Paul Industries provides pressure vessel fabrication in Kentucky, designing and building ASME Section VIII vessels, receivers, reactors, jacketed kettles, separators and heat transfer vessels for chemical, food, distilling, automotive and pharmaceutical plants across the Commonwealth. Kentucky regulates unfired pressure vessels under the same statute as boilers, so a new vessel needs the right code mark, a National Board data report, a state installation inspection and a Kentucky registration tag before it runs. Paul Industries designs, fabricates, supplies, installs, tests and repairs vessels, with the paperwork built for the Kentucky inspector from the first drawing.

Request a quote or call 201-450-8280

Headquarters 256 Shore Drive, Kilmarnock, Virginia
State scope Unfired pressure vessels above 15 psi, unless exempt (KRS 236.060)
Registration Kentucky number on a metal tag near the nameplate (815 KAR 15:025)
Autoclaves and sterilizers Reinspected every four years (815 KAR 15:026)
Jacketed kettles Reinspected every two years (815 KAR 15:026)
Reviewed November 2026

What does Kentucky regulate in pressure vessel fabrication?

Kentucky regulates pressure vessel fabrication in Kentucky through KRS Chapter 236 and 815 KAR Chapter 15, which require new vessels to meet the ASME Boiler and Pressure Vessel Code, carry the applicable ASME certification mark, and pass a state installation inspection before a certificate is issued. The Boiler Inspection Section of the Department of Housing, Buildings and Construction administers the program, with commissioned special inspectors from insurance companies and owner-user inspectors at qualifying plants working under the same rules.

KRS 236.010 defines a pressure vessel broadly as a vessel in which the pressure comes from an external source or from the application of heat, other than a boiler. That definition sweeps in air receivers, reactors, autoclaves, jacketed kettles, deaerators, heat exchanger shells and hot water storage tanks. The national treatment of vessel design and code construction sits on the pressure vessel fabrication page; this page covers the Kentucky rules a vessel meets on its way into service.

What makes a vessel a pressure vessel under Kentucky rules?

A vessel becomes a regulated pressure vessel in Kentucky when it holds internal or external pressure above 15 psi and falls outside the exemptions listed in KRS 236.060. The exemption list is long and specific, and a vessel that sits just over one of its limits is in the program, so the design conditions decide the paperwork as much as the process does.

Kentucky pressure vessel regulations: common exemptions under KRS 236.060
VesselExempt whenIn the Kentucky program when
Any vesselOperating pressure of 15 psi or less, internal or externalAbove 15 psi
Compressed air receiver120 gallons or lessLarger than 120 gallons
Small single wall vesselInside diameter, width, height or diagonal of 6 inches or lessAny dimension above 6 inches, unless otherwise exempt
ASME UM vesselWithin 1.5 cu ft at 600 psi, 3 cu ft at 350 psi, or 5 cu ft at 250 psiBeyond those volume and pressure pairs
Indirect water heaterWithin 200,000 Btu/hr, 210 F and 120 gallonsAny one of those limits exceeded
Machine housingsIntegral parts of pumps, compressors, turbines, engines and hydraulic or pneumatic cylindersSeparate vessels fed by that machinery
LP gas containerUnder the department’s LP gas program, KRS Chapter 234Other gases and liquids
Vessels at oil refineries or under federal controlExempt from KRS 236.005 to 236.150Chemical and manufacturing plants outside refineries

Two items on that list catch plants out. A compressed air receiver of 120 gallons is exempt while a 200 gallon receiver is a registered vessel with its own inspection record, and a steam-heated hot water storage tank stays exempt only while it remains within all three of its heat input, temperature and capacity limits.

Kentucky pressure vessel regulations for a new vessel

A new pressure vessel in Kentucky is built to the ASME Boiler and Pressure Vessel Code, marked with the applicable ASME certification mark, and supported by a manufacturer’s data report filed with the National Board, with the National Board registration number on the data plate, under 815 KAR 15:025. A vessel bearing the UM mark may be registered with the National Board but is not required to be. Installation follows NBIC Part 1, and the department inspects new installations and their connected pressure piping for compliance.

