Paul Industries provides chiller repair in California for centrifugal, screw, scroll and absorption chillers at manufacturing plants, biotech and food facilities, hospitals, campuses and data centers, from leak repair and tube work to compressor overhauls, retrofits and replacement. California layers its own refrigerant program on top of the federal one, with a 14-day leak repair rule for covered systems and a ban on high-GWP refrigerants in new chillers, so a repair decision there carries more regulation than in most states. Paul Industries diagnoses, repairs, documents and, where repair no longer pays, replaces the machine.

Request a quote or call 201-450-8280

Headquarters 256 Shore Drive, Kilmarnock, Virginia
State leak rule CARB: leaks repaired within 14 days on covered systems over 50 lb
New chillers Refrigerant GWP below 750 since January 1, 2024 (CARB)
Hottest region El Centro July normal high 107 F (NOAA, 1991-2020)
Electricity Industrial average 21.53 cents/kWh; US 8.13 (EIA, 2024)
Reviewed November 2026

What makes chiller repair in California different?

Chiller repair in California is different because two refrigerant programs apply at once: the California Air Resources Board’s Refrigerant Management Program, which requires leak inspections and repair within 14 days on covered systems, and the federal Emissions Reduction and Reclamation rule, which added leak rate thresholds for HFC appliances on January 1, 2026. Add a state refrigerant ceiling for new chillers, industrial electricity at more than two and a half times the national average, seismic rules for any replacement, and climates that run from 54-degree San Francisco summer nights to 107-degree El Centro afternoons, and the right repair depends heavily on where the machine sits.

The national guide to faults, symptoms and repair methods is the chiller repair page. This page covers the California rules, climate and decisions that sit on top of those methods.

CARB’s Refrigerant Management Program and which chillers it covers

CARB’s Refrigerant Management Program covers non-residential facilities whose single largest refrigeration system holds more than 50 pounds of a high-GWP refrigerant, meaning any refrigerant with a global warming potential of 150 or more plus all ozone-depleting refrigerants. Facilities whose only systems are air conditioning used exclusively for comfort cooling are outside the facility requirements, but a chiller over 50 pounds that serves both comfort and process cooling falls in the program’s “other refrigeration” category and is covered.

That line matters at California plants. A biotech building whose chillers also cool process equipment, a food plant with glycol chillers, a data center whose chillers serve a computer room, or a hospital chiller that also serves an MRI or laboratory process load can bring the facility into the program. Required service practices are broader still: they apply to anyone installing, servicing, repairing or disposing of any stationary appliance that contains a high-GWP refrigerant, comfort chillers included, and CARB’s guidance says refrigerant should not be added to any appliance with a known leak.

Refrigerant Management Program requirements by system size (CARB)
Size categoryLargest system’s high-GWP chargeLeak inspection frequencyWhat it means for chiller service
SmallMore than 50 pounds, less than 200 poundsAnnual, plus whenever refrigerant is addedAnnual inspection folded into the service visit; records kept on site
Medium200 pounds to less than 2,000 poundsQuarterly, plus whenever refrigerant is addedTypical for large centrifugal and screw machines; quarterly inspection schedule
Large2,000 pounds or moreMonthly, with automatic leak detection on systems run year round; quarterly where the system runs seasonally or has major components outdoorsCentral plants with several big machines; monitoring calibrated annually
All covered sizesAny leak foundRepair within 14 days of detection, with more time allowed in certain conditionsParts and refrigerant planned so the repair fits the window

The 14-day repair window is far shorter than the federal 30 days, so a California repair plan starts with parts availability. Paul Industries carries out the inspections, repairs within the state window, records each inspection, repair and refrigerant addition, and keeps the records in the format the program requires for registration and reporting.

