Paul Industries designs, builds and services ultrapure water systems in Indiana: pretreatment for the state’s very hard feedwater, reverse osmosis, electrodeionization, polishing and distribution loops for semiconductor, research, power and pharmaceutical sites. Indiana’s water is very hard by any measure, and its new semiconductor investment in West Lafayette is raising the bar on purity. Paul Industries builds the system from the feedwater analysis to the last point of use, as supply-only equipment, design-build or complete installation.
Request a quote or call 201-450-8280
What do ultrapure water systems in Indiana supply, and to whom?
Ultrapure water systems in Indiana supply water purified close to its theoretical limit, around 18.2 megohm-centimeters resistivity at 25 degrees Celsius with very low organic carbon, particles, silica and dissolved gases, to processes that cannot tolerate dissolved impurities. In Indiana the users are semiconductor packaging and research cleanrooms, university and corporate laboratories, high-pressure boilers at power and industrial plants, and pharmaceutical and biotech sites whose laboratories and some processes need water purer than the compendial grades.
The treatment train and specifications are explained on the national ultrapure water systems page, and the device-industry rinse water systems that Indiana’s orthopedic manufacturers use are covered on high-purity water systems in Indiana. This page covers what Indiana changes for ultrapure plants: the feedwater, the water rights and discharge rules, the cold winters, and the industries now asking for this water.
Semiconductor manufacturing in Indiana and its water
Semiconductor manufacturing in Indiana took a large step in August 2026, when SK hynix broke ground in Purdue Research Park in West Lafayette on a $4 billion advanced packaging production and research facility for high-bandwidth memory, with cleanroom operation targeted for 2028. Advanced packaging stacks and bonds memory dies, and its wafer cleaning, rinsing, dicing and plating steps use ultrapure water continuously.
The plant is under construction, and it is a market fact about Indiana, not a Paul Industries project. It joins research cleanrooms that already depend on ultrapure water, such as Purdue’s Birck Nanotechnology Center, whose 25,000 square foot nanofabrication cleanroom runs bays from ISO class 3 to 6. Semiconductor ultrapure water is usually specified against SEMI F63 or the owner’s own tighter limits, with online monitoring of resistivity, total organic carbon, particles, dissolved oxygen and silica at the point of use. Suppliers and research groups that locate around a new packaging plant bring smaller systems with the same specifications.
For Indiana, the significance is that semiconductor-grade water is arriving in a state whose industrial water systems have mostly served pharmaceutical, device, food and power plants. The design culture differs: semiconductor loops are built from high-purity plastics, run continuously at constant velocity, and are judged by trace contaminants measured in parts per billion and below. Paul Industries builds both kinds of systems and keeps their standards separate.
Why is Indiana feedwater so demanding for ultrapure plants?
Indiana feedwater is demanding because most of it is very hard: limestone and dolomite aquifers underlie about half the state, and the water that passes through them dissolves calcium and magnesium. the Indianapolis water utility gives a usual hardness range of 200 to 350 milligrams per liter, counted as calcium carbonate, and a USGS survey found median groundwater hardness of roughly 286 to 340 milligrams per liter across Indiana’s aquifer units.
Hardness sets the limit on reverse osmosis recovery. As RO concentrates the feed, calcium carbonate and calcium sulfate approach saturation in the reject stream and scale the last membranes in the array. Hard feed therefore needs softening, antiscalant dosing, pH control or a combination, and even then the recovery an Indiana RO can reach is lower than the same unit would reach on soft water. Groundwater sources often add iron and manganese, which foul membranes and resin unless they are removed first, and surface supplies vary with season and storm runoff.
