Paul Industries handles pressure vessel fabrication in Washington, designing, building, testing and installing ASME Section VIII vessels for refineries, aerospace plants, food processors, biotech sites and utilities across the state. Washington is one of the states that regulates unfired pressure vessels as well as boilers, under chapter 70.79 RCW and chapter 296-104 WAC, so a new vessel needs a code nameplate, a National Board registered data report, an installation permit and a first inspection before it runs. Paul Industries delivers each vessel with the documents those steps call for, and repairs, alters and rerates vessels already in Washington service.

Request a quote or call 201-450-8280

Headquarters 256 Shore Drive, Kilmarnock, Virginia
State law Chapter 70.79 RCW covers unfired pressure vessels
Construction code ASME Section VIII Div. 1, 2 and 3, current edition (WAC 296-104-200)
Before service Permit inspection requested 10 working days ahead (WAC 296-104-020)
Refining 5 refineries, 648,200 barrels per day (EIA, January 2026)
Reviewed November 2026

What does pressure vessel fabrication in Washington cover?

Pressure vessel fabrication in Washington covers the design calculations, materials, welding, examination, pressure testing and documentation for air receivers, process reactors, separators, columns, filter housings, heat exchanger shells, autoclaves, jacketed kettles, ammonia receivers and sanitary process vessels, followed by delivery, setting and connection at the plant. The work is the same discipline anywhere in the country, but Washington changes what happens around the vessel: which vessels the state inspects, which construction codes it accepts, what notice it needs before startup, how often the vessel comes back for inspection, and what an earthquake asks of its supports.

The fabrication sequence itself, from data sheet to hydrotest, is explained on the national pressure vessel fabrication page. This page deals with Washington: the law, the permit, the inspection cycle, the seismic and climate conditions, and the industries whose vessels Paul Industries builds in the state.

Which vessels does Washington’s pressure vessel law reach?

Washington’s pressure vessel law reaches the construction, installation and repair of unfired pressure vessels across the state, with a list of exemptions in RCW 70.79.080 that sets the boundary by size, design pressure, location and service. A vessel designed for more than 15 psig and larger than the small-volume limits is normally in scope, and every pressure vessel Washington covers needs a certificate of inspection to operate. Vessels in Seattle are handled by the city’s own boiler and pressure vessel program instead of the state’s.

Washington scope and exemptions for unfired pressure vessels (RCW 70.79.080)
Vessel or conditionStatus under chapter 70.79 RCWWhat it means for a new order
Designed for 15 psig or lessExemptStill built to a recognized standard; no state certificate
5 cubic feet or less, outside places of public assemblyExemptSmall receivers in plants fall here; the same vessel in a public assembly space does not
Under 1.5 cubic feet or under 6 inches in diameterExempt anywhere, any length or pressureSmall filter housings and pipe-sized vessels
Water tank, no air cushion, no direct energy source, ambient temperatureExemptHydropneumatic tanks with an air cushion stay in scope
Inside a city enforcing an equal or stricter ordinanceCity program appliesSeattle permits and inspects these vessels itself
Any other unfired vessel above the limitsIn scopeASME construction, National Board registration, installation permit, certificate

The exemptions are narrower than many buyers expect. A 120-gallon air receiver in a plant is inspected, an expansion tank on a heating system needs a permit, and a jacketed steam kettle in a food plant is listed by name in the permit rule. Paul Industries confirms the status of each vessel at the quote stage, so the schedule includes the permit and inspection wherever they apply.

Washington state pressure vessel code: which construction standards apply?

The Washington state pressure vessel code for new construction is the ASME Boiler and Pressure Vessel Code, current edition, with Section VIII Divisions 1, 2 and 3 for unfired vessels, Section X for fiber-reinforced plastic vessels, Section XII for transport tanks, Section XIII for overpressure protection, and ASME PVHO-1 for pressure vessels for human occupancy. The board of boiler rules also accepts other construction standards approved by the chief inspector that meet the National Board’s registration criteria, and ASME code cases may be used when the chief inspector accepts them.