How the state and federal leak rules fit together

The state and federal leak rules fit together by stacking: a California chiller covered by both must meet the stricter requirement on each point. The federal Emissions Reduction and Reclamation rule, in force since January 1, 2026 for appliances holding 15 pounds or more of an HFC, requires a leak rate calculation each time refrigerant is added, with leak rate triggers of 10 percent a year on comfort cooling and 30 percent on industrial process refrigeration (20 percent for commercial refrigeration), a 30-day repair deadline once a trigger is crossed, stretched to 120 days when an industrial process has to shut down, and verification testing afterward.

California’s program has no leak rate threshold to wait for: on a covered system, any leak found is repaired within 14 days. In practice Paul Industries runs one procedure that satisfies both, calculating the federal leak rate at each addition, repairing within the state window, performing the federal verification tests after the repair, and filing a single record that shows both programs’ steps for the same event.

Repair or replace under California’s 750 GWP limit

The repair or replace decision in California changes because a replacement chiller cannot use the refrigerant the old one held in most cases: since January 1, 2024, CARB’s HFC regulation has prohibited new chillers that use a refrigerant with a global warming potential of 750 or more, which takes R-134a and R-410A out of new machines, including process chillers above 35 degrees Fahrenheit. Existing machines are unaffected and keep running and being serviced on their current refrigerant.

That rule makes repair more attractive for sound machines and replacement a larger project when it comes. A new low-GWP chiller may have a different refrigerant safety class, a different footprint or weight, and different machinery room requirements under ASHRAE 15 and the 2025 California Mechanical Code. It also needs seismic anchorage designed to ASCE 7-22 under the 2025 California Building Code, which often means new pads or curbs.

Several of the lower-GWP refrigerants offered in new chillers carry the A2L safety class under ASHRAE 34, meaning lower flammability, and that classification brings its own requirements for refrigerant detection, ventilation and electrical equipment in the machinery room. A plant room built around an R-134a machine in the 1990s may need new detectors, revised ventilation and updated signage before an A2L machine can go in. Paul Industries surveys the machinery room during the repair or replace study, so the replacement budget includes the room changes along with the chiller, and the owner is not surprised by them at plan check.

Repair, retrofit or replace signals for a California chiller
ConditionLeans toward repairLeans toward replacement
RefrigerantR-134a or R-410A machine in sound condition; serviceable for yearsR-22 with a large leak; R-123 with no supply plan beyond 2030
Leak historySingle leak, repaired within 14 days and verifiedRepeated leaks driving state inspections and federal leak rate exceedances
Compressor and motorComponent fault such as bearings, seals or vane actuatorRepeated failures or a damaged impeller or rotors
TubesLimited wall loss on eddy currentWidespread pitting or scale damage
EnergyMeasured efficiency close to ratingLarge gap to a new machine at California power prices
SiteReplacement would need new structure, rigging paths or a larger machinery roomAccess, structure and power ready for a new machine

Energy weighs more here than in most states. As an illustration, a 400-ton chiller running 2,500 equivalent full-load hours a year that improves by 0.20 kilowatts per ton after replacement saves about 200,000 kilowatt-hours, roughly $43,000 a year at 21.53 cents, the state’s 2024 industrial average per EIA. Those inputs are assumptions chosen for the example; the machine’s measured kilowatts per ton, its real run hours and the site’s utility rate decide the true figure, and Paul Industries calculates it from them.

California climates and what they do to chillers

California climates stress chillers in five distinct ways, and the region where a machine runs predicts the faults it develops. Fog-belt San Francisco, with July normals of 66 and 54 degrees Fahrenheit, runs chillers lightly and often favors economizers; inland valleys push condensing pressures high for months.

Chiller repair: Bay Area and Silicon Valley

Chiller repair Bay Area facilities need is shaped by a mild, marine climate and year-round process loads. Biotech buildings in South San Francisco and the Peninsula, semiconductor and equipment makers in Silicon Valley and data centers in Santa Clara run chillers through winter for process and computer rooms, often at low load, so surge control, low-load staging and economizer changeover are frequent service items. Salt air near the bay corrodes air-cooled condenser coils.