At installation or first inspection the vessel receives a Commonwealth of Kentucky registration number on a metal tag fixed near the manufacturer’s nameplate or data plate. Inspectors who find an unregistered vessel notify the department within 30 days, so a receiver bought used or moved from another site without a tag tends to surface at the next insurance or state visit.

The Kentucky pressure vessel permit

The Kentucky pressure vessel permit is issued under KRS 236.240 before a vessel is installed or erected, or repaired in a way that affects its strength, with permits going only to those holding the contractor license KRS 236.210 establishes for boiler and pressure vessel work. The permit fee includes an interim and a final inspection, and the installation is inspected before welded or mechanical joints on the connected pressure piping are covered.

From data sheet to Kentucky registration tag
StepWhat happensKentucky record
1. Design basisDesign pressure and temperature, MDMT, corrosion allowance, cyclic service and relief scenarios fixed with the ownerData sheet and design calculations
2. Code constructionFabrication under ASME Section VIII with an Authorized Inspector, Section IX procedures and qualified weldersMaterial test reports, weld maps, NDE reports
3. Pressure test and markingCode hydrostatic or pneumatic test, ASME certification mark appliedManufacturer’s data report, National Board number on the plate
4. PermitInstallation permit under KRS 236.240 before setting the vesselPermit with interim and final inspections
5. InstallationSetting, anchoring, relief devices and piping to NBIC Part 1 and the B31 codesPiping inspected before insulation
6. State inspectionDepartment installation inspection, Kentucky number assignedMetal registration tag near the nameplate, certificate of inspection

Kentucky state specials for vessels outside the ASME Code

A vessel of special design that is equivalent to, but ineligible for, the ASME certification mark can be approved in Kentucky as a state special under 815 KAR 15:025. The owner, user or authorized agent applies in writing to the commissioner before installation, with shop drawings and weld details, design calculations, material specifications, Section IX weld procedures and welder qualifications, and the shop inspection agency and its authorized inspector identified. Drawings and calculations are signed by a professional engineer with a boiler and pressure vessel background.

When a design exceeds ASME Code limits, equivalency is shown through API 579-1/ASME FFS-1. The finished vessel carries an equivalent data report signed by the manufacturer and the authorized inspector, written on the state’s equivalent form rather than the ASME data report forms, and a boiler inspector examines it on arrival in Kentucky before installation. Imported equipment and vessels built to foreign codes are the usual candidates, and Paul Industries prepares the application package and the equivalency calculations alongside the build.

Why are pressure vessels cylindrical, and what are pressure vessels made of?

Pressure vessels are cylindrical with dished or hemispherical heads because a curved shell carries internal pressure as membrane stress, while flat walls bend and need far greater thickness or heavy stiffening for the same pressure. Hoop stress in a cylinder is twice the longitudinal stress, which is why shell thickness is set by the circumferential direction and why hemispherical heads can be roughly half the shell thickness.

Kentucky vessels are made mostly of carbon steel plate such as SA-516 Grade 70 for air, steam, water and many chemical services, and austenitic stainless steels such as SA-240 Type 304L and 316L for food, distilling, pharmaceutical and corrosive services, with duplex stainless, nickel alloys and clad plate where chlorides or acids demand them. Kentucky produces flat stainless at North American Stainless in Ghent, Carroll County, which expanded its cold rolling capacity in 2025, though vessel plate is specified to ASME Section II whatever its mill of origin.

What industries use pressure vessels in Kentucky?

The industries that use pressure vessels in Kentucky include chemicals and plastics, distilling and food processing, automotive and battery manufacturing, pharmaceuticals, power generation and institutional steam. Each brings its own design conditions and inspection pattern.

Calvert City in Marshall County hosts a chemical complex that includes Arkema’s plant, where a retrofit completed in 2025 makes the blowing agent Forane 1233zd and a separate project expands PVDF capacity. Chemical service of that kind calls for reactors, separators, receivers and relief-protected storage vessels with careful material selection. Louisville’s Rubbertown district carries similar demand. In Lexington, Piramal Pharma Solutions is expanding its sterile fill and finish site with two large lyophilizers, equipment whose chambers and condensers are pressure vessels in their own right. Ford’s Glendale plant in Hardin County is retooling to make battery energy storage systems, and automotive plants in Georgetown and Louisville run large compressed air receivers. Related Kentucky work appears on tank fabrication in Kentucky and process piping in Kentucky.