Two timing details matter on long projects. A new ASME edition may be used from its date of issue, and Washington makes it mandatory 12 months after the board adopts it, so a vessel designed under one edition and built a year later should be checked against the edition in force at construction. The manufacturer's data report for every new standard vessel must also be registered with the National Board, which is how an inspector in Spokane or Tacoma confirms the vessel's design and test data years later. In short, the Washington state boiler and pressure vessel code is the national code plus the state's permit, registration and inspection rules, and Paul Industries designs each vessel to the edition and division the service calls for.

The Washington state pressure vessel permit and first inspection

The Washington state pressure vessel permit is the chief inspector's approval to install or reinstall a vessel, filed by the installer before any installation work starts, and it applies to standard and nonstandard unfired vessels, expansion tanks, jacketed steam kettles, unfired steam boilers, reinstalled vessels and second-hand vessels alike. At least 10 working days before the vessel goes into operation, the installer requests the permit inspection, and until that inspection finds the installation compliant the vessel may be pressurized for testing and nothing more.

The rule has two practical consequences for a project schedule. First, the permit inspection belongs on the critical path between mechanical completion and startup, with the data report, nameplate, relief device data and installation drawings ready for the inspector. Second, an emergency replacement after a leak or failure is allowed, with the chief inspector notified within 48 hours and an immediate inspection requested. Paul Industries prepares the inspection package with each vessel it supplies and installs, so the first inspection checks a complete record rather than waiting on one.

How often do pressure vessels need to be inspected in Washington?

Pressure vessels in Washington need an external inspection every two years, and an internal inspection every two years when the vessel is subject to corrosion and its construction allows entry. A vessel whose contents are known to be noncorrosive needs no internal inspection. Petroleum and chemical plants that run their own owner-user inspection agencies may follow API 510 or NBIC intervals instead, and the rule gives pulp and paper mills a five-year option for dryer rolls.

Washington state pressure vessel inspection intervals (WAC 296-104-100)
Vessel typeExternalInternalDesign choice that helps
Vessel subject to corrosionEvery two yearsEvery two years, where construction permitsManways sized for entry, corrosion allowance, internal coating or lining where the service allows
Vessel not subject to corrosionEvery two yearsNot requiredDocumented noncorrosive service, such as dry instrument air with a dryer
Expansion tanks, air separators, ammonia storage tanks, hot water storage tanksEvery two yearsAt the inspector's discretionInspection openings and drains that let the inspector decide quickly
Vessels in an owner-user inspection programProgram intervalsNBIC or API 510 intervalsThickness monitoring locations marked at fabrication
Pulp or paper dryer rollsProgram intervalsFive years under TAPPI TIP 0402-16, with an accepted written programBaseline thickness and head records delivered with the roll

The grace period is short: an unfired vessel may run up to two months beyond its internal inspection interval, and the certificate is valid to two months beyond the authorized period. Inside Seattle, the city program inspects pressure vessels every two years. Paul Industries builds inspection access into each vessel because a vessel that cannot be entered or read easily costs the owner time at every inspection for the rest of its life.

Designing vessels for Washington’s earthquakes, winters and coast

Designing a vessel for a Washington site starts with seismic loads, because the Puget Sound lowland sits above the Cascadia subduction zone and has a record of deep earthquakes such as the magnitude 6.8 Nisqually earthquake of February 28, 2001, centered about 11 miles northeast of Olympia. Vertical vessels on skirts or legs, horizontal vessels on saddles, and tall columns are designed for the seismic forces in the International Building Code as Washington adopts it in chapter 51-50 WAC, using ASCE 7 ground motions for the site. The 2021 editions have applied since March 15, 2024, and the 2024 editions are set to take effect on May 3, 2027.

Seismic design reaches past the shell. Anchor bolts, skirt base rings and saddle slots are sized for overturning and sliding; nozzle loads include the movement of connected piping in an earthquake; and tall columns get a check of the period and damping that the site's soil class implies. Paul Industries designs the vessel and its supports together and supplies anchor bolt layouts and foundation loads early, because foundations are usually poured before the vessel arrives.