Chiller repair: Los Angeles, Orange County and the Inland Empire

Chiller repair Los Angeles buildings call for most often comes from warm summer nights, with Los Angeles July normals of 82 and 65 degrees, and from hard water. Water across much of Southern California carries far more hardness than San Francisco’s Sierra supply, so condenser tubes on open tower systems scale faster and need more frequent cleaning. Riverside’s 93-degree July normal high adds long periods of high head pressure on inland plants, and wildfire ash coats air-cooled condenser coils during fire seasons.

Chiller service: San Diego and the Imperial Valley

Chiller service San Diego plants rely on deals with a narrow daily temperature swing, 75 and 66 degrees in July, and a humid marine layer, which keeps chillers running through the night for dehumidification in biotech, defense and hospital buildings. East of the mountains, El Centro’s 107-degree July normal high pushes air-cooled machines to their limits, and condenser coil cleaning, fan motor service and refrigerant charge checks before summer prevent most failures there.

Industrial chiller repair in the Central Valley

Industrial chiller repair in the Central Valley follows the harvest. Food processors, dairies, wineries and cold storage plants around Fresno, Bakersfield, Modesto and Stockton run glycol and process chillers hardest from summer into autumn, with Fresno and Bakersfield July normal highs of 98 degrees. Repairs are planned for the off-season, and glycol strength, pump seals and heat exchanger condition are checked at the same visit. Process machines on a single line are covered on process chillers.

Tube cleaning, scale and how often should chiller tubes be cleaned?

How often should chiller tubes be cleaned depends on the water and the run hours, but on open cooling tower systems in California most owners clean condenser tubes at least once a year, before the cooling season, and more often where the make-up water is hard or the tower runs at high cycles of concentration. Evaporator tubes on closed chilled water loops need cleaning far less often, usually when approach temperatures show fouling.

Paul Industries tracks condenser approach temperature between cleanings, because a rising approach shows fouling early and points to the right date for the next cleaning. Tubes are cleaned mechanically with rotating brushes, or chemically where scale has hardened, and eddy current testing measures wall loss and pitting so the owner knows whether to plug tubes, retube the bundle or plan a replacement. Scale that returns year after year starts in the tower basin and the make-up water, which is why a tube cleaning visit often ends with a look at the tower itself; cooling tower repair and a review of the treatment chemistry are frequent next steps.

Common chiller faults in California conditions and the first checks

Common chiller faults in California conditions follow the climate and the water: high head pressure trips on inland afternoons, low-load surge and short cycling on mild coastal days, scaled condenser tubes where make-up water is hard, and refrigerant leaks at corroded joints near the coast. Each has a short list of first checks that a technician runs before any part is ordered, and the 14-day state leak window makes fast, accurate diagnosis worth more here than elsewhere.

Frequent California chiller faults, likely causes and first checks
SymptomLikely California causeFirst checks
High head pressure trips on hot afternoonsFouled condenser coils or tubes; ash on coils; tower unable to hold setpoint in inland heatCondenser approach, coil condition, tower fan and fill, condenser water flow
Surge or short cycling on mild daysLow load against high lift; condenser water reset too warm; staging too aggressiveLoad profile, condenser water setpoint and reset, minimum load and staging logic
Capacity lost over a seasonScale on condenser tubes from hard make-up water and high cyclesApproach trend since the last cleaning, tower water chemistry, cycles of concentration
Refrigerant lossCorroded brazed joints near salt air; vibration fatigue; failed sealsLeak search with electronic detector and soap test; leak rate calculation; 14-day window starts
Low evaporator pressure or freeze alarmLow chilled water flow; wrong glycol strength on process loopsFlow switch and pump, strainer, glycol concentration, low-temperature setpoints
Purge running constantly on low-pressure machinesAir leaking into an R-123 machine through gaskets or tubesPurge run time trend, pressure rise test during shutdown, gasket condition

Paul Industries starts every diagnosis with the machine’s own trend data where the controls record it, then measures approaches, pressures and temperatures on site and compares them with the clean baseline. The repair is ordered only after the cause is confirmed, so the owner pays for the fix the data points to rather than for a sequence of guesses, and the leak records required by both refrigerant programs are written as the work happens.

