including pressure and process vessels, and tanks operated above 0.5 psig, so a pressure vessel stays outside it while a large atmospheric tank beside it may fall inside.

Which materials suit wet H2S service on the Texas coast?

Refinery wet H2S service is specified to NACE MR0103, which controls hardness of base metal, welds and heat-affected zones to resist sulfide stress cracking. Owners often add HIC-tested plate and postweld heat treatment for severe service. Paul Industries builds to the owner’s sour service specification and records hardness testing in the turnover package.

How are tall columns on the Texas coast designed for wind?

Tall columns are designed for the site’s code wind speed, which is high along the coast, with checks on shell stress, skirt and base ring, anchor bolts and deflection. Slender columns are also checked for vortex shedding, and strakes or dampers are added where needed. Platforms, ladders and insulation add wind area and are included in the loads.

Which documents does a PSM audit ask for on a new vessel?

Auditors look for the manufacturer’s data report, design calculations, drawings, material test reports, welding procedures and welder qualifications, NDE and heat treatment records, the hydrostatic test record, relief device sizing basis and the baseline thickness survey. Those support the process safety information and mechanical integrity elements of the PSM program, so Paul Industries delivers them in one indexed package.

What sets the delivery date of a large vessel to a Texas site?

Material lead time, design approval and the delivery route usually set the date. Heavy or large-diameter vessels move to coastal plants by barge or under oversize and overweight road permits, and the route can cap diameter, length and weight. Paul Industries plans transport during design, and splits a vessel into sections for site assembly when the route requires it.

How much does a pressure vessel cost for a Texas refinery or chemical plant?

Material, size, wall thickness, nozzles, internals, heat treatment, NDE extent and schedule set the price. Alloy, clad or impact-tested construction costs considerably more than carbon steel of the same size. Paul Industries gives a budget range from comparable vessels once it has the data sheet, then a firm price when the design is approved.

What data sheet details does Paul Industries need to quote a Texas vessel?

Send design pressure and temperature, minimum design metal temperature, fluid and service, capacity or dimensions, nozzle list, corrosion allowance, code edition and division, PWHT and NDE requirements, sour or cryogenic service notes, and the required delivery date. Paul Industries replies with a budget range and the questions that remain before a firm price.

Need a code vessel built or rerated for a Texas plant?

Send the data sheet or process conditions, the code division and your turnaround or startup date. Call 201-450-8280 or request a quote.