Temperature and air drive the other choices. East of the Cascades, outdoor vessels at Columbia Basin and Spokane sites see hard winter cold, so the minimum design metal temperature is set from the coldest metal temperature the vessel can reach in service or during a winter pressure test, and carbon steel is impact tested or selected under the Section VIII exemption curves accordingly. West of the mountains, marine air and rain put the emphasis on coating systems, insulation jacketing and drains that keep water out from under the insulation, which is where corrosion under insulation begins.

Vessels for Washington’s refineries, aerospace plants and food processors

Washington’s demand for pressure vessels comes from a small number of large refineries, a major aerospace manufacturing base around Everett and Renton, a food processing industry concentrated in the Columbia Basin and central valleys, and biotech manufacturing around Seattle, Bothell and Redmond. Each brings its own vessel types and its own documentation expectations.

Washington industries and the vessels they order
IndustryTypical vesselsWashington consideration
Petroleum refining, Anacortes, Whatcom County and TacomaSeparators, drums, columns, exchanger shells, hydrogen and amine service vesselsRefinery process safety rule, chapter 296-67 WAC Part B; API 510 owner-user inspection
Aerospace, Everett and RentonComposite curing autoclaves, air receivers, process tanks under pressureQuick-actuating closures and interlocks; large-diameter vessels with door hinges and seals
Food processing, Columbia Basin, Yakima and WenatcheeAmmonia receivers, jacketed kettles, blanchers and cookers under steam, air receiversKettles listed in the permit rule; ammonia storage tank internals at the inspector's discretion
Biotech and pharmaceutical, Seattle, Bothell and RedmondSanitary process vessels, media and buffer vessels, clean steam and WFI vesselsASME BPE finishes and drainability with the same Section VIII stamp and Washington permit
Utilities, hospitals and campusesExpansion tanks, deaerators, blowdown tanks, hydropneumatic tanksExpansion tanks need a permit; hydropneumatic tanks with an air cushion stay in scope

Refining is the heaviest vessel market in the state. The EIA counted five operating refineries in Washington with 648,200 barrels per calendar day of crude distillation capacity on January 1, 2026, and since December 27, 2024 those plants have operated under a refinery-specific process safety rule, Part B of chapter 296-67 WAC, which adds damage mechanism reviews and a pre-startup safety review for all turnaround work. A replacement vessel for a Washington refinery therefore arrives with the material certifications, weld maps, examination reports and design basis that the mechanical integrity file and the review need.

Aerospace adds a different vessel. Boeing's Composite Wing Center in Everett cures composite wing spars under heat and pressure in an autoclave, and autoclaves of that kind are unfired pressure vessels with quick-actuating closures, which ASME Section VIII treats with specific interlock and closure requirements. Paul Industries fabricates and installs autoclave and curing vessels, process receivers and the steam, air and nitrogen systems that serve them.

How a Washington vessel order runs from data sheet to service

A Washington vessel order runs through five stages: the process data sheet and code basis, design and drawings, fabrication and examination, testing and documentation, and delivery, setting and the permit inspection. The data sheet fixes design pressure and temperature, the minimum design metal temperature, corrosion allowance, materials, nozzle schedule, seismic and wind data for the site, and the Section VIII division. Design produces the calculations, general arrangement and detail drawings, and anchor bolt and foundation loads for the civil designer.

Fabrication follows qualified weld procedures, with radiography or ultrasonic examination as the code and the specification require, then a hydrostatic or pneumatic test witnessed by the Authorized Inspector. The vessel leaves with its nameplate, the manufacturer's data report for National Board registration, material test reports, the weld map and examination records, and the relief device data. Paul Industries then sets the vessel, connects it, and has the permit inspection package ready ten working days before the planned startup, which is the step that closes the job in Washington. Vessels too large to move as one piece are shipped in sections and completed at the site under the same code inspection.

Schedule on a Washington vessel is set by three items more than by welding hours: plate and forging availability for the chosen material, the design review cycle with the owner's engineer, and the window for the permit inspection and startup. Alloy and clad plate, large forged nozzles and heads above standard sizes carry the longest material lead, so Paul Industries confirms them before the drawings are final. Design review moves fastest when the data sheet arrives with the seismic site data, the minimum design metal temperature and the nozzle loads already fixed. At the other end, a winter hydrostatic test outdoors east of the Cascades needs heated water or an enclosed test area, and that choice is made early, alongside the minimum design metal temperature, so the test never becomes the coldest load the steel sees.