Registration, reporting and records under California’s refrigerant program

Registration, reporting and records under California’s refrigerant program fall on the facility owner, and the service contractor supplies most of the content. Covered facilities register with CARB and report on their refrigerant systems, the schedule having been phased in by facility size starting in 2012, and they keep on-site records of every inspection, repair and refrigerant purchase or shipment.

A chiller’s file therefore holds more than service tickets: the leak inspection dates and results, each leak found with its location and repair date, refrigerant added and recovered by the pound, verification tests after repairs, and, for federal purposes, the leak rate calculated at every addition. Paul Industries writes each entry at the time of service, in a format that rolls up into the owner’s annual report, and flags any machine whose leak history suggests a retrofit or replacement plan is due.

Keeping cooling on during a California chiller repair

Keeping cooling on during a California chiller repair starts with the 14-day leak window and the load the building carries during that window. A leaking machine on a covered system cannot simply sit idle waiting for a convenient outage, so the plan sets out which machines carry the load, whether noncritical areas can be shed, and whether a temporary chiller is needed while the repair is made.

Hospitals, biotech plants and data centers usually have redundant machines, and the repair proceeds one machine at a time with the remaining capacity checked against the expected load. Where redundancy is thin, Paul Industries connects a temporary chiller through valved, capped connections on the chilled water headers, installing permanent connections during the repair if the plant lacks them. Temporary units in California need their own seismic restraint for the duration, a level pad, a power source and, for water-cooled rentals, a condenser water arrangement. The returning machine is started on load, its approaches compared with the baseline, and the temporary unit removed once the repaired chiller has carried the afternoon peak.

Chiller service and repair contracts for California facilities

Chiller service and repair contracts for California facilities combine the manufacturer’s maintenance schedule with the state’s inspection calendar, so a single program covers both. Paul Industries builds each contract around the machine’s size category under the Refrigerant Management Program, so the annual, quarterly or monthly leak inspection lands on the same visits as spring startup, autumn shutdown and log review. Oil samples, vibration trending, tube work and eddy current tests follow the manufacturer’s hours, and where a machine runs on reclaimed refrigerant, its purity is checked against AHRI 700.

Towers, condenser pumps, water treatment and the plant piping fit in the same agreement, an advantage in Southern California, where the scale that ends up on condenser tubes begins in the tower. Machines from every major maker are covered, with dedicated pages for Trane chiller repair, York chiller repair and Carrier chiller repair; the plant piping standards are on process piping in California.

Chiller repair cost in California: parts, refrigerant and replacement

Chiller repair cost in California is driven by the fault and its parts, refrigerant recovery and recharge, the machine’s size and type, access and rigging, temporary cooling, and the documentation the state and federal leak rules require. Refrigerant is often a large variable: HCFC refrigerants now come only from reclaimed or previously produced supply, and HFC prices follow each step of the federal phasedown.

Chiller replacement cost adds a new low-GWP machine, rigging, seismic anchorage and often new pads or curbs, electrical changes, piping modifications, machinery room updates for the new refrigerant, removal and recovery from the old unit, and startup. Paul Industries quotes a repair once the diagnosis is done, listing refrigerant pounds, parts and hours as separate lines, and whenever a repair is large it adds a replacement budget beside it. A replacement is offered three ways: the new chiller supplied for the owner’s installation, a design-build plant upgrade, or a turnkey changeover that includes removing the old machine.

Who repairs chillers in California?

Paul Industries repairs chillers in California, taking leak repair, compressor and motor work, tube cleaning and eddy current testing, controls and starter repair, overhauls, retrofits and replacements at plants, hospitals, campuses and data centers from the Bay Area and Sacramento to Los Angeles, the Inland Empire, San Diego and the Central Valley. Paul Industries is an East Coast contractor headquartered at 256 Shore Drive in Kilmarnock, Virginia, and takes chiller work across California and in all 50 states.