| Source | Typical character | Pretreatment emphasis |
|---|---|---|
| Indianapolis municipal supply | Very hard; blend of river, reservoir and groundwater plants that varies by service area | Softening or antiscalant, carbon or bisulfite for disinfectant removal, monitoring for blend changes |
| Private wells in carbonate aquifers | Very hard, often with iron and manganese | Iron and manganese removal, softening, careful RO recovery limits |
| River supplies such as the Wabash, White and Ohio | Seasonal turbidity, organics and temperature swings | Clarification or ultrafiltration, organics removal, feed heating in winter |
| Lake Michigan supplies in Northwest Indiana | Steadier chemistry than rivers; cold water much of the year | Filtration, disinfectant removal, feed heating for RO flux |
Paul Industries starts every Indiana ultrapure project with a full feedwater analysis taken over more than one season where the source varies, then designs pretreatment for the worst case. A plant designed on one summer sample of a blended municipal supply can lose capacity when the utility shifts sources.
Designing the treatment train around Indiana feed
An Indiana ultrapure treatment train is designed backwards from the purity required and forwards from the feedwater, and on hard Indiana supplies the front end takes a larger share of the cost than in soft-water states. A typical sequence is multimedia or ultrafiltration, softening or antiscalant, disinfectant removal, double-pass reverse osmosis, electrodeionization, degasification, and a polishing loop with ultraviolet oxidation, mixed-bed or polishing resin, ultrafiltration and final filters.
Softening ahead of RO is common in Indiana because it lets the RO run at higher recovery without scaling, but it brings salt use and brine discharge. Antiscalant alone saves the softener but caps recovery lower. Some large plants use both, or remove hardness with lime treatment or nanofiltration. Silica deserves its own check, because semiconductor and high-pressure boiler users set tight silica limits and Indiana groundwater can carry enough to limit RO recovery on its own. Paul Industries runs projections for each option against the measured feed and presents the recovery, chemical use, brine volume and operating cost side by side, so the owner chooses with numbers.
Downstream of RO the train converges on the familiar pattern: EDI to reach high resistivity without regenerant chemicals, a membrane degasifier for dissolved oxygen and carbon dioxide where the specification calls for it, and a polishing loop that keeps water moving through UV, polishing resin and final filtration back to storage. Piping for the loop is PVDF or other high-purity plastic for semiconductor use, or electropolished stainless where hot sanitization is needed, built and tested as described on process piping in Indiana.
Which ultrapure water grade does an Indiana user need?
The ultrapure water grade an Indiana user needs depends on what the water touches. A semiconductor packaging line, a high-pressure boiler, a research laboratory and a pharmaceutical quality control laboratory all ask for very pure water, but they measure purity differently and set limits on different contaminants, and building to the wrong standard costs either purity or money.
| User | Common reference | Parameters that drive the design | Typical system features |
|---|---|---|---|
| Semiconductor packaging and research cleanrooms | SEMI F63 or owner specification | Resistivity, TOC, particles, dissolved oxygen, silica, metals at trace levels | Double-pass RO, EDI, degasification, UV, polishing resin, ultrafiltration, PVDF loop |
| High-pressure boiler and HRSG makeup | Boiler and turbine makers’ limits | Silica, sodium, conductivity at high flow | RO, EDI or mixed beds, condensate polishing tie-in |
| University and corporate laboratories | ASTM D1193 Type I or equivalent | Resistivity, TOC, bacteria at many small points of use | Central loop or point-of-use polishers fed by a building RO |
| Pharmaceutical QC laboratories | Owner specification beside USP Purified Water | Resistivity, TOC, bacteria and endotoxin for some assays | Polishers fed from the Purified Water loop or a separate system |
| Liquid-cooled data center fill | CDU and rack makers’ fluid specifications | Conductivity, chloride, hardness, bacteria | RO or deionization with storage and a dosing point for inhibitor |
Paul Industries writes the specification with the owner before the design starts, listing each parameter, its limit, where it is measured and how often. That list becomes the acceptance test at startup and the monitoring plan afterward, so the system is built, tested and run against the same numbers.