Kentucky vessel types, design focus and inspection interval
VesselWhere in KentuckyDesign focusReinspection under 815 KAR 15:026
Reactors and separators above 200 psiCalvert City, Louisville chemical plantsMaterial, corrosion allowance, relief sizingEvery five years in the current text
Autoclaves and sterilizersPharmaceutical, device and hospital sitesQuick-opening closures, cyclic serviceEvery four years
Hot water storage tanksCampuses, hospitals, food plantsLining, temperature limitsEvery four years
Jacketed kettlesFood and sauce plants, steam-jacketed cookersJacket pressure, sanitary inner shellEvery two years
DeaeratorsBoiler houses statewideWeld cracking in feedwater serviceInternal and external every ten years
Compressed air receivers over 120 gallonsAutomotive, appliance and metals plantsDrainage, corrosion at the bottom headBy the general vessel schedule

How often do pressure vessels need to be inspected in Kentucky?

Kentucky pressure vessels are inspected at installation under KRS 236.110, then on the reinspection schedule in 815 KAR 15:026: in its current text, every five years for vessels above 200 psi MAWP, every four years for hot water storage tanks, sterilizers and autoclaves, every two years for jacketed kettles and pressure vessels for human occupancy, and every ten years internally and externally for deaerators. Every vessel is reinspected when it is repaired, altered or relocated.

A 2026 amendment to 815 KAR 15:026 in the regulatory process would change several of those figures, including four years for vessels above 200 psi, ten years for vessels at 200 psi or less, three years for liquid carbon dioxide vessels and six years for deaerators, and would tie inspections to the 2025 edition of NBIC Part 2. Paul Industries checks the schedule in force when a vessel is designed and when it is installed, and builds inspection openings to suit.

How often do pressure vessels need to be tested?

Pressure vessels need a code pressure test when they are built and after repairs or alterations that the inspector requires to be tested, and in-service inspections in Kentucky are visual and nondestructive unless the inspector calls for more. When an existing vessel is hydrostatically tested, 815 KAR 15:026 sets the test water at least 30 degrees Fahrenheit above the minimum design metal temperature and keeps the metal at or below 120 degrees, with strength tests following the original code and never exceeding one and one half times the MAWP.

Installation details the Kentucky inspector looks for

Kentucky installation rules reach beyond the vessel itself. Under 815 KAR 15:025, new and replacement vessels need at least two feet of clearance on all service sides and five feet between a manhole opening and any wall, ceiling or piping that would block entry. A vertical vessel subject to corrosion with a dished bottom head has that head concave to pressure so it drains, and the data plate stays accessible and free of insulation that cannot readily be removed.

Relief protection carries Kentucky specifics too. Where a vessel can be exposed to fire or other unexpected external heat, supplemental relieving devices limit the pressure rise to 21 percent above the MAWP. Omitting a relief device is allowed only under the ASME Section VIII provisions the regulation names, and except under Division 1 Appendix M the Boiler Inspection Section is notified with the supporting calculations before the vessel enters service. Paul Industries designs supports, platforms, nozzles and insulation around those requirements.

ASME pressure vessel standards behind a Kentucky build

The ASME pressure vessel standards behind a Kentucky build are Section VIII Division 1 for most process and utility vessels, Division 2 where alternative design rules save material on large or high pressure vessels, and Division 3 for very high pressure equipment, with Section II for materials, Section V for examination methods and Section IX for welding qualifications. Kentucky’s rules name those sections through KRS 236.040 and 815 KAR 15:025, and pressure vessels for human occupancy follow ASME PVHO-1.

Division 1 suits most Kentucky receivers, kettles, separators and filter housings. Division 2 earns its added design and examination effort on thick-walled reactors and large storage spheres, where its higher allowable stresses reduce plate thickness and weight enough to pay for the extra analysis. Cyclic service, such as autoclaves that pressurize and vent many times a day, calls for a fatigue screening whichever division is used. Paul Industries sets the division, joint efficiencies and radiography level with the owner at the data sheet stage, because changing them after plate is ordered costs time.