Chillers sit inside larger systems, so one contract covering the chiller, tower, pumps and piping lets one diagnosis follow a fault wherever it starts. Heating plants on the same campus are covered on boiler repair in California, and data center plants on data center cooling in California. Chillers that hold cleanroom temperature or cool laboratory process water tie into the systems described on cleanrooms in California and ultrapure water systems in California. Owners with buildings in several states can compare this page with chiller repair in Virginia, the headquarters state, and chiller repair in Florida. The West Coast page covers the other Pacific states.

Next step for a California chiller

Paul Industries repairs, overhauls, retrofits, maintains, supplies and installs chillers across California with the state and federal refrigerant records kept for every event. A first diagnosis goes faster with the nameplate data, refrigerant type and pounds of charge, recent alarms and logs, and the latest leak inspection on file. Call 201-450-8280 or request a quote. Other process, water and piping services in the state are listed on the California page.

Standards referenced: CARB Refrigerant Management Program (17 CCR 95380 to 95398) · CARB HFC Regulation (17 CCR 95371 and following) · EPA Emissions Reduction and Reclamation rule, 40 CFR 84.106 · Clean Air Act Section 608 · 2025 California Mechanical Code (Title 24, Part 4) · 2025 California Building Code and ASCE 7-22 · ASHRAE 15 · ASHRAE 34 · AHRI 700

Frequently asked questions

Who handles chiller repair in San Francisco, Oakland and South San Francisco?

Paul Industries handles chiller repair in San Francisco, Oakland, South San Francisco and across the Peninsula and East Bay, for biotech buildings, hospitals, campuses and offices. Mild summers mean many Bay Area chillers run at low load for long periods, so surge control, staging and economizer changeover are common repair items, along with corroded air-cooled coils near the water.

Does Paul Industries repair chillers in Santa Clara and San Jose data centers and fabs?

Yes. Paul Industries repairs chillers serving data centers, semiconductor equipment makers and research buildings in Santa Clara, San Jose and Sunnyvale. Process and computer room chillers there often fall under CARB’s Refrigerant Management Program, so repairs follow the 14-day leak window and the facility’s inspection schedule, one machine at a time with redundancy confirmed.

Who provides chiller service in Sacramento, Fresno and Bakersfield?

Paul Industries provides chiller service and repair in Sacramento, Fresno, Bakersfield and the rest of the Central Valley for food plants, dairies, wineries, hospitals and campuses. July normal highs of 94 to 98 degrees Fahrenheit mean long periods of high head pressure, so condenser coil and tube cleaning before summer and glycol checks before harvest prevent most failures.

Does Paul Industries repair chillers in Riverside, San Bernardino and Orange County?

Yes. Paul Industries repairs chillers at plants, warehouses with process cooling, hospitals and offices in Riverside, San Bernardino and Orange County. Inland machines run hot summers and see wildfire ash on air-cooled coils, while hard water scales condenser tubes on tower systems, so coil cleaning and tube cleaning are the most frequent service items there.

Who services chillers in California hospitals during the 14-day leak window?

Paul Industries services hospital chillers across California, planning each repair around backup capacity, the 14-day state leak window and the hospital’s outage procedures. Remaining machines are checked against the expected load, temporary cooling is connected for critical areas where redundancy is thin, and the repaired machine is tested under load before it rejoins the plant.

Does CARB's refrigerant program apply to an office building's chillers?

If every system at the facility is air conditioning used only for comfort cooling, the facility requirements of CARB’s Refrigerant Management Program do not apply. Required service practices still apply to anyone servicing the chillers, including the rule against adding refrigerant to an appliance with a known leak. A chiller over 50 pounds that also serves a process load brings the facility into the program.

How fast must a leak be repaired on a California chiller?

On a system covered by CARB’s Refrigerant Management Program, any leak must be repaired within 14 days of detection, with additional time allowed in certain conditions. Federal rules add a leak rate calculation at every refrigerant addition for HFC appliances of 15 pounds or more, with repair within 30 days once a threshold is exceeded. Paul Industries plans to the stricter state window.