Cold Indiana feedwater and RO capacity
Cold Indiana feedwater reduces reverse osmosis capacity in winter, because membrane permeability drops as water cools, roughly 2.5 to 3 percent of flux for each degree Celsius by the usual rule of thumb. River and lake supplies in Indiana follow the seasons, running cold through the winter and much warmer by late summer, so an RO sized at a summer feed temperature can fall well short of demand in winter.
Two answers are common. The RO can be sized for the coldest feed and run at reduced pressure or with fewer elements in summer, or the feed can be warmed through a plate heat exchanger to a steady temperature year round. Warming is often cheap in Indiana plants that have waste heat from compressors, chillers or process cooling, and it holds RO performance steady, which helps EDI and the polishing loop downstream. Paul Industries designs the heat exchanger, the temperature control and the high-temperature limit that protects the membranes, and uses the plant’s cooling water where it can supply the heat.
Keeping an Indiana ultrapure loop clean of bacteria
An ultrapure loop in Indiana stays free of bacteria the same way it does anywhere: continuous flow at velocities that discourage biofilm, no dead legs, UV treatment in the loop, and periodic sanitization with hot water, ozone or chemicals as the materials allow. Indiana adds one factor: summer heat in plant rooms and long pipe runs warms stagnant water, and warm, low-nutrient water is where biofilm starts.
Paul Industries designs loops with return velocities set for the material and flow, short connections at every point of use, and sample valves at the loop return and critical drops. Storage tanks get spray balls and vent filters, and a nitrogen blanket where dissolved oxygen or carbon dioxide pickup matters. Sanitization frequency is set from bacteria counts during the first months, not guessed, and the same counts tell when membranes or resin need attention.
Adding points of use to a running Indiana loop
Adding points of use to a running Indiana ultrapure loop is planned so that the loop never stops circulating and the new branch never becomes a dead leg. New drops are prefabricated, cleaned and capped off site, then installed during a short isolation of one section, with the rest of the loop kept moving through a bypass where the layout allows.
After tie-in, the new section is flushed to drain until resistivity, TOC and particle readings return to the loop’s baseline, and bacteria samples are taken before the tool or instrument is connected. In a growing research park, where new laboratories and tool bays arrive every year, Paul Industries leaves valved, capped connections on the main loop at the locations the master plan shows, so later drops connect without cutting the header.
Startup, acceptance and qualification
Startup of an Indiana ultrapure water system runs from pretreatment forward, each stage proven before the next is placed in service, and ends with an acceptance test against the agreed specification at the points of use. A new PVDF or stainless loop needs a rinse-up period before it reaches full resistivity and low TOC, and the schedule allows for it.
For pharmaceutical and regulated laboratory systems, installation and operational qualification follow, with documented test results, calibrated instruments and the drawings and material records that support them. Semiconductor and research systems are accepted on the monitored purity at the point of use over an agreed run period. Paul Industries provides the startup records, analyzer calibrations, test results and operating procedures with the system, and trains the owner’s operators on the controls and the alarms.
Water rights, reject and discharge in Indiana
Water rights and discharge rules reach large Indiana ultrapure plants at both ends: a site that can withdraw more than 100,000 gallons a day from all its sources must register with the DNR as a significant water withdrawal facility and report its use each year, and the RO reject, softener brine, EDI concentrate and regeneration waste the plant sends to drain need an approved discharge path through IDEM or the receiving treatment plant.
Hard feedwater makes both ends larger. An RO that can recover only part of its feed on Indiana water sends the rest to drain, and softener regeneration adds a salty brine stream. Paul Industries reduces both where the economics work: a second-stage RO on the first stage’s reject, reject reuse for cooling tower makeup or other non-critical uses where its chemistry allows, and regeneration sized to actual hardness instead of a fixed timer. Meters on feed, permeate, reject and brine produce the volumes the DNR report and the discharge permit need. Semiconductor sites in particular should expect reclaim of rinse water to be part of the design, since it lowers both withdrawal and discharge.