Jacketed, lined and sanitary vessels for Kentucky food and spirits

Jacketed and sanitary vessels for Kentucky food and spirits plants combine two sets of rules: the jacket and any pressurized shell follow ASME Section VIII and the Kentucky inspection program, while product contact surfaces follow sanitary design practice such as 3-A standards for dairy and food, or ASME BPE where the owner specifies it. Dimple jackets, half-pipe coils and conventional jackets each suit different heating and cooling duties, and the choice changes both the thermal performance and how the jacket is inspected later.

Food plants that cook sauces, fillings and syrups rely on steam-jacketed kettles, which Kentucky reinspects every two years, so Paul Industries places jacket inspection openings, drains and nameplates where an inspector can reach them without stripping insulation. Spirits plants use jacketed receivers and heated vessels where ethanol vapors make venting and relief discharge location part of the safety design, and 815 KAR 15:025 requires relief discharges to be located to prevent injury to persons and property. Lined carbon steel suits some brine and chemical services, while stainless or nickel alloy suits chlorides and acids.

Delivering and setting vessels at operating Kentucky plants

Delivering a vessel to an operating Kentucky plant starts with the route: road clearances, crane access, floor loading and the opening the vessel will pass through. Large reactors and receivers are often shipped with nozzles and supports complete and set in a single lift, while vessels bound for existing buildings may be built in sections or set before a roof or wall is closed. Paul Industries plans rigging, foundation anchor bolts and piping tie-ins together, so the setting crew, the inspector and the piping work arrive in a sequence that keeps the plant running.

Repairs, alterations and rerates on Kentucky vessels

Repairs and alterations to Kentucky pressure vessels conform to NBIC Part 3 under 815 KAR 15:026, and every vessel is reinspected at the time of repair, alteration or relocation. Welded repairs follow the National Board R program, with the inspector reviewing the method before the first arc is struck, and a rerate to new pressure or temperature conditions is an alteration supported by calculations to the original code of construction. At plants with an owner-user inspection program, the owner-user inspector may inspect repairs and alterations to vessels the company owns or operates.

Paul Industries rerates vessels for new process conditions, replaces nozzles and heads, adds jackets and internals, repairs corrosion and cracking, and moves vessels between buildings with the reinstallation inspection the move requires. Welding detail for that work appears on industrial welding services in Kentucky.

The vessel file a Kentucky owner keeps

The vessel file a Kentucky owner keeps is what lets every later inspection, rerate and insurance renewal proceed without guesswork. Paul Industries hands over the manufacturer’s data report and partial data reports for subassemblies, the general arrangement and nozzle drawings, design calculations, material test reports traced to the weld map, weld procedure and welder qualification records, radiography and other examination reports, the pressure test record, relief device data sheets and sizing basis, the installation permit and its final inspection, and a photograph of the nameplate beside the Kentucky registration tag. Electronic and paper sets follow the owner’s document numbering, so the file drops into the plant’s mechanical integrity program the day the vessel starts up.

That file also shortens future work. When a corrosion survey shows thinning, the original calculations and material records let a fitness-for-service assessment or rerate proceed from known data rather than from field measurements alone.

What does pressure vessel fabrication in Kentucky cost?

The cost of pressure vessel fabrication in Kentucky is driven by material and thickness, diameter and length, design pressure and temperature, nozzle count and size, internals and jackets, the level of radiography and other examination the code or the owner specifies, surface finish for sanitary service, and transport to the site. Kentucky adds permit and inspection fees that scale with the installation’s dollar value under 815 KAR 15:027, a small share of the total.

Stainless and alloy vessels cost several times their carbon steel equivalents in material, and polished sanitary interiors add finishing time. Paul Industries gives a budget range from comparable vessels once the data sheet is drafted, and a firm price once the design conditions, materials and nozzle schedule are fixed.

Who fabricates pressure vessels for Kentucky plants?