What paperwork comes with a Washington pressure vessel?

A Washington pressure vessel comes with a records package that serves three readers: the state or city inspector at the permit inspection, the plant's mechanical integrity or maintenance program, and whoever repairs or rerates the vessel decades later. The core is the ASME manufacturer's data report, U-1 or U-1A for Division 1, which is registered with the National Board and carries the design pressure and temperature, materials, thicknesses, examination and test data. Behind it sit the calculations, the as-built drawings, the material test reports traced to heat numbers, the weld map with procedure and welder identification, radiography or ultrasonic reports, the hydrostatic or pneumatic test record and a nameplate rubbing or photograph.

Washington adds the installation side: the permit, the relief device sizing and set pressure data, anchor bolt and foundation drawings for the seismic design, and the installation drawings the inspector checks against the vessel in place. Refinery and chemical plant buyers usually add positive material identification records and baseline thickness readings at marked monitoring locations, which feed straight into an API 510 program, and biotech buyers add surface finish, passivation and drainability records for sanitary vessels. Paul Industries assembles this package as the vessel is built, indexed so a plant engineer can find the weld map or the relief data years later without searching a filing cabinet.

Repairs, alterations and rerates on Washington vessels

Repairs, alterations and rerates on vessels in Washington service are made under the National Board Inspection Code, Part 3, and the National Board R program, with the Authorized Inspector consulted before work begins, and the process checklist and the R-1 or R-2 report reach the jurisdiction within 45 days of the work. A rerate to a higher pressure or temperature is an alteration, so it needs design calculations, revised nameplate data and an R-2. Repairs to a nonstandard vessel need the chief inspector's authorization first.

Second-hand vessels are a common Washington question because plants buy used equipment from closures in other states. A standard vessel with its ASME nameplate and National Board registration can be reinstalled under a reinstallation permit and inspection; a nonstandard used vessel dating from 1952 or later goes to the board of boiler rules for approval before use, with drawings, photographs, service history, calculations and an engineering evaluation of design and condition. Paul Industries evaluates used vessels, performs the repairs and rerates they need, and documents them for the inspector, with hydrostatic testing to prove each result.

What does pressure vessel fabrication in Washington cost?

Pressure vessel fabrication in Washington is priced from the data sheet, and the cost drivers are the size and wall thickness, the material and any alloy cladding, the Section VIII division, the examination required, seismic supports and anchorage, internals and jackets, sanitary finishes where they apply, and the size of the documentation package. Shipping and rigging weigh more in Washington than buyers expect, because large vessels for Washington sites move by barge or as oversized road loads, and vessels bound for eastern Washington cross the Cascades.

The state adds few direct costs: the installation permit and inspection fees, the National Board registration, and for repairs and rerates the R program documentation. Paul Industries gives a budget price from a preliminary data sheet and a firm price once the design basis, materials and examination are settled, with fabrication, testing, freight, setting and connection shown as separate lines.

Who fabricates pressure vessels for Washington plants?

Paul Industries fabricates pressure vessels for Washington plants, designing and building ASME Section VIII vessels, testing them, delivering them with their code documents, and setting and connecting them for refineries, aerospace manufacturers, food processors, biotech sites, hospitals and utilities. Owners choose supply-only delivery of a code-nameplated, documented vessel, design-build from a process duty, or complete installation through the permit inspection. From its headquarters at 256 Shore Drive in Kilmarnock, Virginia, Paul Industries, an East Coast contractor formerly based in northern New Jersey and then Pennsylvania, builds vessels for Washington sites, for plants in all 50 states and for international projects.

Vessel buyers in the headquarters state will find the same approach on the pressure vessel fabrication in Virginia page, and Gulf Coast refinery practice is set out on pressure vessel fabrication in Texas. Within Washington, vessels connect to boiler repair in Washington for deaerators and blowdown tanks, tank fabrication in Washington for atmospheric storage, process piping in Washington for the lines that tie vessels into the process, and industrial welding services in Washington for code repairs at the plant. Exchanger shells built to the same code are covered under heat exchangers.