Membrane cleaning on hard Indiana feed
Membrane cleaning comes around more often on Indiana feedwater than on soft supplies, because hardness that slips past pretreatment, iron from wells and organics from rivers all foul reverse osmosis elements over time. Cleaning is triggered by normalized data rather than the calendar: membrane makers’ guidance commonly calls for a clean when normalized permeate flow falls by about 10 to 15 percent or normalized pressure drop rises by about 15 percent from the clean baseline.
Scale from calcium carbonate responds to low-pH cleaning, while organic and biological fouling needs high-pH cleaning, and many Indiana plants need both in sequence. Paul Industries builds RO skids with a dedicated clean-in-place tank, heater, pump and cartridge filter, and with valving that lets each stage be cleaned separately. The normalization software that tracks flow, pressure and salt passage against temperature, important in a state where feed temperature swings widely between seasons, is set up at startup so the first baseline is recorded while the membranes are new. When cleanings come closer together, the trend usually points back to pretreatment, and that is where Paul Industries looks first.
Pressure vessels and Indiana’s rules for water treatment equipment
Most water treatment vessels in an Indiana ultrapure plant sit outside 675 IAC 30, the state’s boiler and pressure vessel rules, since the article names water softeners as excluded and also leaves out unfired vessels that run completely filled with water no hotter than 180 degrees Fahrenheit. The exceptions are vessels with an air or gas space under pressure, such as compressed air receivers for valve actuators, and any vessel run above the size, relief or temperature limits.
| Vessel | Relevant exclusion | Usual status |
|---|---|---|
| Water softeners | Listed by name in 675 IAC 30-1-2(f) | Outside the article |
| Multimedia, carbon and resin vessels running liquid-full | Full of water at 180 F or less | Outside the article |
| RO and filter housings | Liquid-full at 180 F or less; most also under 15 cubic feet | Outside the article |
| Hot-water sanitized vessels and heat exchangers | Depends on whether sanitization runs above 180 F | Checked case by case |
| Compressed air receivers for actuators | Air space under pressure; volume and relief limits apply | Regulated when above 15 cubic feet or 300 psig relief |
| Nitrogen-blanketed storage tanks | Usually atmospheric or near-atmospheric | Outside the article when relieved at 15 psig or less |
Paul Industries lists each vessel’s contents, operating temperature, volume and relief setting in the turnover records, so the owner can show at a glance which vessels the state inspects. Pharmaceutical sites whose loops are steam-sterilized or sanitized above 180 degrees Fahrenheit get the closest look.
Ultrapure water at Indiana power, research and pharmaceutical sites
Outside semiconductor work, Indiana’s ultrapure water users fall into three groups. Power plants and industrial facilities with high-pressure boilers or heat recovery steam generators need demineralized makeup close to ultrapure quality, because silica and sodium carry into the steam and deposit on turbine blades. Universities and corporate research laboratories across the state use central type 1 water loops or point-of-use polishers for analytical chemistry, cell culture and materials research. Pharmaceutical and biotech sites in Central Indiana use ultrapure water in quality control laboratories and some processes, alongside the Purified Water and Water for Injection systems their compendial processes require.
Each group has its own design priorities. Boiler makeup plants are judged on silica, sodium and conductivity at high flow, and often use mixed-bed polishers after RO and EDI; their chemistry ties into boiler repair in Indiana work on the steam side. Laboratory loops are judged on resistivity, organics and bacteria at many small points of use. Pharmaceutical systems add qualification and change control, covered on validation and commissioning in Indiana. Data centers with liquid-cooled racks need a smaller but steady supply of high-purity fill water for their loops, as described on data center liquid cooling in Indiana.