Paul Industries fabricates pressure vessels for Kentucky plants: carbon steel and stainless receivers, reactors, separators, filter housings, jacketed vessels, autoclave shells and heat exchanger shells, with design, supply, delivery, setting and piping included as the owner requires. Buyers choose supply-only, design-build or complete installation. Paul Industries is headquartered at 256 Shore Drive, Kilmarnock, Virginia, was formerly based in northern New Jersey, then Pennsylvania, and as an East Coast contractor takes work across Kentucky and in all 50 states.

The same approach runs at home under pressure vessel fabrication in Virginia, the headquarters state, and in neighboring states, including pressure vessel fabrication in Tennessee. Vessels for steam plants often pair with boiler repair in Kentucky, and regulated process vessels with validation and commissioning in Kentucky. Regional coverage is on the Southeast page and the Kentucky hub.

Code vessels from Paul Industries for Kentucky owners

Paul Industries designs, builds, tests, delivers, sets, pipes and repairs ASME pressure vessels for Kentucky plants, with the data report, National Board number, permit, installation inspection and Kentucky registration tag carried through as one scope. Send the data sheet or process conditions and request a quote.

Standards referenced: KRS Chapter 236 · 815 KAR 15:025 and 15:026 · ASME Boiler and Pressure Vessel Code Section VIII, Divisions 1, 2 and 3 · ASME Section IX · ASME Section II materials · ASME PVHO-1 · National Board Inspection Code Parts 1, 2 and 3 · API 579-1/ASME FFS-1

Frequently asked questions

Who builds reactors and receivers for chemical plants in Calvert City and Paducah?

Paul Industries builds reactors, receivers, separators and relief-protected vessels for chemical plants in Calvert City, Paducah and the rest of western Kentucky. Chemical service there involves fluorochemicals and specialty polymers, so material selection, corrosion allowance and relief sizing get as much attention as thickness. Each vessel arrives with its data report, National Board number and documents ready for the Kentucky installation inspection.

Does Paul Industries fabricate vessels for Louisville plants and the Rubbertown district?

Yes. Paul Industries fabricates and installs pressure vessels for Louisville manufacturers, food plants, hospitals and the Rubbertown chemical district in western Jefferson County. Typical work includes air and nitrogen receivers, process reactors, filter housings and hot water storage tanks, along with rerates and repairs on vessels already in service.

Who supplies jacketed kettles and process vessels to food plants and distilleries around Bardstown and Lexington?

Paul Industries supplies jacketed kettles, cookers, receivers and stainless process vessels to food plants and distilleries around Bardstown, Nelson County, Lexington and Frankfort. Kentucky reinspects jacketed kettles every two years under 815 KAR 15:026, so jacket inspection openings and accessible nameplates are designed in from the start.

Is the Kentucky boiler and pressure vessel code the same as the ASME Code?

The Kentucky boiler and pressure vessel code is KRS Chapter 236 with 815 KAR Chapter 15, and it adopts the ASME Boiler and Pressure Vessel Code for construction rather than replacing it. Kentucky adds the permit, installation inspection, registration tag, reinspection intervals and state special route. A vessel therefore meets ASME Section VIII and the Kentucky rules together.

Where are the Kentucky boiler and pressure vessel rules published?

The Kentucky boiler and pressure vessel rules are published as KRS Chapter 236 by the Kentucky General Assembly and as 815 KAR Chapter 15 in the Kentucky Administrative Regulations, both on the Legislative Research Commission website. New installations fall under 815 KAR 15:025, existing vessels under 15:026 and fees under 15:027, with amendments filed in 2026.

Does a 200 gallon air receiver need a Kentucky certificate?

A 200 gallon compressed air receiver is above the 120 gallon exemption in KRS 236.060, so it is a regulated pressure vessel that needs an installation inspection, a Kentucky registration tag and periodic reinspection. Receivers of 120 gallons or less are exempt. Paul Industries supplies ASME receivers with drains, relief valves and inspection openings sized for the plant’s air system.

What does the Kentucky registration tag on a vessel show?

The tag carries the Commonwealth of Kentucky registration number assigned at installation or first inspection under 815 KAR 15:025, and it is fixed near the manufacturer’s nameplate or data plate. The number ties the vessel to its state inspection history, which matters when the vessel changes insurer, owner or location. Inspectors report unregistered vessels to the department within 30 days.