Pressure vessel work from Paul Industries in Washington

Paul Industries designs, fabricates, tests, supplies, installs, repairs, alters and rerates pressure vessels for plants from Anacortes, Everett and Seattle to Tacoma, Vancouver, the Columbia Basin, Yakima and Spokane, with the permit inspection and National Board records ready at startup. Send the data sheet or the process duty, the site location, the design code and any existing vessel's nameplate and records. Call 201-450-8280 or request a quote. More Washington process, water and piping services are listed on the Washington hub, and Pacific region work on the West Coast page.

Standards referenced: Chapter 70.79 RCW · Chapter 296-104 WAC · ASME BPVC Section VIII Divisions 1, 2 and 3 · ASME BPVC Sections X, XII and XIII · ASME PVHO-1 · National Board Inspection Code · API 510 · TAPPI TIP 0402-16 · Chapter 296-67 WAC Part B · International Building Code as adopted in chapter 51-50 WAC · ASCE 7 · ASME BPE

Frequently asked questions

Who builds pressure vessels for refineries at Anacortes, Ferndale and Tacoma?

Paul Industries builds ASME Section VIII vessels for refineries at Anacortes, Ferndale and Tacoma, including separators, drums, column sections, exchanger shells and replacement vessels for turnarounds. Each vessel ships with material certifications, weld maps, examination reports and the design basis that the refinery's mechanical integrity file and Washington's Part B process safety rule call for, with the data report ready for National Board registration.

Does Paul Industries supply vessels for Everett and Bothell aerospace and biotech plants?

Yes. Paul Industries supplies and installs vessels for aerospace and biotech plants in Everett, Bothell, Redmond and Seattle: autoclaves and curing vessels with quick-actuating closures, air and nitrogen receivers, and sanitary process vessels built to ASME BPE finishes and drainability under the same Section VIII nameplate. Each vessel goes through Washington's installation permit and first inspection, or Seattle's permit inside the city.

Who fabricates ammonia receivers and process vessels for Columbia Basin plants in Moses Lake and Pasco?

Paul Industries fabricates ammonia receivers, oil pots, jacketed kettles, steam cookers and air receivers for food and cold storage plants in Moses Lake, Quincy, Othello, Pasco and the Tri-Cities. Washington lists ammonia storage tanks among the vessels whose internal inspection is left to the inspector's discretion, so drains, openings and nameplate placement are designed for quick external checks. Winter cold sets the minimum design metal temperature on outdoor units.

What is considered a pressure vessel under Washington law?

Under chapter 70.79 RCW, a pressure vessel is an unfired vessel that holds pressure above atmospheric, and the state regulates it unless an exemption applies. The main exemptions are vessels designed for 15 psig or less, vessels of 5 cubic feet or less outside places of public assembly, vessels under 1.5 cubic feet or under 6 inches in diameter, and water tanks with no air cushion at ambient temperature.

Does a small air receiver in a Washington plant need a certificate?

A small air receiver needs a Washington certificate once it exceeds the exemption limits. Receivers of 5 cubic feet or less are exempt when they are outside places of public assembly, and any vessel under 1.5 cubic feet or under 6 inches in diameter is exempt everywhere. A typical 80 or 120 gallon plant receiver is larger than both limits, so it needs a permit, an inspection and a posted certificate.

What are the Washington state pressure vessel requirements before startup?

The Washington state pressure vessel requirements before startup are an ASME code vessel built to the current edition, a manufacturer's data report registered with the National Board, an installation permit approved before installation begins, and a permit inspection requested at least 10 working days before operation. Until that inspection passes, the vessel may be pressurized for testing only. Paul Industries prepares the package so the inspection runs on schedule.

Are expansion tanks and jacketed kettles covered by Washington's permit rule?

Expansion tanks and jacketed steam kettles are both named in Washington's installation permit rule, WAC 296-104-020, along with unfired pressure vessels, water heaters, pool heaters, unfired steam boilers and second-hand objects. A kettle replaced in a food plant or an expansion tank added to a heating system therefore needs a permit and an inspection before use, and Paul Industries includes both steps in the installation.