Budgeting an Indiana ultrapure plant
An ultrapure water system price in Indiana is driven by the required purity, the flow and peak demand, the feedwater chemistry, the redundancy, the loop length and number of points of use, the piping material, the monitoring package and the validation or qualification required. On Indiana feedwater, pretreatment and reject handling take a larger share than they would on soft water.
A laboratory polishing loop in an existing building and a semiconductor plant producing hundreds of gallons per minute differ in cost by orders of magnitude, so a single figure would mislead. Paul Industries gives a budget range from comparable systems once the purity, flow and feedwater analysis are known, and a firm price when the design is set. Operating cost is estimated at the same time: power, chemicals, salt, resin and membrane replacement, and water and sewer charges on reject.
Who installs and maintains ultrapure water systems in Indiana?
Paul Industries installs and maintains ultrapure water systems in Indiana, from feedwater analysis and design through fabrication, installation, startup, qualification and service. Paul Industries is headquartered at 256 Shore Drive, Kilmarnock, Virginia, and takes Indiana work in West Lafayette and Lafayette, Indianapolis and Central Indiana, Lebanon and Boone County, Bloomington, Fort Wayne, South Bend, Northwest Indiana, Kokomo, Columbus and Evansville, as part of a practice covering all 50 states.
After startup, Paul Industries services membranes, EDI stacks, UV lamps, resin and filters, calibrates analyzers, and sanitizes loops on the schedule the specification sets. The headquarters-state version of this page is ultrapure water systems in Virginia, and a comparison with a Southern research market is on ultrapure water systems in North Carolina. Cleanroom construction for the same sites is on cleanrooms in Indiana.
Ultrapure water from Paul Industries across Indiana
Paul Industries delivers ultrapure water systems in Indiana as supply-only equipment, design-build packages or complete installations: pretreatment built for hard Indiana water, reverse osmosis, EDI, polishing loops, distribution, monitoring, reject reduction and service. See Indiana for the state overview and the Midwest for regional work. Send the purity specification, flow and points of use, a feedwater analysis and drawings, then call 201-450-8280 or request a quote.
Standards referenced: SEMI F63 · ASTM D1193 · ASTM D5127 · USP Purified Water and Water for Injection monographs · IC 14-25-7-15 significant water withdrawal facility registration · Indiana Boiler and Pressure Vessel Rules, 675 IAC 30 · Indiana Plumbing Code, 675 IAC 16-1.4
Frequently asked questions
Who builds ultrapure water systems in West Lafayette and Lafayette?
Paul Industries designs, builds and services ultrapure water systems in West Lafayette, Lafayette and Tippecanoe County, for research cleanrooms, laboratories and the suppliers locating around new semiconductor investment there. Feedwater analysis over more than one season comes first, because the supplies there are hard.
Does Paul Industries install ultrapure water systems in Indianapolis and Central Indiana?
Yes. Paul Industries installs and maintains ultrapure systems across Indianapolis, Lebanon, Boone County and the surrounding counties, for pharmaceutical quality control laboratories, research buildings, power and industrial boilers and data center fill water.
Can Paul Industries build ultrapure water plants in Northwest Indiana and South Bend?
Paul Industries takes ultrapure water work in Northwest Indiana, the Calumet region, South Bend and Elkhart, including boiler makeup plants at industrial sites and laboratory loops at universities. Lake Michigan supplies there run cold much of the year, so RO feed heating is a common part of the design.
Does Paul Industries handle ultrapure water in Evansville and the Ohio River counties?
Yes. Paul Industries builds and services ultrapure and demineralized water systems in Evansville, Jeffersonville and the Ohio River counties. River supplies there swing in turbidity, organics and temperature with the seasons, so pretreatment is designed for the worst month.
What is the semiconductor plant in Indiana that broke ground in 2026?
SK hynix held a ceremonial groundbreaking on August 27, 2026 for a $4 billion advanced packaging production and research facility for high-bandwidth memory in Purdue Research Park, West Lafayette. It is under construction, with cleanroom operation targeted for 2028, and it will rely on ultrapure water.