Can a vessel built to a foreign code be installed in Kentucky?

A vessel that is equivalent to, but ineligible for, the ASME certification mark can be approved as a Kentucky state special under 815 KAR 15:025. The application goes to the commissioner before installation with drawings, calculations signed by a professional engineer, materials, weld procedures and the shop inspection agency, and the vessel is inspected on arrival. Paul Industries prepares the package and the equivalency calculations.

How is an autoclave or sterilizer treated under Kentucky rules?

An autoclave or sterilizer is a pressure vessel under KRS Chapter 236, inspected at installation and reinspected every four years under 815 KAR 15:026. Quick-opening closures and cyclic service make the door, locking mechanism and interlocks the focus of each inspection. Paul Industries supplies, installs and repairs autoclave shells and jackets, with the records a quality unit needs for qualification.

Can a plant's own inspectors inspect pressure vessel repairs in Kentucky?

Plants with owner-user inspectors may have those inspectors inspect repairs and alterations to pressure vessels the company owns or operates, under 815 KAR 15:026, and report on the National Board form to the Boiler Inspection Section. When the owner-user inspector and the company disagree about a condition, the department makes the final determination.

What clearance does Kentucky require around a new pressure vessel?

815 KAR 15:025 requires at least two feet of clearance on all service sides of a new or replacement vessel and five feet between a manhole opening and any wall, ceiling or piping that would prevent entry. A vessel subject to external corrosion also needs access to its whole exterior or a connection that lets it be removed for inspection. Paul Industries lays out vessel rooms to those limits.

How is a used pressure vessel moved into a Kentucky plant?

A used vessel is inspected by a boiler inspector before it goes into service, under 815 KAR 15:026, and that examination can extend to internal and external visual checks, a hydrostatic test or other NDE. Relocated vessels are reinspected at the time of relocation, and fittings and appliances meet the referenced ASME edition. Paul Industries surveys, repairs and reinstalls the vessel with that inspection.

Does a rerate change a Kentucky vessel's registration?

A rerate is an alteration under NBIC Part 3, made with calculations to the original code of construction, an inspector’s acceptance and a pressure test where required, and the vessel is reinspected at the time of alteration under 815 KAR 15:026. The registration number stays with the vessel while the nameplate data and records change. Paul Industries prepares the calculations, alteration report and new nameplate.

Which vessels for a pharmaceutical site in Lexington need more than Section VIII?

Pharmaceutical vessels in Lexington and elsewhere in Kentucky are built to ASME Section VIII and usually to ASME BPE for product contact surfaces, with surface finish, drainability and documentation that support qualification. Lyophilizer chambers, autoclaves and clean steam vessels also carry the state inspection schedule. Paul Industries builds them with the turnover package a quality unit reviews.

How long does a custom ASME vessel take for a Kentucky project?

A custom ASME vessel takes longer when its plate, forgings or alloy material carry long mill lead times, and shorter when standard carbon steel plate and stock nozzles suit the design. Drawing approval by the owner, examination requirements and the Kentucky permit and inspection steps also set the date. Paul Industries gives a schedule with the quote and orders long-lead material as soon as the design is fixed.

Which delivery routes does Paul Industries offer Kentucky vessel buyers?

Kentucky buyers choose supply-only delivery of a code vessel with its data report, design-build where Paul Industries develops the design from process conditions, or complete installation with setting, piping, relief devices, permit and state inspection. Many plants combine routes, for example supply-only for spare receivers and complete installation for a reactor replacement.

What should a Kentucky plant send for a pressure vessel quote?

Send the process fluid, design pressure and temperature, minimum design metal temperature, volume or dimensions, material preference, nozzle list, internals or jacket requirements, and any owner specifications for examination or finish. For a rerate or repair, add the existing data report, Kentucky registration number and latest inspection report. Paul Industries then prices the vessel and its installation.

Specifying a code vessel for a Kentucky plant?

Send the data sheet or process conditions, the nozzle list and any existing vessel records. Call 201-450-8280 or request a quote.