Can a new chiller in California use R-134a or R-410A?

New chillers in California have been limited to refrigerants below 750 GWP since the start of 2024, a CARB ceiling that excludes R-134a and R-410A from new machines, including process chillers above 35 degrees Fahrenheit. Existing R-134a and R-410A chillers keep running and can be repaired and recharged on their original refrigerant.

Does an R-22 machine still earn a repair under California's leak rules?

Sometimes. Production and import of R-22 ended in 2020, so service depends on reclaimed supply, and a large leak is expensive to recharge. Under California’s 14-day repair rule, an R-22 machine with repeated leaks also brings repeated inspections. Paul Industries repairs sound R-22 machines for short horizons and prices a low-GWP replacement alongside so the owner sees both paths.

Which CSLB classification covers chiller repair in California?

California’s C-38 Refrigeration classification covers the control of air, liquid or gas temperatures below 50 degrees Fahrenheit, which describes the refrigeration side of most chillers, and C-20 covers heating, ventilating and air-conditioning systems. State law requires a license in the matching class once a job reaches $1,000 or needs a permit. Owners confirm the classification during contracting.

How often should a Southern California cooling tower system have its chiller tubes cleaned?

At least once a year before summer on most open tower systems, and more often where hard make-up water and high cycles of concentration scale tubes quickly. Condenser approach temperature is a reliable guide: once it rises a few degrees above the clean baseline, capacity and efficiency are falling. Paul Industries trends approach between cleanings and sets the schedule from that data.

Why does a California chiller lose capacity during a wildfire season?

Ash and smoke particulate settle on air-cooled condenser coils and cooling tower fill, reducing airflow and heat transfer exactly when inland temperatures peak. Head pressure rises, capacity falls, and machines trip on high pressure. Coil cleaning after smoke events, filters or screens on intakes where practical, and a pre-summer coil inspection restore most of the lost capacity.

Does replacing a chiller in California need seismic anchorage?

Yes. A replacement chiller is installed under the 2025 California Building Code, which uses ASCE 7-22 for seismic forces on mechanical equipment, so anchorage is designed for the new machine’s weight and center of gravity. A different footprint often needs new pads or curbs. Paul Industries designs the anchorage with the structural engineer and installs it with the new machine.

What does chiller replacement cost in California include?

A California replacement includes the new low-GWP chiller, rigging, seismic anchorage and any new pad or curb, electrical and piping changes, machinery room updates for the new refrigerant’s safety class, recovery and removal of the old machine, and startup. Paul Industries gives a budget figure from tonnage and a site description, then fixes the price after walking the rigging path and checking structure and electrical service.

How do California electricity rates tilt a chiller replacement decision?

At 21.53 cents per kilowatt-hour for industrial users in 2024, against 8.13 for the country (EIA), an efficiency gain is worth about two and a half times as much as at the national average. A chiller that would be repaired in a low-price state may justify replacement here. Paul Industries runs the comparison with the owner’s tonnage, run hours and tariff.

Which records speed up a chiller diagnosis in California?

Nameplate photos, the refrigerant and its charge, recent alarm and trend logs, the last service report, and the leak inspection and refrigerant addition records kept for CARB and EPA. Those records show whether the fault is new or recurring and whether the 14-day state window is already running. Paul Industries plans the first visit from them and brings the likely parts.

Does Paul Industries work on absorption chillers at California campuses and cogeneration plants?

Yes. Paul Industries repairs absorption chillers driven by steam, hot water or direct firing at campuses, hospitals and cogeneration plants, including solution analysis, crystallization recovery, purge and vacuum work, tube cleaning and controls. Absorption machines use water and lithium bromide rather than a high-GWP refrigerant, which keeps them outside the refrigerant programs that govern vapor compression chillers.

Have a chiller to repair anywhere in California?

Share the nameplate data, refrigerant, alarm history and latest leak records. Call 201-450-8280 or request a quote.