Why is Indiana water so hard?
Much of Indiana sits on limestone and dolomite bedrock, and carbonate aquifers underlie about half the state. Water moving through that rock dissolves calcium and magnesium, the minerals that make water hard. A USGS survey put median groundwater hardness at roughly 286 to 340 milligrams per liter across aquifer units.
How hard is Indianapolis water for a reverse osmosis plant?
Citizens Energy Group reports Indianapolis water typically between 200 and 350 milligrams per liter as calcium carbonate, varying by treatment plant. That is very hard for RO, so plants use softening, antiscalant or both, and still run at lower recovery than on soft water.
Does an Indiana ultrapure water plant need DNR registration?
If the site can withdraw more than 100,000 gallons a day from all sources combined, the facility registers with the DNR as a significant water withdrawal facility within three months of completion and reports use yearly. Large semiconductor and power plant systems commonly reach that level; laboratory loops do not.
Where can RO reject go at an Indiana site?
RO reject and softener brine go either to the sanitary sewer, once the municipal treatment plant agrees to take them, or to a direct outfall permitted by IDEM. Much of it can be reused first: a second-stage RO, cooling tower makeup where its chemistry allows, or other non-critical uses. Metering shows how much is saved.
How do Indiana winters affect an ultrapure water plant?
Cold feedwater cuts RO flux by roughly 2.5 to 3 percent per degree Celsius, so winter capacity falls unless the RO is sized for cold feed or the feed is warmed. Plants also protect outdoor tanks, piping and reject lines from freezing. Paul Industries often uses plant waste heat to warm the feed.
Is silica a problem in Indiana feedwater?
Silica can limit RO recovery and is tightly controlled for semiconductor and high-pressure boiler users. Indiana groundwater can carry enough to matter, so the feed analysis includes reactive and total silica, and the train is designed to remove both before the polishing loop.
Do Indiana water treatment vessels need a state pressure vessel permit?
Most do not. Softeners are excluded by name, and so are vessels that stay completely water-filled at no more than 180 degrees Fahrenheit, a description that fits most filters, resin vessels and RO housings. Compressed air receivers and vessels sanitized above 180 degrees are checked individually.
What piping material suits an Indiana ultrapure loop?
PVDF is the usual choice for semiconductor and research ultrapure loops because it leaches very little and handles hot-water sanitization; polypropylene suits some lower-grade loops; electropolished stainless suits pharmaceutical systems sanitized with steam or hot water. Paul Industries selects material from the specification and sanitization method.
Can an existing Indiana DI system be upgraded to ultrapure quality?
Often, by adding or upgrading RO and EDI, adding a polishing loop with UV and final filtration, and replacing distribution piping that leaches or traps water. The feedwater pretreatment is checked at the same time, because many older Indiana DI systems were designed around softened water and frequent resin regeneration.
How is ultrapure water quality monitored at an Indiana fab or lab?
Online analyzers measure resistivity, total organic carbon, particles, dissolved oxygen and silica at the loop return and critical points of use, with grab samples for metals, anions and bacteria. Paul Industries installs, calibrates and maintains the analyzers and sets the alarm limits with the owner.
What does it cost to run an ultrapure water plant on Indiana water?
Operating cost covers power, antiscalant and cleaning chemicals, softener salt, resin and membrane replacement, UV lamps and filters, analyzer upkeep, and water and sewer charges on reject. Hard Indiana feed raises the salt, chemical and reject items, which is why recovery and reuse get close attention in the design.
What should an Indiana site send to price an ultrapure water system?
Send the purity specification, flow and peak demand, points of use, a recent feedwater analysis, the site location and drawings, and any qualification requirements. Call 201-450-8280 or use the quote form.
Planning ultrapure water for an Indiana site?
Send the purity specification, flows, points of use, a feedwater analysis and drawings. Call 201-450-8280 or request a quote.