Can a Washington refinery inspect its vessels under API 510?

A Washington petroleum or chemical plant with its own owner-user inspection agency may use API 510 as its standard for inspecting unfired pressure vessels, and vessels in an owner-user program may follow NBIC or API 510 intervals instead of the state's fixed two-year cycle. Repairs and alterations still follow the NBIC repair rules and the 45-day filing. Paul Industries marks thickness monitoring locations at fabrication to support the program.

How are pulp and paper dryer rolls inspected in Washington?

Pulp and paper dryer rolls in Washington may be inspected on a five-year basis under TAPPI TIP 0402-16, revised 2011, when the owner has a written inspection program accepted by the inspector. Otherwise they follow the normal unfired vessel cycle. A new or repaired roll should come with baseline shell and head thickness readings, so the five-year program has a starting point.

How should a vertical vessel be anchored for a western Washington earthquake?

A vertical vessel in western Washington is anchored for the seismic forces of the International Building Code as Washington adopts it, using ASCE 7 ground motions for the site's soil class. The skirt, base ring, anchor chairs and bolts are sized for overturning and shear, and nozzle loads include piping movement. Paul Industries designs the vessel and supports together and issues foundation loads early.

What minimum design metal temperature suits a vessel east of the Cascades?

The minimum design metal temperature for a vessel east of the Cascades is set from the coldest metal temperature it can reach outdoors in winter, during startup or during a cold-weather pressure test. Carbon steel is then either impact tested or chosen under the Section VIII exemption curves for that temperature. Paul Industries fixes the value on the data sheet before materials are ordered, because changing it later means new plate.

Is a composite curing autoclave a pressure vessel in Washington?

A composite curing autoclave is an unfired pressure vessel in Washington when its size and design pressure exceed the exemption limits, so it needs ASME construction, National Board registration, an installation permit and periodic inspection. Its quick-actuating door must have the interlocks Section VIII requires, so the door cannot open under pressure. Paul Industries builds and installs autoclaves with their steam, air and nitrogen supplies.

Can a used pressure vessel from another state be installed in Washington?

A used ASME vessel with its nameplate and National Board registration can be installed in Washington under a reinstallation permit and inspection, often after a thickness survey and hydrostatic test. A nonstandard vessel of 1952 or later construction is a board decision: the owner submits drawings, history and calculations with an engineering evaluation, and the board approves it before use. Paul Industries evaluates and refurbishes used vessels for that process.

How long does a pressure vessel certificate last in Washington?

A Washington pressure vessel certificate runs with the inspection cycle and stays valid up to two months beyond the authorized inspection period, so most vessels hold a certificate covering a two-year external interval. A vessel may also run up to two months past its internal interval. The certificate is posted with the vessel or kept in a protective container for portable units.

How is a pressure vessel Seattle permits handled differently?

A pressure vessel Seattle permits is handled by the city's Department of Construction and Inspections under the Seattle Boiler and Pressure Vessel Code, because state law exempts vessels in cities with equivalent ordinances. The city requires an installation permit for each vessel, ASME construction and, with some exceptions, National Board registration, and inspects pressure vessels every two years. Paul Industries prepares the same documents for the city as for the state.

Which pressure vessel safety standards apply to relief valves in Washington?

Relief devices on new Washington vessels are designed under ASME Section XIII, which the state lists among its construction standards, and existing relief devices are installed, inspected and repaired under Part 4 of the National Board Inspection Code. Each vessel ships with relief device sizing, set pressure and capacity data. Paul Industries supplies, installs and replaces relief valves along with the vessels they protect.

What does Paul Industries need to quote a pressure vessel for a Washington site?

Send the data sheet or process duty: design pressure and temperature, volume or dimensions, materials, corrosion allowance, nozzle list, the Section VIII division, and any sanitary finish or jacket. Add the site location so seismic and winter conditions can be set, plus delivery constraints. For a repair or rerate, send the nameplate, data report and inspection history. Paul Industries returns a design basis, schedule and price.

Ordering or rerating a pressure vessel for a Washington plant?

Send the data sheet or process duty, the site location and any existing nameplate and inspection records. Call 201-450-8280 or request a quote.